scholarly journals Strength of RC Beam using Geopolymer Concrete and Adopting Bubble Technology

2021 ◽  
Vol 9 (VI) ◽  
pp. 2812-2816
Author(s):  
Abhinay I. Deshmukh
Keyword(s):  
Hollow Spheres ◽  
Experimental Investigations ◽  
Geopolymer Concrete ◽  
Tension Zone ◽  
Portland Cement Concrete ◽  
Dead Weight ◽  
Conventional Concrete ◽  
Modes Of Failure ◽  
Calcium Silicate Hydrates ◽  
Load Carrying

The Bubble Deck technology developed in Europe makes use of high-density polyethylene hollow spheres to replace the ineffective concrete in the centre of the slab, thus decreasing the dead weight and increasing the efficiency of the floor. Concrete is good in compression and hence is more useful in the compression region than in the tension region. The reduction in concrete can be done by replacing the tension zone concrete. Keeping the same idea in mind, an attempt has been made to find out the effectiveness of plastic bubbles by replacing concrete in the tension zone of Ordinary Portland Cement Concrete (OPCC) and Geopolymer Concrete (GPC) beam. Geopolymer Concrete does not form calcium- silicate-hydrates (CSHs) for matrix formation and strength like OPCC but utilizes the polycondensation of silica and alumina precursors to attain structural strength. In this project, M25 concrete mix is used to prepare both OPCC and GPC beams. The trial mix is tested for compressive strength. Flexure test is done is done for 28 days of curing of the beams. This paper presents the results of the experimental investigations carried out to determine and to compare the flexural behaviour of geopolymer concrete (GPC) beams with conventional concrete beams of same grade. The beams were tested under two point monotonic loading. Performance aspects such as load carrying capacity, first crack load, ultimate load, load-deflection behaviour, moment-curvature behaviour, crack width, crack spacing and the modes of failure of both types of beams were studied. The test results showed that the geopolymer concrete exhibits better performance compared to conventional concrete of same grade.

scholarly journals Behavior of Geopolymer Concrete Confined by Circular Hoops

2018 ◽  
Vol 159 ◽  
pp. 01018
Author(s):  
Muslikh ◽  
N. K. Anggraini ◽  
D. Hardjito ◽  
Antonius
Keyword(s):  
Portland Cement ◽  
Concrete Cover ◽  
Geopolymer Concrete ◽  
Test Results ◽  
Portland Cement Concrete ◽  
Reinforcing Bars ◽  
Cement Concrete ◽  
Conventional Concrete ◽  
K Value ◽  
Steel Bar

This paper discusses the behavior of geopolymer concrete subjected to passive confinement under compression loads. The confinement is induced by the use of lateral hoops, assembled from un-deformed reinforcing bars. To compare the effect of confinement, identical specimens were produced using conventional concrete with the similar concrete compressive strength. The cylinder specimens were 100 mm in diameter and 200 mm in height, and the hoops were placed on the outer most fibers of the cylinders, perpendicular to the line of loading, with no concrete cover. The parameters analyzed in this study were the steel bar to concrete volumetric ratio, the hoop spacings and the steel yield stresses. The experimental results show that unconfined geopolymer concrete were very brittle compared to the unconfined Portland cement concrete. The strength enhancement (K value) of the confined geopolymer concrete was higher than K value of Portland cement concrete. Confined geopolymer concrete also has better deformability compared to the confined Portland cement concrete. The average confinement effectiveness of geopolymer concrete also has a higher value than that commonly used in the Indonesian Concrete Standard (SNI), that is 4.1. The results were further assessed to the most recent experimental test results conducted in this area.

scholarly journals Filler slab with partial replacement of cement by Eggshell powder

2019 ◽  
Vol 8 (10) ◽  
pp. 3980-3984
Keyword(s):  
Construction Industry ◽  
Cost Effective ◽  
Partial Replacement ◽  
Tension Zone ◽  
Dead Weight ◽  
Conventional Concrete ◽  
Cost Effective Method ◽  
Tensile Forces ◽  
Lightweight Filler ◽  
Powdered Form

