scholarly journals Comparative analysis of numerical computational techniques for determination of the wind turbine aerodynamic performances

2020 ◽  
pp. 175-175
Author(s):  
Bojan Peric ◽  
Aleksandar Simonovic ◽  
Milos Vorkapic
Keyword(s):  
Wind Turbine ◽  
Pressure Coefficient ◽  
Turbine Blades ◽  
Turbulence Models ◽  
Numerical Approach ◽  
Power Coefficient ◽  
Future Research ◽  
Computational Techniques ◽  
Thrust Coefficient ◽  
Aerodynamic Performances

The purpose of this paper is to explore and define an adequate numerical setting for the computation of aerodynamic performances of wind turbines of various shapes and sizes, which offers the possibility of choosing a suitable approach of minimal complexity for the future research. Here, mechanical power, thrust, power coefficient, thrust coefficient, pressure coefficient, pressure distribution along the blade, relative velocity contoure at different wind speeds and streamlines were considered by two different methods: the blade element momentum (BEM) and computational fluid dynamics (CFD), within which three different turbulence models were analyzed. The estimation of the mentioned aerodynamic performances was carried out on two different wind turbine blades. The obtained solutions were compared with the experimental and nominal (up-scaled) values, available in the literature. Although the flow was considered as steady, a satisfactory correlation between numerical and experimental results was achieved. The comparison between results also showed, the significance of selection, regarding the complexity and geometry of the analyzed wind turbine blade, the most appropriate numerical approach for computation of aerodynamic performances.

scholarly journals 3D Numerical Study of the Impact of Macro-Roughnesses on a Tidal Turbine, on Its Performance and Hydrodynamic Wake

2021 ◽  
Vol 9 (11) ◽  
pp. 1288
Author(s):  
Ilan Robin ◽  
Anne-Claire Bennis ◽  
Jean-Claude Dauvin
Keyword(s):  
Numerical Study ◽  
Pressure Coefficient ◽  
Turbulence Models ◽  
Numerical Approach ◽  
Turbine Rotor ◽  
Power Coefficient ◽  
Energetic Efficiency ◽  
Tidal Turbines ◽  
Tidal Turbine ◽  
The Impact

Biofouling is an important factor to consider when calculating the energetic efficiency of tidal farms. Despite the fact that biofouling effects have been widely investigated in the past for naval applications, very few studies concern tidal turbines. This paper proposes a numerical approach to assess the impact of biofouling on tidal turbines, which is efficient for testing many configurations. Two turbulence models are tested (RANS k-ω SST and LES Smagorinsky) for the motionless blade case to validate them. Then we chose to use the Smagorinsky model for the case of a complete tidal turbine rotor with realistically fouled blades. The pressure coefficient is strongly affected by the barnacle in the motionless blade case and the power coefficient is slightly degraded in the complete rotor case. Motionless blade cases do not represent the real biofouling behaviour for two reasons. First, sessile species settle in the down flow part of the chord where their impact is less important. Then, the surrounding turbulence provoked by the blades rotation in the rotor case reduces the impact of biofouling. In the wake, biofouling generates small vortexes that propagate into the larger ones, causing them to spread their energy.

Analysis of Blunt Trailing Edge Airfoils

2003 ◽  
Author(s):  
K. J. Standish ◽  
C. P. van Dam
Keyword(s):  
Experimental Data ◽  
Wind Turbine ◽  
Turbine Blades ◽  
Navier Stokes ◽  
Computational Techniques ◽  
Wind Turbine Blades ◽  
Trailing Edge ◽  
Blunt Trailing Edge ◽  
Large Wind ◽  
Structural Volume

The adoption of blunt trailing edge airfoils for the inner regions of large wind turbine blades has been proposed. Blunt trailing edge airfoils would not only provide increased structural volume, but have also been found to improve the lift characteristics of airfoils and therefore allow for section shapes with a greater maximum thickness. Limited experimental data makes it difficult for wind turbine designers to consider and conduct tradeoff studies using these section shapes. This lack of experimental data precipitated the present analysis of blunt trailing edge airfoils using computational fluid dynamics. Several computational techniques are applied including a viscous/inviscid interaction method and several Reynolds-averaged Navier-Stokes methods.

scholarly journals Estimation of wind turbine blade aerodynamic performances computed using different numerical approaches

2018 ◽  
Vol 45 (1) ◽  
pp. 53-65 ◽  
Author(s):  
Jelena Svorcan ◽  
Ognjen Pekovic ◽  
Toni Ivanov
Keyword(s):  
Wind Turbine ◽  
Thrust Force ◽  
Turbulence Models ◽  
Turbine Rotor ◽  
Momentum Balance ◽  
Horizontal Axis Wind Turbine ◽  
Ansys Fluent ◽  
Force Coefficients ◽  
Aerodynamic Performances ◽  
Numerical Approaches

