scholarly journals The effect of elevated temperature on the lightweight concrete containing waste PET aggregate

2018 ◽  
Vol 6 (3) ◽  
pp. 1-14
Author(s):  
Semiha Akçaözoğlu
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Structural Integrity ◽  
Elevated Temperatures ◽  
Lightweight Concrete ◽  
Physical And Mechanical Properties ◽  
Lightweight Aggregate ◽  
Unit Weight ◽  
Residual Compressive Strength ◽  
Flexural Tensile Strength

In this study, the effect of waste PET as lightweight aggregate (WPLA) replacement with conventional aggregate on the some physical and mechanical properties and residual compressive strength of concrete was investigated. For this purpose, five different mixtures were prepared (the reference mixture and four WPLA mixtures including 30%, 40%, 50% and 60% waste PET aggregate by volume). The fresh and dry unit weights, compressive strengths, flexural-tensile strengths, water absorption and porosity ratios of the mixtures were measured. In addition the specimens exposed to elevated temperatures at 150, 300 and 450 °C and the residual compressive strengths were measured. Test results indicated that the unit weight, compressive strength and flexural-tensile strength of the specimens decreased as the amount of WPLA increased in concrete. After exposing to elevated temperature, WPLA mixtures retained their structural integrity and compressive strengths at 150 °C and 300 °C. However there was a significant decrease in the residual compressive strength values of WPLA mixtures at 450 °C.

Effects of Elevated Temperatures on the Compressive Strength of HFCC

2011 ◽  
Vol 261-263 ◽  
pp. 416-420 ◽  
Author(s):  
Fu Ping Jia ◽  
Heng Lin Lv ◽  
Yi Bing Sun ◽  
Bu Yu Cao ◽  
Shi Ning Ding
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Relative Strength ◽  
Ordinary Concrete ◽  
Residual Compressive Strength ◽  
Fly Ash Concrete ◽  
The Relationship

This paper presents the results of elevated temperatures on the compressive of high fly ash content concrete (HFCC). The specimens were prepared with three different replacements of cement by fly ash 30%, 40% and 50% by mass and the residual compressive strength was tested after exposure to elevated temperature 250, 450, 550 and 650°C and room temperature respectively. The results showed that the compressive strength apparently decreased with the elevated temperature increased. The presence of fly ash was effective for improvement of the relative strength, which was the ratio of residual compressive strength after exposure to elevated temperature and ordinary concrete. The relative compressive strength of fly ash concrete was higher than those of ordinary concrete. Based on the experiments results, the alternating simulation formula to determine the relationship among relative strength, elevated temperature and fly ash replacement is developed by using regression of results, which provides the theoretical basis for the evaluation and repair of HFCC after elevated temperature.

Isothermal Fatigue Behavior and Damage Modeling of a High Temperature Woven PMC

1999 ◽  
Vol 122 (1) ◽  
pp. 62-68 ◽  
Author(s):  
A. L. Gyekenyesi
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Elevated Temperatures ◽  
Fatigue Behavior ◽  
Stiffness Degradation ◽  
Fatigue Properties ◽  
Residual Compressive Strength ◽  
Stiffness Reduction ◽  
Fatigue Damage Accumulation ◽  
Strength Tests

This study focuses on the fully reversed fatigue behavior exhibited by a carbon fiber/polyimide resin woven laminate at room and elevated temperatures. Nondestructive video edge view microscopy and destructive sectioning techniques were used to study the microscopic damage mechanisms that evolved. The elastic stiffness was monitored and recorded throughout the fatigue life of the coupon. In addition, residual compressive strength tests were conducted on fatigue coupons with various degrees of damage as quantified by stiffness reduction. Experimental results indicated that the monotonic tensile properties were only minimally influenced by temperature, while the monotonic compressive and fully reversed fatigue properties displayed greater reductions due to the elevated temperature. The stiffness degradation, as a function of cycles, consisted of three stages; a short-lived high degradation period, a constant degradation rate segment covering the majority of the life, and a final stage demonstrating an increasing rate of degradation up to failure. Concerning the residual compressive strength tests at room and elevated temperatures, the elevated temperature coupons appeared much more sensitive to damage. At elevated temperatures, coupons experienced a much larger loss in compressive strength when compared to room temperature coupons with equivalent damage. The fatigue damage accumulation law proposed for the model incorporates a scalar representation for damage, but admits a multiaxial, anisotropic evolutionary law. The model predicts the current damage (as quantified by residual stiffness) and remnant life of a composite that has undergone a known load at temperature. The damage/life model is dependent on the applied multiaxial stress state as well as temperature. Comparisons between the model and data showed good predictive capabilities concerning stiffness degradation and cycles to failure. [S0742-4795(00)01001-2]

