scholarly journals Assessment of Direct Injected Liquefied Petroleum Gas-Diesel Blends for Ultra-Low Soot Combustion Engine Application

2020 ◽  
Vol 10 (14) ◽  
pp. 4949
Author(s):  
Roberto Ianniello ◽  
Gabriele Di Blasio ◽  
Renato Marialto ◽  
Carlo Beatrice ◽  
Massimo Cardone
Keyword(s):  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
High Efficiency ◽  
Combustion Engine ◽  
Combustion Process ◽  
Experimental Tests ◽  
Liquefied Petroleum Gas ◽  
Ambient Conditions ◽  
Promising Alternative ◽  
Compression Ignition Engines

Technological and economic concerns correlated to fulfilling future emissions and CO2 standards require great research efforts to define an alternative solution for low emissions and highly efficient propulsion systems. Alternative fuel formulation could contribute to this aim. Liquefied petroleum gas (LPG) with lower carbon content than other fossil fuels and which is easily vaporized at ambient conditions has the advantage of lowering CO2 emissions and optimizing the combustion process. Liquefied petroleum gas characteristics and availability makes the fuel a promising alternative for internal combustion engines. The possible combination of using it in high-efficiency compression ignition engines makes it worth analyzing the innovative method of using LPG as a blend component in diesel. Few relevant studies are detectable in literature in this regard. In this study, two blends containing diesel and LPG, in volume ratios 20/80 and 35/65, respectively, were formulated and utilized. Their effects on combustion and emissions performance were assessed by performing proper experimental tests on a modern light-duty single-cylinder engine test rig. Reference operating points at conventional engine calibration settings were examined. A specific exhaust gas recirculation (EGR) parametrization was performed evaluating the LPG blends’ potential in reducing the smoke emissions at standard engine-out NOx levels. The results confirm excellent NOx-smoke trade-off improvements with smoke reductions up to 95% at similar NOx and efficiency. Unburnt emissions slightly increase, and to acceptable levels. Improvements, in terms of indicated specific fuel consumption (ISFC), are detected in the range of 1–3%, as well as the CO2 decrease proportionally to the mixing ratio.

Emissions Control From IC Engines Using Advanced Combustion Chamber Design

1993 ◽  
Author(s):  
Jiang Lu ◽  
Ashwani K. Gupta ◽  
Eugene L. Keating ◽  
Andrew A. Pouring
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
High Efficiency ◽  
Combustion Engine ◽  
Effective Means ◽  
Combustion Process ◽  
Cost Effective ◽  
Internal Combustion ◽  
Geometry Design ◽  
Pollutants Emission

Abstract Numerical simulation of flow, combustion phenomena and pollutants emission characteristics have been obtained on an homogeneous-charged internal combustion engine having conventional flat piston and five other bowl-in-piston geometries. The code employed here uses the time marching procedure and solves the governing partial differential equations of multi-component chemically reactive flow by finite difference method. The transient solution is marched out in a sequence of time steps. The results show that the piston geometry affects the local flame properties which subsequently influences the pollutants emission level. The numerical results provide a cost effective means of developing advanced internal combustion engine chamber geometry design that provides high efficiency and low pollution. It is expected that increased computational tools will be used in the future for enhancing our understanding of the detailed combustion process in internal combustion engines and all other energy conversion systems. Such detailed information is critical for the development of advanced methods for energy conservation and environmental pollution control.

Piston Geometry Design Effects on Combustion and Emission Characteristics

1991 ◽  
Author(s):  
Ashwani K. Gupta ◽  
Lu Jiang ◽  
Eugene L. Keating
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
High Efficiency ◽  
Combustion Engine ◽  
Effective Means ◽  
Combustion Process ◽  
Internal Combustion ◽  
Emission Characteristics ◽  
Geometry Design ◽  
Pollutants Emission

Abstract Numerical simulation of flow, combustion phenomena and pollutants emission characteristics have been obtained on an internal combustion engine having conventional flat piston and advanced piston geometries. The code employed the time marching procedure that solves the governing partial differential equations of multi-component chemically reactive fluid flow by finite difference method. The transient solution is marched out in a sequence of time steps. The results show that both the piston geometry and inlet flow conditions affects the local flame properties which subsequently alters the pollutants emission levels. The numerical results provide a cost effective means of developing advanced internal combustion engine chamber geometry design that provides high efficiency and low pollution levels. It is expected that increased computational tools will be used in the future for enhancing our understanding of the detailed combustion process in internal combustion engines and all other energy conversion systems. Such detailed information is critical for energy conservation and environmental pollution control.

