scholarly journals Adsorption of Co2+ from Aqueous Solution Using G Low Cost Adsorbent

2020 ◽  
pp. 6-10
Author(s):  
Gharde B. D. ◽  
Gharde A. D.
Keyword(s):  
Heavy Metals ◽  
Metal Ions ◽  
Low Cost ◽  
Packed Column ◽  
Mining Operation ◽  
Tree Bark ◽  
Small Scale ◽  
Batch Adsorption ◽  
Adsorption Studies ◽  
Column Adsorption

Concentration of water supplies with metals is constant area of concern naturally an international. The challenge to remediate hazardous metals containing waste stream from present formal mining operation, industrial sites and ground water is immersed. Adsorption has proved to be an accelerate way to treat industrial waste effluents. The heavy metals renders the water unsuitable for drinking and also higher toxic to human being. Removal of these material is therefore essential. The studies pertaining to the use of inexpensive agro based adsorbents, such as tree bark, saw dust, Corn cob, straw and fly ashes for heavy metals ions has been investigated using Mangifeara indica substrate through batch adsorption studies. Result obtained are quite encouraging, batch adsorption studies have shown that removal of metal ions is dependent upon process parameters like contact time, temperature, metal ions concentration, dosage and pH. The maximum removal of Co2+ to the extent of has been achieved at pH 4 to 6 in 30 min in the concentration range 30 to 90 mg/liter. The use of packed column adsorption has been investigated at the optimum condition, to study the feasibility of the process s for application in small scale industries.

scholarly journals Batch Sorption Experiments: Langmuir and Freundlich Isotherm Studies for the Adsorption of Textile Metal Ions onto Teff Straw (Eragrostis tef) Agricultural Waste

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Mulu Berhe Desta
Keyword(s):  
Heavy Metals ◽  
Metal Ions ◽  
Contact Time ◽  
Metal Ion ◽  
Low Cost ◽  
Agricultural Waste ◽  
Equilibrium Concentration ◽  
Eragrostis Tef ◽  
Batch Adsorption ◽  
Textile Effluents

Adsorption of heavy metals (Cr, Cd, Pb, Ni, and Cu) onto Activated Teff Straw (ATS) has been studied using batch-adsorption techniques. This study was carried out to examine the adsorption capacity of the low-cost adsorbent ATS for the removal of heavy metals from textile effluents. The influence of contact time, pH, Temperature, and adsorbent dose on the adsorption process was also studied. Results revealed that adsorption rate initially increased rapidly, and the optimal removal efficiency was reached within about 1 hour. Further increase in contact time did not show significant change in equilibrium concentration; that is, the adsorption phase reached equilibrium. The adsorption isotherms could be fitted well by the Langmuir model. The value in the present investigation was less than one, indicating that the adsorption of the metal ion onto ATS is favorable. After treatment with ATS the levels of heavy metals were observed to decrease by 88% (Ni), 82.9% (Cd), 81.5% (Cu), 74.5% (Cr), and 68.9% (Pb). Results indicate that the freely abundant, locally available, low-cost adsorbent, Teff straw can be treated as economically viable for the removal of metal ions from textile effluents.

scholarly journals Adsorption Studies of Chromium by Using Low Cost Adsorbents

Our Nature ◽  
2013 ◽  
Vol 11 (1) ◽  
pp. 11-16 ◽  
Author(s):  
N. Gandhi ◽  
D. Sirisha ◽  
K.B. Chandra Sekhar
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Contact Time ◽  
Low Cost ◽  
Water Bodies ◽  
Batch Adsorption ◽  
Toxic Heavy Metals ◽  
Adsorption Studies ◽  
Chromium Vi ◽  
Aqueous Streams