scholarly journals Experimental Research on High Temperature Resistance of Modified Lightweight Concrete after Exposure to Elevated Temperatures

2016 ◽  
Vol 2016 ◽  
pp. 1-6 ◽  
Author(s):  
Ke-cheng He ◽  
Rong-xin Guo ◽  
Qian-min Ma ◽  
Feng Yan ◽  
Zhi-wei Lin ◽  
...  
Keyword(s):  
Compressive Strength ◽  
High Temperature ◽  
Elevated Temperatures ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
Lightweight Aggregate Concrete ◽  
Modification Method ◽  
Superior Mechanical Properties ◽  
Axial Compressive Strength ◽  
Crushed Limestone

In order to improve the spalling resistance of lightweight aggregate concrete at high temperature, two types of modified materials were used to modify clay ceramsite lightweight aggregates by adopting the surface coating modification method. Spalling of the concrete specimens manufactured by using the modified aggregates was observed during a temperature elevation. Mass loss and residual axial compressive strength of the modified concrete specimens after exposure to elevated temperatures were also tested. Concrete specimens consisting of ordinary clay ceramsites and crushed limestone were manufactured as references for comparison. The results showed that the ordinary lightweight concrete specimens and the crushed limestone concrete specimens were completely spalled after exposure to target temperatures above 400°C and 1000°C, respectively, whereas the modified concrete specimens remained intact at 1200°C, at which approximately 25% to 38% of the residual compressive strength was retained. The results indicated that the modified lightweight concrete specimens have exhibited superior mechanical properties and resistance to thermal spalling after exposure to elevated temperatures.

Strength Recovery of Lightweight Concrete under Elevated Temperature

2014 ◽  
Vol 905 ◽  
pp. 300-305
Author(s):  
Salim Barbhuiya ◽  
Tommy Lo ◽  
Shazim Memon ◽  
Hamid Nikraz
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Relative Humidity ◽  
Elevated Temperatures ◽  
Lightweight Concrete ◽  
Curing Conditions ◽  
Strength Recovery ◽  
Curing Methods ◽  
Limited Application ◽  
Water Curing

This research is aimed at investigating the effect of elevated temperature, curing duration and curing methods on the strength recovery of lightweight concrete. Concrete specimens were subjected to elevated temperatures ranging from 300 to 600°C in a controlled heating environment. The specimens were subjected to three types of curing conditions: continuous water curing at 27°C, curing in a relative humidity of 95% at 27°C and curing in water at 60°C for three days and then curing in water at 27°C. The curing duration ranged from 7 to 56 days. The results indicated that the re-curing of concrete for the recovery of compressive strength is most effective in the temperature range from 300 to 500°C. For temperatures outside the range of 300 to 500°C, re-curing was either not effective or had limited application.

COMPRESSIVE STRENGTH EVALUATION OF LIGHTWEIGHT CONCRETE WITH EXPANDED GLASS AGGREGATE BY ULTRASONIC PULSE VELOCITY METHOD

2020 ◽  
Vol 7 (1) ◽  
Author(s):  
Christopher Collins ◽  
Saman Hedjazi
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Normal Weight ◽  
Unit Weight ◽  
Normal Weight Concrete

In the present study, a non-destructive testing method was utilized to assess the mechanical properties of lightweight and normal-weight concrete specimens. The experiment program consisted of more than a hundred concrete specimens with the unit weight ranging from around 850 to 2250 kg/m3. Compressive strength tests were performed at the age of seven and twenty eight days. Ultrasonic Pulse Velocity (UPV) was the NDT that was implemented in this study to investigate the significance of the correlation between UPV and compressive strength of lightweight concrete specimens. Water to cement ratio (w/c), mix designs, aggregate volume, and the amount of normal weight coarse and fine aggregates replaced with lightweight aggregate, are the variables in this work. The lightweight aggregate used in this study, Poraver®, is a product of recycled glass materials. Furthermore, the validity of the current prediction methods in the literature was investigated including comparison between this study and an available expression in the literature on similar materials, for calculation of mechanical properties of lightweight concrete based on pulse velocity. It was observed that the recently developed empirical equation would better predict the compressive strength of lightweight concrete specimens in terms of the pulse velocity.

