scholarly journals Влияние высоких давлений на формирование новых соединений в сплаве Al-=SUB=-86-=/SUB=-Ni-=SUB=-2-=/SUB=-Со-=SUB=-6-=/SUB=-Gd-=SUB=-6-=/SUB=--=SUP=--=SUP=-*-=/SUP=--=/SUP=-

2022 ◽  
Vol 64 (2) ◽  
pp. 149
Author(s):  
С.Г. Меньшикова ◽  
В.В. Бражкин
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
High Pressure ◽  
Phase Composition ◽  
Precipitation Hardening ◽  
Supersaturated Solid Solution ◽  
Lattice Parameter ◽  
X Ray Diffraction ◽  
X Ray ◽  
Shrinkage Cavities

Abstract The structure, elemental and phase composition of the eutectic alloy Al86Ni2Со6Gd6 (hereinafter referred to as at.%) During the solidification of the melt from 1500oC at a rate of 1000oC/s under high pressure of 3 and 7 GPa have been investigated by X-ray diffraction analysis and electron microscopy. Solidification of the melt under high pressure leads to a change in the phase composition of the alloy and the formation of an anomalously supersaturated solid solution of α-Al (Gd). At a pressure of 7 GPa, new phases were synthesized: Al3Gd * (like Al3U) containing Co and Ni, with a primitive cube structure (cP4/2) with a lattice parameter a = 4.285 ± 0.002 Angstrem and Al8Co4Gd * (like Al8Cr4Gd) with a tetragonal structure (tI26/1) with parameters a = 8.906 ± 0.003 Angstrem and c = 5.150 ± 0.003 Angstrem. The structure of all the samples obtained is homogeneous, dense, finely dispersed, without shrinkage cavities and pores. The average microhardness of the samples is high due to solid solution and precipitation hardening.

Effect of Synthesis Conditions and Actinide Contents on Phase Composition of Actinide Bearing Ceramics

2003 ◽  
Vol 807 ◽  
Author(s):  
A. G. Ptashkin ◽  
S. V. Stefanovsky ◽  
S. V. Yudintsev ◽  
S. A. Perevalov
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Phase Composition ◽  
Fluorite Structure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Synthesis Conditions ◽  
Reducing Conditions ◽  
Dispersive System ◽  
Scanning Electron

ABSTRACTPu-bearing zirconolite and pyrochlore based ceramics were prepared by melting under oxidizing and reducing conditions at 1550 °C. 239Pu content in the samples ranged between ∼10 and ∼50 wt.%. Phase composition of the ceramics and Pu partitioning were studied using X-ray diffraction (XRD) and scanning electron microscopy with energy dispersive system (SEM/EDS). Major phases in the samples were found to be the target zirconolite and pyrochlore as well as a cubic fluorite structure oxide. Normally the Pu content in the Pu host phases was 10–12 wt.%. This corresponds to the Pu content recommended for matrices for immobilization of excess weapons plutonium. At higher Pu content (up to 50 wt.%) additional phases, such as a PuO2-based cubic fluorite-structured solid solution, perovskite, and rutile were found.

Structure of multi-functional calcium phosphates/TiO2 layers deposited on NiTi shape-memory alloy

2017 ◽  
Vol 32 (S1) ◽  
pp. S99-S105
Author(s):  
Tomasz Goryczka ◽  
Karolina Dudek
Keyword(s):  
Electron Microscopy ◽  
Phase Composition ◽  
Martensitic Transformation ◽  
Calcium Phosphates ◽  
Lattice Parameter ◽  
Original Structure ◽  
Niti Shape Memory Alloy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Niti Matrix

The structure of the NiTi matrix covered by multi-layer was studied applying X-ray diffraction techniques supported by electron microscopy. Multi-layer was composed from titanium oxide (passivation) followed by mixture of the hydroxyapatite (HAp) and β-tricalcium phosphate (β-TCP) (electrophoresis). Conditions of deposition as well as sintering did not change the nominal ratio of HAp/TCP and saved their original structure. Also, the passivated NiTi matrix and with HAp/TCP-deposited layer did not change structure. However, sintering, done for HAp/TCP consolidation, introduced local differences in the lattice parameter as well as phase composition of the NiTi matrix. In consequence of that, two-steps martensitic transformation occurred in sintered NiTi/TiO2/Hap–TCP composite.

