scholarly journals Improving Some Mechanical Properties and Thermal conductivity of PMMA Polymer by using Environmental Waste

2021 ◽  
pp. 2188-2196
Author(s):  
Tagreed M. Al-Saadi ◽  
Anaam W. Watan ◽  
Hanaa G. Attiya
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Environmental Problem ◽  
Matrix Material ◽  
Weight Fraction ◽  
Reinforcement Rate ◽  
Mechanical And Thermal Properties ◽  
The Matrix ◽  
Pmma Polymer ◽  
Composite Samples

This study was achieved to satisfy two goals, the first of which is to treat an environmental problem represented by the disposal of date seeds, and the second is the use of these wastes to improve some mechanical and thermal properties of poly methyl methacrylate PMMA through strengthening different proportions of the powder of date seeds. Particles of date seeds were used as a natural strengthening material for PMMA polymer, by mixing the matrix material (resin) with the hardener while still stirring continuously for a period of 10 min. After that, the samples of the reinforced material were prepared by adding the powder of date seeds, which is the reinforcing substance, with different percentages of weight fraction (0, 0.5, 1, 2, 3, 5 wt. %) and a grain size of <75 µm, while continuing to stir (10 min) for a second time. The composite samples were prepared by the Hand-Lay-up method and cut according to the standard ASTM. Thermal conductivity and some mechanical properties, such as impact strength, tensile strength, compressive strength, flexural strength, and hardness, were studied. An improvement was found in all properties at the reinforcement rate of 1-2 wt. %.

scholarly journals The Effect Of Phoenix Dactylifera L. Pinnae Reinforcement On The Mechanical And Thermal Properties Of Polymer Composite

2019 ◽  
Vol 25 (104) ◽  
pp. 339-351
Author(s):  
Adil I. Khadim ◽  
Dhefaf H.Badrri ◽  
Zainab S. Abdul-Ridha
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Fiber Length ◽  
Matrix Material ◽  
Phoenix Dactylifera ◽  
Mechanical And Thermal Properties ◽  
Green Leaves ◽  
Phoenix Dactylifera L ◽  
The Impact ◽  
Composite Samples

Phoenix  dactylifera l. pinnae (the green leaves of dates palm) were used as natural reinforcing (strengthening) fibers to improve the mechanical properties of polyester as a matrix material, the fibers of the green leaves of dates palm were used in two lengths, 10 and 20mm with five rates of 0, 2.5, 5, 10, and 20% , where the reinforcing with the leaves fibers increases the hardness strength from 76.5 to be about 86.55, the Impact value raised from about 0.313 to 0.461, in addition to that the flexural strength from 2.66 to be about 55, and the thermal conductivity increases from 2.54 ????∕????.℃ to 5.41 ????∕????.℃. The results of the present search explains that the composite samples reinforced at rate 20% and 10mm fiber length gives the best results.

Impact Strength, Flexural Modulus and Wear Rate of PMMA Composites Reinforced by Eggshell Powders

2020 ◽  
Vol 38 (7A) ◽  
pp. 960-966
Author(s):  
Aseel M. Abdullah ◽  
Hussein Jaber ◽  
Hanaa A. Al-Kaisy
Keyword(s):  
Impact Strength ◽  
Wear Rate ◽  
Flexural Modulus ◽  
Matrix Material ◽  
Weight Fraction ◽  
Pure Pmma ◽  
Calcination Process ◽  
The Matrix ◽  
The Impact ◽  
Interface Bond

In the present study, the impact strength, flexural modulus, and wear rate of poly methyl methacrylate (PMMA) with eggshell powder (ESP) composites have been investigated. The PMMA used as a matrix material reinforced with ESP at two different states (including untreated eggshell powder (UTESP) and treated eggshell powder (TESP)). Both UTESP and TESP were mixed with PMMA at different weight fractions ranged from (1-5) wt.%. The results revealed that the mechanical properties of the PMMA/ESP composites were enhanced steadily with increasing eggshell contents. The samples with 5 wt.% of UTESP and TESP additions give the maximum values of impact strength, about twice the value of the pure PMMA sample. The calcination process of eggshells powders gives better properties of the PMMA samples compared with the UTESP at the same weight fraction due to improvements in the interface bond between the matrix and particles. The wear characteristics of the PMMA composites decrease by about 57% with increases the weight fraction of TESP up to 5 wt.%. The flexural modulus values are slightly enhanced by increasing of the ESP contents in the PMMA composites.

