Cam Phaser Actuation Rate Performance Impact on Fuel Consumption and NOx Emissions Over the FTP-75 Drive Cycle

2003 ◽  
Author(s):  
Frédéric Jacquelin ◽  
Reinhard Burk ◽  
Russell J. Wakeman
Keyword(s):  
Fuel Consumption ◽  
Nox Emissions ◽  
Rate Performance ◽  
Performance Impact ◽  
Drive Cycle

scholarly journals Influence of blends of diesel and renewable fuels on CI engine emissions over transient engine conditions.

2018 ◽  
Author(s):  
Adriaan Smuts Van Niekerk ◽  
Benjamin Drew ◽  
Neil Larsen ◽  
Peter Kay
Keyword(s):  
Fuel Consumption ◽  
Co2 Emissions ◽  
Nox Emissions ◽  
Compression Ignition ◽  
Engine Emissions ◽  
Drive Cycle ◽  
Fuel Blend ◽  
High Oxygen Content ◽  
Fuel Blends ◽  
Ci Engine

To reduce the amount of carbon dioxide released from transportation the EU has implemented legislation to mandate the renewable content of petrol and diesel fuels. However, due to the complexity of the combustion process the addition of renewable content, such as biodiesel and ethanol, can have a detrimental effect on other engine emissions. In particular the engine load can have a significant impact on the emissions. Most research that have studied this issue are based on steady state tests, that are unrealistic of real world driving and will not capture the difference between full and part loads. This study aims to address this by investigating the effect of renewable fuel blends of diesel, biodiesel and ethanol on the emissions of a compression ignition engine tested over the World Harmonised Light Vehicle Test Procedure (WLTP). Diesel, biodiesel and ethanol were blended to form binary and ternary blends, the ratios were determined by Design of Experiments (DoE). The total amount of emissions for CO, CO2 and NOx as well as the fuel consumption, were measured from a 2.4 liter compression ignition (CI) engine running over the WLTP drive cycle. The results depicted that percentages smaller than 10 % of ethanol in the fuel blend can reduce CO emissions, CO2 emissions as well as NOx emissions, but increases fuel consumption with increasing percentage of ethanol in the fuel blend. Blends with biodiesel resulted in minor increases in CO emissions due to the engine being operated in the low and medium load regions over the WLTP. CO2 emissions as well as NOx emissions increased as a result of the high oxygen content in biodiesel which promoted better combustion. Fuel consumption increased for blends with biodiesel as a result from biodiesel's lower heating value. All the statistical models describing the engine responses were significant and this demonstrated that a mixture DoE is suitable to quantify the effect of fuel blends on an engine's emissions response. An optimised ternary blend of B2E9 was found to be suitable as a 'drop in' fuel that will reduce harmful emissions of CO emissions by approximately 34 %, NOx emissions by 10 % and CO2 emissions by 21 % for transient engine operating scenarios such as the WLTP drive cycle.

scholarly journals Investigation of Effect on Environmental Performance of Using LNG as Fuel for Engines in Seaport Tugboats

2021 ◽  
Vol 9 (2) ◽  
pp. 123
Author(s):  
Sergejus Lebedevas ◽  
Lukas Norkevičius ◽  
Peilin Zhou
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Baltic Sea ◽  
Impact Assessment ◽  
Fuel Consumption ◽  
Dual Fuel ◽  
Nox Emissions ◽  
The Baltic Sea ◽  
Emission Analysis ◽  
The Baltic

