scholarly journals ANALISIS HEAD LOSSES PADA PENSTOCK UNIT III DI PERUM JASA TIRTA II UNIT JASA PEMBANGKIT PLTA IR. H. DJUANDA

Power Plant ◽  
2018 ◽  
Vol 6 (1) ◽  
pp. 19-25
Author(s):  
Redaksi Tim Jurnal
Keyword(s):  
Energy Production ◽  
Power Plants ◽  
High Reliability ◽  
Hydropower Plant ◽  
Working Fluid ◽  
Temperature Changes ◽  
Head Losses ◽  
Total Head ◽  
Labor System ◽  
Load Center

One of the power plants in the labor system is hydropower, which is a power plant by utilizing water resources as its working fluid. In the operation of the hydropower requires high reliability sothat the energy production contuinitas to the load center or to the power system network can be more optimum. One of the components in the hydropower plant is penstock. Closed pipeline, whether it is laminar or turbulent, must have head losses. Head losses on penstock is a phenomenon of losses on the penstock so as to make the head value on the hydropower becomes reduced. At Penstock unit III PLTA Ir. H. Djuanda there are two phenomenon of head losses, namely: head losses major caused by friction penstock against water and minor head losses in the form of bend 900 with radius 4.375 m and 11.3 m from the axis penstock. Temperature changes affect the size of head losses, but they do not significantly affect penstock efficiency. At a temperature of 240C and a flow rate of 5m / s obtained a total head losses of 0606 m so as to make the potential of turbine inlet power down to 31,247 MW or 99.21%.

scholarly journals Generation of Hydro Energy by Using Data Mining Algorithm for Cascaded Hydropower Plant

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 298
Author(s):  
Iram Parvez ◽  
Jianjian Shen ◽  
Ishitaq Hassan ◽  
Nannan Zhang
Keyword(s):  
Data Mining ◽  
Decision Tree ◽  
Energy Production ◽  
Power Plants ◽  
Hydropower Plant ◽  
Data Mining Algorithm ◽  
Decision Tree Algorithm ◽  
Tree Algorithm ◽  
Interaction Detection ◽  
Hydropower Plants

The thirst of the Earth for energy is lurching towards catastrophe in an era of increasing water shortage where most of the power plants are hydroelectric. The hydro-based power systems are facing challenges in determining day-ahead generation schedules of cascaded hydropower plants. The objective of the current study is to find a speedy and practical method for predicting and classifying the future schedules of hydropower plants in order to increase the overall efficiency of energy by utilizing the water of cascaded hydropower plants. This study is significant for water resource planners in the planning and management of reservoirs for generating energy. The proposed method consists of data mining techniques and approaches. The energy production relationship is first determined for upstream and downstream hydropower plants by using multiple linear regression. Then, a cluster analysis is used to find typical generation curves with the help of historical data. The decision tree algorithm C4.5, Iterative Dichotomiser 3-IV, improved C4.5 and Chi-Squared Automatic Interaction Detection are adopted to quickly predict generation schedules, and detailed comparison among different algorithms are made. The decision tree algorithms are solved using SIPINA software. Results show that the C4.5 algorithm is more feasible for rapidly generating the schedules of cascaded hydropower plants. This decision tree algorithm is helpful for the researchers to make fast decisions in order to enhance the energy production of cascaded hydropower plants. The major elements of this paper are challenges and solution of head sensitive hydropower plants, using the decision-making algorithms for producing the generation schedules, and comparing the generation from the proposed method with actual energy production.

"Recent Patents on the Triboelectrostatic Separation of Fly Ash"

2019 ◽  
Vol 13 ◽  
Author(s):  
Haisheng Li ◽  
Wenping Wang ◽  
Yinghua Chen ◽  
Xinxi Zhang ◽  
Chaoyong Li
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
High Efficiency ◽  
Separation Efficiency ◽  
High Reliability ◽  
Operating Conditions ◽  
Security Requirements ◽  
Unburned Carbon ◽  
Efficient Operation ◽  
Triboelectrostatic Separation

