scholarly journals Performance Based Seismic Design of Reinforced Concrete Building by Non-Linear Static Analysis

2021 ◽  
Vol 9 (VII) ◽  
pp. 1748-1752
Author(s):  
Prof. Pallavi K. Pasnur
Keyword(s):  
Seismic Design ◽  
Plastic Hinge ◽  
Time History ◽  
Performance Level ◽  
Economic Losses ◽  
Earthquake Resistant Design ◽  
Non Linear ◽  
Rc Building ◽  
Performance Based Seismic Design ◽  
Design Earthquake

In past two decades earthquake disasters in the world have shown that significant damage occurred even when the buildings were designed as per the conventional earthquake-resistant design philosophy (force-based approach) exposing the inability of the codes to ensure minimum performance of the structures under design earthquake. The performance based seismic design (PBSD), evaluates how the buildings are likely to perform under a design earthquake. As compared to force-based approach, PBSD provides a methodology for assessing the seismic performance of a building, ensuring life safety and minimum economic losses. The non-linear static procedures also known as time history analysis are used to analyze the performance of structure . Plastic hinge formation patterns, plastic rotation, drift ratio and other parameters are selected as performance criterias to define different performance level. In this paper, a five-storey RC building is modelled and designed as per IS 456:2000 and analyzed for lmmediate occupancy performance level in ETABS2015 softwere. Analysis is carried out as per FEMA P58 PART 1 & 2. Plastic hinges as per FEMA273. From the analysis, it is checked that the performance level of the building is as per the assumption

scholarly journals ANALISIS PERIODA BANGUNAN DINDING GESER DENGAN BASE ISOLATOR AKIBAT GAYA GEMPA

Teras Jurnal ◽  
2018 ◽  
Vol 7 (2) ◽  
pp. 263
Author(s):  
Mul Muliadi Adi ◽  
M. Kabir Kabir Ihsan
Keyword(s):  
Seismic Design ◽  
Time History ◽  
Shear Wall ◽  
Braced Frame ◽  
Moment Resisting Frame ◽  
Rigid Frame ◽  
Base Isolator ◽  
Non Linear ◽  
Moment Resisting ◽  
Performance Based Seismic Design

Bangunan yang hancur oleh gempa dapat dicegah dengan memperkuat struktur bangunan terhadap gaya gempa yang bekerja padanya. Perkuatan bangunan dapat dilakukan dengan memperkaku bangunan dalam arah lateral yaitu <em>moment resisting frame</em> (<em>rigid frame</em>), <em>braced frame</em> dan <em>shear wall</em>. Bangunan dinding geser merupakan salah satu jenis <em>bangunan</em> tahan gempa gedung beton bertulang menggunakan sistem rangka struktur yang dikombinasikan. Kinerja gedung akan bertambah dan menjadi optimal jika pola penempatan <em>dinding geser</em> serta metode analisanya tepat. Sistem lainnya dalam mengurangi kerusakan bangunan akibat gempa dengan <em>performance based seismic design</em> yaitu dengan menggunakan <em>base isolator.</em>, yang memanfaatkan teknik analisa non-linear berbasis komputer untuk menganalisa perilaku inelastis struktur dari berbagai macam intensitas gerakan tanah (<em>gempa</em>), sehingga dapat diketahui kinerjanya pada kondisi kritis. Tujuan penelitian ini dilakukan untuk mengetahui perioda dalam penggunaan <em>base isolator </em>dengan yang tanpa menggunakan <em>base isolator,</em> pada bangunan sistem ganda, lantai 10 tingkat, bentuk beraturan pada bangunan dinding geser. Analisis data yang dilakukan dengan menggunakan bantuan <em>software </em>komputer <em>SAP2000</em>. Pembebanan pada gedung didasarkan pada peraturan bangunan gedung beton bertulang dan analisa dinamik <em>Time History Modal Analysi</em>s struktur dalam Tata Cara Perencanaan Ketahanan Gempa Untuk Struktur Bangunan Gedung Dan Non Gedung (SNI 1726:2012). Dari hasil penelitian ini dapat diketahui bahwa penggunaan <em>base isolator</em> memperbesar perioda alami. Nilai perioda pada dinding geser dan dinding geser <em>base isolator</em> besarnya berturut-turut 0.988 detik dan 2.465 detik. Hal ini menyebabkan gaya gempa yang bekerja menjadi lebih kecil.