Decarbonization of ship power plants and reduction of harmful emissions has become a priority in the technological development of maritime transport, including ships operating in seaports. Engines fueled by diesel without using secondary emission reduction technologies cannot meet MARPOL 73/78 Tier III regulations. The MEPC.203 (62) EEDI directive of the IMO also stipulates a standard for CO2 emissions. This study presents the results of research on ecological parameters when a CAT 3516C diesel engine is replaced by a dual-fuel (diesel-liquefied natural gas) powered Wartsila 9L20DF engine on an existing seaport tugboat. CO2, SO2 and NOx emission reductions were estimated using data from the actual engine load cycle, the fuel consumption of the KLASCO-3 tugboat, and engine-prototype experimental data. Emission analysis was performed to verify the efficiency of the dual-fuel engine in reducing CO2, SO2 and NOx emissions of seaport tugboats. The study found that replacing a diesel engine with a dual-fuel-powered engine led to a reduction in annual emissions of 10% for CO2, 91% for SO2, and 65% for NOx. Based on today’s fuel price market data an economic impact assessment was conducted based on the estimated annual fuel consumption of the existing KLASCO-3 seaport tugboat when a diesel-powered engine is replaced by a dual-fuel (diesel-natural gas)-powered engine. The study showed that a 33% fuel costs savings can be achieved each year. Based on the approved methodology, an ecological impact assessment was conducted for the entire fleet of tugboats operating in the Baltic Sea ports if the fuel type was changed from diesel to natural gas. The results of the assessment showed that replacing diesel fuel with natural gas achieved 78% environmental impact in terms of NOx emissions according to MARPOL 73/78 Tier III regulations. The research concludes that new-generation engines on the market powered by environmentally friendly fuels such as LNG can modernise a large number of existing seaport tugboats, significantly reducing their emissions in ECA regions such as the Baltic Sea.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Methodology to Evaluate the Fuel Economy of a Multimode Combustion Engine With Three-Way Catalytic Converter

2014 ◽  
Author(s):  
Sandro P. Nüesch ◽  
Anna G. Stefanopoulou ◽  
Li Jiang ◽  
Jeffrey Sterniak
Keyword(s):  
Fuel Economy ◽  
Combustion Engine ◽  
Catalytic Converter ◽  
Oxygen Storage ◽  
Nox Emissions ◽  
Combustion Mode ◽  
Mode Switch ◽  
Drive Cycle ◽  
Finite State ◽  
The Impact

Highly diluted, low temperature homogeneous charge compression ignition (HCCI) combustion leads to ultra-low levels of engine-out NOx emissions. A standard drive cycle, however, would require switches between HCCI and spark-ignited (SI) combustion modes. In this paper a methodology is introduced, investigating the fuel economy of such a multimode combustion concept in combination with a three-way catalytic converter (TWC). The TWC needs to exhibit unoccupied oxygen storage sites in order to show acceptable performance. But the lean exhaust gas during HCCI operation fills the oxygen storage and leads to a drop in NOx conversion efficiency. Eventually the levels of NOx become unacceptable and a mode switch to a fuel rich combustion mode is necessary in order to deplete the oxygen storage. The resulting lean-rich cycling leads to a penalty in fuel economy. In order to evaluate the impact of those penalties on fuel economy, a finite state model for combustion mode switches is combined with a longitudinal vehicle model and a phenomenological TWC model, focused on oxygen storage. The aftertreatment model is calibrated using combustion mode switch experiments from lean HCCI to rich spark-assisted HCCI and back. Fuel and emissions maps acquired in steady state experiments are used. Two depletion strategies are compared in terms of their influence on drive cycle fuel economy and NOx emissions.

A Multidisciplinary Approach for the Comprehensive Assessment of Integrated Rotorcraft–Powerplant Systems at Mission Level

2014 ◽  
Vol 137 (1) ◽  
Author(s):  
Ioannis Goulos ◽  
Fakhre Ali ◽  
Konstantinos Tzanidakis ◽  
Vassilios Pachidis ◽  
Roberto d'Ippolito
Keyword(s):  
Environmental Impact ◽  
Fuel Consumption ◽  
Comprehensive Assessment ◽  
Pollutant Emissions ◽  
Operational Performance ◽  
Civil Aviation ◽  
Accurate Estimation ◽  
Nox Emissions ◽  
Reactor Model ◽  
Stirred Reactor