Isothermal Fatigue Behavior and Damage Modeling of a High Temperature Woven PMC

1998 ◽  
Author(s):  
Andrew L. Gyekenyesi
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Elevated Temperatures ◽  
Fatigue Behavior ◽  
Stiffness Degradation ◽  
Fatigue Properties ◽  
Residual Compressive Strength ◽  
Stiffness Reduction ◽  
Fatigue Damage Accumulation ◽  
Strength Tests

This study focuses on the fully reversed fatigue behavior exhibited by a carbon fiber/polyimide resin woven laminate at room and elevated temperatures. Nondestructive video edge view microscopy and destructive sectioning techniques were used to study the microscopic damage mechanisms that evolved. The elastic stiffness was monitored and recorded throughout the fatigue life of the coupon. In addition, residual compressive strength tests were conducted on fatigue coupons with various degrees of damage as quantified by stiffness reduction. Experimental results indicated that the monotonic tensile properties were only minimally influenced by temperature, while the monotonic compressive and fully reversed fatigue properties displayed greater reductions due to the elevated temperature. The stiffness degradation, as a function of cycles, consisted of three stages; a short-lived high degradation period, a constant degradation rate segment covering the majority of the life, and a final stage demonstrating an increasing rate of degradation up to failure. Concerning the residual compressive strength tests at room and elevated temperatures, the elevated temperature coupons appeared much more sensitive to damage. At elevated temperatures, coupons experienced a much larger loss in compressive strength when compared to room temperature coupons with equivalent damage. The fatigue damage accumulation law proposed for the model incorporates a scalar representation for damage, but admits a multiaxial, anisotropic evolutionary law. The model predicts the current damage (as quantified by residual stiffness) and remnant life of a composite that has undergone a known load at temperature. The damage/life model is dependent on the applied multiaxial stress state as well as temperature. Comparisons between the model and data showed good predictive capabilities concerning stiffness degradation and cycles to failure.

scholarly journals The Effect of Elevated Temperature on the Lightweight Aggregate Concrete

2017 ◽  
Vol 2 (3) ◽  
pp. 193-196
Author(s):  
Rahel Khalid Ibrahim
Keyword(s):  
Elevated Temperature ◽  
Residual Strength ◽  
Elevated Temperatures ◽  
Lightweight Concrete ◽  
Concrete Structures ◽  
Lightweight Aggregate ◽  
Lightweight Aggregate Concrete ◽  
Aggregate Concrete ◽  
Weight Losses ◽  
Before And After

The use of lightweight concrete has become widely spread in concrete structures in the last years. Fire can be considered as a destructive hazard that attack concrete structures. In this research the effect of elevated temperature on lightweight aggregate concretes is studied. For this purpose, 81 cube shaped specimens were prepared from three different lightweight aggregate concrete mixes. After moist curing periods for 3, 7 and28 days, the specimens were subjected to ambient and elevated temperatures of 450⁰C and 650⁰C for 2hrs.The weight of the specimens before and after exposure to elevated temperatures was determined and the residual strength results for the specimens were compared. The results showed that, the elevated temperature induces a decrease in strength and significant weight losses in lightweight aggregate concrete.

scholarly journals Behavior of structural lightweight concrete produced with expanded clay aggregate and after exposure to high temperatures

2021 ◽  
Author(s):  
Rita Nemes ◽  
Mohammed A. Abed ◽  
Ahmed M. Seyam ◽  
Éva Lublóy
Keyword(s):  
Compressive Strength ◽  
High Temperatures ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
Normal Weight ◽  
Residual Compressive Strength ◽  
Concrete Mixtures ◽  
Temperature Exposure ◽  
Compaction Method ◽  
Do So