The presence of toxic heavy metals such as chromium (VI) contaminants in aqueous streams, arising from the discharge of untreated metal containing effluents into water bodies, is one of the most important environmental problems. Adsorption is one of the effective techniques for chromium (VI) removal from wastewater. In the present study, adsorbent was prepared from low cost adsorbents and studies were carried out for chromium (VI) removal. Batch adsorption studies demonstrated that the adsorbents had significant capacity to adsorb the chromium from aqueous solution. It was found that the adsorption increased with increase in contact time and adsorbent dosage. An attempt was made to study mixed algae as an adsorbent for removal of chromium (VI).DOI: http://dx.doi.org/10.3126/on.v11i1.8238 Our Nature Vol.11(1) 2013: 11-16?

scholarly journals Kinetics and isotherm modeling of Pb(II) and Cd(II) sequestration from polluted water onto tropical ultisol obtained from Enugu Nigeria

2021 ◽  
Vol 11 (4) ◽  
Author(s):  
Theresa C. Umeh ◽  
John K. Nduka ◽  
Kovo G. Akpomie
Keyword(s):  
Metal Ions ◽  
Low Cost ◽  
Water Environment ◽  
Standard Technique ◽  
Soil Surface ◽  
Cost Effective ◽  
Polluted Water ◽  
Batch Adsorption ◽  
Lead And Cadmium ◽  
Pseudo Second Order

AbstractDeterioration in soil–water environment severely contributed by heavy metal bioavailability and mobility on soil surface and sub-surface due to irrational increase in wastewater discharge and agrochemical activities. Therefore, the feasibility of adsorption characteristics of the soil is paramount in curbing the problem of micropollutant contamination in the farming vicinity. Soil from a farming site in a populated area in Enugu, Nigeria was collected and tested to measure the lead and cadmium contents using atomic absorption spectrophotometer (AAS). The adsorption potency of the ultisol soil was estimated for identifiable physicochemical properties by standard technique. The mean activity concentration of Pb2+ and Cd2+ was 15.68 mg/kg and 3.01 mg/kg. The pH, temperature, metal concentration and contact time adsorptive effect on the Pb2+ and Cd2+ uptake was evaluated by batch adsorption technique. The Langmuir, Freundlich and Temkin models were fitted into equilibrium adsorption data and the calculated results depict a better and satisfactory correlation for Langmuir with higher linear regression coefficients (Pb2+, 0.935 and Cd2+, 0.971). On the basis of sorption capacity mechanism of the soil, pseudo-second-order model best described the kinetics of both metal ions retention process. The results of the present study indicated that the soil being a low cost-effective adsorbent can be utilized to minimize the environmental risk impact of these metal ions.

scholarly journals New Activated Carbon from Mine Coal for Adsorption of Dye in Simulated Water or Multiple Heavy Metals in Real Wastewater

Materials ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2498 ◽  
Author(s):  
Marwa Elkady ◽  
Hassan Shokry ◽  
Hesham Hamad
Keyword(s):  
Activated Carbon ◽  
Nitric Acid ◽  
Metal Ions ◽  
Low Cost ◽  
Dye Adsorption ◽  
Chemical Properties ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Physico Chemical ◽  
Multiple Heavy Metals

Nano-activated carbon (NAC) prepared from El-Maghara mine coal were modified with nitric acid solution. Their physico-chemical properties were investigated in terms of methylene blue (MB) adsorption, FTIR, and metal adsorption. Upon oxidation of the ACS with nitric acid, surface oxide groups were observed in the FTIR spectra by absorption peaks at 1750–1250 cm−1. The optimum processes parameters include HNO3/AC ratio (wt./wt.) of 20, oxidation time of 2 h, and the concentration of HNO3 of 10% reaching the maximum adsorption capacity of MB dye. Also, the prepared NAC was characterized by SEM, EDX, TEM, Raman Spectroscopy, and BET analyses. The batch adsorption of MB dye from solution was used for monitoring the behavior of the most proper produced NAC. Equilibrium isotherms of MB dye adsorption on NAC materials were acquired and the results discussed in relation to their surface chemistry. Langmuir model recorded the best interpretation of the dye adsorption data. Also, NAC was evaluated for simultaneous adsorption of six different metal ions (Fe2+, Ni2+, Mn2+, Pb2+, Cu2+, and Zn2+) that represented contaminates in petrochemical industrial wastewater. The results indicated that the extracted NAC from El-Maghara mine coal is considered as an efficient low-cost adsorbent material for remediation in both basic dyes and metal ions from the polluted solutions.

