scholarly journals TESTING THE EFFECTIVENESS OF ORGANIC ACIDS AS A PRESERVATIVE OF ANIMAL FEED INGREDIENTS

2021 ◽  
Vol 9 (2) ◽  
pp. 102-111
Author(s):  
Rizqa Adisti ◽  
Wijayanti Indah ◽  
Retanani Yuli
Keyword(s):  
Specific Gravity ◽  
Moisture Content ◽  
Organic Acids ◽  
Propionic Acid ◽  
Wheat Bran ◽  
Lauric Acid ◽  
Sorbic Acid ◽  
Physical Parameters ◽  
Index Test ◽  
Feed Ingredients

This research was conducted in the Laboratory of Feed Industry Technology, Faculty of Animal Husbandry, Bogor Agricultural University, Bogor. The purpose of this study was to determine the effectiveness of using organic acids as preservatives in feed ingredients in the form of pollard and wheat bran based on physical parameters. This study used a completely randomized design with 2 factorials in the form of feed type and organic acid type with 3 replications, samples were stored for 6 weeks and then data were collected in the form of moisture content, pile angle, pile density and specific gravity. The results showed that organic acids affected the moisture content but had no effect on pile density, pile angle and specific gravity. The type of feed affects the value of moisture content, pile angle, pile density and specific gravity. Based on the results of the effectiveness index test, it is known that the total yield value on pollard with 1% lauric acid is 0.64, sorbic acid is 0.35 and propionic acid is 0.77, while wheat bran with lauric acid is 1.07 at -1 sorbic acid. .39 and in propionic acid 2.64. The conclusion of this research is that propionic acid can be used as a preservative for pollard and wheat bran    

Properties of Gliricidia Wood (Gliricidia sepium) lntercropped with Cocoa (Theobroma cocoa) in Malaysia

2014 ◽  
Vol 11 (1) ◽  
pp. 51
Author(s):  
Mohd Helmy Ibrahim ◽  
Mohd Nazip Suratman ◽  
Razali Abd Kader
Keyword(s):  
Cell Wall ◽  
Specific Gravity ◽  
Moisture Content ◽  
Wall Thickness ◽  
Age Groups ◽  
Gliricidia Sepium ◽  
Cell Wall Thickness ◽  
Tree Age ◽  
Lumen Diameter ◽  
Significant Difference

Trees planted from agroforestry practices can become valuable resources in meeting the wood requirements of many nations. Gliricidia sepium is an exotic species introduced to the agricultural sector in Malaysia mainly for providing shade for cocoa and coffee plantations. This study investigates its wood physical properties (specific gravity and moisture content) and fibre morphology (length, lumen diameter and cell wall thickness) of G. sepium at three intervals according to age groups ( three, five and seven years of ages). Specific gravity (0.72) was significantly higher at seven years ofage as compared to five (0.41) and three (0.35) years age group with a mean of 0.43 (p<0.05). Mean moisture content was 58.3% with no significant difference existing between the tree age groups. Fibre diameter (22.4 mm) was significantly lower (p<0.05) for the trees which were three years of age when compared to five and seven years age groups (26.6 mm and 24. 7 mm), respectively. Means of fibre length, lumen diameter and cell wall thickness were 0.83 mm, 18.3 mm, and 6.2 mm, respectively, with no significant differences detected between trees in all age groups. Further calculation on the coefficient of suppleness and runkel ratio suggest that wood from G.sepium may have the potential for insulation board manufacturing and paper making. However, future studies should experiment the utilisation of this species for these products to determine its full potential.

scholarly journals Comparison of Geotechnical Properties of Laterite, Kaolin and Peat

2015 ◽  
Vol 773-774 ◽  
pp. 1438-1442 ◽  
Author(s):  
Siti Aimi Nadia Mohd Yusoff ◽  
I. Bakar ◽  
Devapriya Chitral Wijeyesekera ◽  
Adnan Zainorabidin ◽  
Aziman Madun
Keyword(s):  
Specific Gravity ◽  
Moisture Content ◽  
Initial Moisture Content ◽  
General Information ◽  
Geotechnical Properties ◽  
Grain Size Analysis ◽  
Size Analysis ◽  
Proctor Test ◽  
Construction Operation ◽  
Soil Behaviour