Background: The fly ash produced by coal-fired power plants is an industrial waste. The environmental pollution problems caused by fly ash have been widely of public environmental concern. As a waste of recoverable resources, it can be used in the field of building materials, agricultural fertilizers, environmental materials, new materials, etc. Unburned carbon content in fly ash has an influence on the performance of resource reuse products. Therefore, it is the key to remove unburned carbon from fly ash. As a physical method, triboelectrostatic separation technology has been widely used because of obvious advantages, such as high-efficiency, simple process, high reliability, without water resources consumption and secondary pollution. Objective: The related patents of fly ash triboelectrostatic separation had been reviewed. The structural characteristics and working principle of these patents are analyzed in detail. The results can provide some meaningful references for the improvement of separation efficiency and optimal design. Methods: Based on the comparative analysis for the latest patents related to fly ash triboelectrostatic separation, the future development is presented. Results: The patents focused on the charging efficiency and separation efficiency. Studies show that remarkable improvements have been achieved for the fly ash triboelectrostatic separation. Some patents have been used in industrial production. Conclusion: According to the current technology status, the researches related to process optimization and anti-interference ability will be beneficial to overcome the influence of operating conditions and complex environment, and meet system security requirements. The intelligent control can not only ensure the process continuity and stability, but also realize the efficient operation and management automatically. Meanwhile, the researchers should pay more attention to the resource utilization of fly ash processed by triboelectrostatic separation.

scholarly journals Development of a Hydropower Turbine Using Seawater from a Fish Farm

Processes ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 266
Author(s):  
Md Rakibuzzaman ◽  
Sang-Ho Suh ◽  
Hyoung-Ho Kim ◽  
Youngtae Ryu ◽  
Kyung Yup Kim
Keyword(s):  
Power Plants ◽  
Guide Vane ◽  
Cross Flow ◽  
Synchronous Generator ◽  
Fish Farm ◽  
Hydropower Plant ◽  
Fish Farms ◽  
Data Simulation ◽  
Small Hydropower ◽  
Hydropower Plants

Discharge water from fish farms is a clean, renewable, and abundant energy source that has been used to obtain renewable energy via small hydropower plants. Small hydropower plants may be installed at offshore fish farms where suitable water is obtained throughout the year. It is necessary to meet the challenges of developing small hydropower systems, including sustainability and turbine efficiency. The main objective of this study was to investigate the possibility of constructing a small hydropower plant and develop 100 kW class propeller-type turbines in a fish farm with a permanent magnet synchronous generator (PMSG). The turbine was optimized using a computer simulation, and an experiment was conducted to obtain performance data. Simulation results were then validated with experimental results. Results revealed that streamlining the designed shape of the guide vane reduced the flow separation and improved the efficiency of the turbine. Optimizing the shape of the runner vane decreased the flow rate, reducing the water power and increasing the efficiency by about 5.57%. Also, results revealed that tubular or cross-flow turbines could be suitable for use in fish farm power plants, and the generator used should be waterproofed to avoid exposure to seawater.

scholarly journals Changes in Power Plant NOx Emissions over Northwest Greece Using a Data Assimilation Technique

Atmosphere ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 900
Author(s):  
Ioanna Skoulidou ◽  
Maria-Elissavet Koukouli ◽  
Arjo Segers ◽  
Astrid Manders ◽  
Dimitris Balis ◽  
...  
Keyword(s):  
Power Plant ◽  
Data Assimilation ◽  
Energy Production ◽  
Power Plants ◽  
Transport Model ◽  
A Priori ◽  
Filter Method ◽  
Nox Emissions ◽  
A Posteriori ◽  
Data Assimilation Technique