Vector-Valued Uniform Hazard Spectra

2012 ◽  
Vol 28 (4) ◽  
pp. 1549-1568 ◽  
Author(s):  
Shun-Hao Ni ◽  
De-Yi Zhang ◽  
Wei-Chau Xie ◽  
Mahesh D. Pandey
Keyword(s):  
Seismic Hazard ◽  
Seismic Design ◽  
Hazard Analysis ◽  
Occurrence Rate ◽  
Simultaneous Occurrence ◽  
Uniform Hazard Spectra ◽  
Design Spectrum ◽  
Performance Based Seismic Design ◽  
Design Earthquake ◽  
Vector Valued

Uniform hazard spectra (UHS) have been used as design earthquakes in several design codes. However, as the results from scalar probabilistic seismic hazard analysis (PSHA), UHS do not provide knowledge about the simultaneous occurrence of spectral accelerations at multiple vibration periods. The concept of a single “design earthquake” is then lost on a UHS. In this study, a vector-valued PSHA combined with scalar PSHA is applied to establish an alternative design spectrum, named vector-valued UHS (VUHS). Vector-valued seismic hazard deaggregation (SHD) is also performed to determine the design earthquake in terms of magnitude, distance, and occurrence rate for the VUHS. The proposed VUHS preserves the essence of the UHS and can also be interpreted as a single design earthquake. To simplify the procedure for generating the VUHS, so that they can be easily incorporated into performance-based seismic design, an approximate method is also developed.

Direct Displacement Procedure for Performance-Based Seismic Design of Mid-Rise Wood-Framed Structures

2009 ◽  
Vol 25 (3) ◽  
pp. 583-605 ◽  
Author(s):  
Wei Chiang Pang ◽  
David V. Rosowsky
Keyword(s):  
Seismic Design ◽  
Response Spectrum ◽  
Design Procedure ◽  
Time History ◽  
Time History Analysis ◽  
Nonlinear Time History Analysis ◽  
Framed Structures ◽  
History Analysis ◽  
Performance Based Seismic Design ◽  
Nonlinear Time History

This paper presents a direct displacement design (DDD) procedure that can be used for seismic design of multistory wood-framed structures. The proposed procedure is applicable to any pure shear deforming system. The design procedure is a promising design tool for performance-based seismic design since it allows consideration of multiple performance objectives (e.g., damage limitation, safety requirements) without requiring the engineer to perform a complex finite element or nonlinear time-history analysis of the complete structure. A simple procedure based on normalized modal analysis is used to convert the code-specified acceleration response spectrum into a set of interstory drift spectra. These spectra can be used to determine the minimum stiffness required for each floor based on the drift limit requirements. Specific shear walls can then be directly selected from a database of backbone curves. The procedure is illustrated on the design of two three-story ATC-63 archetype buildings, and the results are validated using nonlinear time-history analysis.

scholarly journals Direct displacement-based seismic design of concrete buildings

2000 ◽  
Vol 33 (4) ◽  
pp. 421-444 ◽  
Author(s):  
M.J.N. Priestley ◽  
M.J. Kowalsky
Keyword(s):  
Seismic Design ◽  
Design Procedure ◽  
Time History ◽  
Initial Stiffness ◽  
Concrete Buildings ◽  
History Analysis ◽  
Starting Point ◽  
Displacement Profile ◽  
Displacement Based ◽  
Design Earthquake

A seismic design procedure is developed to enable concrete buildings to be designed to achieve a specified acceptable level of damage under the design earthquake. The acceptable limit is defined as a displacement profile related to limit material strains or code specified drift limits. In this procedure, the elastic properties, including initial stiffness, strength and period, are the end product of the design rather than the starting point. It is shown that the procedure is simple to apply, and results in significant differences from the more conventional force-based procedure. Designs for multi-storey frame and wall buildings are presented, and target displacements are compared with results from inelastic time-history analysis.

