scholarly journals PENGARUH VARIASI DIAMETER MAKSIMUM AGREGAT DALAM CAMPURAN TERHADAP KEKUATAN TEKAN BETON

2019 ◽  
Vol 3 (1) ◽  
pp. 11-23
Author(s):  
Helwiyah Zain
Keyword(s):  
Compressive Strength ◽  
Maximum Diameter ◽  
Concrete Aggregate ◽  
Test Results ◽  
Natural Mineral ◽  
Size Selection ◽  
Concrete Mix ◽  
Compressive Strength Of Concrete ◽  
Average Compressive Strength

Aggregate is a natural mineral grains that serve as filler in concrete mix, and the greatest material contained in the concrete. These material influence on the properties of concrete, so that the diameter size selection is essential in making the concrete. This study aims to determine the effect of variations of aggregate maximum diameter to the compressive strength of concrete. In this study used 15 specimens, were divided into 3 groups witch each of 5 specimens. Each group is distinguished aggregate maximum diameter: 31.5 mm, 16 mm, and 8 mm. Specimens used in this study is the specimen cylinder with a diameter of 15 cm and 30 cm high. Speciment tested done at age of concrete 28 days. The average compressive strength of concrete for each group of test based on variations of  the aggregate maximum diameter is: for the aggregate maximum diameter of 31.5 mm = 249.67 kg / cm2; the aggregate maximum diameter 16 mm = 274.91 kg / cm2; and the aggregate maximum diameter of 8 mm = 326.74 kg / cm2. Based on these test results, show that the average compressive strength of the concrete for the aggregate maximum diameter of 16 mm is 10.11% stronger than the concrete with the aggregate maximum diameter of 31.5 mm; and the strength of concrete aggregate maximum diameter of 8 mm, 30.87% stronger than the concrete with aggregate maximum diameter of 31.5 mm.

scholarly journals TINJAUAN KUAT TEKAN BETON DENGAN MENGGUNAKAN SERAT BENDRAT SEBAGAI BAHAN TAMBAH

2019 ◽  
Vol 1 (2) ◽  
pp. 124-132
Author(s):  
Hermansyah ◽  
Moh Ihsan Sibgotuloh
Keyword(s):  
Compressive Strength ◽  
Fresh Concrete ◽  
Mix Design ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Fiber Concrete ◽  
Concrete Mix ◽  
Materials Used ◽  
Average Compressive Strength

The more widespread use of concrete construction and the increasing scale of construction, the higher the demand for materials used in concrete mixes. One of the innovations of concrete is fiber concrete. Hope the addition of fiber in concrete mixes such as wire fiber to increase the compressive strength value of normal concrete that is often used, so the purpose of this study is to determine the effect of adding wire fiber to the ease of working (workability) of the concrete mixture and to determine the effect of adding wire fiber to concrete compressive strength. In this study, the fiber used is the type of wire fiber with a diameter of 1 mm and a length of 60 mm. Fiber variations used are 0%, 0.4%, 0.6% and 0.8% based on the weight of fresh concrete. Concrete mix (mix design) using SNI 03-2834-2000 about concrete mix planning with a test life of 28 days. The test results showed that the lowest average compressive strength of 12,291 MPa occurred at 0% variation and the highest average compressive strength value of 20,656 MPa at 0.8% fiber variation. The increase is caused by the even distribution of fibers in the concrete produced, the higher the variation that is given by the fiber, the better the fiber spread, from these fibers provide a fairly good contribution to the fiber concrete

scholarly journals LIGHTWEIGHT CONCRETE MAKING ANALYSIS USING MIXED CELLULOSE

2019 ◽  
Vol 2 (2) ◽  
pp. 85-91
Author(s):  
Nanang Budi Setyawan ◽  
Fredy Kurniawan
Keyword(s):  
Compressive Strength ◽  
Experimental Method ◽  
Lightweight Concrete ◽  
Mix Design ◽  
Waste Paper ◽  
Test Results ◽  
Concrete Mix Design ◽  
Concrete Mix ◽  
Recycle Paper ◽  
Compressive Strength Of Concrete