This paper presents an integrated methodology for the comprehensive assessment of combined rotorcraft–powerplant systems at mission level. Analytical evaluation of existing and conceptual designs is carried out in terms of operational performance and environmental impact. The proposed approach comprises a wide-range of individual modeling theories applicable to rotorcraft flight dynamics and gas turbine engine performance. A novel, physics-based, stirred reactor model is employed for the rapid estimation of nitrogen oxides (NOx) emissions. The individual mathematical models are implemented within an elaborate numerical procedure, solving for total mission fuel consumption and associated pollutant emissions. The combined approach is applied to the comprehensive analysis of a reference twin-engine light (TEL) aircraft modeled after the Eurocopter Bo 105 helicopter, operating on representative mission scenarios. Extensive comparisons with flight test data are carried out and presented in terms of main rotor trim control angles and power requirements, along with general flight performance charts including payload-range diagrams. Predictions of total mission fuel consumption and NOx emissions are compared with estimated values provided by the Swiss Federal Office of Civil Aviation (FOCA). Good agreement is exhibited between predictions made with the physics-based stirred reactor model and experimentally measured values of NOx emission indices. The obtained results suggest that the production rates of NOx pollutant emissions are predominantly influenced by the behavior of total air inlet pressure upstream of the combustion chamber, which is affected by the employed operational procedures and the time-dependent all-up mass (AUM) of the aircraft. It is demonstrated that accurate estimation of on-board fuel supplies ahead of flight is key to improving fuel economy as well as reducing environmental impact. The proposed methodology essentially constitutes an enabling technology for the comprehensive assessment of existing and conceptual rotorcraft–powerplant systems, in terms of operational performance and environmental impact.

scholarly journals Cleaning up the air: Effectiveness of air quality policy for SO<sub>2</sub> and NO<sub><i>x</i></sub> emissions in China

2016 ◽  
Author(s):  
Ronald J. van der A ◽  
Bas Mijling ◽  
Jieying Ding ◽  
Maria Elissavet Koukouli ◽  
Fei Liu ◽  
...  
Keyword(s):  
Air Quality ◽  
Fuel Consumption ◽  
Fossil Fuel ◽  
Transport Sector ◽  
Nox Emissions ◽  
So2 Emissions ◽  
Provincial Level ◽  
Fossil Fuel Consumption ◽  
Public Data ◽  
Quality Policy

Abstract. Air quality observations by satellite instruments are spatially consistent, and have a regular temporal resolution, which make them very useful in studying long-term trends in atmospheric species. To monitor air quality trends in China for the period 2005–2015 we derive SO2 columns and NOx emissions on a provincial level with an unprecedented accuracy. To put these trends into perspective they are compared with public data on energy consumption and the environmental policies of China. We distinguish the effect of air quality regulations from economic growth by comparing them relatively to fossil fuel consumption. Pollutant levels, per unit of fossil fuel, are used to assess the effectiveness of air quality regulations. We note that the desulphurisation regulations enforced in 2005–2006 only had a significant effect in the years 2008–2009 when a much stricter control of the actual use of the installations began. For national NOx emissions a distinct decreasing trend is only visible since 2012, but the emission peak year differs from province to province. Unlike SO2, emissions of NOx are highly related to traffic. Furthermore, regulations for NOx emissions are partly decided on a provincial level. The last three years show both a reduction in SO2 and NOx emissions per fossil fuel unit, since the authorities have implemented several new environmental regulations. Despite an increasing fossil fuel consumption and a growing transport sector, the effects of air quality policy in China are clearly visible. Without the air quality regulations the concentration of SO2 would be almost 3 times higher and the NO2 concentrations would be at least 30 % higher than they are today in China.