scholarly journals Pelletized ponderosa pine bark for adsorption of toxic heavy metals from water

BioResources ◽  
2007 ◽  
Vol 2 (1) ◽  
pp. 66-81
Author(s):  
Miyoung Oh ◽  
Mandla A. Tshabalala
Keyword(s):  
Heavy Metals ◽  
Metal Ions ◽  
Adsorption Capacity ◽  
Ponderosa Pine ◽  
Metal Ion ◽  
Value Added ◽  
Freundlich Isotherm ◽  
Toxic Heavy Metals ◽  
Adsorption Affinity ◽  
Column Adsorption

ark flour from ponderosa pine (Pinus ponderosa) was consolidated into pellets using citric acid as cross-linking agent. The pellets were evaluated for removal of toxic heavy metals from synthetic aqueous solutions. When soaked in water, pellets did not leach tannins, and they showed high adsorption capacity for Cu(II), Zn(II), Cd(II), and Ni(II) under both equilibrium and dynamic adsorption conditions. The experimental data for Cd(II) and Zn(II) showed a better fit to the Langmuir than to the Freundlich isotherm. The Cu(II) data best fit the Freundlich isotherm, and the Ni(II) data fitted both Freundlich and Langmuir isotherms equally. According to the Freundlich constant KF, adsorption capacity of pelletized bark for the metal ions in aqueous solution, pH 5.1 ± 0.2, followed the order Cd(II) > Cu(II) > Zn(II) >> Ni(II); according to the Langmuir constant b, adsorption affinity followed the order Cd(II) >> Cu(II) ≈ Zn(II) >> Ni(II). Although data from dynamic column adsorption experiments did not show a good fit to the Thomas kinetic adsorption model, estimates of sorption affinity series of the metal ions on pelletized bark derived from this model were not consistent with the series derived from the Langmuir or Freundlich isotherms and followed the order Cu(II) > Zn(II) ≈ Cd(II) > Ni(II). According to the Thomas kinetic model, the theoretical maximum amounts of metal that can be sorbed on the pelletized bark in a column at influent concentration of ≈10 mg/L and flow rate = 5 mL/min were estimated to be 57, 53, 50, and 27 mg/g for copper, zinc, cadmium, and nickel, respectively. This study demonstrated the potential for converting low-cost bark residues to value-added sorbents using starting materials and chemicals derived from renewable resources. These sorbents can be applied in the removal of toxic heavy metals from waste streams with heavy metal ion concentrations of up to 100 mg/L in the case of Cu(II).

The influence of heavy metals on the production of extracellular polymer substances in the processes of heavy metal ions elimination

2005 ◽  
Vol 52 (10-11) ◽  
pp. 151-156 ◽  
Author(s):  
J. Mikes ◽  
M. Siglova ◽  
A. Cejkova ◽  
J. Masak ◽  
V. Jirku
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Cell Wall ◽  
Metal Ions ◽  
Cell Walls ◽  
Heavy Metal Ions ◽  
Extracellular Polymeric Substances ◽  
Low Cost ◽  
Toxic Heavy Metals ◽  
Metal Interactions