Study of Combustion Anomalies of H2-ICE With External Mixture Formation

2006 ◽  
Author(s):  
Stephen A. Ciatti ◽  
Thomas Wallner ◽  
Henry Ng ◽  
William F. Stockhausen ◽  
Brad Boyer
Keyword(s):  
Internal Combustion Engines ◽  
Large Scale ◽  
High Efficiency ◽  
Combustion Engine ◽  
Direct Injection ◽  
Combustion Process ◽  
Engine Performance ◽  
Internal Combustion ◽  
Hydrogen Combustion ◽  
Mixture Formation

Although hydrogen is considered one of the most promising future energy carriers, there are several challenges to achieving a “hydrogen economy,” including finding a practical, efficient, cost-effective end-use device. Using hydrogen as a fuel for internal combustion engines is seen as a bridging technology toward a large-scale hydrogen infrastructure. To facilitate high-efficiency, high-power-density use of hydrogen with near-zero emissions in an internal combustion engine, detailed analysis of the hydrogen combustion process is necessary. This paper presents thermodynamic results regarding engine performance and emissions behavior during investigations performed on a single-cylinder research engine fueled by pressurized gaseous hydrogen. Avoiding combustion anomalies is one of the necessary steps to further improve the hydrogen engine power output at high-load operation while, at the same time, reducing fuel consumption and emissions during part-load operation. The overall target of the investigations is an improved combustion concept especially designed for hydrogen-engine-powered vehicles. Future activities include performing optical imaging of hydrogen combustion by using an endoscope. We will also investigate supercharged external mixture formation, as well as hydrogen direct-injection operation.

Extraction and Determination of Physico-chemical Properties of Oil from Watermelon Seeds (Citrullus lanatus L) to Use in Internal Combustion Engines

2017 ◽  
Vol 68 (11) ◽  
pp. 2676-2681
Author(s):  
Mihaela Gabriela Dumitru ◽  
Dragos Tutunea
Keyword(s):  
Fatty Acid ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Citrullus Lanatus ◽  
Combustion Process ◽  
Chemical Properties ◽  
Physico Chemical ◽  
Mean Diameter ◽  
Geometrical Mean ◽  
Reduction Of Nox

The purpose of this work was to investigate the physicochemical properties of watermelon seeds and oil and to find out if this oil is suitable and compatible with diesel engines. The results showed that the watermelon seeds had the maximum length (9.08 mm), width (5.71mm), thickness (2.0 mm), arithmetic mean diameter (5.59 mm), geometrical mean diameter (4.69 mm), sphericity (51.6%), surface area (69.07), volume 0.17 cm3 and moisture content 5.4%. The oil was liquid at room temperature, with a density and refractive index of 0.945 and 1.4731 respectively acidity value (1.9 mgNaOH/g), free fatty acid (0.95 mgNaOH), iodine value (120 mgI2/100g), saponification value (180 mgKOH/g), antiradical activity (46%), peroxide value (7.5 mEqO2/Kg), induction period (6.2 h), fatty acid: palmitic acid (13.1%), stearic acid (9.5 %), oleic acid (15.2 %) and linoleic acid (61.3%). Straight non food vegetable oils can offer a solution to fossil fuels by a cleaner burning with minimal adaptation of the engine. A single cylinder air cooled diesel engine Ruggerini RY 50 was used to measure emissions of various blends of watermelon oil (WO) and diesel fuel (WO10D90, WO20D80, WO30D70 and WO75D25). The physic-chemical properties of the oil influence the combustion process and emissions leading to the reduction of NOX and the increase in CO, CO2 and HC.

scholarly journals Laminar Burning Velocity of Biogas-Containing Mixtures. A Literature Review