Currently India has taken a major initiative in developing the infrastructure to meet the requirements of globalization in the construction industry. Considering building element like slab, more concrete is wasted in the tension zone, since the tensile forces are taken by the steel reinforcement. To overcome this wastage of concrete in tension zone, a new cost effective method called as Filler slab technique is used. Low price and lightweight filler substance like Mangalore tiles, that will decrease the dead weight in addition to the total cost of this slab to some degree. Being environmentally accountable, the utilization of waste substances is a Vital step in creating a sustainable future. The Eggshell, which is usually disposed as a poultry waste can be used as an alternate of cement in powdered form, since the shell is made up of Calcium having a chemical composition same as limestone. Partial replacement of cement by eggshell powder is done in different proportions like 2.5%, 5%, 7.5% & 10%. In this paper, the filler slab has been created additional cost effective with the addition of eggshell powder because partial replacement of cement. Following a healing period of 28 days, there's a version in compression and flexural strength of concrete using eggshell powder compared to conventional concrete

Experimental investigations on compressive, impact and prediction of stress-strain of fly ash-geopolymer and portland cement concrete

2020 ◽  
Vol 40 (7) ◽  
pp. 583-590
Author(s):  
Nagajothi S ◽  
Elavenil S
Keyword(s):  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Impact Resistance ◽  
Geopolymer Concrete ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Stress Strain ◽  
River Sand ◽  
Conventional Concrete ◽  
Strain Behaviour

AbstractThe recent technology of geopolymer concrete is a substitute material for ordinary portland cement concrete which is produced from the polycondensation reaction of aluminosilicate materials with alkaline activator solutions. The cost of river sand is high since the demand for the same is also high. Manufactured sand is used as a replacement material for river sand in geopolymer concrete. This paper mainly focuses to find the properties of fly ash (FA) – based geopolymer concrete under ambient cured temperature like compressive strength, stress strain behaviour, modulus of elasticity, Poission’s ratio and impact resistance. The result of geopolymer concrete is compared with ordinary portland cement concrete. The elasticity modulus and Poission’s ratio of geopolymer concrete are lower than conventional concrete. The Stress-strain behaviour of geopolymer concrete is similar to conventional concrete. The impact resistance of geopolymer concrete is very good when compared with conventional concrete.

scholarly journals Effect of Hybrid Fibres on the Durability Characteristics of Ternary Blend Geopolymer Concrete

2021 ◽  
Vol 5 (10) ◽  
pp. 279
Author(s):  
V. Sathish Kumar ◽  
N. Ganesan ◽  
P. V. Indira
Keyword(s):  
Ternary Blend ◽  
Experimental Investigations ◽  
Geopolymer Concrete ◽  
Acid Attack ◽  
Polypropylene Fibres ◽  
Hybrid Form ◽  
Conventional Concrete ◽  
Durability Properties ◽  
Safe Level ◽  
Source Materials

The need to develop sustainable concrete in the civil infrastructure industry increases day by day, resulting in new eco-friendly materials such as geopolymer concrete. Geopolymer concrete is one of the eminent alternatives to conventional concrete for sustainable development by reducing the carbon footprint. Ternary blend geopolymer concrete (TGPC) is a sustainable and environmentally friendly concrete produced with three different source materials to form a binder. The main advantage of TGPC is that it possesses densely packed particles of different shapes and sizes, which results in improved properties. This paper deals with the experimental investigations to evaluate the durability properties of plain and hybrid fibre reinforced TGPC. The durability of concrete is defined as the ability to withstand a safe level of serviceability and different environmental exposure conditions without any significant repair and rehabilitation throughout the service life. Conventional concrete is vulnerable to cracking due to its low tensile and durability properties. The TGPC considered in this work consists of fly ash, GGBS and metakaolin as source materials, selected mainly based on the material’s silica and alumina content, shape, size, and availability. The grade of concrete considered was M55. The main variables considered in this study were the proportions of crimped steel fibres (Vf), viz., 0.5% and 1% and proportions of polypropylene fibres (Vp)viz., 0.1%, 0.15%, 0.20% and 0.25%. The durability properties like water absorption, sorptivity, resistance to marine attack, acid attack, sulphate attack, and abrasion were studied in this investigation. The experimental test results were compared with the requirements provided in the standard/literature and found to be well within limits. The study also indicates that the inclusion of fibres in a hybrid form significantly improves the durability parameters of TGPC. The TGPC with 1% steel fibre and 0.15% polypropylene fibre performs better than the other combination of fibres considered in this experimental investigation.