Development era of globalization has resulted in increasing number of second-hand goods / waste that its existence can be a problem for life in the future. Many things are done in order to recycle paper cement in order to overcome this problem the existence of waste. One way is to use waste paper to be a part of the building. The purpose of this study, to determine the compressive strength and optimum density. Laboratory experimental method uses a variation of 10%, 20%, 30% and testing conducted in the form of compressive strength and density. From the test results obtained by the result of decrease in the compressive strength and density. In addition cellulose concrete mix design with variations determined that 10%, 20%, 30% resulted in a decrease in the compressive strength of concrete,

scholarly journals ANALISIS KUAT TEKAN BETON DENGAN AGREGAT PASIR DARI BOYOLALI MENGGUNAKAN BAHAN TAMBAH ABU SEKAM PEMBAKARAN KAYU DAN SERBUK HALUS ARANG BRIKET

Teknika ◽  
2018 ◽  
Vol 13 (2) ◽  
pp. 47
Author(s):  
Timbul Catur Suwiyono ◽  
Purwanto Purwanto ◽  
Anik Kustirini
Keyword(s):  
Compressive Strength ◽  
Fine Powder ◽  
Concrete Research ◽  
Test Results ◽  
Wood Burning ◽  
Compressive Strength Of Concrete ◽  
Concrete Testing ◽  
Average Compressive Strength

<p><em>Concrete research has been carried out, this study utilizes wood burning husk ash and fine powder of briquette charcoal as an added material from the weight of cement and sand used from Boyolali. This study aims to determine the compressive strength of concrete with materials added to wood burning husk ash and fine powder of briquette charcoal. Material variations added wood burning husk ash and briquette charcoal fine powder by 0%, 10%, 20% by weight of cement. This study used 0.5 fas and concrete testing at the age of 7 days, 14 days and 28 days. From the test results the average compressive strength of concrete at the age of 7 days with a material variation of 10% added was 15.05 MPA, and a material variation of 20% added was 13.47 MPA. Concrete at the age of 14 days with a material variation of 10% added is 15.76 MPA, and a material variation of 20% is 13.18 MPA. concrete at 28 days with a material variation of 10% added is 14.32 MPA, and a 20% added material variation is 14.32 MPA.</em></p><p><em> </em></p><p><strong><em>Keywords; </em></strong><em>wood burning husk ash, compressive strength, fine briquette charcoal powder</em></p><p><em> </em></p><p align="center"><strong>Abstrak</strong></p><p>Penelitian beton telah banyak dilakukan, penelitian ini memanfaatkan abu sekam pembakaran kayu dan serbuk halus arang <em>briket</em> sebagai bahan tambah dari berat semen dan pasir yang digunakan dari boyolali. Penelitian ini bertujuan untuk mengetahui kuat tekan beton dengan bahan tambah abu sekam pembakaran kayu dan serbuk halus arang <em>briket</em>. Variasi bahan tambah abu sekam pembakaran kayu dan serbuk halus arang <em>briket</em> sebesar 0%, 10%, 20% dari berat semen. Penelitian ini menggunakan fas 0,5 dan pengujian beton pada umur 7 hari, 14 hari dan 28 hari. Dari hasil pengujian kuat tekan rata-rata beton pada umur 7 hari dengan variasi bahan tambah 10% adalah 15,05 MPA, dan vari asi bahan tambah 20% adalah 13,47 MPA. Beton pada umur 14 hari dengan variasi bahan tambah 10% adalah 15,76 MPA, dan variasi bahan tambah 20% adalah 13,18 MPA. beton pada umur 28 hari dengan variasi bahan tambah 10% adalah 14,32 MPA, dan vari asi bahan tambah 20% adalah 14,32 MPA.</p><p><strong> </strong></p><p><strong>Kata kunci : </strong>abu sekam pembakaran kayu, kuat tekan, serbuk halus arang briket</p>

scholarly journals PENGARUH PERSENTASE PENAMBAHAN SIKA VISCOCRETE-10 TERHADAP KUAT TEKAN BETON