Although much employed, wind energy systems still present an open, contemporary topic of many research studies. Special attention is given to precise aerodynamic modeling performed in the beginning since overall wind turbine performances directly depend on blade aerodynamic performances. Several models different in complexity and computational requirements are still widely used. Most common numerical approaches include: i) momentum balance models, ii) potential flow methods and iii) full computational fluid dynamics solutions. Short explanations, reviews and comparison of the existing computational concepts are presented in the paper. Simpler models are described and implemented while numerous numerical investigations of isolated horizontal-axis wind turbine rotor consisting of three blades have also been performed in ANSYS FLUENT 16.2. Flow field is modeled by Reynolds Averaged Navier-Stokes (RANS) equations closed by two different turbulence models. Results including global parameters such as thrust and power coefficients as well as local distributions along the blade obtained by different models are compared to available experimental data. Presented results include fluid flow visualizations in the form of velocity contours, sectional pressure distributions and values of power and thrust force coefficients for a range of operational regimes. Although obtained numerical results vary in accuracy, all presented numerical settings seem to slightly under- or over-estimate the global wind turbine parameters (power and thrust force coefficients). Turbulence can greatly affect the wind turbine aerodynamics and should be modeled with care.

scholarly journals Design Optimization of a Multi-Megawatt Wind Turbine Blade with the NPU-MWA Airfoil Family

Energies ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 3330 ◽  
Author(s):  
Jianhua Xu ◽  
Zhonghua Han ◽  
Xiaochao Yan ◽  
Wenping Song
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Weight Reduction ◽  
Stokes Equations ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Aerodynamic Performance ◽  
Wind Turbine Blade ◽  
Structural Performance ◽  
Power Coefficient

A new airfoil family, called NPU-MWA (Northwestern Polytechnical University Multi-megawatt Wind-turbine A-series) airfoils, was designed to improve both aerodynamic and structural performance, with the outboard airfoils being designed at high design lift coefficient and high Reynolds number, and the inboard airfoils being designed as flat-back airfoils. This article aims to design a multi-megawatt wind turbine blade in order to demonstrate the advantages of the NPU-MWA airfoils in improving wind energy capturing and structural weight reduction. The distributions of chord length and twist angle for a 5 MW wind turbine blade are optimized by a Kriging surrogate model-based optimizer, with aerodynamic performance being evaluated by blade element-momentum theory. The Reynolds-averaged Navier–Stokes equations solver was used to validate the improvement in aerodynamic performance. Results show that compared with an existing NREL (National Renewable Energy Laboratory) 5 MW blade, the maximum power coefficient of the optimized NPU 5 MW blade is larger, and the chord lengths at all span-wise sections are dramatically smaller, resulting in a significant structural weight reduction (9%). It is shown that the NPU-MWA airfoils feature excellent aerodynamic and structural performance for the design of multi-megawatt wind turbine blades.

A Review of Wind Turbine Polar Data and its Effect on Fatigue Loads Simulation Accuracy

2015 ◽  
Author(s):  
Matthew Lennie ◽  
Georgios Pechlivanoglou ◽  
David Marten ◽  
Christian Navid Nayeri ◽  
Oliver Paschereit
Keyword(s):  
Wind Turbine ◽  
Turbine Blades ◽  
Turbulence Models ◽  
Leading Edge ◽  
Sensitivity Study ◽  
Wind Turbine Blades ◽  
Simulation Code ◽  
Simulation Accuracy ◽  
Inflow Turbulence ◽  
Lift And Drag