This paper compares some geotechnical properties of Kaolin, Laterite and Peat. Laterite was collected from Bukit Banang while Peat sample was collected from Parit Nipah, both locations were in Batu Pahat, Johor. Meanwhile, kaolin that was used in this research was manufactured kaolin. These soil samples were subjected to routine laboratory analysis and resulting data were analyzed statistically using a correlation analysis. A laboratory testing program consists of “Basic properties test” to obtain general information on the materials (e.g Natural moisture content, Atterberg Limit, Specific gravity, grain size analysis, chemical composition and pH) and “Geotechnical properties tests” to measure specific properties that characterize soil behaviour for design and constructability assessments (e.g Standard Proctor Test, Unconfined Compressive Strength and CBR).The results showed that the Natural/initial moisture content for laterite, peat and kaolin is 22.54%, 480.61% and 0.22% respectively. Meanwhile Specific gravity for each soil was in the range 1.50-2.79.It was also found that the pH of all soil is acidic which lay in the range of 3.76-5.95.The UCS for the optimally compacted sample of laterite is 445.77 kPa, kaolin is 199.23 kPa and for peat is 58.70 kPa. This paper summarizes the result of analysis performed on all tests conducted. Based on the results, the geotechnical property of the soil is a highly dependent with the type of soil and therefore, determining the soil characterization and the soil strength should be considered during the planning phase of any earthwork construction operation.

Selected Properties of Parallel Strand Lumber Made from Southern Pine and Yellow-Poplar

Holzforschung ◽  
2003 ◽  
Vol 57 (2) ◽  
pp. 207-212 ◽  
Author(s):  
Y. Liu ◽  
A.W.C. Lee
Keyword(s):  
Compressive Strength ◽  
Shear Strength ◽  
Specific Gravity ◽  
Moisture Content ◽  
Dimensional Stability ◽  
Modulus Of Rupture ◽  
Southern Pine ◽  
Yellow Poplar ◽  
Average Modulus ◽  
Parallel Strand Lumber

Summary This study was conducted to explore basic physical and mechanical properties of parallel strand lumber (PSL) made exclusively from southern pine and yellow-poplar, respectively, and to examine their relationships using statistical analysis. Small specimens were prepared from commercial southern pine PSL and yellow-poplar PSL billets and tested for specific gravity, moisture content, dimensional stability, bending properties, shear strength and compressive strength. Results indicate average specific gravity of southern pine PSL is higher than that of yellow-poplar PSL, while their average moisture content and dimensional stability are very similar. Southern pine PSL has higher average modulus of elasticity but lower average modulus of rupture than yellow-poplar PSL. While average longitudinal shear strength does not exhibit differences between southern pine PSL and yellow-poplar PSL, average compressive strength of southern pine PSL is higher than that of yellow-poplar PSL. There are positive correlations among modulus of elasticity, modulus of rupture and specific gravity. PSL improves some properties of solid wood from which PSL is made.

scholarly journals Growth performance and wood quality of white jabon (Neolamarckia cadamba) progeny testing at Parung Panjang, Bogor, Indonesia

2019 ◽  
Vol 20 (8) ◽  
Author(s):  
Nurul Chaerani ◽  
DEDE J SUDRAJAT ◽  
ISKANDAR Z SIREGAR ◽  
ULFAH J SIREGAR
Keyword(s):  
Specific Gravity ◽  
Moisture Content ◽  
Growth Performance ◽  
Wood Density ◽  
Block Design ◽  
Wood Quality ◽  
Basic Density ◽  
Progeny Testing ◽  
Pilodyn Penetration

Abstract. Chaerani N, Sudrajat DJ, Siregar IZ, Siregar UJ. 2019. Growth performance and wood quality of white jabon (Neolamarckia cadamba) progeny testing at Parung Panjang, Bogor, Indonesia. Biodiversitas 20: 2295-2301. The aim of this study was to evaluate the genetic parameters of growth and wood quality in white jabon progeny test at 54 months old in Parung Panjang, Bogor. The 105 half-sib families obtained from 12 provenances were evaluated in a randomized complete block design with five replications. Wood quality was assessed both in a non-destructive way using a pilodyn and by destructive method using wood sample taker. Results indicated that the mean value ranged from 5.10 to 10.15 m for height, 6.67 to 15.30 cm for diameter, 2.30 to 3.62 cm for pilodyn penetration, 0.66 to 0.82 g/cm3 for wood density, 0.33 to 0.50 for specific gravity, and 66 to 111 % for moisture content, respectively. There were significant differences among 105 families for all traits except moisture content. The high heritability estimate was found for height (0.4-0.69) and basic density (0.27-0.59). Applying 80% selection intensity on diameter and leaving 84 best families in each block will produce a high total genetic gain. Pilodyn penetration had negative correlation with diameter, wood density, and specific gravity.