Effect of high pressure-temperature on silicon layered structures as determined by X-ray diffraction and electron microscopy

2004 ◽  
Vol 27 (1-3) ◽  
pp. 415-418
Author(s):  
J. Bak-Misiuk ◽  
A. Misiuk ◽  
J. Ratajczak ◽  
A. Shalimov ◽  
I. Antonova ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
High Pressure ◽  
Layered Structures ◽  
X Ray Diffraction ◽  
X Ray

scholarly journals Synthesis of Ce1−xPdxO2−δ Solid Solution in Molten Nitrate

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 640
Author(s):  
Hideaki Sasaki ◽  
Keisuke Sakamoto ◽  
Masami Mori ◽  
Tatsuaki Sakamoto
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Solid Solutions ◽  
Photoelectron Spectroscopy ◽  
Synthesis Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation ◽  
Ionic States

CeO2-based solid solutions in which Pd partially substitutes for Ce attract considerable attention, owing to their high catalytic performances. In this study, the solid solution (Ce1−xPdxO2−δ) with a high Pd content (x ~ 0.2) was synthesized through co-precipitation under oxidative conditions using molten nitrate, and its structure and thermal decomposition were examined. The characteristics of the solid solution, such as the change in a lattice constant, inhibition of sintering, and ionic states, were examined using X-ray diffraction (XRD), scanning electron microscopy–energy-dispersive X-ray spectroscopy (SEM−EDS), transmission electron microscopy (TEM)−EDS, and X-ray photoelectron spectroscopy (XPS). The synthesis method proposed in this study appears suitable for the easy preparation of CeO2 solid solutions with a high Pd content.

Elaboration, Structure and Mössbauer Spectroscopy of Nanostructured Fe100−xSix Powders Elaborated by Mechanical Alloying

SPIN ◽  
2017 ◽  
Vol 07 (02) ◽  
pp. 1750002 ◽  
Author(s):  
M. Hemmous ◽  
A. Guittoum
Keyword(s):  
Magnetic Field ◽  
Solid Solution ◽  
Mechanical Alloying ◽  
Hyperfine Magnetic Field ◽  
Lattice Parameter ◽  
X Ray Diffraction ◽  
X Ray ◽  
Grain Sizes ◽  
The Mean ◽  
Xrd Studies

We have studied the effect of the silicon concentration on the structural and hyperfine properties of nanostructured Fe[Formula: see text]Six powders ([Formula: see text], 20, 25 and 30[Formula: see text]at.%) prepared by mechanical alloying. The X-ray diffraction (XRD) studies indicated that after 72[Formula: see text]h of milling, the solid solution bcc-[Formula: see text]-Fe(Si) is formed. The grain sizes, [Formula: see text]D[Formula: see text] (nm), decreases with increasing Si concentration and reaches a minimum value of 11[Formula: see text]nm. We have found that the lattice parameter decreases with increasing Si concentration. The changes in values are attributed to the substitutional dissolution of Si in Fe matrix. From the adjustment of Mössbauer spectra, we have shown that the mean hyperfine magnetic field, [Formula: see text]H[Formula: see text] (T), decreases with increasing Si concentration. The substitutional dependence of [Formula: see text]H[Formula: see text] (T) can be attributed to the effect of p electrons Si influencing electrons d of Fe.