An Investigation of the Fuel Economy of a Drive Cycle Developed Using the Road Load Energy Criterion

2021 ◽  
Author(s):  
Peter Vasquez ◽  
Edwin Quiros ◽  
Gerald Jo Denoga ◽  
Robert Michael Corpus ◽  
Robert James Lomotan
Keyword(s):  
Fuel Consumption ◽  
Fuel Economy ◽  
Energy Criterion ◽  
Chassis Dynamometer ◽  
Drive Cycle ◽  
The Road ◽  
Energy Error ◽  
Road Load ◽  
Metro Manila ◽  
Road Data

Abstract Efforts to mitigate climate change include lowering of greenhouse gas emissions by reducing fuel consumption in the transport sector. Various vehicle technologies and interventions for better fuel economy eventually require chassis dynamometer testing using drive cycles for validation. As such, the methodology to generate these drive cycles from on-road data should produce drive cycles that closely represent actual on-road driving from the fuel economy standpoint. This study presents a comparison of the fuel economy measured from a drive cycle developed using road load energy as a major assessment criterion and the actual on-road fuel economy of a 2013 Isuzu Crosswind utility vehicle used in the UV Express transport fleet in Metro Manila, Philippines. In this approach to drive cycle construction from on-road data, the ratio of the total road load energy of the generated drive cycle to that of the on-road trip is made the same ratio as their respective durations. On-road velocity and fuel consumption were recorded as the test vehicle traversed the 42.5 km. Sucat to Lawton route and vice versa in Metro Manila. Gathered data were processed to generate drive cycles using the modified Markov Chain approach. Three drive cycles of decreasing duration, based on the practicality of testing on a chassis dynamometer, were generated using three arbitrary data compression ratios. These drive cycles were tested using the same vehicle on the chassis dynamometer and compared with the on-road data using road load energy, fuel economy, average speed, and maximum acceleration. For the 893-seconds drive cycle generated, the road load energy error was 3.93% and fuel economy difference of 1.14%. For the 774-seconds cycle generated, the road load energy error was 4.34% and fuel economy difference was 0.91%. For the 664-seconds drive cycle, the road load energy error was 3.68% and fuel economy difference was 0.91%. On-road fuel economy for the 42.5-km. route averaged over nine round trips was 8.785 km/L. Based on the results, the road load energy criterion approach of drive cycle construction methodology can generate drive cycles which can very closely estimate on-road fuel economy.

scholarly journals An Investigation of the Influence of Gas Injection Rate Shape on High-Pressure Direct-Injection Natural Gas Marine Engines

Energies ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2571 ◽  
Author(s):  
Jingrui Li ◽  
Jietuo Wang ◽  
Teng Liu ◽  
Jingjin Dong ◽  
Bo Liu ◽  
...  
Keyword(s):  
High Pressure ◽  
Natural Gas ◽  
Fuel Consumption ◽  
Direct Injection ◽  
Gas Injection ◽  
Injection Rate ◽  
Emission Characteristics ◽  
Nox Emissions ◽  
Indicated Mean Effective Pressure ◽  
Marine Engines

High-pressure direct-injection (HPDI) natural gas marine engines are widely used because of their higher thermal efficiency and lower emissions. The effects of different injection rate shapes on the combustion and emission characteristics were studied to explore the appropriate gas injection rate shapes for a low-speed HPDI natural gas marine engine. A single-cylinder model was established and the CFD model was validated against experimental data from the literature; then, the combustion and emission characteristics of five different injection rate shapes were analyzed. The results showed that the peak values of in-cylinder pressure and heat release rate profiles of the triangle shape were highest due to the highest maximum injection rate, which occurred in a phase close to the top dead center. The shorter combustion duration of the triangle shape led to higher indicated mean effective pressure (IMEP) and NOx emissions compared with other shapes. The higher initial injection rates of the rectangle and slope shapes had a negative effect on the ignition delay periods of pilot fuel, which resulted in lower in-cylinder temperature and NOx emissions. However, due to the lower in-cylinder temperature, the engine power output was also lower. Otherwise, soot, unburned hydrocarbon (UHC), and CO emissions and indicated specific fuel consumption (ISFC) increased for both rectangle and slope shapes. The trapezoid and wedge shapes achieved a good balance between fuel consumption and emissions.

