scholarly journals PENGGUNAAN SERBUK BATU TABAS SEBAGAI PENGGANTI SEBAGIAN SEMEN DALAM PEMBUATAN BETON

2013 ◽  
Author(s):  
I W. Intara ◽  
I M. Alit K. Salain ◽  
N. M. Anom Wiryasa
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Portland Cement ◽  
Cement Composite ◽  
Cementitious Material ◽  
Crushed Stone ◽  
Partial Replacement ◽  
Maximum Diameter ◽  
Fine Aggregate

Research on the use of stone dust (SDT) as a partial replacement of Ordinary Portland Cement (OPC) has been carried out by using cylindrical concrete specimens with Ø = 150 mm and h = 300 mm. Specimens were made by using the ratio, in weight, of cementitious material : sand : crushed stone of 1.00 : 1.93 : 2.67. The water cementitious material ratio is of 0.52. The cementitious material is a mixture of OPC and SDT. The percentage of OPC replacement by SDT varied from 0%-25%. The distribution of grains of sand and crushed stone are designed according to SNI 03-2384-2000: gradation zone 2 for fine aggregate and gradation with a maximum diameter of 20 mm for coarse aggregate. The tests of compressive strength, elastic modulus, tensile strength and permeability on the cylindrical specimens were realized at 28 and 56 days. The result indicates that SDT shows a good pozzolanic reactivity in terms of compressive strength, elastic modulus, tensile strength and permeability. Therefore, it can be used as a component of Portland Cement Composite. The development of compressive strength, elastic modulus, tensile strength and permeability of concrete produced with a mixture of OPC and SDT depends on the amount of SDT used in the mixture and hydration time. The pozzolanic effect of SDT can only be seen at the age of 56 days. The optimal use of SDT as a partial replacement of OPC in concrete applications varied from 5%-10%.

scholarly journals Mechanical Behaviour on Replacement of Aggregate by E-waste in Concrete

2019 ◽  
Vol 9 (2) ◽  
pp. 302-305 ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Mechanical Behaviour ◽  
Coarse Aggregate ◽  
Environmental Problems ◽  
Waste Utilization ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Construction Work ◽  
Split Tensile Strength

Concrete is a widely used material in all construction work. The aim of the project is to study the behavior of concrete with replacement of E waste. The fine aggregate and coarse aggregate are naturally available due to increase in demand it is over exploited. The waste utilization is sustainable solution to environmental problems Waste from electric and electronic equipment is used as an E waste replacement for coarse aggregate in concrete which is used in the construction .Therefore the effects have been made to study the use of E waste components as a partial replacement of coarse aggregate in 5%, 10% and 15%. To determine the optimum percentage of E waste that can be replaced for coarse aggregate the compressive strength and split tensile strength of concrete to be studied. After determining the optimum percentage of E waste that can be replaced with coarse aggregate. The comparison of the conventional and optimum percentage of E waste replaced with concrete has been done

scholarly journals Study on Mechanical Properties of PET Fiber-Reinforced Coal Gangue Fine Aggregate Concrete

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Yanlin Huang ◽  
An Zhou
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Plain Concrete ◽  
Coal Gangue ◽  
Fine Aggregate ◽  
Replacement Rate ◽  
River Sand ◽  
Aggregate Concrete

In recent years, with the rapid development of the construction industry, the demand for natural river sand has become increasingly prominent. Development of alternatives to river sand has become an interesting direction for concrete research. In this paper, coal gangue was proposed to replace part of the river sand to produce coal gangue fine aggregate concrete, while waste polyethene terephthalate (PET) bottles were used as raw materials to make PET fibers to improve the mechanical properties of coal gangue fine aggregate concrete. There were two parts of the test conducted. In the first part, the compressive strength of the gangue fine aggregate concrete cube, splitting tensile strength, axial compressive strength, and static elastic modulus were studied when the substitution rate of coal gangue increased from 0% to 50%. Referring to the equation of the full stress-strain curve of plain concrete, the stress-strain constitutive equation of coal gangue fine aggregate concrete was analyzed and studied. By comparing with plain concrete, it was found that the coal gangue concrete with a replacement rate of 50% had higher compressive strength and tensile strength, but its brittleness was significantly greater than that of plain concrete in the later stage. In the second part, by studying the effect of different PET fiber content on the mechanical properties of coal gangue fine aggregate concrete with a replacement rate of 50%, it was found that when the addition of PET fiber was 0.1% and 0.3%, not only were compressive strength, splitting tensile strength, static elastic modulus, and flexural strength of the gangue fine aggregate concrete effectively improved but also the brittleness of concrete can be significantly reduced. The study found that after adding 0.3% PET fiber, the coal gangue fine aggregate concrete with a replacement rate of 50% has better mechanical properties and less brittleness.

