scholarly journals SIMULATIONOF THE TEMPERATURE DISTRIBUTION IN A HYDROXYAPATITE LAYER DURING SELECTIVE LASER SINTERING

2019 ◽  
Vol 8 ◽  
pp. 10-18
Author(s):  
Victor Bessmeltsev ◽  
Andrey Ivanov
Keyword(s):  
Field Experiments ◽  
Selective Laser Sintering ◽  
Processing Parameters ◽  
Additive Technologies ◽  
Hydroxyapatite Powder ◽  
Acceptable Range ◽  
Wide Range ◽  
Processing Modes ◽  
Direct Melting ◽  
Better Than

The production of the hydroxyapatite baser bone implants by the direct sintering using laser additive technologies is promising. However, atthe present time, the direct melting of the hydroxyapatite technologies make it possible to obtain the spatial XY resolution not better than 2 mm, while for a real products about 200 µm are required. The production process is characterized by the wide range of parameters, and carrying out field experiments for the selection ofthe processing modes, allowing to increase the resolution, requires a lot of time. In this regard, the numerical model that allows to simulate the process of selective laser melting of the hydroxyapatite powder has been developed and implemented. This model can be applied to determine the acceptable range of the processing parameters.

Selective Laser Sintering of Biomaterials and Composites State of the Art and Perspectives

2020 ◽  
Vol 1012 ◽  
pp. 278-283
Author(s):  
Henrique Schappo ◽  
Lya Piaia ◽  
Dachamir Hotza ◽  
Gean Vitor Salmoria
Keyword(s):  
Review Paper ◽  
Complex Geometry ◽  
State Of The Art ◽  
Complex Structure ◽  
Selective Laser Sintering ◽  
Processing Parameters ◽  
Laser Sintering ◽  
Manufacturing Processes ◽  
Bone Scaffolds ◽  
Wide Range

Human bone has a complex geometry, varying its structure and composition. Additive manufacturing processes, such as selective laser sintering (SLS), can produce bone scaffolds with a wide range of biomaterials. Through SLS a complex structure with highly interconnected porous can be fabricated from a combination of materials. Composites made from biopolymers and bioceramics have shown promising results for bone regeneration, although some properties still must be enhanced. Finding suitable processing parameters is mandatory to achieve required final properties. This review paper is focused on polymer/ceramics using SLS machines in the last 10 years.

Research of the activity and viability of spermatozoa at different concentrations and proportions of diluents after incubation

2020 ◽  
pp. 88-95
Author(s):  
Svitlana Lobchenko ◽  
Tetiana Husar ◽  
Viktor Lobchenko
Keyword(s):  
Plasma Concentration ◽  
Incubation Time ◽  
Coefficient Of Variation ◽  
Incubation Medium ◽  
Wide Range ◽  
Series Of Experiments ◽  
The Subject ◽  
Boar Spermatozoa ◽  
Native Plasma ◽  
Better Than

The results of studies of the viability of spermatozoa with different incubation time at different concentrations and using different diluents are highlighted in the article. (Un) concentrated spermatozoa were diluented: 1) with their native plasma; 2) medium 199; 3) a mixture of equal volumes of plasma and medium 199. The experiment was designed to generate experimental samples with spermatozoa concentrations prepared according to the method, namely: 0.2; 0.1; 0.05; 0.025 billion / ml. The sperm was evaluated after 2, 4, 6 and 8 hours. The perspective of such a study is significant and makes it possible to research various aspects of the subject in a wide range. In this regard, a series of experiments were conducted in this area. The data obtained are statistically processed and allow us to highlight the results that relate to each stage of the study. In particular, in this article it was found out some regularities between the viability of sperm, the type of diluent and the rate of rarefaction, as evidenced by the data presented in the tables. As a result of sperm incubation, the viability of spermatozoa remains at least the highest trend when sperm are diluted to a concentration of 0.1 billion / ml, regardless of the type of diluent used. To maintain the viability of sperm using this concentration of medium 199 is not better than its native plasma, and its mixture with an equal volume of plasma through any length of time incubation of such sperm. Most often it is at this concentration of sperm that their viability is characterized by the lowest coefficient of variation, regardless of the type of diluent used, which may indicate the greatest stability of the result under these conditions. The viability of spermatozoa with a concentration of 0.1 billion / ml is statistically significantly reduced only after 6 or even 8 hours of incubation. If the sperm are incubated for only 2 hours, regardless of the type of diluent used, the sperm concentrations tested do not affect the viability of the sperm. Key words: boar, spermatozoa, sperm plasma, concentration, incubation, medium 199, activity, viability, rarefaction.

