scholarly journals Influence of Cutting Parameters on Chatter and Tool Wear During End Milling of Stainless Steel Conducted on VMC

1970 ◽  
Vol 3 (2) ◽  
Author(s):  
A.K.M.N. AMIN, M. IMRAN AND M. ARIF
Keyword(s):  
Stainless Steel ◽  
Tool Wear ◽  
Surface Finish ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Wear Intensity ◽  
Depth Of Cut ◽  
Machined Surface ◽  
Milling Operation

Stainless steels are a group of difficult to machine work materials. The difficulty in machining stainless steels is manifested in high contact length and stresses, formation of serrated chips and development of chatter resulting in high tool wear rates and poor machined surface finish. The paper focuses on the performance of TiN coated-carbide inserts in machining stainless steel specimens in end milling operation performed on vertical machining centre (VMC). The performance of the tool is evaluated from the point of view of its wear intensity, mechanism of failure and generation and effect of chatter on tool wear and vice versa. The investigations were aimed at determining the effect of cutting parameters, specifically cutting speed, feed and depth of cut, on chatter amplitude, tool wear rate, mechanism of tool wear and using these data and machined surface roughness values from previous work to come up with recommended values of cutting parameters for semi-finish and finish end milling operation of stainless steel work materials. For recording vibration signals a dual channel portable signal analyzers was used and the signals were analyzed using Pulse Multi-analyzer version 4.2 software. Tool wear was measured using an optical microscope with digital readout capabilities along 3 axes. The tool wear mechanisms were studied under a scanning electron microscope (SEM). Results of the investigation show that acceleration amplitudes generally increase with cutting speed and the magnitude of tool flank wears. It has been also found that an increase in feed and depth of cut leads to higher acceleration amplitudes. The most common wear mechanisms observed during machining of stainless steel are attrition, micro and macro chipping of the tool at lower cutting speeds, and diffusion and mechanical failures due to intensive chatter at higher speeds. It has been also established that stable cutting speeds with relatively low tool wear intensity and satisfactory machined surface finish can be achieved through proper selection of cutting parameters. A table of recommended cutting conditions has been developed for almost chatter free machining with low tool wear intensity and satisfactory surface finish. Key Words: Vertical Machining Centre, Machinability, Chatter, Cutting, Tool life.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

The Investigation of Prediction Surface Roughness from Machining Forces in End Milling Processes

2011 ◽  
Vol 486 ◽  
pp. 91-94 ◽  
Author(s):  
Jabbar Abbas ◽  
Amin Al-Habaibeh ◽  
Dai Zhong Su
Keyword(s):  
Surface Roughness ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Irregular Waves ◽  
Depth Of Cut ◽  
End Mill ◽  
Machined Surface ◽  
Machining Forces ◽  
Mill Cutter

Surface roughness is one of the most significant parameters to determine quality of machined parts. Surface roughness is defined as a group of irregular waves in the surface, measured in micrometers (μm). Many investigations have been performed to verify the relationship between surface roughness and cutting parameters such as cutting speed, feed rate and depth of cut. To predict the surface produced by end milling, surface roughness models have been developed in this paper using the machining forces by assuming the end mill cutter as a cantilever beam rigidly or semi- rigidly supported by tool holder. An Aluminium workpiece and solid carbide end mill tools are used in this work. Model to predict surface roughness has been developed. Close relationship between machined surface roughness and roughness predicted using the measured forces signals.

Prediction of Surface Roughness in High Speed Machining of Inconel 718

2011 ◽  
Vol 264-265 ◽  
pp. 1193-1198
Author(s):  
Mokhtar Suhaily ◽  
A.K.M. Nurul Amin ◽  
Anayet Ullah Patwari
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Inconel 718 ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
High Speed Machining

Surface finish and dimensional accuracy is one of the most important requirements in machining process. Inconel 718 has been widely used in the aerospace industries. High speed machining (HSM) is capable of producing parts that require little or no grinding/lapping operations within the required machining tolerances. In this study small diameter tools are used to achieve high rpm to facilitate the application of low values of feed and depths of cut to investigate better surface finish in high speed machining of Inconel 718. This paper describes mathematically the effect of cutting parameters on Surface roughness in high speed end milling of Inconel 718. The mathematical model for the surface roughness has been developed in terms of cutting speed, feed rate, and axial depth of cut using design of experiments and the response surface methodology (RSM). Central composite design was employed in developing the surface roughness models in relation to primary cutting parameters. Machining were performed using CNC Vertical Machining Center (VMC) with a HES510 high speed machining attachment in which using a 4mm solid carbide fluted flat end mill tool. Wyko NT1100 optical profiler was used to measure the definite machined surface for obtaining the surface roughness data. The predicted results are in good agreement with the experimental one and hence the model can be efficiently used to predict the surface roughness value with in the specified cutting conditions limit.