scholarly journals An Experimental Research On Partial Replacement Of Coarse Aggregate with Recycled Aggregate and Fine Aggregate with Granite Powder

2019 ◽  
Vol 8 (9S2) ◽  
pp. 72-77
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Age Group ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
Granite Powder

Now a days increase in population increases the demand of concrete for construction purpose and Aggregates are the important constituents in concrete.Re-use of demoliation waste avoids the problem of waste disposal and is also helpful in reducing the gap between demand and supply of fresh aggregates. This research deals with partial replacement of natural coarse aggregates (NCA) with recycled coarse aggregates (RCA) of age group 30 years and 35 years in different proportions like 20%, 30%, 40% . For this, M20 grade of concrete is adopted. Curing of specimens were done for 7days and 28 days to attain the maximum strengths. Partial replacement of fine aggregate with Granite powder at 5%, 10%, 15% were done to reduce the waste percentage as well to gain more strength. After casting the specimens of RCA with Granite powder replacement, curing was done and the specimens were tested for compressive and tensile strengths. Obtained results of compressive and tensile strengths of RCA concrete mix were compared with conventional concrete. In this direction, an experimental investigation of compressive and tensile strength was undertaken to use RCA as a partial replacement in concrete. It was observed that the concrete with recycled aggregates of 30years and 35years age group achieved maximum compressive strength of 29.03 N/mm2 , 28.96 N/mm2 and tensile strength of 11.91 N/mm2 , 10.34 N/mm2 were obtained at 40%replacement of RCA respectively. It is found that the compressive strength and Split tensile strength of RAC with copper slag was increased 8.20% and 2.90% when compared with the RAC.

scholarly journals Effects of Partial Replacement of Fine Aggregate with Quarry Dust on Concrete Properties

2020 ◽  
Vol 4 (1) ◽  
Author(s):  
S.O Ajamu ◽  
I.A Raheem ◽  
S.B Attah ◽  
J.O Onicha
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Replacement Level ◽  
River Sand ◽  
Split Tensile Strength ◽  
Stone Dust ◽  
Concrete Production ◽  
Quarry Dust

Natural river sand is one of the important constituent materials in concrete production while stone dust is a material obtained from crusher plants which is also sometimes being used either partially or fully in replacement of natural river sand in concrete production. Use of stone dust in concrete not only improves the quality of concrete but also conserve the natural river sand. However, due its scarcity and environmental degradation caused resulting from excessive mining of Natural river sand, there is need to investigate an alternative material of the same quality which can replace river sand in concrete production. In the present study, experiments were carried out to study the gradation of aggregates, workability, compressive strength and split tensile strength of concrete made using quarry dust as replacement of fine aggregate at 0, 25, 50, 75, and 100%. Grade M15 of concrete was produced with ordinary Portland cement (OPC) for referral concrete while M25 of concrete was prepared for compressive strength and split tensile strength concrete. Workability and Compressive strength were determined at different replacement level of fine aggregate and optimum replacement level was determined based on compressive strength. Results showed that by replacing 50% of fine aggregate with quarry dust, concrete of maximum compressive strength can be produced as compared to all other replacement levels. The effect of quarry dust on compressive strength and split tensile strength was investigated and from the overall result obtained, it was observed that the compressive strength and split tensile strength increased significantly for all the curing ages from 0% to 50% replacement level of quarry dust. Maximum value obtained for 28day compressive and tensile strength were 25N/mm2 and 2.3N/mm2 respectively and this occurred at 50% replacement.