scholarly journals Study of Changes in Physical Parameters of compost and vermicompost of Eucalyptus leaf litters

2018 ◽  
Vol 4 (1) ◽  
pp. 34-40
Author(s):  
Ritu Nagar ◽  
Anurag Titov ◽  
Praveesh Bhati
Keyword(s):  
Moisture Content ◽  
Leaf Litter ◽  
Initial Temperature ◽  
Cattle Dung ◽  
Physical Parameters ◽  
Physical Factors ◽  
Eudrilus Eugeniae ◽  
Minimum Level ◽  
Metabolic Heat ◽  
Later Phase

Vermicompost and compost of leaf litter of Eucalyptus was studied in plastic bins in duplicate sets with two different proportions (100 % and 50 %). For vermicompost experiments, epigeic earthworm species Eisenia foetida and Eudrilus eugeniae were employed at 10-10 numbers each per vermicompost bins. Cattle dung was taken as control. During the entire process physical factors viz. temperature, pH, moisture content and biomass were measured and compaired. The results were reveal that initial temperature was 35°C ± 2°C in both vermicompost and compost leaf litter and after several weeks, it was set at minimum level. In 50 % leaf litter temperature was 2-3°C higher than 100 % leaf litter. pH of both vermicompost and compost mixtures were acidic in beginning phase while set at alkaline at final stage. Vermicompost had lower pH than compost. Moisture content of leaf litter also decreased in initial phase due to generation of metabolic heat but at later phase it was increased due to decreasing of metabolic heat. More changed was seen in 100 % leaf litter followed by 50 % and then cattle dung. Biomass of leaf litter was more decreased in 100 % waste then 50 % and cattle dung.

scholarly journals Pengaruh Penambahan Abu Arang Tempurung Kelapa Pada Tanah Lempung Terhadap Hasil Uji Kompaksi

2021 ◽  
Vol 3 (2) ◽  
pp. 276-285
Author(s):  
Brigita Suzanna ◽  
Irwan Lie Keng Wong ◽  
Monika Datu Mirring Palinggi
Keyword(s):  
Specific Gravity ◽  
Moisture Content ◽  
Physical Properties ◽  
Clay Soil ◽  
Test Method ◽  
Coconut Shell ◽  
Dry Density ◽  
Coconut Shell Ash ◽  
American Society ◽  
Index Value

The purpose of this research is to determine the physical properties of clay soil and to analyze the effect of adding coconut shell charcoal ash to the clay soil. The soil samples used in this study came from Tanralili District, Maros Regency, two sample points were taken and the variations in the levels of addition of coconut shell charcoal ash is 0%, 4%, 6%, 8%, 10%. The test method used refers to ASTM (American Society for Testing Materials). The tests carried out were testing the physical properties of the soil in the form of moisture content, specific gravity, Atterberg boundaries, filter analysis, and hydrometer analysis, then a compaction test was carried out to determine the maximum soil density. The results of the test obtained a moisture content value of 28.811%, a specific gravity of 2.58 g / cm3 so that it is classified as organic clay. As well as the plasticity index value of 9.926% with moderate plasticity from the 7% -17% interval. Then from the test results of soil compaction testing with the addition of coconut shell ash, the dry density (gdry) equal to 0.862, 0.886, 0.914, 0.943, 0.962, this means that the soil sample experienced an increase in dry density (gdry) of 11.60%. From the research results it can be concluded that the addition of coconut shell charcoal ash can increase the value of soil dry density so that it can be used to increase the value of the carrying capacity of clay soil.

scholarly journals Biodiesel Production and Characterization from Used Vegetable Oil

2021 ◽  
Vol 25 (4) ◽  
pp. 537-542
Author(s):  
C.A. Odega ◽  
G.T. Anguruwa ◽  
C.O. Fakorede
Keyword(s):  
Refractive Index ◽  
Specific Gravity ◽  
Moisture Content ◽  
Cloud Point ◽  
Vegetable Oil ◽  
Positive Impact ◽  
Flash Point ◽  
International Standards ◽  
Biodiesel Production ◽  
Used Vegetable Oil

