scholarly journals Influence of blends of diesel and renewable fuels on CI engine emissions over transient engine conditions.

2018 ◽  
Author(s):  
Adriaan Smuts Van Niekerk ◽  
Benjamin Drew ◽  
Neil Larsen ◽  
Peter Kay
Keyword(s):  
Fuel Consumption ◽  
Co2 Emissions ◽  
Nox Emissions ◽  
Compression Ignition ◽  
Engine Emissions ◽  
Drive Cycle ◽  
Fuel Blend ◽  
High Oxygen Content ◽  
Fuel Blends ◽  
Ci Engine

To reduce the amount of carbon dioxide released from transportation the EU has implemented legislation to mandate the renewable content of petrol and diesel fuels. However, due to the complexity of the combustion process the addition of renewable content, such as biodiesel and ethanol, can have a detrimental effect on other engine emissions. In particular the engine load can have a significant impact on the emissions. Most research that have studied this issue are based on steady state tests, that are unrealistic of real world driving and will not capture the difference between full and part loads. This study aims to address this by investigating the effect of renewable fuel blends of diesel, biodiesel and ethanol on the emissions of a compression ignition engine tested over the World Harmonised Light Vehicle Test Procedure (WLTP). Diesel, biodiesel and ethanol were blended to form binary and ternary blends, the ratios were determined by Design of Experiments (DoE). The total amount of emissions for CO, CO2 and NOx as well as the fuel consumption, were measured from a 2.4 liter compression ignition (CI) engine running over the WLTP drive cycle. The results depicted that percentages smaller than 10 % of ethanol in the fuel blend can reduce CO emissions, CO2 emissions as well as NOx emissions, but increases fuel consumption with increasing percentage of ethanol in the fuel blend. Blends with biodiesel resulted in minor increases in CO emissions due to the engine being operated in the low and medium load regions over the WLTP. CO2 emissions as well as NOx emissions increased as a result of the high oxygen content in biodiesel which promoted better combustion. Fuel consumption increased for blends with biodiesel as a result from biodiesel's lower heating value. All the statistical models describing the engine responses were significant and this demonstrated that a mixture DoE is suitable to quantify the effect of fuel blends on an engine's emissions response. An optimised ternary blend of B2E9 was found to be suitable as a 'drop in' fuel that will reduce harmful emissions of CO emissions by approximately 34 %, NOx emissions by 10 % and CO2 emissions by 21 % for transient engine operating scenarios such as the WLTP drive cycle.

Enhancing Diesel Engine Performance and Reducing Emissions Using Binary Biodiesel Fuel Blend

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Paramvir Singh ◽  
S. R. Chauhan ◽  
Varun Goel ◽  
Ashwani K. Gupta
Keyword(s):  
Fuel Consumption ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Transport Sector ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Fuel Blend ◽  
Fuel Blends ◽  
Fuel Mixing ◽  
Ci Engines

Fossil fuel consumption provides a negative impact on the human health and environment in parallel with the decreased availability of this valuable natural resource for the future generations to use as a source of chemical energy for all applications in energy, power, and propulsion. The diesel fuel consumption in the transport sector is higher than the gasoline in most developing countries for reasons of cost and economy. Biodiesel fuel offers a good replacement for diesel fuel in compression ignition (CI) diesel engines. Earlier investigations by the authors revealed that a blend of 70% amla seed oil biodiesel and 30% eucalyptus oil (AB70EU30) is the favorable alternative renewable fuel blend that can be used as a fuel in diesel engines. With any fuel, air/fuel mixing and mixture preparation impact efficiency, emissions, and performance in CI engines. Minor adjustments in engine parameters to improve air/fuel mixing and combustion are deployable approaches to achieve good performance with alternative fuel blends in CI engines. This paper provides the role of a minor modification to engine parameters (compression ratio, injection timing, and injection pressure) on improved performance using the above mixture of binary fuel blends (AB70EU30). The results showed that the use of AB70EU30 in modified engine resulted in higher brake thermal efficiency and lower brake specific fuel consumption compared to normal diesel for improved combustion that also resulted in very low tailpipe emissions.

scholarly journals Investigation on Blending Effects of Gasoline Fuel with N-Butanol, DMF, and Ethanol on the Fuel Consumption and Harmful Emissions in a GDI Vehicle