2019 ◽  
Vol 2 (1) ◽  
pp. 13-24
Author(s):  
Muhammad Zardi ◽  
Cut Rahmawati ◽  
T Khamarud Azman
Keyword(s):  
Compressive Strength ◽  
American Concrete Institute ◽  
Building Structure ◽  
Test Results ◽  
Normal Mixture ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Concrete Mix Design ◽  
Compressive Strength Of Concrete ◽  
Average Compressive Strength

Building structure often use concrete as the main structural material, in which the concrete-forming materials such as cement, sand, gravel, water and additives. The aim of study is to investigate the influence of addition of Sika Viscocrete-10 toward concrete compressive strength. Concrete is planned with Water Cement Ratio 0.3. Slump values obtained for normal concrete with maximum aggregate diameter of 25.4 mm is 7.8 cm. The values are in accordance with the slump plan of 7.5 to 10 cm, meanwhile values slump that use Sika Viscocrete-10 as much as 0.5% is 19.5 cm; Sika Viscocrete-10 as much as 1% is 21.9 cm; Sika Viscocrete-10 as much as 1.5% is 23 cm; and Sika Viscocrete-10 as much as 1.8% is 24.7 cm. Based on these test results, the conclusion is addition of Sika Viscocrete-10 is able to enhance the workability value of concrete, so it is easy to work. Concrete mix design using the American Concrete Institute (ACI). Specimens used in this study is a standard concrete cylinder diameter of 150 mm and a height of 300 m, tested after the age of 14 days. Number of test specimens for all treatments is 25 with 5 specimens in each treatment. The average compressive strength of concrete with normal mixture is 295.43 kg/cm2; for concrete with Sika Viscocrete-10 as mush as 0.5% is of 376.50 kg/cm2; Sika Viscocrete-10 as mush as 1% is 452.94 kg/cm2; Sika Viscocrete-10 as mush as 1.5% is 501.63 kg/cm;2 and Sika Viscocrete-10 as mush as 1.8% is 515.78 kg/cm2. Concrete compressive strength greater with increasing percentage of Sika Viscocrete-10.

scholarly journals PENGARUH PENAMBAHAN QUICKCURE CX TERHADAP UJI KUAT TEKAN BETON K-500

2020 ◽  
Vol 6 (4) ◽  
Author(s):  
Erny Agusri ◽  
Wahyu Pratama Jaya
Keyword(s):  
Compressive Strength ◽  
Strength Test ◽  
Technological Innovations ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
A Value ◽  
Compressive Strength Test ◽  
Compressive Strength Of Concrete ◽  
Average Compressive Strength

Quickcure CX is a chemical for concrete designed using the latest technological innovations, this added material can accelerate and increase the compressive strength of concrete by 5 - 10% and can reduce the moisture content in the concrete mixture by 5 - 10%. The purpose of this study was to increase and accelerate the effect of the compressive strength value of concrete produced by Quickcure CX added material on K-500 concrete.The research sample is a cube-shaped test object with a size of 15cmx15cmx15cm. There are 4 sample variations, namely: Normal Concrete, Normal Concrete + Quickcure cx 0.25%, Normal Concrete + Quickcure cx 0.45%, and Normal Concrete + Quickcure cx 0.65%, each variation consisting of 15 samples.After conducting the concrete compressive strength test, this study obtained the highest average compressive strength test results in Normal Concrete (503.2kg / cm2), Normal Concrete + Quickcure cx 0.25% (513.8kg / cm2), Normal Concrete + Quickcure 0.45% (536.4kg / cm2) and Normal Concrete + Quickcure cx 0.65% at 551.6kg / cm2 at the age of 28 days. So of the 4 variations in the value of the compressive strength test of concrete, it still increases in Normal Concrete + Quickcure cx 0.65%, and accelerating the concrete does not accelerate because the average age is 21 days with a variation of Normal Concrete + Quickcure cx 0.65% with a value of 488.8 kg / cm2 so the concrete has not reached the compressive strength that was planned.Keywords: Concrete, Quikcure CX, Compressive Strength, K-500

