scholarly journals Characteristics for Improvement of Compressive Strength of Geopolymers Made of Mixed Binders

2020 ◽  
Vol 7 ◽  
Author(s):  
Tatsuya Koumoto
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Melting Furnace ◽  
Chemical Mechanism ◽  
Portland Cement Concrete ◽  
Hard Materials ◽  
Steel Making ◽  
Furnace Slag

Geopolymers are composite hard materials made by mixing binders, such as fly ash and slags, and activators, such as NaOH and sodium silicate. The chemical mechanism for hardening composite materials, aluminosilicate binders, with alkaline activators is known as a geopolymer reaction. Geopolymers have recently been developed to be used as a replacement for Portland cement concrete. Industrial by-products such as fly ash, steel making slags, and garbage melting furnace slags can be made into geopolymers in a process that emits less carbon dioxide than in the cement making process. This reduction in CO2 emission is important because CO2 is one of the substances known to contribute to global warming. In the future, further uses of these fly ash and slags must be explored. The development of high compressive strength geopolymers using fly ash and slags will strongly contribute to the fields of construction, geotechnical engineering, and architecture. So far, ground blast furnace slag has yielded the highest compressive strength geopolymer among various kind of binders such as fly ash, ground stainless steel-making slag, and garbage melting furnace slags. A potential use for the poor binders, yielding low compressive strength geopolymers, is to combine it with a richer binder to create stronger products. This paper examines the characteristics for improvement of compressive strength of geopolymers for the binders in various mixture ratios of poor binders and the ground blast furnace slag.

Optimization of Concrete Porous Mix Using Slag as Substitute Material for Cement and Aggregates

2017 ◽  
Vol 865 ◽  
pp. 282-288 ◽  
Author(s):  
Jul Endawati ◽  
Rochaeti ◽  
R. Utami
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Blast Furnace Slag ◽  
Environmental Effect ◽  
Substitution Effect ◽  
Main Concern ◽  
Binder Material ◽  
Furnace Slag

In recent years, sustainability and environmental effect of concrete became the main concern. Substituting cement with the other cementitious material without decreasing mechanical properties of a mixture could save energy, reduce greenhouse effect due to mining, calcination and limestone refining. Therefore, some industrial by-products such as fly ash, silica fume, and Ground Iron Blast Furnace Slag (GIBFS) would be used in this study to substitute cement and aggregate. This substitution would be applied on the porous concrete mixture to minimize the environmental effect. Slag performance will be optimized by trying out variations of fly ash, silica fume, and slag as cement substitution material in mortar mixture. The result is narrowed into two types of substitution. First, reviewed from the fly ash substitution effect on binder material, highest compressive strength 16.2 MPa was obtained from mixture composition 6% fly ash, 3% silica fume and 17% grinding granular blast-furnace slag. Second, reviewed from slag types as cement substitution and silica fume substitution, highest compressive strength 15.2 MPa was obtained from mortar specimens with air-cooled blast furnace slag. It composed with binder material 56% Portland composite cement, 15% fly ash, 3% silica fume and 26% air-cooled blast furnace slag. Considering the cement substitution, the latter mixture was chosen.

scholarly journals Protective Geopolymer Coatings Containing Multi-Componential Precursors: Preparation and Basic Properties Characterization

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3448
Author(s):  
Chenhui Jiang ◽  
Aiying Wang ◽  
Xufan Bao ◽  
Zefeng Chen ◽  
Tongyuan Ni ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Portland Cement ◽  
Adhesive Strength ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Rapid Test ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This paper presents an experimental investigation on geopolymer coatings (GPC) in terms of surface protection of civil structures. The GPC mixtures were prepared with a quadruple precursor simultaneously containing fly ash (FA), ground granulated blast-furnace slag (GBFS), metakaolin (MK), and Portland cement (OPC). Setting time, compressive along with adhesive strength and permeability, were tested and interpreted from a perspective of potential applications. The preferred GPC with favorable setting time (not shorter than 120 min) and desirable compressive strength (not lower than 35 MPa) was selected from 85 mixture formulations. The results indicate that balancing strength and setting behavior is viable with the aid of the multi-componential precursor and the mixture design based on total molar ratios of key oxides or chemical elements. Adhesive strength of the optimized GPC mixtures was ranged from 1.5 to 3.4 MPa. The induced charge passed based on a rapid test of coated concrete specimens with the preferred GPC was 30% lower than that of the uncoated ones. Setting time of GPC was positively correlated with η[Si/(Na+Al)]. An abrupt increase of setting time occurred when the molar ratio was greater than 1.1. Compressive strength of GPC was positively affected by mass contents of ground granulated blast furnace slag, metakaolin and ordinary Portland cement, and was negatively affected by mass content of fly ash, respectively. Sustained seawater immersion impaired the strength of GPC to a negligible extent. Overall, GPC potentially serves a double purpose of satisfying the usage requirements and achieving a cleaner future.