Optimization of Engine Efficiency for Diesel Engine Equipped With EGR-VGT and Aftertreatment Systems

2019 ◽  
Author(s):  
Kuo Yang ◽  
Pingen Chen
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Engines ◽  
Intrinsic Property ◽  
Nox Emission ◽  
Nox Emissions ◽  
Minimum Phase ◽  
Engine Efficiency ◽  
Simulation Results ◽  
Aftertreatment Systems

Abstract Engine efficiency improvement is very critical for medium to heavy-duty vehicles to reduce Diesel fuel consumption and enhance U.S. energy security. The tradeoff between engine efficiency and NOx emissions is an intrinsic property that prevents modern Diesel engines, which are generally equipped with exhaust gas recirculation (EGR) and variable geometry turbocharger (VGT), from achieving the optimal engine efficiency while meeting the stringent NOx emission standards. The addition of urea-based selective catalytic reduction (SCR) systems to modern Diesel engine aftertreatment systems alleviate the burden of NOx emission control on Diesel engines, which in return creates extra freedom for optimizing Diesel engine efficiency. This paper proposes two model-based approaches to locate the optimal operating point of EGR and VGT in the air-path loop to maximize the indicated efficiency of turbocharged diesel engine. Simulation results demonstrated that the engine brake specific fuel consumption (BSFC) can be reduced by up to 1.6% through optimization of EGR and VGT, compared to a baseline EGR-VGT control which considers both NOx emissions and engine efficiency on engine side. The overall equivalent BSFCs are 1.8% higher with optimized EGR and VGT control than with the baseline control. In addition, the influence of reducing EGR valve opening on the non-minimum phase behavior of the air path loop is also analyzed. Simulation results showed slightly stronger non-minimum phase behaviors when EGR is fully closed.

CI Engine Model Predictive Control With Availability Destruction Minimization

2018 ◽  
Author(s):  
Muataz Abotabik ◽  
Richard T. Meyer
Keyword(s):  
Energy Source ◽  
Model Predictive Control ◽  
Fuel Consumption ◽  
Predictive Control ◽  
Alternative Fuels ◽  
Combustion Engine ◽  
Tracking Error ◽  
Specific Fuel Consumption ◽  
Nox Emissions ◽  
Compression Ignition Engine

Major interests in the automotive industry include the use of alternative fuels and reduced fuel usage to address fuel supply security concerns and regulatory requirements. The majority of previous internal combustion engine (ICE) control strategies consider only the First Law of Thermodynamics (FLT). However, FLT is not able to distinguish losses in work potential due to irreversibilities, e.g., up to 25% of fuel exergy may be lost to irreversibilities. To account for these losses, the Second Law of Thermodynamics (SLT) is applicable. The SLT is used to identify the quality of an energy source via availability since not all the energy in a particular energy source is available to produce work; therefore optimal control that includes availability may be another path toward reduced fuel use. Herein, Model Predictive Control (MPC) is developed for both FLT and SLT approaches where fuel consumption is minimized in the former and availability destruction in the latter. Additionally, both include minimization of load tracking error. The controls are evaluated in the simulation of a single cylinder naturally aspirated compression ignition engine that is fueled with either 20% biodiesel and 80% diesel blend or diesel only. Control simulations at a constant engine speed and changing load profile show that the SLT approach results in higher SLT efficiency, reduced specific fuel consumption, and decreased NOx emissions. Further, compared to use of diesel only, use of the biodiesel blend resulted in less SLT efficiency, higher specific fuel consumption, and lower NOx emissions.

Sign in / Sign up

Export Citation Format

Share Document