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1845 ◽  
Author(s):  
Haifeng Liu ◽  
Xichang Wang ◽  
Diping Zhang ◽  
Fang Dong ◽  
Xinlu Liu ◽  
...  
Keyword(s):  
Steady State ◽  
Fuel Consumption ◽  
Large Fraction ◽  
Direct Injection ◽  
Transient State ◽  
Gasoline Direct Injection ◽  
Nox Emissions ◽  
Fuel Blends ◽  
Wide Range ◽  
Oxygenated Fuel

The effects of three kinds of oxygenated fuel blends—i.e., ethanol-gasoline, n-butanol-gasoline, and 2,5-dimethylfuran (DMF)-gasoline-on fuel consumption, emissions, and acceleration performance were investigated in a passenger car with a chassis dynamometer. The engine mounted in the vehicle was a four-cylinder, four-stroke, turbocharging gasoline direct injection (GDI) engine with a displacement of 1.395 L. The test fuels include ethanol-gasoline, n-butanol-gasoline, and DMF-gasoline with four blending ratios of 20%, 50%, 75%, and 100%, and pure gasoline was also tested for comparison. The original contribution of this article is to systemically study the steady-state, transient-state, cold-start, and acceleration performance of the tested fuels under a wide range of blending ratios, especially at high blending ratios. It provides new insight and knowledge of the emission alleviation technique in terms of tailoring the biofuels in GDI turbocharged engines. The results of our works showed that operation with ethanol–gasoline, n-butanol–gasoline, and DMF–gasoline at high blending ratios could be realized in the GDI vehicle without any modification to its engine and the control system at the steady state. At steady-state operation, as compared with pure gasoline, the results indicated that blending n-butanol could reduce CO2, CO, total hydrocarbon (THC), and NOX emissions, which were also decreased by employing a higher blending ratio of n-butanol. However, a high fraction of n-butanol increased the volumetric fuel consumption, and so did the DMF–gasoline and ethanol–gasoline blends. A large fraction of DMF reduced THC emissions, but increased CO2 and NOX emissions. Blending n-butanol can improve the equivalent fuel consumption. Moreover, the particle number (PN) emissions were significantly decreased when using the high blending ratios of the three kinds of oxygenated fuels. According to the results of the New European Drive Cycle (NEDC) cycle, blending 20% of n-butanol with gasoline decreased CO2 emissions by 5.7% compared with pure gasoline and simultaneously reduced CO, THC, NOX emissions, while blending ethanol only reduced NOX emissions. PN and particulate matter (PM) emissions decreased significantly in all stages of the NEDC cycle with the oxygenated fuel blends; the highest reduction ratio in PN was 72.87% upon blending 20% ethanol at the NEDC cycle. The high proportion of n-butanol and DMF improved the acceleration performance of the vehicle.

scholarly journals Combustion characteristics of compression ignition engine fuelled with rapeseed oil–diesel fuel–n-butanol blends

2021 ◽  
Vol 76 ◽  
pp. 17
Author(s):  
Jakub Čedík ◽  
Martin Pexa ◽  
Bohuslav Peterka ◽  
Miroslav Müller ◽  
Michal Holubek ◽  
...  
Keyword(s):  
Vegetable Oils ◽  
Diesel Fuel ◽  
Rapeseed Oil ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Solid Particles ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Blend ◽  
Fuel Blends

Liquid biofuels for compression ignition engines are often based on vegetable oils. In order to be used in compression ignition engine the vegetable oils have to be processed because of their high viscosity or it is also possible to use vegetable oils in fuel blends. In order to decrease the viscosity of the fuel blends containing crude vegetable oil the alcohol-based fuel admixtures can be used. The paper describes the effect of rapeseed oil–diesel fuel–n-butanol blends on combustion characteristics and solid particles production of turbocharged compression ignition engine. The 10% and 20% concentrations of n-butanol in the fuel blend were measured and analysed. The engine Zetor 1204, located in tractor Zetor Forterra 8641 with the power of 60kW and direct injection was used for the measurement. The engine was loaded through power take off shaft of the tractor using mobile dynamometer MAHA ZW500. The measurement was carried out in stabilized conditions at 20%, 60% and 100% engine load. The engine speed was kept at 1950 rpm. Tested fuel blends showed lower production of solid particles than diesel fuel and lower peak cylinder pressure and with increasing concentration of n-butanol in the fuel blend the ignition delay was prolonged and premixed phase of combustion was increased.