scholarly journals Alkali-activated concretes based on fly ash and blast furnace slag: Compressive strength, water absorption and chloride permeability

2020 ◽  
Vol 40 (2) ◽  
Author(s):  
Daniela Eugenia Angulo-Ramírez ◽  
William Gustavo Valencia-Saavedra ◽  
Ruby Mejía de Gutiérrez
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Water Absorption ◽  
Blast Furnace Slag ◽  
Construction Materials ◽  
Chloride Ion ◽  
Chloride Permeability ◽  
Alkaline Activator ◽  
Furnace Slag

Concretes based on alkaliactivated binders have attracted considerable attention as new alternative construction materials, which can substitute Portland Cement (OPC) in several applications. These binders are obtained through the chemical reaction between an alkaline activator and reactive aluminosilicate materials, also named precursors. Commonly used precursors are fly ash (FA), blast furnace slag (GBFS), and metakaolin. The present study evaluated properties such as compressive strength, rate of water absorption (sorptivity), and chloride permeability in two types of alkaliactivated concretes (AAC): FA/GBFS 80/20 and GBFS/OPC 80/20. OPC and GBFS/OPC* concretes without alkaliactivation were used as reference materials. The highest compressive strength was observed in the FA/GBFS concrete, which reported 26,1% greater strength compared to OPC concrete after 28 days of curing. The compressive strength of alkaliactivated FA/GBFS 80/20 and GBFS/OPC 80/20 was 61 MPa and 42 MPa at 360 days of curing, respectively. These AAC showed low permeability to the chloride ion and a reduced water absorption. It is concluded that these materials have suitable properties for various applications in the construction sector.

Development of High Performance Concrete Containing Admixture in Nuclear Power Plants

2013 ◽  
Vol 357-360 ◽  
pp. 1062-1065 ◽  
Author(s):  
Jeong Eun Kim ◽  
Wan Shin Park ◽  
Song Hui Yun ◽  
Do Gyeum Kim ◽  
Jea Myoung Noh
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Modulus Of Elasticity ◽  
Blast Furnace Slag ◽  
High Performance ◽  
Splitting Tensile Strength ◽  
Furnace Slag

This paper presents the results of an experimental study on the compressive strength, splitting tensile strength and modulus of elasticity characteristics of high performance concrete. These tests were carried out to evaluate the mechanical properties of HPC for up to 7 and 28 days. Mixtures were prepared with water to binder ratio of 0.40. Two mixtures were containing fly ash at 25%, silica fume at 5% cement replacement, respectively. Another mixture was contains blast furnace slag and fly ash at 25%. Three standard 100¥a200 cylinder specimens were prepared. HPC showed improvement in the compressive strength and splitting tensile strength when ordinary Portland cement was replaced with silica fume. Compare with specimens FA25 and BS25FA25, specimen SF5 showed much more modulus of elasticity. It shows that the use of the blast furnace slag of 25% and fly ash of 25% cement replacement has caused a small increase in compressive strength and splitting tensile strength and modulus of elasticity compared to the only use of fly ash of 25% at 28days. The results indicated that the use of blast furnace slag or silica fume provided the good performance compare to fly ash when the mechanical properties of the high performance concretes were taken into account.

scholarly journals Investigation of Mechanical Properties, Durability and Microstructure of Low-Clinker High-Performance Concretes Incorporating Ground Granulated Blast Furnace Slag, Siliceous Fly Ash and Silica Fume

2021 ◽  
Vol 11 (2) ◽  
pp. 830
Author(s):  
Katarzyna Konieczna ◽  
Karol Chilmon ◽  
Wioletta Jackiewicz-Rek
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
High Performance ◽  
Cement Clinker ◽  
Water Penetration ◽  
Granulated Blast Furnace Slag ◽  
Portland Cement Clinker ◽  
Furnace Slag