scholarly journals Improvement of mechanical properties of HfB2-based composites by incorporating in situ SiC reinforcement through pressureless sintering

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
S. Ghadami ◽  
E. Taheri-Nassaj ◽  
H. R. Baharvandi ◽  
F. Ghadami
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Relative Density ◽  
Pressureless Sintering ◽  
Sintering Process ◽  
Vacuum Atmosphere ◽  
Sic Reinforcement ◽  
Microstructural Studies ◽  
Composite Samples

AbstractHfB2, Si, and activated carbon powders were selected to fabricate 0–30 vol% SiC reinforced HfB2-based composite. Pressureless sintering process was performed at 2050 °C for 4 h under a vacuum atmosphere. Microstructural studies revealed that in situ SiC reinforcement was formed and distributed in the composite according to the following reaction: Si + C = SiC. A maximum relative density of 98% was measured for the 20 vol% SiC containing HfB2 composite. Mechanical investigations showed that the hardness and the fracture toughness of these composites were increased and reached up to 21.2 GPa for HfB2-30 vol% SiC and 4.9 MPa.m1/2 for HfB2-20 vol% SiC, respectively. Results showed that alpha-SiC reinforcements were created jagged, irregular, and elongated in shape which were in situ formed between HfB2 grains and filled the porosities. Formation of alpha-SiC contributed to improving the relative density and mechanical properties of the composite samples. By increasing SiC content, an enhanced trend of thermal conductivity was observed as well as a reduced trend for electrical conductivity.

Effect of peanut and walnut shells powders on tensile properties and morphological test by using heat cured PMMA as a matrix for prosthetic Denture

2021 ◽  
Vol 39 (2A) ◽  
pp. 196-205
Author(s):  
Zainab M. Abdul Monem ◽  
Jawad K. Oleiwi ◽  
Qahtan A. Hamad
Keyword(s):  
Fracture Surface ◽  
Surface Morphology ◽  
Matrix Material ◽  
Weight Fraction ◽  
Fracture Surface Morphology ◽  
Ductile Materials ◽  
Walnut Shells ◽  
Peanut Shells ◽  
The Matrix ◽  
Material Powder

In the current Research , the heat cured   matrix material powder of PMMA was reinforced with peanut and walnut shells (natural powders) which are chemically treated with 5% (w/v) (NaOH) to improve the matrix bonding (PMMA) before being used as a reinforcing powder and adding to exactly similar averages particle sizes ≤ (53µm), with different weight fractions of (4, 8, and 12 wt.%). The ASTM D638 is used for composite specimens of the tensile test. The results indicated that the Elastic modulus values reached its maximum value at (8 wt.%.) when reinforced with peanut shells particles (1.053Gpa) , while ,the values of tensile strength, elongation percentage at break, decrease as the weight fraction of peanut and walnut shells powder increase and the lowest values is obtained by reinforcing with peanut shells particles to reach their minimum values at (12 wt.%.) where the lowest values of them are (29 MPa, 2.758% ) respectively. The fracture surface morphology of pure PMMA seemed to be homogenous morphology in (SEM) test, whereas the fracture surface morphology of PMMA composite reinforced by (peanut and walnut shells) powders and shows a roughness fracture surface morphology this refer to semi ductile to ductile materials.

scholarly journals Microstructural analysis of Al6063/sic with calcium additives for hardness enhancement

2018 ◽  
Vol 225 ◽  
pp. 03007
Author(s):  
Balaji Bakthavatchalam ◽  
Khairul Habib ◽  
Namdev Patil ◽  
Omar A Hussein
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Matrix Material ◽  
Microstructural Analysis ◽  
Wear Loss ◽  
Alloying Element ◽  
Silicon Phase ◽  
High Durability ◽  
The Matrix ◽  
Al6063 Alloy