Flexural Performance of Reinforced Concrete Built-up Beams with SIFCON

2020 ◽  
Vol 38 (5A) ◽  
pp. 669-680
Author(s):  
Ghazwan K. Mohammed ◽  
Kaiss F. Sarsam ◽  
Ikbal N. Gorgis
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Conventional Concrete ◽  
Flexural Performance ◽  
Load Carrying ◽  
Fiber Concrete

The study deals with the effect of using Slurry infiltrated fiber concrete (SIFCON) with the reinforced concrete beams to explore its enhancement to the flexural capacity. The experimental work consists of the casting of six beams, two beams were fully cast by conventional concrete (CC) and SIFCON, as references. While the remaining was made by contributing a layer of SIFCON diverse in-depth and position, towards complete the overall depths of the built-up beam with conventional concrete CC. Also, an investigation was done through the control specimens testing about the mechanical properties of SIFCON. The results showed a stiffer behavior with a significant increase in load-carrying capacity when SIFCON used in tension zones. Otherwise high ductility and energy dissipation appeared when SIFCON placed in compression zones with a slight increment in ultimate load. The high volumetric ratio of steel fibers enabled SIFCON to magnificent tensile properties.

scholarly journals Practical Prediction Models of Tensile Strength and Reinforcement-Concrete Bond Strength of Low-Calcium Fly Ash Geopolymer Concrete

Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 875
Author(s):  
Chenchen Luan ◽  
Qingyuan Wang ◽  
Fuhua Yang ◽  
Kuanyu Zhang ◽  
Nodir Utashev ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Fly Ash ◽  
Bond Strength ◽  
Prediction Models ◽  
Splitting Tensile Strength ◽  
Geopolymer Concrete ◽  
Structural Factors ◽  
Test Results ◽  
Portland Cement Concrete ◽  
Low Calcium

There have been a few attempts to develop prediction models of splitting tensile strength and reinforcement-concrete bond strength of FAGC (low-calcium fly ash geopolymer concrete), however, no model can be used as a design equation. Therefore, this paper aimed to provide practical prediction models. Using 115 test results for splitting tensile strength and 147 test results for bond strength from experiments and previous literature, considering the effect of size and shape on strength and structural factors on bond strength, this paper developed and verified updated prediction models and the 90% prediction intervals by regression analysis. The models can be used as design equations and applied for estimating the cracking behaviors and calculating the design anchorage length of reinforced FAGC beams. The strength models of PCC (Portland cement concrete) overestimate the splitting tensile strength and reinforcement-concrete bond strength of FAGC, so PCC’s models are not recommended as the design equations.

scholarly journals Behavior of Quarry Rock Dust, Fly Ash and Slag Based Geopolymer Concrete Columns Reinforced with Steel Fibers under Eccentric Loading

2021 ◽  
Vol 11 (15) ◽  
pp. 6740
Author(s):  
Rana Muhammad Waqas ◽  
Faheem Butt
Keyword(s):  
Fly Ash ◽  
Concrete Cover ◽  
Steel Fibers ◽  
Structural Behavior ◽  
Partial Replacement ◽  
Geopolymer Concrete ◽  
Fiber Reinforced ◽  
Conventional Concrete ◽  
Source Materials ◽  
Rock Dust