Control of Winged Waterprimrose (Jussiaea decurrens) and Northern Jointvetch (Aeschynomene virginica) with Fungal Pathogens

Weed Science ◽  
1979 ◽  
Vol 27 (5) ◽  
pp. 497-501 ◽  
Author(s):  
C. D. Boyette ◽  
G. E. Templeton ◽  
R. J. Smith
Keyword(s):  
Oryza Sativa ◽  
Glycine Max ◽  
Fungal Pathogens ◽  
Liquid Culture ◽  
Field Experiments ◽  
Colletotrichum Gloeosporioides ◽  
Pathogenic Fungus ◽  
Field Tests ◽  
Wide Range ◽  
Growing Region

An indigenous, host-specific, pathogenic fungus that parasitizes winged waterprimrose [Jussiaea decurrens(Walt.) DC.] is endemic in the rice growing region of Arkansas. The fungus was isolated and identified asColletotrichum gloeosporioides(Penz.) Sacc. f.sp. jussiaeae(CGJ). It is highly specific for parasitism of winged waterprimrose and not parasitic on creeping waterprimrose (J. repensL. var.glabrescensKtze.), rice (Oryza sativaL.), soybeans [Glycine max(L.) Merr.], cotton (Gossypium hirsutumL.), or 4 other crops and 13 other weeds. The fungus was physiologically distinct from C.gloeosporioides(Penz.) Sacc. f. sp.aeschynomene(CGA), an endemic anthracnose pathogen of northern jointvetch[Aeschynomene virginica(L.) B.S.P.], as indicated by cross inoculations of both weeds. Culture in the laboratory and inoculation of winged waterprimrose in greenhouse, growth chamber and field experiments indicated that the pathogen was stable, specific, and virulent in a wide range of environments. The pathogen yielded large quantities of spores in liquid culture. It is suitable for control of winged waterprimrose. Winged waterprimrose and northern jointvetch were controlled in greenhouse and field tests by application of spore mixtures of CGJ and CGA at concentrations of 1 to 2 million spores/ml of each fungus in 94 L/ha of water; the fungi did not damage rice or nontarget crops.

Effect of Contact Ratio on Spur Gear Dynamic Load With No Tooth Profile Modifications

1996 ◽  
Vol 118 (3) ◽  
pp. 439-443 ◽  
Author(s):  
Chuen-Huei Liou ◽  
Hsiang Hsi Lin ◽  
F. B. Oswald ◽  
D. P. Townsend
Keyword(s):  
Dynamic Load ◽  
Spur Gear ◽  
Tooth Size ◽  
Contact Ratio ◽  
Gear Dynamics ◽  
Wide Range ◽  
Gear Contact ◽  
Center Distance ◽  
Selection Of ◽  
Better Than

This paper presents a computer simulation showing how the gear contact ratio affects the dynamic load on a spur gear transmission. The contact ratio can be affected by the tooth addendum, the pressure angle, the tooth size (diametral pitch), and the center distance. The analysis presented in this paper was performed by using the NASA gear dynamics code DANST. In the analysis, the contact ratio was varied over the range 1.20 to 2.40 by changing the length of the tooth addendum. In order to simplify the analysis, other parameters related to contact ratio were held constant. The contact ratio was found to have a significant influence on gear dynamics. Over a wide range of operating speeds, a contact ratio close to 2.0 minimized dynamic load. For low-contact-ratio gears (contact ratio less than two), increasing the contact ratio reduced gear dynamic load. For high-contact-ratio gears (contact ratio equal to or greater than 2.0), the selection of contact ratio should take into consideration the intended operating speeds. In general, high-contact-ratio gears minimized dynamic load better than low-contact-ratio gears.