Effect of cutting parameters on tool life during end milling of AISI 4340 under MQL condition

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ahsana Aqilah Ahmad ◽  
Jaharah A. Ghani ◽  
Che Hassan Che Haron
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanism ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Content Type ◽  
Radial Depth

Purpose The purpose of this paper is to study the cutting performance of high-speed regime end milling of AISI 4340 by investigating the tool life and wear mechanism of steel using the minimum quantity lubrication (MQL) technique to deliver the cutting fluid. Design/methodology/approach The experiments were designed using Taguchi L9 orthogonal array with the parameters chosen: cutting speed (between 300 and 400 m/min), feed rate (between 0.15 and 0.3 mm/tooth), axial depth of cut (between 0.5 and 0.7 mm) and radial depth of cut (between 0.3 and 0.7 mm). Toolmaker microscope, optical microscope and Hitachi SU3500 Variable Pressure Scanning Electron Microscope used to measure tool wear progression and wear mechanism. Findings Cutting speed 65.36%, radial depth of cut 24.06% and feed rate 6.28% are the cutting parameters that contribute the most to the rate of tool life. The study of the tool wear mechanism revealed that the oxide layer was observed during lower and high cutting speeds. The former provides a cushion of the protective layer while later reduce the surface hardness of the coated tool Originality/value A high-speed regime is usually carried out in dry conditions which can shorten the tool life and accelerate the tool wear. Thus, this research is important as it investigates how the use of MQL and cutting parameters can prolong the usage of tool life and at the same time to achieve a sustainable manufacturing process.

Preheating in End Milling of AISI D2 Hardened Steel with Coated Carbide Inserts

2009 ◽  
Vol 83-86 ◽  
pp. 56-66 ◽  
Author(s):  
Mohd Amri Lajis ◽  
A.K.M. Nurul Amin ◽  
A.N. Mustafizul Karim ◽  
A.M.K. Hafiz
Keyword(s):  
Tool Wear ◽  
Surface Finish ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Inductive Heating ◽  
Machining Parameters ◽  
Aisi D2 ◽  
Coated Carbide

This study was conducted to investigate the effect of preheating through inductive heating mechanism in end milling of AISI D2 hardened steel (60-62 HRC) by using coated carbide tool inserts. Apart from preheating, two other machining parameters such as cutting speed and feed were varied while the depth of cut constant was kept constant. Tool wear phenomenon and machined surface finish were found to be significantly affected by preheating temperature and other two variables. End milling operation was performed on a Vertical Machining Centre (VMC). Preheating of the work material to a higher temperature range resulted in a noticeable reduction in tool wear rate leading to a longer tool life. In addition, improved surface finish was obtained with surface roughness values lower than 0.4 μm, leaving a possibility of skipping the grinding and polishing operations for certain applications.

Empirical Expression of Tool Wear When Face Milling 416 SS

2009 ◽  
Author(s):  
Patricia Mun˜oz de Escalona ◽  
Paul G. Maropoulos
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Face Milling ◽  
Machining Process ◽  
Depth Of Cut ◽  
Milling Operation ◽  
Increase Tool Life ◽  
The Cost

During a machining process, cutting parameters must be taken into account, since depending on them the cutting edge starts to wear out to the point that tool can fail and needs to be change, which increases the cost and time of production. Since wear is a negative phenomenon on the cutting tool, due to the fact that tool life is reduced, it is important to optimize the cutting variables to be used during the machining process, in order to increase tool life. This research is focused on the influence of cutting parameters such as cutting speed, feed per tooth and axial depth of cut on tool wear during a face milling operation. The Taguchi method is applied in this study, since it uses a special design of orthogonal array to study the entire parameters space, with only few numbers of experiments. Also a relationship between tool wear and the cutting parameters is presented. For the studies, a martensitic 416 stainless steel was selected, due to the importance of this material in the machining of valve parts and pump shafts.

scholarly journals Effect of Some Manfacturing Parameters on Machining of Extruded Al-Al2O3 Composites

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
A. Fathy ◽  
M. Abdelhameed ◽  
F. Shehata
Keyword(s):  
Wear Rate ◽  
Surface Finish ◽  
Volume Fraction ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machined Surface ◽  
Aluminum Powders ◽  
Wide Range ◽  
Coated Carbide

A wide range of particulate metal matrix composites (PMMCs) of alumina and aluminum powders was formed using powder metallurgy techniques followed by extrusions at various extrusion ratios. The machining characteristics of the extruded PMMC were investigated. Results showed significant effects of weight fractions of reinforcement and extrusion ratios on tool wear and surface integrity of machined surface. The wear rate of cutting tool decreased rapidly with increasing the cutting parameters: cutting speed, feed, and depth of cut, however cutting speed is shown to be more effective. Sudden breakage of tool inserts occurred when the experiment started at high cutting speed. Wear rate has also decreased by decreasing volume fraction of reinforcement particles. Coating carbide tools have significantly improved the tool life. Coated tools showed 5% decrease in flank wear size compared to uncoated tools. This was valid within tested range of weight fractions and extrusion ratios. The surface finish of machined surfaces deteriorated when coated carbide tools were used. However, surface finish did not change significantly when volume fractions or extrusion ratios were altered.