Geopolymer concrete, also known as an earth-friendly concrete, has been under continuous study due to its environmental benefits and a sustainable alternative to conventional concrete construction. The supplies of many source materials, such as fly ash (FA) or slag (SG), to produce geopolymer concrete (GPC) may be limited; however, quarry rock dust (QRD) wastes (limestone, dolomite, or silica powders) formed by crushing rocks appear virtually endless. Although significant experimental research has been carried out on GPC, with a major focus on the mix design development, rheological, durability, and mechanical properties of the GPC mixes; still the information available on the structural behavior of GPC is rather limited. This has implications in extending GPC application from a laboratory-based technology to an at-site product. This study investigates the structural behavior of quarry-rock-dust-incorporated fiber-reinforced GPC columns under concentric and eccentric loading. In this study, a total of 20 columns with 200 mm square cross-section and 1000 mm height were tested. The FA and SG were used as source materials to produce GPC mixtures. The QRD was incorporated as a partial replacement (20%) of SG. The conventional concrete (CC) columns were prepared as the reference specimens. The effect of incorporating quarry rock dust as a replacement of SG, steel fibers, and loading conditions (concentric and eccentric loading) on the structural behavior of GPC columns were studied. The test results revealed that quarry rock dust is an adequate material that can be used as a source material in GPC to manufacture structural concrete members with satisfactory performance. The general performance of the GPC columns incorporating QRD (20%) is observed to be similar to that of GPC columns (without QRD) and CC columns. The addition of steel fibers considerably improves the loading capacity, ductility, and axial load–displacement behavior of the tested columns. The load capacities of fiber-reinforced GPC columns were about 5–7% greater in comparison to the CC columns. The spalling of concrete cover at failure was detected in all plain GPC columns, whereas the failure mode of all fiber-reinforced GPC columns is characterized with surface cracking leading to disintegration of concrete cover.

scholarly journals Experimental Investigation on Composite Deck Slab Made of Cold-Formed Profiled Steel Sheeting

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 229
Author(s):  
Siva Avudaiappan ◽  
Erick I. Saavedra Flores ◽  
Gerardo Araya-Letelier ◽  
Walter Jonathan Thomas ◽  
Sudharshan N. Raman ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Test Results ◽  
Shear Connectors ◽  
Modes Of Failure ◽  
Deck Slabs ◽  
Load Carrying ◽  
Composite Slabs ◽  
Ultimate Load Carrying Capacity ◽  
Ductility Ratio ◽  
Deck Slab

An experimental investigation is performed on various cold-formed profiled sheets to study the connection behavior of composite deck slab actions using bolted shear connectors. Various profiles like dovetailed (or) re-entrant profiles, rectangular profiles and trapezoidal profiles are used in the present investigation. This experimental investigation deals with the evaluation of various parameters such as the ultimate load carrying capacity versus deflection, load versus slip, ductility ratio, strain energy and modes of failure in composite slab specimens with varying profiles. From the test results the performance of dovetailed profiled composite slabs’ resistance is significantly higher than the other two profiled composite deck slabs.

Performance Characteristics of Concrete Produced with Fluidized Bed Combustion Ash Residue

1988 ◽  
Vol 136 ◽  
Author(s):  
A. E. Bland ◽  
C. E. Jones ◽  
J. G. Rose ◽  
J. L. Harness
Keyword(s):  
Fluidized Bed ◽  
Performance Characteristics ◽  
Strength Development ◽  
Fluidized Bed Combustion ◽  
Portland Cement Concrete ◽  
Conventional Concrete ◽  
Setting Times ◽  
Pulverized Fuel ◽  
Tennessee Valley ◽  
Pulverized Fuel Ash