Variasi Penambahan Sika Cim Dan Fiber Kawat Pada Beton Mutu Fc’ 30 Mpa

2018 ◽  
Vol 9 (2) ◽  
pp. 67-73
Author(s):  
M Zainul Arifin
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Astm Method ◽  
Additive Type ◽  
Composition Variation ◽  
Compressive Strength Of Concrete

This research was conducted to determine the value of the highest compressive strength from the ratio of normal concrete to normal concrete plus additive types of Sika Cim with a composition variation of 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1 , 50% and 1.75% of the weight of cement besides that in this study also aims to find the highest tensile strength from the ratio of normal concrete to normal concrete in the mixture of sika cim composition at the highest compressive strength above and after that added fiber wire with a size diameter of 1 mm in length 100 mm with a ratio of 1% of material weight. The concrete mix plan was calculated using the ASTM method, the matrial composition of the normal concrete mixture as follows, 314 kg / m3 cement, 789 kg / m3 sand, 1125 kg / m3 gravel and 189 liters / m3 of water at 10 cm slump, then normal concrete added variations of the composition of sika cim 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1.5%, 1.75% by weight of cement and fiber, the tests carried out were compressive strength of concrete and tensile strength of concrete, normal maintenance is soaked in fresh water for 28 days at 30oC. From the test results it was found that the normal concrete compressive strength at the age of 28 days was fc1 30 Mpa, the variation in the addition of the sika cim additive type mineral was achieved in composition 0.75% of the cement weight of fc1 40.2 Mpa 30C. Besides that the tensile strength test results were 28 days old with the addition of 1% fiber wire mineral to the weight of the material at a curing temperature of 30oC of 7.5%.

Experimental Study on Sand and Cement Replacement by Termite Mound Soil

2019 ◽  
pp. 279-287
Author(s):  
Harish R ◽  
Ramesh S ◽  
Tharani A ◽  
Mageshkumar P
Keyword(s):  
Experimental Study ◽  
Experimental Investigation ◽  
Compressive Strength ◽  
Natural Environment ◽  
Fine Aggregate ◽  
Test Results ◽  
Termite Mound ◽  
Cement Concrete ◽  
Cement Ratio ◽  
Compressive Strength Of Concrete

This paper presents the results of an experimental investigation of the compressive strength of concrete cubes containing termite mound soil. The specimens were cast using M20 grade of concrete. Two mix ratios for replacement of sand and cement are of 1:1.7:2.7 and 1:1.5:2.5 (cement: sand: aggregate) with water- cement ratio of 0.45 and varying combination of termite mound soil in equal amount ranging from 30% and 40% replacing fine aggregate (sand) and cement from 10%,15%,20% were used. A total of 27 cubes, 18 cylinders and 6 beams were cast by replacing fine aggregate, specimens were cured in water for 7,14 and 28 days. The test results showed that the compressive strength of the concrete cubes increases with age and decreases with increasing percentage replacement of cement and increases with increasing the replacement of sand with termite mound soil cured in water. The study concluded that termite mound cement concrete is adequate to use for construction purposes in natural environment.