AbstractThe residual compressive strength of eight lightweight concrete mixtures containing three commercial grading (Liapor HD 5 N, Liapor HD 7 N, and Liapor 8F) of coarse lightweight aggregate (LWA) were determined after to expose at high temperatures. Eight mixes were produced, two by normal weight aggregate and the rest by different types of LWA. The produced concrete was analyzed after high temperature exposure and the effect of using LWA, the type of LWA, and compaction method was studied. To do so, visual inspection, residual compressive strength, crack pattern, spalling, and thermoanalytical analysis were conducted. Generally, it could be concluded that concrete formulations with LWA behave more advantageous up to 500 °C, compared to those with quartz gravel aggregates. Moreover, this study found that an ideal type of LWA to produce structural concrete was Liapor HD 5 N, which was used for producing the mixes L1 and L3.

scholarly journals Effects of carbon nanotubes on expanded glass and silica aerogel based lightweight concrete

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Suman Kumar Adhikary ◽  
Žymantas Rudžionis ◽  
Simona Tučkutė ◽  
Deepankar Kumar Ashish
Keyword(s):  
Carbon Nanotubes ◽  
Compressive Strength ◽  
Silica Aerogel ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
Cementitious Materials ◽  
Lightweight Aggregate Concrete ◽  
Multi Wall Carbon Nanotubes ◽  
Sem Image ◽  
Study Results

AbstractThis study is aimed to investigate the effect of carbon nanotubes on the properties of lightweight aggregate concrete containing expanded glass and silica aerogel. Combinations of expanded glass (55%) and hydrophobic silica aerogel particles (45%) were used as lightweight aggregates. Carbon nanotubes were sonicated in the water with polycarboxylate superplasticizer by ultrasonication energy for 3 min. Study results show that incorporating multi-wall carbon nanotubes significantly influences the compressive strength and microstructural performance of aerogel based lightweight concrete. The addition of carbon nanotubes gained almost 41% improvement in compressive strength. SEM image of lightweight concrete shows a homogeneous dispersal of carbon nanotubes within the concrete structure. SEM image of the composite shows presence of C–S–H gel surrounding the carbon nanotubes, which confirms the cites of nanotubes for the higher growth of C–S–H gel. Besides, agglomeration of carbon nanotubes and the presence of ettringites was observed in the transition zone between the silica aerogel and cementitious materials. Additionally, flowability, water absorption, microscopy, X-ray powder diffraction, and semi-adiabatic calorimetry results were analyzed in this study.

Effects of Loading Percentage of Polyurethane in Lightweight Concrete

2013 ◽  
Vol 357-360 ◽  
pp. 1082-1085 ◽  
Author(s):  
Kamarul Aini Mohd Sari ◽  
Sohif Mat ◽  
Khairiah Haji Badri ◽  
Muhammad Fauzi Mohd Zain
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Lightweight Concrete ◽  
Palm Kernel ◽  
Physical And Mechanical Properties ◽  
Concrete Mixture ◽  
Experimental Program ◽  
Polymer Concrete ◽  
Optimum Level ◽  
Methylene Diphenyl Diisocyanate

An experimental program was performed to obtain the density, compressive strength, and thermal conductivity of palm-based lightweight concrete. Palm-based polyurethane (PU) particles were used as lightweight aggregates in creating concrete systems. Concrete systems contain palm kernel oil-based polyol (PKO-p) reacted with 2,4-methylene diphenyl diisocyanate (MDI). In this study, polymer concrete was improved to achieve the optimum level of PU with the lowest possible density. The PU particles in the concrete mixture comprised of 1% to 5% w/w with density of less than 1800 kg/m3. The PU particles were 5 mm in size. The ratio of PKO-p to MDI was set at 1:1 and the loading of the concrete mixture was set at 3% w/w to produce lightweight concrete. The resulting concrete has excellent compressive strength (17.5 MPa) and thermal conductivity (0.24 W/mK). Results show that the PU particle dosage has the most significant effect on the physical and mechanical properties of concrete.

Sign in / Sign up

Export Citation Format

Share Document