ABSTRACTOver the last five years, the Kentucky Energy Cabinet (KEC) and the Tennessee Valley Authority (TVA) have developed and demonstrated the production of concrete from atmospheric fluidized bed combustion (AFBC) spent bed (SB) ash, and pulverized fuel ash (PFA). This AFBC concrete contains no cement and relies on the reaction of residual lime in the SB ash to react with the pozzolan PFA to form cementitious products. The SB ash is prehydrated in order to reduce exothermic lime hydration reactions and minimize molar volume expansion. Laboratory tests were conducted to establish the performance characteristics of AFBC concretes relative to conventional concrete. AFBC concretes exhibit slower strength gain characteristics, but long term (60 day), unconfined compressive strengths of 5,000 psi have been documented. This slow strength development is typical of pozzolanic concretes. AFBC concrete is more flexible and less brittle than conventional Portland cement concrete, as evidenced by its much lower modulus of elasticity. Setting times for AFBC concretes are extended, requiring the use of accelerators under certain applications. Field demonstrations of the AFBC concretes in ready mix concrete, masonry units, and road base applications have indicated excellent workability and finishing characteristics and confirm the laboratory performance characteristics.The paper describes the results of the testing program with emphasis on the ash chemistry/conditioning, the performance characteristics and field demonstrations.

Improving the structural performance of reinforced geopolymer concrete incorporated with hazardous heavy metal waste ash

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Suresh Kumar Arunachalam ◽  
Muthukannan Muthiah ◽  
Kanniga Devi Rangaswamy ◽  
Arunkumar Kadarkarai ◽  
Chithambar Ganesh Arunasankar
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Medical Waste ◽  
Source Material ◽  
Geopolymer Concrete ◽  
Deformation Capacity ◽  
Cement Concrete ◽  
Content Type ◽  
Load Carrying ◽  
Reinforced Cement

Purpose Demand for Geopolymer concrete (GPC) has increased recently because of its many benefits, including being environmentally sustainable, extremely tolerant to high temperature and chemical attacks in more dangerous environments. Like standard concrete, GPC also has low tensile strength and deformation capacity. This paper aims to analyse the utilization of incinerated bio-medical waste ash (IBWA) combined with ground granulated blast furnace slag (GGBS) in reinforced GPC beams and columns. Medical waste was produced in the health-care industry, specifically in hospitals and diagnostic laboratories. GGBS is a form of industrial waste generated by steel factories. The best option to address global warming is to reduce the consumption of Portland cement production and promote other types of cement that were not a pollutant to the environment. Therefore, the replacement in ordinary Portland cement construction with GPC is a promising way of reducing carbon dioxide emissions. GPC was produced due to an alkali-activated polymeric reaction between alumina-silicate source materials and unreacted aggregates and other materials. Industrial pollutants such as fly ash and slag were used as raw materials. Design/methodology/approach Laboratory experiments were performed on three different proportions (reinforced cement concrete [RCC], 100% GGBS as an aluminosilicate source material in reinforced geopolymer concrete [GRGPC] and 30% replacement of IBWA as an aluminosilicate source material for GGBS in reinforced geopolymer concrete [IGRGPC]). The cubes and cylinders for these proportions were tested to find their compressive strength and split tensile strength. In addition, beams (deflection factor, ductility factor, flexural strength, degradation of stiffness and toughness index) and columns (load-carrying ability, stress-strain behaviour and load-deflection behaviours) of reinforced geopolymer concrete (RGPC) were studied. Findings As shown by the results, compared to Reinforced Cement Concrete (RCC) and 100% GGBS based Reinforced Geopolymer Concrete (GRGPC), 30% IBWA and 70% GGBS based Reinforced Geopolymer Concrete (IGRGPC) (30% IBWA–70% GGBS reinforced geo-polymer concrete) cubes, cylinders, beams and columns exhibit high compressive strength, tensile strength, flexural strength, load-carrying ability, ultimate strength, stiffness, ductility and deformation capacity. Originality/value All the results were based on the experiments done in this research. All the result values obtained in this research are higher than the theoretical values.

Sign in / Sign up

Export Citation Format

Share Document