Microstructural Analysis plays an important role in enhancing the mechanical properties of metals and composites. Usually Aluminium Silicon Carbide (Al6063/SiC) alloys are mixed with strontium, sodium and antimony for high durability even though they are toxic and costly. As an alternative calcium is used as an alloying element to improve the mechanical property of Al6063/Sic alloy. In this paper Al6063 is chosen as the matrix material while Sic is used as a reinforcement where calcium powder is added to modify the silicon phase of the composite. Finally, concentration of Silicon carbide is varied from 0 to 150 mg to produce four specimens of Al6063 alloy and it is subjected to microstructure analysis which showed the reduction of grain size and therefore improvement in the hardness from 52.9 HV to 58.4 HV and decrease in the wear loss from 3.97 to 3.27 percentage.

scholarly journals Investigation of Effective Mechanical Characteristics of Nanomodified Carbon-Epoxide Composite by Numerical and Analytical Methods

2021 ◽  
Vol 12 (5) ◽  
pp. 535-541
Author(s):  
M.O. Kaptakov
Keyword(s):  
Mechanical Properties ◽  
Numerical Modeling ◽  
Fracture Surface ◽  
Mechanical Characteristics ◽  
Modeling Methods ◽  
Fullerene Soot ◽  
The Matrix ◽  
Numerical And Analytical Methods ◽  
Composite Samples

In this work, the mechanical properties of composite samples prepared using a conventional and nanomodified matrix were studied. The thickness of the monolayers in the samples was 0,2 μm. It was found in experiments, that the addition of fullerene soot as a nanomodifierled to an increase in the mechanical properties of the samples along the direction of reinforcement. At the same time, an improvement in the quality of the contact of the matrix with the fibers in the samples with the nanomodifier was observed: on the fracture surface, the nanomodified matrix envelops the fibers, while the usual matrix completely exfoliates. The obtained effects of changing the strength of composites can be associated, among other things, with a change in the level of residual stresses arising in composites during nanomodification. Analytical and numerical modeling methods are used to explain these effects.

scholarly journals Functional Application for the Corn Leaf Fibre to Make Reinforced Polymer Composites Sheet

2021 ◽  
Author(s):  
Ramratan Guru ◽  
Anupam Kumar ◽  
Rohit Kumar
Keyword(s):  
Volume Fraction ◽  
Agricultural Waste ◽  
Matrix Material ◽  
Research Work ◽  
Weight Fraction ◽  
Natural Fibre ◽  
Raw Material ◽  
Corn Husk ◽  
The Matrix ◽  
Composite Product

This research work has mainly utilized agricultural waste material to make a good-quality composite sheet product of the profitable, pollution free, economical better for farmer and industries. In this study, from corn leaf fibre to reinforced epoxy composite product has been utilized with minimum 35 to maximum range 55% but according to earlier studies, pulp composite material was used in minimum 10 to maximum 27%. Natural fibre-based composites are under intensive study due to their light weight, eco-friendly nature and unique properties. Due to the continuous supply, easy of handling, safety and biodegradability, natural fibre is considered as better alternative in replacing many structural and non-structural components. Corn leaf fibre pulp can be new source of raw material to the industries and can be potential replacement for the expensive and non-renewable synthetic fibre. Corn leaf fibre as the filler material and epoxy as the matrix material were used by changing reinforcement weight fraction. Composites were prepared using hand lay-up techniques by maintaining constant fibre and matrix volume fraction. The sample of the composites thus fabricated was subjected to tensile, impact test for finding the effect of corn husk in different concentrations.