Researches Concerning the Phenomena at the Interface for the Sintered Compacts of Titan-Hydroxyapatite

2013 ◽  
Vol 856 ◽  
pp. 164-168 ◽  
Author(s):  
Diana Irinel Băilă
Keyword(s):  
Specific Surface ◽  
Bone Tissue ◽  
Contact Zone ◽  
Cellular Differentiation ◽  
Selective Laser Sintering ◽  
Important Process ◽  
Sintering Process ◽  
Cellular Processes ◽  
Hydroxyapatite Powder ◽  
Ti Powder

The behaviour of metallic powders is very important for manufacturing parts and for realize the prototypes. Manufacturing of the orthopaedic implants by selective laser sintering process can be used in medicine. The powders necessary for SLS process are biomaterials who must assure a good osteointegration of endobone implants like the Ti powder (Ti-6Al-4V) and the hydroxyapatite powder. The conditioned powders is a very important process and is necessary in SLS to obtain medical prothesis and influence the final properties of prothesis. Materials must present a gradient for porosity and one for composition (presents of a bioactive phase in titan matrix). The exterior porosity, in the contact zones with the bone tissue, favors the incipient cellular processes (the adhesion and attachment of osteoblastes, proliferation and cellular differentiation and nucleation of mineral bone). The pores must be open and with a specific surface more great. Its preferred the exterior intercommunicating porosity. The presence of phosphates of calcium in the contact zone of the implant with bone favors the mineral kernel on bone. The report Ca/P of phosphates mineral bone has an ascending evolution towards 10/6 according to hydroxyapatite.

scholarly journals Performance Evaluation of IMERG GPM Products during Tropical Storm Imelda

Atmosphere ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 687
Author(s):  
Salman Sakib ◽  
Dawit Ghebreyesus ◽  
Hatim O. Sharif
Keyword(s):  
Stage Iv ◽  
Tropical Storm ◽  
Average Correlation ◽  
Acceptable Range ◽  
Precipitation Estimates ◽  
Overall Performance ◽  
Early Late ◽  
Statistical Metrics ◽  
Better Than

Tropical Storm Imelda struck the southeast coastal regions of Texas from 17–19 September, 2019, and delivered precipitation above 500 mm over about 6000 km2. The performance of the three IMERG (Early-, Late-, and Final-run) GPM satellite-based precipitation products was evaluated against Stage-IV radar precipitation estimates. Basic and probabilistic statistical metrics, such as CC, RSME, RBIAS, POD, FAR, CSI, and PSS were employed to assess the performance of the IMERG products. The products captured the event adequately, with a fairly high POD value of 0.9. The best product (Early-run) showed an average correlation coefficient of 0.60. The algorithm used to produce the Final-run improved the quality of the data by removing systematic errors that occurred in the near-real-time products. Less than 5 mm RMSE error was experienced in over three-quarters (ranging from 73% to 76%) of the area by all three IMERG products in estimating the Tropical Storm Imelda. The Early-run product showed a much better RBIAS relatively to the Final-run product. The overall performance was poor, as areas with an acceptable range of RBIAS (i.e., between −10% and 10%) in all the three IMERG products were only 16% to 17% of the total area. Overall, the Early-run product was found to be better than Late- and Final-run.

A multi-shop integrated scheduling algorithm with fixed output constraint

2021 ◽  
pp. 1-9
Author(s):  
Yingchun Xia ◽  
Zhiqiang Xie ◽  
Yu Xin ◽  
Xiaowei Zhang
Keyword(s):  
Constraint Programming ◽  
Programming Model ◽  
Scheduling Algorithm ◽  
Processing Parameters ◽  
Scheduling Problem ◽  
Integrated Scheduling ◽  
Scheduling Scheme ◽  
Wide Range ◽  
Constraint Programming Model ◽  
Output Constraint

The customized products such as electromechanical prototype products are a type of product with research and trial manufacturing characteristics. The BOM structures and processing parameters of the products vary greatly, making it difficult for a single shop to meet such a wide range of processing parameters. For the dynamic and fuzzy manufacturing characteristics of the products, not only the coordinated transport time of multiple shops but also the fact that the product has a designated output shop should be considered. In order to solve such Multi-shop Integrated Scheduling Problem with Fixed Output Constraint (MISP-FOC), a constraint programming model is developed to minimize the total tardiness, and then a Multi-shop Integrated Scheduling Algorithm (MISA) based on EGA (Enhanced Genetic Algorithm) and B&B (Branch and Bound) is proposed. MISA is a hybrid optimization method and consists of four parts. Firstly, to deal with the dynamic and fuzzy manufacturing characteristics, the dynamic production process is transformed into a series of time-continuous static scheduling problem according to the proposed dynamic rescheduling mechanism. Secondly, the pre-scheduling scheme is generated by the EGA at each event moment. Thirdly, the jobs in the pre-scheduling scheme are divided into three parts, namely, dispatched jobs, jobs to be dispatched, and jobs available for rescheduling, and at last, the B&B method is used to optimize the jobs available for rescheduling by utilizing the period when the dispatched jobs are in execution. Google OR-Tools is used to verify the proposed constraint programming model, and the experiment results show that the proposed algorithm is effective and feasible.