Energy conscious cryogenic machining of Ti-6Al-4V titanium alloy

2016 ◽  
Vol 232 (10) ◽  
pp. 1690-1706 ◽  
Author(s):  
Alborz Shokrani ◽  
Vimal Dhokia ◽  
Stephen T Newman
Keyword(s):  
Energy Consumption ◽  
Tool Wear ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cryogenic Cooling ◽  
Depth Of Cut ◽  
Cryogenic Machining ◽  
Coolant Pump ◽  
Cutting Speeds

Manufacturing and, in particular, machining are responsible for a significant portion of global industrial energy consumption (25%). Previous research has shown that precise selection of cutting parameters can improve the energy consumption of machining processes. Cryogenic machining has attracted significant attention for improving the machinability of difficult-to-machine materials while also eliminating the environmental and health issues associated with the use of cutting fluids. Despite the advantages, there is a considerable research gap in cryogenic milling operations. This article investigates the effect of cryogenic cooling using liquid nitrogen in end milling of Ti-6Al-4V. A robust and rigorous methodology was developed and a series of machining experiments were conducted using a combination of cutting parameters repeated at dry, flood and cryogenic cooling environments. The investigations indicated that cryogenic cooling considerably reduce tool wear when compared to dry and flood cooling while allowing for using higher cutting speeds. The cutting tool used for cryogenic machining at 200 m/min cutting speed, 0.03 mm/tooth feed rate and 5 mm depth of cut showed minimum flank wear. Furthermore, the investigations demonstrated that using the machine’s coolant pump in flood cooling resulted in higher power and energy consumption than dry and cryogenic cooling. This article clearly shows that higher material removal rates are required in order to minimise specific machining energy. Therefore, since cutting speed is limited in dry machining, cryogenic machining is the most favourable as higher cutting speeds can be used. Using cryogenic machining at 200 m/min cutting speed resulted in an 88% reduction in energy consumption of the machine tool as compared to flood cooling at 30 m/min while minimum tool wear (10 µm) was detected. This clearly demonstrates the significant capabilities of cryogenic machining when compared with more conventional machining approaches.

Reducing Tool Wear in CNC End Milling Operation Using Progressive Feed Rate

2014 ◽  
Vol 592-594 ◽  
pp. 716-723
Author(s):  
K.S. Badrinathan ◽  
L. Karunamoorthy
Keyword(s):  
Tool Wear ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Milling Operation ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Cnc End Milling

This study focuses on the effect of cutting parameters on the tool wear in a CNC end milling operation. Major factors which influence the tool wear are spindle speed, feed rate and depth of cut. Conventionally constant feed rate is used. In this work a concept of progressive feed rate is introduced. AISI 1045 steel has been chosen as it is widely used in manufacturing. Design of Experiments (DOE) technique was adopted to conduct the experiments. Experiments were conducted for both the existing and the proposed feed rate method and the tool wear was compared. A statistical model was developed using Design Expert software. The predicted values were compared with the experimental values and were found to be in close agreement. The model adequacy was checked using ANOVA technique.

scholarly journals Analysis of tool vibration and surface roughness with tool wear progression in hard turning: An experimental and statistical approach

2020 ◽  
Vol 14 (1) ◽  
pp. 6461-6472
Author(s):  
Nitin Ambhore ◽  
Dinesh Kamble ◽  
Satish Chinchanikar
Keyword(s):  
Tool Wear ◽  
Surface Quality ◽  
Hard Turning ◽  
Cutting Speed ◽  
Dimensional Accuracy ◽  
Cutting Parameters ◽  
Tangential Direction ◽  
Depth Of Cut ◽  
Machined Surface ◽  
Tool Vibrations

The machined surface quality and dimensional accuracy obtained during hard turning is prominently gets affected due to tool wear and cutting tool vibrations. With this view, the results of tool wear progression on surface quality and acceleration amplitude is presented while machining AISI 52100 hard steel. Central Composite Rotatable Design (CCRD) is employed to develop experimental plan. The results reported that vibration signals sensed in a tangential direction (Vz) are most sensitive and found higher than the vibrations in the feed direction (Vx) and depth of cut direction (Vy). The acceleration signals in all three directions are observed to increase with the advancement of tool wear and good surface finish is observed as tool wear progresses up-to 0.136mm. The vibration amplitude is discovered high in the range 3 kHz – 10 kHz within selected cutting parameter range (cutting speed 60-180mm/min, feed 0.1-0.5mm/rev, depth of cut 0.1-0.5mm). The investigation is extended for the development of multiple regression models with regression coefficients value 0.9. These models found statically significant and give dependable estimates between a tool vibrations and cutting parameters.

Sign in / Sign up

Export Citation Format

Share Document