Experimental Evaluation of Cooking Oil (Carotene Oil) as Biodiesel Blended on Compression Ignition (CI) Engine

2011 ◽  
Vol 110-116 ◽  
pp. 2234-2238
Author(s):  
A.R. Norwazan ◽  
A.K. Zulkiffli ◽  
M.S. Abd Rahim
Keyword(s):  
Fuel Consumption ◽  
Power Output ◽  
Alternative Fuels ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Compression Ignition ◽  
Cooking Oil ◽  
Brake Power ◽  
Ci Engine ◽  
Biodiesel Blend

Biodiesel is an alternative fuels for diesel engine with the blending process by chemically combination of vegetable or animal oil and diesel fuels. It is proved that the biodiesel can be used without any modification on the compression ignition (CI) engine. In this study, the cooking oil of namely carotene is used to produce the biodiesel blend fuels in various percentages. The biodiesel blend and diesel fuel are evaluated to analyze the engine performances in 4 cylinder inline CI engine. The characteristics of engine performances namely brake power output and brake specific fuel consumption are measured with various loads applied. The fuel properties of biodiesel blend are investigated namely density, dynamics viscosity and kinetic viscosity. The experimental results show that the performance of biodiesel B10 is better than it counterpart namely diesel in terms of brake power output and brake specific fuel consumption (BSFC).

scholarly journals ANALYSIS OF NOx EMISSIONS AND SPECIFIC FUEL CONSUMPTION OF A DIESEL ENGINE OPERATING WITH DIESEL/BIODIESEL BLENDS

2013 ◽  
Vol 12 (1) ◽  
pp. 11 ◽  
Author(s):  
C. V. Teixeira ◽  
A. B. Caldeira ◽  
M. J. Colaço
Keyword(s):  
Fuel Consumption ◽  
Combustion Process ◽  
Environmental Issues ◽  
Specific Fuel Consumption ◽  
Qualitative Assessment ◽  
Nox Emissions ◽  
Biodiesel Blends ◽  
Electric Generator ◽  
Respiratory Problems ◽  
Fuel Blends

This study aims to examine experimentally the NOx emissions and the performance of a motor AGRALE M90, single cylinder, operating with diesel and biodiesel blends. The engine was linked to an electric generator, which provided 1500 W, 3000 W and 4500 W to an electrical system. The engine was tested with fuel blends containing different amounts of commercial diesel (B4) with palm biodiesel (B100). NOx emissions, as well as the specific fuel consumption of diesel, biodiesel and their mixtures were measured and analyzed. In this study, emissions of NOx have been prioritized over other pollutants by environmental issues and techniques. Air pollution by NOx causes serious respiratory problems. Furthermore, emissions of NOx enable a qualitative assessment of the combustion process. The results show that the commercial diesel has better performance in terms of energy efficiency and NOx emissions.

scholarly journals Outlook for Direct Use of Sunflower and Castor Oils as Biofuels in Compression Ignition Diesel Engines, Being Part of Diesel/Ethyl Acetate/Straight Vegetable Oil Triple Blends

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4836
Author(s):  
Laura Aguado-Deblas ◽  
Rafael Estevez ◽  
Jesús Hidalgo-Carrillo ◽  
Felipa M. Bautista ◽  
Carlos Luna ◽  
...  
Keyword(s):  
Ethyl Acetate ◽  
Fuel Consumption ◽  
Kinematic Viscosity ◽  
Fossil Fuels ◽  
Cetane Number ◽  
Calorific Value ◽  
Compression Ignition ◽  
High Oxygen Content ◽  
Electric Generator ◽  
Object Of Study