Biodiesel is a fuel produced from renewable resources; it is a clean alternative fuel, which has drawn the attention of energy researchers for the last two decades due to the disturbing effect of climate change caused by diesel fuel. This paper focuses on showcasing the qualities of biodiesel produced from used vegetable oil and the positive impact on the alarming change in climate today. This paper presents an experimental investigation on production of biodiesel from used vegetable oil (UVO) gotten from a road side bean cake (akara) seller. The oil that was intended to be thrown out was de-odoured and filtered to remove impurities. The filtered oil was then used for biodiesel production and characterized with physical and fuel properties such as density, viscosity, cloud point, refractive index, specific gravity, ash content, moisture content, flash point and cloud point. The results obtained were afterwards compared to ASTM (American Society for Testing and Materials) and EN (Europe’s) international standards. Two biodiesels samples were produced at different temperatures but the same timings. The biodiesel were produced at 700C at 40mins (biodiesel A) and 1000C at 40mins (biodiesel B) with values of specific gravity (0.98 kg/m3; 0.90 kg/m3), density (936kg/m3; 882kg/m3), kinematic viscosity (1.5mm/s2; 5.5 mm/s2), cloud point (150C; 20C), flash point (2600C min; 2000C min), moisture content (0.07%; 0.04%), refractive index (1.4609; 1.4398) and ash point (0.24%; 0.01%) respectively. On comparison, biodiesel A couldn’t match up to the international standards while biodiesel matched up to the standards given.

scholarly journals Physical properties of sessile oak (quercus petraea l) used by the wood industry in Kosovo

2020 ◽  
Vol 2 (7) ◽  
pp. 278-285
Author(s):  
Rrahim Sejdiu ◽  
Florit Hoxha ◽  
Bujar Jashari ◽  
Lulzim Idrizi
Keyword(s):  
Specific Gravity ◽  
Moisture Content ◽  
Physical Properties ◽  
Radial Direction ◽  
Tangential Direction ◽  
Quercus Petraea ◽  
Sessile Oak ◽  
Content Ratio ◽  
Wet Condition ◽  
Shrinkage Coefficient

The paper shows some physical properties of sessile oak obtained in Kosovo regions. In the study are shown: wood shrinkage, specific gravity, shrinkage coefficient for 1% change of moisture content, ratio of shrinkage in tangential and radial direction etc. The amount of volumetric shrinkage of sessile oak is 15.95%, heartwood part has an average shrinkage 15.41% in The shrinkage of sapwood part is 17.56%. Specific gravity at: wet condition: (1.013gr/cm3); 12% (0.853gr/cm3) and 0% (0.826gr/cm3) of moisture content. Specific gravity of heartwood at: wet condition (1.05gr/cm3); 12% (0.88gr/cm3); 0% (0.85gr/cm3). The specific gravity of sapwood at: wet condition (0.91gr/cm3); 12% (0.77gr/cm3); 0% (0.748gr/cm3). The ratio of average shrinkage between tangential and radial cutting direction is 1.71%. This ratio was significantly higher in sapwood than heartwood. Coefficient of shrinkage (changing 1% of moisture content) in the radial direction is 0.00196, and 0.00323 in tangential direction.  

scholarly journals ODREĐIVANJE HEMIJSKOG SASTAVA RAZLIČITIH EKSTRAKATA ČUVARKUĆE

2021 ◽  
Author(s):  
Jelena Mladenovic ◽  
◽  
Nebojsa Markovic ◽  
Ljiljana Boskovic-Rakocevic ◽  
Milena Đuric ◽  
...  
Keyword(s):  
Herbal Medicine ◽  
Vitamin C ◽  
Moisture Content ◽  
Organic Acids ◽  
Skin Diseases ◽  
Aloe Vera ◽  
First Aid ◽  
Wide Range ◽  
Anti Inflammatory

Sempervivum tectorum has a similar effect as aloe vera, which is known in the treatment of various skin diseases. This herb is considered one of the safest remedies for a wide range of skin diseases. Due to its anti-inflammatory and antiseptic properties, it also serves as an excellent first aid for burns, stings and bites, because it provides quick relief and calming. Freshly squeezed juice from the leaves of the houseplant is used in the treatment of nervous disorders, epilepsy and restless dreams. The leaves are edible and can be used as an addition to salads or stews. They are not particularly tasty, but as they are rich in water, they can be put in a juicer together with other fruits or vegetables and become a refreshing drink. It is used in folk herbal medicine and as a medicine. The aim of this study was to determine the moisture content, total extracted substances, extract density, vitamin C, organic acids and proteins in house extracts.

Sign in / Sign up

Export Citation Format

Share Document