Wastewaters from a chemical industry polluted by heavy metal ions represent a hazard for all living organisms. It can mean danger for ecosystems and human health. New methods are sought alternative to traditional chemical and physical processes. Active elimination process of heavy metals ions provided by living cells, their components and extracellular products represents a potential way of separating toxic heavy metals from industrial wastewaters. While the abilities of bacteria to remove metal ions in solution are extensively used, fungi have been recognized as a promising kind of low-cost adsorbents for removal of heavy-metal ions from aqueous waste sources. Yeasts and fungi differ from each other in their constitution and in their abilities to produce variety of extracellular polymeric substances (EPS) with different mechanisms of metal interactions. The accumulation of Cd(2+), Cr(6+), Pb(2+), Ni(2+) and Zn(2+) by yeasts and their EPS was screened at twelve different yeast species in microcultivation system Bioscreen C and in the shaking Erlenmayer's flasks. This results were compared with the production of yeast EPS and the composition of yeast cell walls. The EPS production was measured during the yeast growth and cell wall composition was studied during the cultivations in the shaking flasks. At the end of the process extracellular polymers and their chemical composition were isolated and amount of bound heavy metals was characterized. The variable composition and the amount of the EPS were found at various yeast strains. It was influenced by various compositions of growth medium and also by various concentrations of heavy metals. It is evident, that the amount of bound heavy metals was different. The work reviews the possibilities of usage of various yeast EPS and components of cell walls in the elimination processes of heavy metal ions. Further the structure and properties of yeasts cell wall and EPS were discussed. The finding of mechanisms mentioned above is necessary to identify the functional groups entered in the metals elimination processes.

scholarly journals Utilization of a Newly Developed Nanomaterial Based on Loading of Biochar with Hematite for the Removal of Cadmium Ions from Aqueous Media

2021 ◽  
Vol 13 (4) ◽  
pp. 2191
Author(s):  
Tunzeel Iqbal ◽  
Shahid Iqbal ◽  
Fozia Batool ◽  
Dimitrios Thomas ◽  
Malik Muhammad Hassnain Iqbal
Keyword(s):  
Metal Ions ◽  
Adsorption Process ◽  
Low Cost ◽  
Aqueous Media ◽  
Freundlich Isotherm ◽  
Batch Adsorption ◽  
Type I ◽  
Process Data ◽  
Desorption Process ◽  
Saccharum Munja

In order to conserve the energy used for remediation of harmful metals from aqueous media, an adsorption process was performed. It is efficient and low-cost method with zero carbon emissions as compared to other methods. A hematite-based novel nanomaterial loaded onto biochar was utilized for the remediation of toxic cadmium metal ions from aqueous media. Saccharum munja has been employed as low-cost feedstock to prepare the biochar. Three adsorbents i.e., raw Saccharum munja (SM), Saccharum munja biochar (SMBC) and hematite-loaded Saccharum munja bichar (HLSMBC) were used in batch adsorption tests to study uptake of metal ions by optimizing the experimental parameters. Experimental data and calculated results revealed maximum sorption efficiency of Cd(II) removal was given by HLSMBC (72 ppm) and SMBC (67.73 ppm) as compared with SM (48.7 ppm). Among adsorption isotherms applied on work best fit for Cd(II) adsorption on SM was found for a Freundlich isotherm with high values of correlation coefficient R2 ≥ 0.9 for all sorbents and constant 1/n values between 0–1. Equilibrium results were evaluated using five different types of errors functions. Thermodynamic studies suggested feasible, spontaneous and endothermic nature of adsorption process, while, the ∆H parameter < 80 kJ/mol indicated physiosorption and positive ∆S values promoted randomness of ions with increase in adsorption process. Data fitted into type I of pseudo second order kinetics having R2 ≥ 0.98 and rate constants K2 (0–1). Desorption process was also performed for storage, conservation and reuse of sorbent and sorbate materials.

scholarly journals Binary adsorption of [Pb(II) + Co(II)] from aqueous solution using thiolated saw dust

2021 ◽  
Author(s):  
Neha Dhiman
Keyword(s):  
Metal Ions ◽  
Low Cost ◽  
Binary Solution ◽  
Pure Component ◽  
Small Scale ◽  
Batch Experiments ◽  
Saw Dust ◽  
Nature Study ◽  
Technology Advancement ◽  
Small Scale Industries