The Development of Slurry Seal Design with Ordinary Portland Cement Replacement by Low Calcium Fly Ash

2015 ◽  
Vol 776 ◽  
pp. 24-29 ◽  
Author(s):  
Ary Setyawan ◽  
D. Sarwono ◽  
M.S. Adnan
Keyword(s):  
Tensile Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Indirect Tensile Strength ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Low Calcium ◽  
Indirect Tensile ◽  
Slurry Seal

Slurry Seal is an impermeable non-structural thin layer that is used for pavement maintenance consisting of a cold laid mixture of asphalt emulsion with continuous graded fine aggregate, mineral filler, water and other added ingredients. Ordinary Portland Cement (OPC) as the main filler in the application of slurry seal. Due to the relatively high cement prices and the pollution control for the environment; it is required to maintain the quality of the slurry by using a combination of OPC and LCFA (Low Calcium Fly Ash). This research was conducted to determine the value of consistency, setting time and indirect tensile strength (ITS) of slurry seal containing LCFA. A consistency testing used to obtain optimum moisture content to produce the sample for the rest of the test. The results show that with the addition of 5% water for pre-wetting and subsequently 10% of water content, the mixture provide appropriate consistency as required by highways standard. The time settings also meet the requirements of highways standard between 15 to 720 minutes for all types of mixtures. The mixture with composition of 50% OPC and 50% LCFA is considered as an ideal mixture at the optimum density value of 1.769 g/cm3, porosity of 9.55% and the indirect tensile strength of 30.99 kPa. It could be concluded that fly ash can be used as OPC partial replacement and enhance the properties on slurry seal application.

scholarly journals The Effect on Strength of Concrete by Partial Replacement of Cement and Fine Aggregate with Flyash, Granite Powder and Plastic Fibres

2019 ◽  
Vol 8 (4) ◽  
pp. 3516-3519
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Power Plants ◽  
Thermal Power ◽  
Raw Material ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Normal Concrete ◽  
Split Tensile Strength ◽  
Granite Powder

The rapid growth of the population leads to a requirement of infrastructure this leads to scarcity of raw material for construction such as cement and sand. The other hand pollution growing due to thermal power plants, granite polishing unit and plastic waste this need to be removed. This gives an idea of using this compound as a raw material in concrete making. This concept found to effective minimizes disposal of fly, granite power and plastic wastes, and leads towards Green Building Concepts. In this investigation of M25 grade normal concrete is made by cement, sand, and aggregate which is tested and compared by special concrete. The concrete mix is prepared as per 10262 -2019 by adding replacing small amount of Fly ash in place of cement OPC 53 grade, and fine aggregate is prepared by partial replacing with granite powder (0%,10%,20%,30%)and another mix is prepared by adding 0.5 nylon fiber, partial replacement of fine aggregate with granite powder (0%,10%,20%,30%)specimens are casted . The casted specimens are tested for split tensile strength and compressive strength 7, 14 and 28 day’s respectively and these results also compared with each other. I t is observed that compressive strength and split tensile of concrete at 28days of curing show max value when compared with normal concrete. When the percentage of granite powder increases to 30% it shows that a decrease in both split tensile strength of concrete and compressive strength. When we added fiber to the concrete there is an increase in compressive strength and split tensile strength but there is a not much increase in compressive strength but increase in split tensile strength

scholarly journals Partial Replacement of Sand by Crusher Dust and Mild Steel Scrap in Concrete

2021 ◽  
Vol 9 (8) ◽  
pp. 1013-1020
Author(s):  
Diksha Jain
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Mild Steel ◽  
Construction Materials ◽  
Copper Slag ◽  
Partial Replacement ◽  
Steel Scrap ◽  
Fine Aggregate ◽  
Building Engineering

Abstract: This research focuses on studying the effect of Mild Steel Scrap and Crusher Dust on the Properties of Concrete Mixes as a partial replacement of Sand. The trend of mixing several kinds of additional materials such as Glass powder, plastic, Quarry dust, Copper slag, Steel scrap, in building engineering is now growing. Consumption of Crusher dust and Mild steel scrap are one of the lively research area that include the effectiveness of replacement in all the aspects of construction materials. It is very significant to develop eco-friendly concrete from ceramic waste. This Research deals with the experimental study on the mechanical strength properties of M20 grade concrete with the partial replacement of fine aggregate by using crusher dust and mild Steel Scrap. In order to analyze the mechanical properties such as Compressive Strength, Spilt tensile strength, and Workability the samples were casted with mild steel scrap having constant proportion of 5% and crusher dust having 10%, 15% ,20% 25%, 30%, 35%, 40% partial replacement. In second category sand has been partially replaced by mild steel scrap proportion of 10%, 15%, 20%, 25%, 30%, 35% and crusher dust by 20%, 25%, 30% 35% at a different periods of curing 7 days, and 28 days. The optimal of percentage addition of Crusher dust and Mild steel scrap are analyzed considering the needs of mechanical properties of concrete. Keywords: Crusher Dust, Mild Steel Scrap, Compressive Strength, Spilt tensile Strength, Mechanical properties,

scholarly journals Mechanical Behavior of Recycled Fine Aggregate Concrete with High Slump Property in Normal- and High-Strength