Physical and Mechanical Properties of Composites with Aluminum Alloy Matrix Designed for Metal Forming

2013 ◽  
Vol 212 ◽  
pp. 59-62 ◽  
Author(s):  
Jerzy Myalski ◽  
Jakub Wieczorek ◽  
Adam Płachta
Keyword(s):  
Mechanical Properties ◽  
Metal Forming ◽  
Matrix Material ◽  
Physical And Mechanical Properties ◽  
Mechanical Mixing ◽  
Alloy Matrix ◽  
Segregation Process ◽  
The Matrix ◽  
Glass Carbon ◽  
Properties Of Composites

The change of matrix and usage of the aluminum alloys designed for the metal forming in making the composite suspension allows to extend the processing possibility of this type of materials. The possibility of the metal forming of the composites obtained by mechanical mixing will extend the range of composite materials usage. Applying of the metal forming e.g. matrix forging, embossing, pressing or rolling, will allow to remove the incoherence of the structure created while casting and removing casting failures. In order to avoid the appearance of the casting failures the homogenization conditions need to be changed. Inserting the particles into the matrix influences on the shortening of the composite solidification. The type of the applied particles influenced the sedimentation process and reinforcement agglomeration in the structure of the composite. Opposite to the composites reinforced with one-phase particles applying the fasess mixture (glassy carbon and silicon carbide) triggered significant limitation in the segregation process while casting solidification. Inserting the particles into the AW-AlCu2SiMn matrix lowers the mechanical properties tension and impact value strength. The most beneficial mechanical properties were gained in case of heterofasess composites reinforced with the particle mixture of SiC and glass carbon. The chemical composition of the matrix material (AW-AlCu2SiMn) allows to increase additionally mechanical characteristics by the precipitation hardening reached through heat casting forming.

The Effect of Surface Active Substances on the Mechanical Properties of a Copper-Matrix Nanocomposite

2019 ◽  
Vol 945 ◽  
pp. 493-497
Author(s):  
Y. Shchetinin ◽  
Y. Kopylov ◽  
A. Zhirkov
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Composite Material ◽  
Carbon Nanostructures ◽  
Hot Isostatic Pressing ◽  
Copper Matrix ◽  
Planetary Mill ◽  
Preliminary Treatment ◽  
Nanostructured Composite ◽  
The Matrix

The presented work reviews the research in the field of production of nanostructured composite materials based on copper, reinforced with carbon nanostructures. Particular attention is paid to the use of composites with high thermal conductivity as structural materials. The method of manufacturing a composite material based on copper is described in detail: modes of preliminary annealing, pre-pressing, hot isostatic pressing. The characteristics of the matrix and alloying components are given, and also preliminary treatment of copper powder and carbon nanotubes is described. Different mechanisms of component mixing are considered, the process of mechanical alloying in a planetary mill is described in detail, the results of measuring the thermal conductivity of samples are given. The mechanical characteristics of the samples are considered in detail: ultimate strength, yield strength, elongation. The degree of influence of surfactants on the uniformity of the distribution of alloying components and the mechanical properties of the composite material is determined.

Experimental investigation, modeling and optimization study on the mechanical properties of B4Cp/MWCNT/epoxy multi-scale hybrid composite

2020 ◽  
pp. 096739112097118
Author(s):  
Mustafa Taşyürek
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Process Parameters ◽  
Hybrid Composite ◽  
Optimization Method ◽  
High Rate ◽  
Dominant Factor ◽  
Mechanical And Thermal Properties ◽  
Multi Scale ◽  
The Matrix

In this study, process parameters and mechanical properties of the multi-scale composite were investigated experimentally and predictably. Multi-scale material includes boron carbide particles and multi walled carbon nanotubes (MWCNTs) in the epoxy-based matrix. Both reinforcements were reinforced into the matrix with various rates simultaneously. Average three tensile strength and hardness values were determined. The tensile strength and hardness were enhanced thanks to high rate of B4C usage up to 54.09% and 2.54%, respectively. The microstructure of the hybrid composite was investigated by Scanning Electron Microscopy. Also, Fourier Transform Infrared Spectroscopy was used to interpret spectral bands. The experimental data were analyzed using optimization method. Optimal process parameters for tensile strength and interfacial properties were determined. The Analysis of Variance (ANOVA) was used to obtain most significant factor and optimum levels of parameters. Finally, it was observed that B4C ratio is the most dominant factor affecting the mechanical and thermal properties.

Sign in / Sign up

Export Citation Format

Share Document