scholarly journals Rattail fescue (Vulpia myuros) interference and seed production as affected by sowing time and crop density in winter wheat

Weed Science ◽  
2020 ◽  
pp. 1-10
Author(s):  
Muhammad Javaid Akhter ◽  
Per Kudsk ◽  
Solvejg Kopp Mathiassen ◽  
Bo Melander
Keyword(s):  
Winter Wheat ◽  
Grain Yield ◽  
Seed Production ◽  
Yield Components ◽  
Field Experiments ◽  
Growing Season ◽  
Sowing Time ◽  
Growing Seasons ◽  
Crop Density ◽  
Wide Range

Abstract Field experiments were conducted in the growing seasons of 2017 to 2018 and 2018 to 2019 to evaluate the competitive effects of rattail fescue [Vulpia myuros (L.) C.C. Gmel.] in winter wheat (Triticum aestivum L.) and to assess whether delayed crop sowing and increased crop density influence the emergence, competitiveness, and fecundity of V. myuros. Cumulative emergence showed the potential of V. myuros to emerge rapidly and under a wide range of climatic conditions with no effect of crop density and variable effects of sowing time between the two experiments. Grain yield and yield components were negatively affected by increasing V. myuros density. The relationship between grain yield and V. myuros density was not influenced by sowing time or by crop density, but crop–weed competition was strongly influenced by growing conditions. Due to very different weather conditions, grain yield reductions were lower in the growing season of 2017 to 2018 than in 2018 to 2019, with maximum grain yield losses of 22% and 50% in the two growing seasons, respectively. The yield components, number of crop ears per square meter, and 1,000-kernel weight were affected almost equally, reflecting that V. myuros’s competition with winter wheat occurred both early and late in the growing season. Seed production of V. myuros was suppressed by delaying sowing and increasing crop density. The impacts of delayed sowing and increasing crop density on seed production of V. myuros highlight the potential of these cultural weed control tactics in the long-term management programs of this species.

scholarly journals Cache-efficient sweeping-based interval joins for extended Allen relation predicates

2021 ◽  
Author(s):  
Danila Piatov ◽  
Sven Helmer ◽  
Anton Dignös ◽  
Fabio Persia
Keyword(s):  
Data Structure ◽  
Experimental Evaluation ◽  
State Of The Art ◽  
Temporal Databases ◽  
Access Method ◽  
Wide Range ◽  
Interval Relation ◽  
Cache Efficient ◽  
Join Algorithms ◽  
Better Than

AbstractWe develop a family of efficient plane-sweeping interval join algorithms for evaluating a wide range of interval predicates such as Allen’s relationships and parameterized relationships. Our technique is based on a framework, components of which can be flexibly combined in different manners to support the required interval relation. In temporal databases, our algorithms can exploit a well-known and flexible access method, the Timeline Index, thus expanding the set of operations it supports even further. Additionally, employing a compact data structure, the gapless hash map, we utilize the CPU cache efficiently. In an experimental evaluation, we show that our approach is several times faster and scales better than state-of-the-art techniques, while being much better suited for real-time event processing.

Triazole, Benzotriazole, and Naphthotriazole as Corrosion Inhibitors for Brass

CORROSION ◽  
1976 ◽  
Vol 32 (10) ◽  
pp. 414-417 ◽  
Author(s):  
R. WALKER
Keyword(s):  
Corrosion Inhibitors ◽  
Lower Cost ◽  
Solution Ph ◽  
Inhibitor Efficiency ◽  
Wide Range ◽  
Better Than

Abstract The use of triazole, benzotriazole, and naphthotriazole as corrosion inhibitors for brass is briefly reviewed. The corrosion of 70/30 brass immersed in a wide range of solutions is reported both with and without the inhibitors. The inhibitor efficiency of benzotriazole is given as a function of the solution pH and the concentration used. Triazole was only effective in mildly corrosive solutions and benzotriazole and naphthotriazole were much better. Generally naphthotriazole was better than benzotriazole but is much more expensive and a higher concentration of benzotriazole can give the same protection as naphthotriazole at a much lower cost.

Sign in / Sign up

Export Citation Format

Share Document