In this work, we investigate the ability of a data assimilation technique and space-borne observations to quantify and monitor changes in nitrogen oxides (NOx) emissions over Northwestern Greece for the summers of 2018 and 2019. In this region, four lignite-burning power plants are located. The data assimilation technique, based on the Ensemble Kalman Filter method, is employed to combine space-borne atmospheric observations from the high spatial resolution Sentinel-5 Precursor (S5P) Tropospheric Monitoring Instrument (TROPOMI) and simulations using the LOTOS-EUROS Chemical Transport model. The Copernicus Atmosphere Monitoring Service-Regional European emissions (CAMS-REG, version 4.2) inventory based on the year 2015 is used as the a priori emissions in the simulations. Surface measurements of nitrogen dioxide (NO2) from air quality stations operating in the region are compared with the model surface NO2 output using either the a priori (base run) or the a posteriori (assimilated run) NOx emissions. Relative to the a priori emissions, the assimilation suggests a strong decrease in concentrations for the station located near the largest power plant, by 80% in 2019 and by 67% in 2018. Concerning the estimated annual a posteriori NOx emissions, it was found that, for the pixels hosting the two largest power plants, the assimilated run results in emissions decreased by ~40–50% for 2018 compared to 2015, whereas a larger decrease, of ~70% for both power plants, was found for 2019, after assimilating the space-born observations. For the same power plants, the European Pollutant Release and Transfer Register (E-PRTR) reports decreased emissions in 2018 and 2019 compared to 2015 (−35% and −38% in 2018, −62% and −72% in 2019), in good agreement with the estimated emissions. We further compare the a posteriori emissions to the reported energy production of the power plants during the summer of 2018 and 2019. Mean decreases of about −35% and−63% in NOx emissions are estimated for the two larger power plants in summer of 2018 and 2019, respectively, which are supported by similar decreases in the reported energy production of the power plants (~−30% and −70%, respectively).

Microcontroller Based Single Axis Intelligent Control Sun Tracker for Parabolic Trough Collectors

2012 ◽  
Vol 562-564 ◽  
pp. 1772-1775
Author(s):  
Shakeel Akram ◽  
Farhan Hameed Malik ◽  
Rui Jin Liao ◽  
Bin Liu ◽  
Tariq Nazir
Keyword(s):  
Energy Efficiency ◽  
Embedded System ◽  
Alternative Energy ◽  
Power Plants ◽  
Tracking System ◽  
Appropriate Technology ◽  
Working Fluid ◽  
The Sun ◽  
Solar Collectors ◽  
Parabolic Trough

Due to the complex design and high costs of production, solar thermal systems have fallen behind in the world of alternative energy systems. Different mechanisms are applied to increase the efficiency of the solar collectors and to reduce the cost. Solar tracking system is the most appropriate technology to increase the efficiency of solar collectors as well as solar power plants by tracking the sun timely. In order to maximize the efficiency of collectors, one needs to keep the reflecting surface of parabolic trough collectors perpendicular to the sun rays. For this purpose microcontroller based real time sun tracker is designed which is controlled by an intelligent algorithm using shadow technique. The aim of the research project is to test the solar-to-thermal energy efficiency by tracking parabolic trough collector (PTC). The energy efficiency is determined by measuring the temperature rise of working fluid as it flows through the receiver of the collector when it is properly focused. The design tracker is also simulated to check its accuracy. The main purpose to design this embedded system is to increase the efficiency and reliability of solar plants by reducing size, complexity and cost of product.

Hybrid Solar-Geothermal Power Generation to Increase the Energy Production From a Binary Geothermal Plant

2011 ◽  
Author(s):  
Giovanni Manente ◽  
Randall Field ◽  
Ronald DiPippo ◽  
Jefferson W. Tester ◽  
Marco Paci ◽  
...  
Keyword(s):  
Power Plant ◽  
Power Output ◽  
Energy Production ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Solar Thermal Energy ◽  
Geothermal Fluid ◽  
Industrial Grade ◽  
Design Values

This article examines how hybridization using solar thermal energy can increase the power output of a geothermal binary power plant that is operating on geothermal fluid conditions that fall short of design values in temperature and flow rate. The power cycle consists of a subcritical organic Rankine cycle using industrial grade isobutane as the working fluid. Each of the power plant units includes two expanders, a vaporizer, a preheater and air-cooled condensers. Aspen Plus was used to model the plant; the model was validated and adjusted by comparing its predictions to data collected during the first year of operation. The model was then run to determine the best strategy for distributing the available geothermal fluid between the two units to optimize the plant for the existing degraded geofluid conditions. Two solar-geothermal hybrid designs were evaluated to assess their ability to increase the power output and the annual energy production relative to the geothermal-only case.