The main assumption of eco-efficient High-Performance Concrete (HPC) design is the reduction of Portland cement clinker content without negatively affecting the composite’s mechanical and durability properties. In this paper, three low-clinker HPC mixtures incorporating slag cement (CEM III/B as per EN 197-1) and Supplementary Cementitious Materials (SCMs)—Ground Granulated Blast Furnace Slag (GGBFS), Siliceous Fly Ash (SFA) and Silica Fume (SF)—were designed. The maximum amount of Portland cement clinker from CEM III/B varied from 64 to 116 kg in 1 m3 of concrete mix. The compressive strength of HPC at 2, 7, 14, 28, 56, 90 days, and 2 years after casting, as well as the modulus of elasticity on 2-year-old specimens, was tested. The depth of water penetration under pressure and internal frost resistance in freeze–thaw tests were evaluated after 56 days of curing. Additionally, the concrete pH value tests were performed. The microstructure of 2-year-old HPC specimens was analyzed using Scanning Electron Microscopy (SEM). The research proved that it is possible to obtain low-clinker High-Performance Concretes that reach compressive strength of 76–92 MPa after 28 days of curing, show high values of modulus of elasticity (49–52 GPa) as well as increased resistance to frost and water penetration under pressure.

scholarly journals Preparation of Foamed Phosphogypsum Lightweight Materials by Incorporating Cementitious Additives

2019 ◽  
Vol 25 (3) ◽  
pp. 340-347
Author(s):  
Ting WANG ◽  
Xiaojian GAO ◽  
Jian WANG
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Portland Cement ◽  
Blast Furnace Slag ◽  
Building Materials ◽  
Water Resistance ◽  
Hydrated Lime ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

As a byproduct of phosphoric acid industry, phosphogypsum has many environmental problems. In order to recycle phosphogypsum to manufacture lightweight building materials, cementitious additives including fly ash, ground granulate blast-furnace slag and Portland cement were added to improve strength and water-resistance and different volume of foam was added to reduce the bulk density. The results show that hydrated lime can improve mechanical strength and water resistance of PG paste and the optimal dosage of hydrated lime is 6 %. Higher addition of fly ash or ground granulated blast-furnace slag improves the fluidity and delays the setting time of PG paste. The addition of 10 ~ 20 % fly ash results in a little reducing influence and 10 % ground granulated blast-furnace slag leads to an increase of 20.7 % for 28 days compressive strength of hardened PG specimen. The higher addition of Portland cement results in the better mechanical strength and water resistance of PG specimens. The 28day compressive and flexural strength reaches 25.9 MPa and 8.9 MPa respectively for the 25 % Portland cement mixture. PG based lightweight building materials can prepared by the addition of 60 % volume of air foam, with compressive strength of 1.7 MPa, bulk density of 521.7 kg/m3 and thermal conductivity of 0.0724 W/(m·K). DOI: http://dx.doi.org/10.5755/j01.ms.25.3.19910

scholarly journals Evolution of Mechanical Properties with Time of Fly-Ash-Based Geopolymer Mortars under the Effect of Granulated Ground Blast Furnace Slag Addition

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1135 ◽  
Author(s):  
Mateusz Sitarz ◽  
Izabela Hager ◽  
Marta Choińska
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Modulus Of Elasticity ◽  
Blast Furnace Slag ◽  
Energy Savings ◽  
Pulse Velocity ◽  
Partial Replacement ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

Geopolymers are considered to alternatives to Portland cement, providing an opportunity to exploit aluminosilicate wastes or co-products with promising performances in the construction sector. This research is aimed at investigating the strength of fly-ash-geopolymers of different ages. The effect of granulated blast furnace slag (GGBFS) as a partial replacement of fly ash (FA) on the tensile (ft) and compressive strength (fc), as well as the modulus of elasticity, is investigated. The main advantage of the developed geopolymer mixes containing GGBFS is their ability to set and harden at room temperature with no need for heating to obtain binding properties, reducing the energy consumption of their production processes. This procedure presents a huge advantage over binders requiring heat curing, constituting a significant energy savings and reduction of CO2 emissions. It is found that the development of strength strongly depends on the ratio of fly-ash to granulated blast furnace slag. With the highest amount of GGBFS, the compressive strength of geopolymers made of fly-ash reached 63 MPa after 28 days of curing at ambient temperature. The evolution of compressive strength with time is correlated with the development of ultrasound pulse velocity methods, which are used to evaluate maturity. The modulus of elasticity changes with strength and the relationship obtained for the geopolymer is presented on the basis of typical models used for cement-based materials. The tensile to compressive strength ratios of the tested geopolymers are identified as higher than for cementitious binders, and the ft(fc) relationship is juxtaposed with dependencies known for cement binders, showing that the square root function gives the best fit to the results.

Sign in / Sign up

Export Citation Format

Share Document