scholarly journals The seismic response of inelastic structures

1975 ◽  
Vol 8 (3) ◽  
pp. 192-203
Author(s):  
R. D. Sharpe ◽  
A. J. Carr
Keyword(s):  
Seismic Design ◽  
Design Method ◽  
Plastic Hinge ◽  
Degree Of Freedom ◽  
Axial Loads ◽  
Earthquake Excitation ◽  
Inelastic Structures ◽  
Dynamic Analyses ◽  
Non Linear ◽  
Seismic Design Method

A thirteen storey, two bay, reinforced concrete framed structure is subjected to a series of non-linear, dynamic analyses in an attempt to find some correlation between the damaging potential of various digitised earthquakes and their relative strengths which have been computed in a variety of ways. Much of the previous work in this field has been with respect to simple one degree of freedom systems and these do not appear to give any indication of the correlation that could be expected for a non-linear multi-degree of freedom structure. The results show the effects of the different scalings of the various earthquakes and compare these with those obtained for the familiar North-South component of the May 18, 1940 El Centro earthquake. These results highlight the difficulty of trying to relate the use of such a dynamic earthquake analysis to the present pseudo-static code requirements. Further, the results of the analyses show also the great difference between the present assumption of the plastic hinge distributions, used in the ultimate seismic design method, and those observed during the earthquake excitation with the consequences on the lower-floor column axial loads.

scholarly journals Improvement of the Performance-Based Seismic Design Method of Cable Supported Bridges with the Resilient-Friction Base Isolation Systems

2020 ◽  
Vol 10 (11) ◽  
pp. 3942 ◽  
Author(s):  
Heungbae Gil ◽  
Kyoungbong Han ◽  
Junho Gong ◽  
Dooyong Cho
Keyword(s):  
Seismic Design ◽  
Design Method ◽  
Response Spectrum ◽  
Design Procedure ◽  
Time History ◽  
Modal Shape ◽  
Ground Acceleration ◽  
Performance Based Seismic Design ◽  
Seismic Design Method ◽  
Shape Analyses

In areas of civil engineering, the resilient friction base isolator (R-FBI) system has been used due to its enhanced isolation performance under seismic excitations. However, because nonlinear behavior of the R-FBI should be reflected in seismic design, effective stiffness (Keff) of the R-FBI is uniformly applied at both peak ground acceleration (PGA) of 0.08 g and 0.154 g which use a multimodal response spectrum (RS) method analysis. For rational seismic design of bridges, it should be required to evaluate the dynamics of the R-FBI from in-field tests and to improve the seismic design procedure based on the performance level of the bridges. The objective of this study is to evaluate the dynamics of the R-FBI and to suggest the performance-based seismic design method for cable-supported bridges with the R-FBI. From the comparison between the experiments’ results and modal shape analyses, the modal shape analyses using primary (Ku) or infinite stiffness (fixed end) showed a great agreement with the experimental results compared to the application of Keff in the shape analysis. Additionally, the RS or nonlinear time history method analyses by the PGA levels should be applied by reflecting the dynamic characteristics of the R-FBI for the reasonable and efficient seismic design.

Discussion on Drift Limit of Fully Operational Performance Level for RC Structures

2010 ◽  
Vol 163-167 ◽  
pp. 1175-1179
Author(s):  
Zi Xiong Guo ◽  
Qun Xian Huang ◽  
Yang Liu
Keyword(s):  
Seismic Design ◽  
Performance Level ◽  
Service Performance ◽  
Operational Performance ◽  
Test Results ◽  
Structural Components ◽  
Rc Structures ◽  
Calculation Results ◽  
Performance Based Seismic Design ◽  
Drift Limit

In accordance with the philosophy of performance based seismic design (PBSD), the fully operational performance level (or service performance level) for frequently occurring earthquakes and the criteria for determining its allowable drift indices is discussed in this paper. To determine the allowable drift limits of the service performance level for frequently occurring earthquake, it is important that not only the degree of damage of nonstructural members but also the degree of cracking in structural components should be controlled. Based on an analysis of test results and calculation results, a series of allowable drift index limits that conform to the fully operational performance level of RC structures are presented.