2019 ◽  
Vol 13 (1) ◽  
Author(s):  
Minkwan Ju ◽  
Kyoungsoo Park ◽  
Won-Jun Park
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Mechanical Behavior ◽  
High Strength ◽  
Strength Development ◽  
Fine Aggregate ◽  
Structural Concrete ◽  
Aggregate Concrete ◽  
Model Code

AbstractThis study investigated the mechanical behavior of normal strength (NS) and high strength (HS) concrete containing recycled fine aggregates (RFAs). A high slump mixing design was employed, which may be potentially used as filled structural concrete. The compressive strength, tensile strength, and elastic modulus were measured according to the RFA replacement ratio and curing time. In addition, the shrinkage strain was measured in a temperature and humidity chamber over 260 days. The compressive strength and elastic modulus of RFA concrete were approximately 70–90% of those of virgin concrete. The decreases in the compressive strength and elastic modulus for NS concrete were larger than those for HS concrete. This could be explained by the difference in failure mechanism between NS and HS concrete. The average ratio of the compressive strength at 190 days to that at 28 days was 1.15–1.3, and the ratio of the tensile strength at 190 days to that at 28 days was 1.15–1.25. These demonstrate good strength development. The ratios between the elastic modulus and compressive strength for RFA concrete were dissimilar to those for virgin concrete but similar to those for recycled coarse aggregate concrete. ACI 318-14 (Building code requirements for structural concrete and commentary, 2014) and Model Code (Fib model code for concrete structures, 2010) overestimated the elastic modulus of RFA concrete. Therefore, this study suggested an empirical expression to approximate the elastic modulus of RFA concrete. The increase in shrinkage owing to the use of RFA was at most 5–6% of the ultimate compressive strain of concrete.

Carbonation Resistance of Fine Aggregate Concrete with Partial Replacement of Cement

2016 ◽  
Vol 722 ◽  
pp. 201-206 ◽  
Author(s):  
Tereza Pavlů ◽  
Magdaléna Šefflová
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Main Topic ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Aggregate Concrete ◽  
Durability Properties ◽  
Waste Concrete ◽  
Carbonation Resistance ◽  
Strength In Bending

The main aim of this contribution is verification of durability properties of concrete with partial replacement of cement by recycled cement powder (RCP) sourced from pure waste concrete. The main topic of this article is the study of influence of partial replacement of cement by RCP to the carbonation resistance of fine aggregate concrete with partial replacement of cement. The compressive strength, tensile strength in bending and depth of carbonation were tested after 56 days of CO2 curing. Partial replacement of cement was 0, 5, 10 and 15 % for all these tests. The properties were investigated by using prismatic specimens.

scholarly journals Eucalyptus Chip Ashes in Cementitious Composites

2014 ◽  
Vol 775-776 ◽  
pp. 205-209 ◽  
Author(s):  
Domingos Sávio de Resende ◽  
Herbet Radispiel Filho ◽  
José Genário Keles ◽  
Augusto Cesar da Silva Bezerra ◽  
Maria Teresa Paulino Aguilar ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Portland Cement ◽  
Mechanical Behavior ◽  
Minas Gerais ◽  
The State ◽  
Pozzolanic Activity ◽  
Partial Replacement ◽  
Cementitious Composites ◽  
Mineral Additives

The Alto Paranaiba and Triângulo Mineiro mesoregion in the state of Minas Gerais and the State of São Paulo have a number of industries with eucalyptus chip fired boilers that produce great amounts of ash. Since thermoelectric ashes generally have good pozzolanic activity, this paper studied the mechanical behavior of cementitious composites made with raw eucalyptus chip ash as a partial replacement for Portland cement and processed under two different conditions. The mechanical behavior of the composites was measured from tests on specimens for their compressive strength, tensile strength to diametral stress and to bending. Results show ashes could be used as mineral additives.

Sign in / Sign up

Export Citation Format

Share Document