Today, biofuels are indispensable in the implementation of fossil fuels replacement processes. This study evaluates ethyl acetate (EA) as a solvent of two straight vegetable oils (SVOs), castor oil (CO), and sunflower oil (SO), in order to obtain EA/SVO double blends that can be used directly as biofuels, or along with fossil diesel (D), in the current compression-ignition (C.I.) engines. The interest of EA as oxygenated additive lies not only in its low price and renewable character, but also in its very attractive properties such as low kinematic viscosity, reasonable energy density, high oxygen content, and rich cold flow properties. Revelant fuel properties of EA/SVO double and D/EA/SVO triple blends have been object of study including kinematic viscosity, pour point (PP), cloud point (CP), calorific value (CV), and cetane number (CN). The suitability of using these blends as fuels has been tested by running them on a diesel engine electric generator, analyzing their effect on engine power output, fuel consumption, and smoke emissions. Results obtained indicate that the D/EA/SO and D/EA/CO triple blends, composed by up to 24% and 36% EA, respectively, allow a fossil diesel substitution up to 60–80% providing power values very similar to conventional diesel.In addition, in exchange of a slight fuel consumption, a very notable lessening in the emission of pollutants as well as a better behavior at low temperatures, as compared to diesel, are achieved.

scholarly journals Certain investigation in a compression ignition engine using rice bran methyl ester fuel blends with ethanol additive

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 535-542 ◽  
Author(s):  
Arumugam Krishnan ◽  
Maran Punnaivanam ◽  
Satheeshkumar Koodalingam
Keyword(s):  
Global Warming ◽  
Methyl Ester ◽  
Rice Bran ◽  
Rice Bran Oil ◽  
Calorific Value ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Blend ◽  
Fuel Blends ◽  
Hc Emissions

In this study and analysis, the physical properties such as calorific value, viscosity, flash, and fire point temperatures of rice bran oil methyl ester were found. The rice bran oil biodiesel has been prepared by transesterification process from pure rice bran oil in the presence of methanol and NaOH. Moreover, property enhancement of rice bran oil methyl ester was also made by adding different additives such as ethanol in various proportions. Rice bran oil methyl ester with 1, 3, and 5% ethanol were analyzed for its fuel properties. The effects of diesel-B20ROME blends with ethanol additive of 1, 3, and 5% on a compression ignition engine were examined considering its emissions. It is found that the increase in biodiesel concentration in the fuel blend influences CO2 and NOx emissions. On the other hand CO and HC emissions are reduced. It is interesting to observe the emission as ethanol-B20ROME blends, reduces CO2 and NOx which are the major contributors to global warming. As the NOx and CO2 can be reduced drastically by the proposed blends, the global warming can be reduced considerably.

AN ASSESSMENT OF VARIOUS NANOADDITIVES AND TRIBO-CORROSION WITH WASTE COOKING BIODIESEL FUELED IN A DIESEL ENGINE

2021 ◽  
Author(s):  
Yogaraj D ◽  
Jaichandar S
Keyword(s):  
Steady State ◽  
Diesel Fuel ◽  
Peak Load ◽  
Nox Emissions ◽  
Cylinder Pressure ◽  
Flash Temperature ◽  
Wear Scar Diameter ◽  
Fuel Blend ◽  
Fuel Blends ◽  
Temperature Parameter

The waste cooking biodiesel's steady-state coefficient of friction rate of fuel blends are B90 (18.2%), B60 (7.2%), B20 (16.72%), B10 (30.8%), and diesel (38.77%) higher compared with B40 fuel blend and wear scar diameter of the fuel blends from B40 to B100 had a minimal range of 0.5mm. The flash temperature parameter results higher from B40 to B100 fuel blends, and the corrosion rate was minimal for B40 and B50 fuel blends. Afterward, the fuel blend B40 (40% WCO+60% Diesel fuel) was chosen as fuel, along with Cerium (25ppm), Zinc (25ppm), and Titanium nanoparticles (25ppm) were selected as fuel additives. The B40+D60+Titanium (25ppm) blend resulted in improved BTE and 3.83% lowered BSEC comparison with diesel fuel. Then the fuel blend, B40+D80+Titanium (25ppm), resulted in 2.08% reduced HC, 36.36% CO, and 16.25% smoke emissions, along with marginally 8.5% higher NOx emissions comparison with diesel fuel. Also, the fuel blend, B40+D80+Titanium (25ppm) combustions characteristics are the equivalent trend of cylinder pressure (58.82 bar) and HRR (66.65 J/deg CA) related to diesel fuel at peak load.

Sign in / Sign up

Export Citation Format

Share Document