To certify a Wind Turbine the standard processes set out by the GL guidelines and the IEC61400 demand a large number of simulations in order to justify the safe operation of the machine in all reasonably probable scenarios. The result of this rather demanding process is that the simulations rely on lower fidelity methods such as the Blade Element Momentum (BEM) method. The BEM method relies on a number of simplified inputs including the coefficient of lift and drag polar data (usually referred to as polars). These polars are usually either measured experimentally, generated using tools such as XFoil or, in some cases obtained using 2D CFD. It is typical to then modify these polars in order to make them suitable for aeroelastic simulations. Some of these modifications include 360° angle of attack extrapolation methods and polar modifications to account for 3D effects. Many of these modifications can be perceived to be a black art due to the manual selection of coefficients. The polars can misrepresent reality for many reasons, for example, inflow turbulence can affect measurements obtained in wind tunnels. Furthermore, on real wind turbine blades leading edge erosion can reduce performance. Simulated polars can even vary significantly due to the choice of turbulence models. Stack these effects on top of the uncertainties caused by yaw error, pitch error and dynamic stall and one can clearly see an operating environment hostile to accurate simulations. Colloquial evidence suggests that experienced designers would account for all of these sources of errors methodically, however, this is not reflected by the certification process. A review of experimental data and literature was performed to identify some of the inaccuracies in wind turbine polars. Significant variations were found between a range of 2D polar techniques and wind tunnel measurements. A sensitivity study was conducted using the aeroelastic simulation code FAST (National Renewable Energy Laboratory) with lift and drag polars sourced using different methods. The results were post-processed to give comparisons the rotor blade fatigue damage; variations in accumulated damages reached levels of 164%. This variation is not disastrous but is certainly enough to motivate a new approach for certifying the aerodynamic performance of wind turbines. Such an approach would simply see the source of polar data and all post-processing steps documented and included in the checks performed by certification bodies.

scholarly journals Effect of Rotor Spacing and Duct Diffusion Angle on the Aerodynamic Performances of a Counter-Rotating Ducted Fan in Hover Mode

Processes ◽  
2020 ◽  
Vol 8 (11) ◽  
pp. 1338
Author(s):  
Woo-Yul Kim ◽  
Santhosh Senguttuvan ◽  
Sung-Min Kim
Keyword(s):  
Steady State ◽  
Numerical Model ◽  
Figure Of Merit ◽  
Aerodynamic Performance ◽  
Power Coefficient ◽  
Flow Conditions ◽  
Thrust Coefficient ◽  
Ducted Fan ◽  
Aerodynamic Performances ◽  
Rotor Model

The aerodynamic performance of a counter-rotating ducted fan in hover mode is numerically analyzed for different rotor spacings and duct diffusion angles. The design of the counter-rotating fan is inspired by a custom-designed single rotor ducted fan used in a previous study. The numerical model to predict the aerodynamic performance of the counter-rotating ducted fan is developed by adopting the frozen rotor approach for steady-state incompressible flow conditions. The relative angle between the front and the rear rotor is examined due to the usage of the frozen rotor model. The results show that the variation of thrust for the different relative angles is extremely low. The aerodynamic performances are evaluated by comparing the thrust, thrust coefficient, power coefficient, and figure of merit (FOM). The thrust, thrust coefficient, and FOM slightly increase with increasing rotor spacing up to 200 mm, regardless of the duct diffusion angle, and reduce on further increase in the rotor spacing. The duct diffusion angle of 0° generates about 9% higher thrust and increases the FOM by 6.7%, compared with the 6° duct diffusion angle. The duct diffusion angle is highly effective in improving the thrust and FOM of the counter-rotating ducted fan, rather than the rotor spacing.

scholarly journals Investigation of an Innovative Rotor Modification for a Small-Scale Horizontal Axis Wind Turbine

Energies ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2649 ◽  
Author(s):  
Artur Bugała ◽  
Olga Roszyk
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Cfd Simulation ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Airflow Distribution

This paper presents the results of the computational fluid dynamics (CFD) simulation of the airflow for a 300 W horizontal axis wind turbine, using additional structural elements which modify the original shape of the rotor in the form of multi-shaped bowls which change the airflow distribution. A three-dimensional CAD model of the tested wind turbine was presented, with three variants subjected to simulation: a basic wind turbine without the element that modifies the airflow distribution, a turbine with a plano-convex bowl, and a turbine with a centrally convex bowl, with the hyperbolic disappearance of convexity as the radius of the rotor increases. The momentary value of wind speed, recorded at measuring points located in the plane of wind turbine blades, demonstrated an increase when compared to the base model by 35% for the wind turbine with the plano-convex bowl, for the wind speed of 5 m/s, and 31.3% and 49% for the higher approaching wind speed, for the plano-convex bowl and centrally convex bowl, respectively. The centrally convex bowl seems to be more appropriate for higher approaching wind speeds. An increase in wind turbine efficiency, described by the power coefficient, for solutions with aerodynamic bowls was observed.