Research on mechanical behavior of L-shaped multi-cell concrete-filled steel tubular stub columns under axial compression

2018 ◽  
Vol 22 (2) ◽  
pp. 427-443 ◽  
Author(s):  
Jiepeng Liu ◽  
Hua Song ◽  
Yuanlong Yang
Keyword(s):  
Finite Element ◽  
Compressive Strength ◽  
Bearing Capacity ◽  
Thickness Ratio ◽  
Steel Plates ◽  
Test Results ◽  
Finite Element Program ◽  
Element Program ◽  
Compressive Strength Of Concrete ◽  
Stub Columns

A total of 11 L-shaped multi-cell concrete-filled steel tubular stub columns were fabricated and researched in axial compression test. The key factors of width-to-thickness ratio D/ t of steel plates in column limb and prism compressive strength of concrete fck were investigated to obtain influence on failure mode, bearing capacity, and ductility of the specimens. The test results show that the constraint effect for concrete provided by multi-cell steel tube cannot be ignored. The ductility decreases with the increase of width-to-thickness ratio D/ t of steel plates in column limb. The bearing capacity increases and the ductility decreases with the increase in prism compressive strength of concrete fck. A finite element program to calculate concentric load–displacement curves of L-shaped multi-cell concrete-filled steel tubular stub columns was proposed and verified by the test results. A parametric analysis with the finite element program was carried out to study the influence of the steel ratio α, steel yield strength fy, prism compressive strength of concrete fck, and width-to-thickness ratio D/ t of steel plates in column limb on the stiffness, bearing capacity and ductility. Furthermore, the design method of bearing capacity was determined based on mainstream concrete-filled steel tubular codes.

Drying Shrinkage of Concrete Affected by Content of Stone Powder in Proto-Machine-Made Sand

2010 ◽  
Vol 152-153 ◽  
pp. 1176-1179 ◽  
Author(s):  
Feng Lan Li ◽  
Qian Zhu
Keyword(s):  
Compressive Strength ◽  
Standard Method ◽  
Structural Engineering ◽  
Drying Shrinkage ◽  
Shrinkage Strain ◽  
Test Results ◽  
Similar Test ◽  
Mix Proportion ◽  
Compressive Strength Of Concrete ◽  
Main Factor

To improve the application of the new proto-machine-made sand in structural engineering, tests are carried out to study the drying shrinkage of concrete affected by stone powder in proto- machine-made sand. The target cubic compressive strength of concrete is 55 MPa, the main factor varied in mix proportion of concrete is the contents of stone powder by mass of proto-machine-made sand from 3 % to 16 %. The drying shrinkage strains of concrete are measured by the standard method at the ages of 1 d, 3 d, 7 d, 14 d, 28 d, 60 d, 90 d, 120 d, 150 d and 180 d. Based on test results, the drying shrinkage of concrete affected by the contents of stone powder in proto-machine-made sand is analyzed and compared with that of similar test of concrete with traditional machine-made sand, which shows that there is the optimum content of stone powder resulting in the lower drying shrinkage of concrete. The formula for predicting drying shrinkage strain of concrete is proposed.

scholarly journals The effect of zeolite addition on parameters of concrete containing recycled ceramic aggregate

2018 ◽  
Vol 45 ◽  
pp. 00116
Author(s):  
Jacek Szulej ◽  
Paweł Ogrodnik
Keyword(s):  
Compressive Strength ◽  
Material Properties ◽  
Frost Resistance ◽  
Environmentally Friendly ◽  
Concrete Material ◽  
Dominant Component ◽  
Concrete Mix ◽  
Aluminous Cement ◽  
Compressive Strength Of Concrete ◽  
Zeolite Tuff

In the paper it was decided to recognize the material characteristics of concrete based on ceramic aggregate, aluminous cement with the addition of zeolite (5%, 10%, 15%) and air entraining admixture. Aggregate crushed to 2 fractions was used for designing the concrete mix : 0-4 mm, and 4-8 mm. The research involved the use of clinoptilolite derived from the zeolite tuff deposit at Sokyrnytsya (Transcarpathia, Ukraine). The dominant component in the zeolite is clinoptilolite in an amount of about 75%. The research carried out by the authors showed that the addition of zeolite, among others, increases the compressive strength of concrete, significantly improves the frost resistance, which in the case of using only aluminous cement is very low. The obtained results confirm the possibility of using the above-mentioned components, which improve the concrete material properties and are environmentally friendly.

Sign in / Sign up

Export Citation Format

Share Document