Abstract Technology advancement contributed to an increase in industrial activities, resulting in the introduction of metal ions into water resources at concentrations well above the WHO limits. Heavy metals are highly toxic and carcinogenic; usually occur as multicomponent mixtures in aquatic environment. In present study, batch experiments have been conducted to study the dependence of varying concentration, time, pH and temperature on the uptake of Pb(II) as pure component under equilibrium conditions using thiolated saw dust. Saw dust has been chemically modified with thioglycolic acid and characterised using proximate and FTIR analyses, degree of thiolation has also been determined. To determine the effect of presence of Co(II) ions on the uptake of Pb(II) ions, batch experiments for [Pb(II) + Co(II)] mixture have been carried out for concentration ratios of 1:0, 1:1, 1:2, 1:3, 1:4 of Pb:Co at pH 5 and data has been interpreted using Langmuir competitive isotherm shows that adsorption of Pb(II) has been suppressed by the presence of Co(II) ions in the binary solution, hence the adsorption process is antagonistic in nature. Study also indicates the possibility of simultaneous removal of both metal ions using low cost bioadsorbent, which is economical specially for application in small scale industries.

Zinc removal from aqueous solution using novel adsorbent MISCBA

2016 ◽  
Vol 6 (3) ◽  
pp. 377-388 ◽  
Author(s):  
Ibrahim Umar Salihi ◽  
Shamsul Rahman Muhamed Kutty ◽  
Muhamed Hasnain Isa ◽  
Nasir Aminu
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Metal Ions ◽  
Contact Time ◽  
Adsorption Process ◽  
Negative Impact ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Adsorbent Dosage ◽  
Zinc Removal

Pollution caused by heavy metals has become a serious problem to the environment nowadays. The treatment of wastewater containing heavy metals continues to receive attention because of their toxicity and negative impact on the environment. Recently, various types of adsorbents have been prepared for the uptake of heavy metals from wastewater through the batch adsorption technique. This study focused on the removal of zinc from aqueous solution using microwave incinerated sugarcane bagasse ash (MISCBA). MISCBA was produced using microwave technology. The influence of some parameters such as pH, contact time, initial metal concentration and adsorbent dosage on the removal of zinc was investigated. The competition between H+ and metal ions has affected zinc removal at a low pH value. Optimum conditions for zinc removal were achieved at pH 6.0, contact time 180 min and adsorbent dosage of 10 g/L, respectively. The maximum adsorption capacity for the removal of zinc was found to be 28.6 mg/g. The adsorption process occurred in a multilayered surface of the MISCBA. Chemical reaction was the potential mechanism that regulates the adsorption process. MISCBA can be used as an effective and cheap adsorbent for treatment of wastewater containing zinc metal ions.

scholarly journals HEAVY METALS (Pb+2, Ni+2, Zn+2) REMOVAL FROM WASTEWATER USING LOW COST ADSORBENTS: A REVIEW

2021 ◽  
Vol 25 (Special) ◽  
pp. 3-88-3-96
Author(s):  
Hibatallah J. Shamkhi ◽  
◽  
Tamara K. Hussein ◽  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Metal Ions ◽  
Heavy Metal Ions ◽  
Membrane Separation ◽  
Low Cost ◽  
Chemical Separation ◽  
Skin Contact ◽  
Lead Zinc ◽  
Living Organisms

Pollution with heavy metal ions lead, zinc and nickel resulting from industrial wastewater for various industries such as electroplating industry, batteries, metal refining mines and other factories which discharge into the environment causing damage and pollution to the environment, living organisms, and the majority of heavy metals carcinogenic due to its high toxicity and its containment of dangerous chemicals. Potential danger to human health in all forms by ingestion, inhalation, or skin contact pose by heavy metals ions such as lead, nickel, zinc, and others. To prevent hazards, they must be removed before disposal by different methods such as ion- exchange, chemical separation, filtration, membrane separation, and adsorption. The purpose of this research is to review different low cost adsorbent materials to remove heavy metal ions lead, zinc and nickel from wastewater.

Sign in / Sign up

Export Citation Format

Share Document