Wind Flow Over a Complex Terrain in Nygårdsfjell, Norway

2015 ◽  
Author(s):  
Muhammad Bilal ◽  
Narendran Sridhar ◽  
Guillermo Araya ◽  
Sivapathas Parameswaran ◽  
Yngve Birkelund
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Complex Terrain ◽  
Wind Farm ◽  
Turbulence Models ◽  
Future Research ◽  
Wind Flow ◽  
Governing Equations ◽  
The North ◽  
Numerical Predictions

The understanding of atmospheric flows is crucial in the analysis of dispersion of a contaminant or pollutant, wind energy and air-quality assessment to name a few. Additionally, the effects of complex terrain and associated orographic forcing are crucial in wind energy production. Furthermore, the use of the Reynolds-averaged Navier-Stokes (RANS) equations in the analysis of complex terrain is still considered the “workhorse” since millions of mesh points are required to accurately capture the details of the surface. On the other hand, solving the same problem by means of the instantaneous governing equations of the flow (i.e., in a suite of DNS or LES) would imply almost prohibitive computational resources. In this study, numerical predictions of atmospheric boundary layers are performed over a complex topography located in Nygårdsfjell, Norway. The Nygårdsfjell wind farm is located in a valley at approximately 420 meters above sea level surrounded by mountains in the north and south near the Swedish border. Majority of the winds are believed to be originated from Torneträsk lake in the east which is covered with ice during the winter time. The air closest to the surface on surrounding mountains gets colder and denser. The air then slides down the hill and accumulates over the lake. Later, the air spills out westward towards Ofotfjord through the broader channel that directs and transforms it into highly accelerated winds. Consequently, one of the objectives of the present article is to study the influence of local terrain on shaping these winds over the wind farm. It is worth mentioning that we are not considering any wind turbine model in the present investigation, being the main purpose to understand the influence of the local surface topography and roughness on the wind flow. Nevertheless, future research will include modeling the presence of a wind turbine and will be published elsewhere. The governing equations of the flow are solved by using a RANS approach and by considering three different two-equation turbulence models: k-omega (k–ω), k-epsilon (k–ε) and shear stress transport (SST). Furthermore, the real topographical characteristics of the terrain have been modeled by extracting the required area from the larger digital elevation model (DEM) spanning over 100 km square. The geometry is then extruded using Rhino and meshed in ANSYS Fluent. The terrain dimensions are approximately 2000×1000 meter square.

New Insight Into the Flow Around a Wind Turbine Airfoil Section1

2005 ◽  
Vol 127 (2) ◽  
pp. 214-222 ◽  
Author(s):  
F. Bertagnolio ◽  
N. N. Sørensen ◽  
F. Rasmussen
Keyword(s):  
Wind Turbine ◽  
Numerical Models ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Turbulence Models ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Pitching Airfoil ◽  
Wind Turbine Airfoil

The objective of this paper is an improved understanding of the physics of the aeroelastic motion of wind turbine blades in order to improve the numerical models used for their design. Two- and three-dimensional Navier–Stokes calculations of the flow around a wind turbine airfoil using the k−ω SST and Detached Eddy Simulation (DES) turbulence models, as well as an engineering semiempirical dynamic stall model, are conducted. The computational results are compared to the experimental results that are available for both the static airfoil and the pitching airfoil. It is shown that the Navier–Stokes simulations can reproduce the main characteristic features of the flow. The DES model seems to be able to reproduce most of the details of the unsteady aerodynamics. Aerodynamic work computations indicate that a plunging motion of the airfoil can become unstable.

scholarly journals Effect of Concentrator, Blade Diameter and Blade Number on the Savonius Wind Turbine Performance

2017 ◽  
Vol 5 (2) ◽  
Author(s):  
Ida Bagus Alit ◽  
Rudy Sutanto ◽  
I Made Mara ◽  
Mirmanto Mirmanto
Keyword(s):  
Wind Turbine ◽  
Concentration Ratio ◽  
Turbine Blades ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Wind Speeds ◽  
Vertical Axis Wind Turbines ◽  
Negative Moment ◽  
Low Efficiency ◽  
Low Wind Speeds

Savonius turbine is a type of vertical-axis wind turbines. The turbine has a potential to be developed as it has a simple construction and is suitable for low wind speeds. However, the turbine is still rarely used because of the low efficiency of the turbine compared to other turbines. The low efficiency of the turbine is due to the negative moment. Some efforts have been done to reduce the negative moment such as by adding a wind concentrator. The wind concentrator can steer the incoming wind toward the turbine blades that generate positive moments, consequently, the generated power increases. The aim of this research is to determine the effect of the number and diameter of the Savonius blade wind turbine with an additional concentrator. The concentrator had a concentration ratio of 6:1 and it was tested at the lower wind speeds of 2-5 m/s. The result shows that adding a wind concentrator can increase the rotational speed of the rotor, power coefficient, and the turbine power. The Savonius turbine with two blades has the best performance compared to the three and four blades. The Savonius blade wind turbine with the rotor diameter of 12 cm is the best Savonius turbine for the concentration ratio of 6:1.

Sign in / Sign up

Export Citation Format

Share Document