scholarly journals Seismic Behavior of a Class of Mixed Reinforced Concrete-Steel Buildings Subjected to Near-Fault Motions

2021 ◽  
Vol 6 (12) ◽  
pp. 172
Author(s):  
Paraskevi K. Askouni ◽  
George A. Papagiannopoulos
Keyword(s):  
Reinforced Concrete ◽  
Seismic Response ◽  
Seismic Design ◽  
Seismic Behavior ◽  
Time History ◽  
Steel Buildings ◽  
Seismic Codes ◽  
Near Fault ◽  
Non Linear ◽  
Story Drift

This paper investigates the seismic behavior of a class of mixed reinforced concrete­–­steel buildings. In particular, mixed buildings constructed by r/c (reinforced concrete) at their lower story(ies) and structural steel at their upper story(ies) are studied from the viewpoint of their wide application in engineering praxis. The need to investigate the seismic behavior for this type of mixed buildings arises from the fact that the existent literature is small and that modern seismic codes do not offer specific seismic design recommendations for them. To study the seismic behavior of mixed r/c-steel buildings, a 3-D numerical model is employed and five realistic r/c-steel mixed buildings are simulated. Two cases of the support condition, i.e., fixed or pinned, of the lowest steel story to the upper r/c one are examined. The r/c and steel parts of the mixed buildings are initially designed as separate structures by making use of the relevant seismic design guidelines of Eurocode 8, and then the seismic response of these buildings is computed through non-linear time-history analyses. The special category of near-fault seismic motions is selected in these time-history analyses to force the mixed r/c-steel buildings under study to exhibit a strong non-linear response. Seismic response indices in terms of inter-story drift ratio, residual inter-story drift ratio and peak floor absolute accelerations are computed. The maximum values of these indices are discussed by comparing the two aforementioned kinds of support conditions and checking the satisfaction of specific seismic performance limits. Conclusions regarding the expected seismic behavior of mixed r/c-steel buildings under near-fault seismic motions are drawn. Finally, the need to introduce specific design recommendations for mixed r/c-steel buildings in modern seismic codes is stressed.

Evaluation of Structure Performance under Seismic Load with Non-Liner Time History on High-Rise Building Affected by Kendeng Fault Earthquake Simulation

2021 ◽  
Vol 879 ◽  
pp. 232-242
Author(s):  
A.N. Refani ◽  
Yuyun Tajunnisa ◽  
K. Yudoprasetyo ◽  
F. Ghifari ◽  
D.I. Wahyudi
Keyword(s):  
Linear Time ◽  
Time History ◽  
Time History Analysis ◽  
Performance Level ◽  
Ground Movement ◽  
Seismic Load ◽  
Earthquake Simulation ◽  
Geophysical Research ◽  
History Analysis ◽  
Non Linear

Indonesia is a country located in the convergence of small plates and large plates. Furthermore, this causes Indonesia to be high potentially to earthquake hazards. The newest geological research published by Geophysical Research Letter (2016) shows the existence of Fault Kendeng, a fault stretches along 300 km from South Semarang, Central Java, to East Java with a movement of 0,05 millimeter per year [1]. As a result of its research, an evaluation using a non-linear time history analysis for structural buildings is necessary. The objective of this study is to evaluate structural buildings using a non-linear time history analysis. This study applies DSHA (Deterministic Seismic Hazard Analysis) method to obtain acceleration time history on bedrocks. Since the record of ground movement in Indonesia is limited, the attenuation function equation used to scale and match other country’s time acceleration history data. SSA (Site-Specific Analysis) is used to propagate earthquake acceleration from bedrocks to the surface. The earthquake acceleration on the surface generates as the earthquake load on the buildings. The results of Kendeng fault earthquake simulation using non-linear time history analysis shows that column members capacity is more robust than beam members capacity which the beam collapse mechanism occurs initially. From the maximum total drift ratio result, when the Kendeng fault earthquake occurs, the building structure performance level is at collapse prevention level Based on ATC-40 [2]. This research result shows that 96,7% of plastic hinge has not yielded. However, some elements are already damaged. Since most damage members are column, then it may require column strengthening to enhance maximum performance level at life safety condition category.

Sign in / Sign up

Export Citation Format

Share Document