Estimation and Feasibility of Generating Power Using Tidal Energy

2020 ◽  
Author(s):  
Satya Prasad Paruchuru ◽  
Siva Kalyani Koneti ◽  
Deepthi Jammula ◽  
Jashwitha Nuthalapati
Keyword(s):  
Renewable Energy ◽  
Power Plants ◽  
Space Exploration ◽  
Tidal Energy ◽  
Regions Of Interest ◽  
Working Fluid ◽  
Tidal Power ◽  
The Cost

Abstract Capturing the tidal energy is one of the ways of tapping natural and renewable energy which do not involve the cost of working fluid/ fuel. The present work focuses on some of the feasibility aspects of setting up of major tidal power plants along the seacoast. Besides, the present study synergizes on methods of estimating the power-producing capacities in regions along the seacoast. Estimation of power-producing capacities, calendar month-wise, and lunar month-wise gave handy information. Also, the estimation of power-producing capacities of different regions along a location gave clarity on the probable regions of interest for producing power simultaneously. A comparison of the estimates with the details of the literature authenticated the study. A discussion of producing more tidal power in specific locations gave insights into the aspects that may have been ignored in the literature. Geographic restrictions along the local seacoast like identifying the security-sensitive regions rationalized the estimating procedures. The paper includes a discussion of various factors that address the feasibility concerns. The study supposedly helps space exploration too.

scholarly journals Performance analysis of the thermoacoustic refrigerator with the standing wave and air as a working fluid

2018 ◽  
Vol 44 ◽  
pp. 00063 ◽  
Author(s):  
Jakub Kajurek ◽  
Artur Rusowicz
Keyword(s):  
Temperature Difference ◽  
High Reliability ◽  
Power Input ◽  
Acoustic Power ◽  
Operating Frequency ◽  
Working Fluid ◽  
Resonator Length ◽  
Environmental Friendliness ◽  
The Impact ◽  
Thermoacoustic Refrigerator

Thermoacoustic refrigerator is a new and emerging technology capable of transporting heat from a low-temperature source to a high-temperature source by utilizing the acoustic power input. These devices, operating without hazardous refrigerants and owning no moving components, show advantages of high reliability and environmental friendliness. However, simple to fabricate, the designing of thermoacoustic refrigerators is very challenging. This paper illustrates the impact of significant factors on the performance of the thermoacoustic refrigerator which was measured in terms of the temperature difference generated across the stack ends. The experimental device driven by a commercial loudspeaker and air at atmospheric pressure as a working fluid was examined under various resonator length and operating frequencies. The results indicate that appropriate resonator’s length and operating frequency lead to an increase in the temperature difference created across the stack. The maximum values were achieved for operating frequency equalled to 200 and 300 Hz whereas resonator length corresponded to the half-length of the acoustic wave for these frequencies. The results of experiment also confirm that relationship between these parameters is strongly affected by the stack spacing, which in this research was equalled to 0.4 mm.

scholarly journals Solar Tower Power Plants of Molten Salt External Receivers in Algeria: Analysis of Direct Normal Irradiation on Performance

2018 ◽  
Vol 8 (8) ◽  
pp. 1221 ◽  
Author(s):  
Abdelkader Rouibah ◽  
Djamel Benazzouz ◽  
Rahmani Kouider ◽  
Awf Al-Kassir ◽  
Justo García-Sanz-Calcedo ◽  
...  
Keyword(s):  
Power Generation ◽  
Energy Storage ◽  
Thermal Energy ◽  
Greenhouse Effect ◽  
Energy Production ◽  
Power Plants ◽  
Storage Capacity ◽  
Real Data ◽  
Multiple Power ◽  
And Storage

The increase of solar energy production has become a solution to meet the demand of electricity and reduce the greenhouse effect worldwide. This paper aims to determine the performance and viability of direct normal irradiation of three solar tower power plants in Algeria, to be installed in the highlands and the Sahara (Béchar, El Oued, and Djelfa regions). The performance of the plants was obtained through a system advisor model simulator. It used real data gathered from appropriate meteorological files. A relationship between the solar multiple (SM), power generation, and thermal energy storage (TES) hours was observed. The results showed that the optimal heliostat field corresponds to 1.8 SM and 2 TES hours in Béchar, 1.2 SM and 2 TES hours for El Oued, and 1.5 SM and 4 TES hours for Djelfa. This study shows that there is an interesting relationship between the solar multiple, power generation, and storage capacity.

Sign in / Sign up

Export Citation Format

Share Document