SIZE-INDUCED EFFECTS IN NANOSTRUCTURED NiFe2O4

2010 ◽  
Vol 24 (30) ◽  
pp. 5973-5985
Author(s):  
M. GUNES ◽  
H. GENCER ◽  
T. IZGI ◽  
V. S. KOLAT ◽  
S. ATALAY
Keyword(s):  
Electron Microscopy ◽  
Annealing Temperature ◽  
Structural Parameters ◽  
Hydrothermal Process ◽  
Lattice Parameter ◽  
Effect Of Temperature ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

NiFe 2 O 4 nanoparticles were successfully prepared by a hydrothermal process, and the effect of temperature on them was studied. The particles were annealed at various temperatures ranging from 413 to 1473 K. Studies were carried out using powder X-ray diffraction, scanning electron microscopy, infrared spectroscopy, differential thermal analysis, thermogravimetric analysis and a vibrating sample magnetometer. The annealing temperature had a significant effect on the magnetic and structural parameters, such as the crystallite size, lattice parameter, magnetization and coercivity.

UTILIZATION OF FLY ASH AND CONCRETE RESIDUE IN THE PRODUCTION OF GEOPOLYMER BRICKS

2017 ◽  
Vol 12 (1) ◽  
pp. 63-77 ◽  
Author(s):  
Siriporn Sirikingkaew ◽  
Nuta Supakata
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Phase Composition ◽  
Fly Ash ◽  
Industrial Waste ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

This study presents the development of geopolymer bricks synthetized from industrial waste, including fly ash mixed with concrete residue containing aluminosilicate compound. The above two ingredients are mixed according to five ratios: 100:0, 95:5, 90:10, 85:15, and 80:20. The mixture's physico-mechanical properties, in terms of water absorption and the compressive strength of the geopolymer bricks, are investigated according to the TIS 168-2546 standard. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses are used to investigate the microstructure and the elemental and phase composition of the brick specimens. The results indicate that the combination of fly ash and concrete residue represents a suitable approach to brick production, as required by the TIS 168–2546 standard.

High-pressure study of a nanostructured SnSe1−xSx (x = 0.5) solid solution by in-situ X-ray diffraction and ab-initio calculations

2019 ◽  
Vol 792 ◽  
pp. 536-542
Author(s):  
Larissa da Silva Marques ◽  
Joelma Maria de Oliveira Ferreira ◽  
Querem Hapuque Félix Rebelo ◽  
Angsula Ghosh ◽  
Daniela Menegon Trichês ◽  
...  
Keyword(s):  
Solid Solution ◽  
High Pressure ◽  
Ab Initio Calculations ◽  
Ab Initio ◽  
X Ray Diffraction ◽  
X Ray ◽  
High Pressure Study

scholarly journals Standard Hot Pressing as a Possible Solution to Obtain Dense K0.5Na0.5NbO3 Ceramic Doped by Er2O3 and Yb2O3

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4171 ◽  
Author(s):  
Paweł Rutkowski ◽  
Jan Huebner ◽  
Adrian Graboś ◽  
Dariusz Kata ◽  
Dariusz Grzybek ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Rare Earth ◽  
Phase Composition ◽  
Powder Mixture ◽  
Hot Pressing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ultrasonic Methods ◽  
Scanning Electron

In this study, the influence of the addition of rare earth oxides on the phase composition and density of KNN piezoelectric ceramics was investigated. The initial powders of Na2CO3 and K2CO3 were dried at 150 °C for 2 h. Then, a powder mixture for synthesis was prepared by adding a stoichiometric amount of Nb2O5 and 5 and 10 wt % overabundance of Na2CO3. All powders were mixed by ball-milling for 24 h and synthesized at 950 °C. The phase composition of the reaction bed was checked by means of X-ray diffraction (XRD). It had an appearance of tetragonal and monoclinic K0.5Na0.5NbO3 (KNN) phases. Then, 1 and 2 wt % of Er2O3 and Yb2O3, were added to the mixture. Green samples of 25 mm diameter and 3 mm thickness were prepared and sintered by hot pressing at 1000 °C for 2 h under 25 MPa pressure. The final samples were investigated via scanning electron microscopy (SEM)-energy-dispersive X-ray spectroscopy (EDS), XRD, Rietveld, and ultrasonic methods. Phase analysis showed tetragonal and orthorhombic KNN phases, and a contamination of (K2CO3·1.5H2O) was present. The obtained KNN polycrystals had a relative density above 95%. Texturing of the material was confirmed as a result of hot pressing.

Sign in / Sign up

Export Citation Format

Share Document