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 996
Author(s):  
Venera Giurcan ◽  
Codina Movileanu ◽  
Adina Magdalena Musuc ◽  
Maria Mitu
Keyword(s):  
Gas Turbines ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Combustion Engine ◽  
Burning Velocity ◽  
Internal Combustion ◽  
Electricity Production ◽  
Engine Fuel ◽  
Laminar Burning Velocity ◽  
Waste Products

Currently, the use of fossil fuels is very high and existing nature reserves are rapidly depleted. Therefore, researchers are turning their attention to find renewable fuels that have a low impact on the environment, to replace these fossil fuels. Biogas is a low-cost alternative, sustainable, renewable fuel existing worldwide. It can be produced by decomposition of vegetation or waste products of human and animal biological activity. This process is performed by microorganisms (such as methanogens and sulfate-reducing bacteria) by anaerobic digestion. Biogas can serve as a basis for heat and electricity production used for domestic heating and cooking. It can be also used to feed internal combustion engines, gas turbines, fuel cells, or cogeneration systems. In this paper, a comprehensive literature study regarding the laminar burning velocity of biogas-containing mixtures is presented. This study aims to characterize the use of biogas as IC (internal combustion) engine fuel, and to develop efficient safety recommendations and to predict and reduce the risk of fires and accidental explosions caused by biogas.

Effect of Engine Operating Parameters on Combustion and Emission Characteristics

1992 ◽  
Author(s):  
Jiang Lu ◽  
Ashwani K. Gupta ◽  
Eugene L. Keating
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Internal Combustion ◽  
Operating Parameters ◽  
Emission Characteristics ◽  
Pollutants Emission

Abstract Numerical simulation of flow, combustion, heat release rate and pollutants emission characteristics have been obtained using a single cylinder internal combustion engine operating with propane as the fuel. The data are compared with experimental results and show excellent agreement for peak pressure and the rate of pressure rise as a function of crank angle. The results obtained for NO and CO are also found to be in good agreement and are similar to those reported in the literature for the chosen combustion chamber geometry. The results have shown that both the combustion chamber geometry and engine operating parameters affects the flame growth within the combustion chamber which subsequently affects the pollutants emission levels. The code employed the time marching procedure and solves the governing partial differential equations of multi-component chemically reacting fluid flow by finite difference method. The numerical results provide a cost effective means of developing advanced internal combustion engine chamber geometry design that provides high efficiency and low pollution levels. It is expected that increased computational tools will be used in the future for enhancing our understanding of the detailed combustion process in internal combustion engines and all other energy conversion systems. Such detailed information is critical for the development of advanced methods for energy conservation and environmental pollution control.

scholarly journals Possibilities of Energy Harvesting from the Suspension System of the Internal Combustion Engine in a Vehicle

2021 ◽  
Vol 23 (2) ◽  
pp. B106-B116
Author(s):  
Jacek Caban ◽  
Grzegorz Litak ◽  
Bartłomiej Ambrożkiewicz ◽  
Leszek Gardyński ◽  
Paweł Stączek ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Power Supply ◽  
Fossil Fuels ◽  
Combustion Engine ◽  
Electric Energy ◽  
Elastic Beam ◽  
Experimental Tests ◽  
Suspension System ◽  
Piezoelectric Energy ◽  
Mechanic Energy

The automotive industry faces huge challenge in environmental protection by reducing fossil fuels and energy consumption by developing various practical solutions in energy harvesting. The current analysis is related to the diesel engine power supply system in a passenger off-road vehicle for application of the piezoelectric energy harvesting system. Experimental tests were carried out for the three constant rotational speed values - 800, 1000 and 1500 rpm. The results pertained to operational and simulation tests of available power supply options from the engine suspension system in the vehicle, e.g. to power sensors supervising the engine’s operation or other small electrical devices in the vehicle. The simulations of output voltage were conducted by means of a nonlinear model with a resonator coupled to a piezoelectric elastic beam deformed in the magnetic field to improve the band of frequency transducing kinetic mechanic energy into electric energy.

scholarly journals Assessment of thermodynamic cycle of internal combustion engine in terms of rightsizing

2019 ◽  
Vol 178 (3) ◽  
pp. 182-186
Author(s):  
Zbigniew SROKA ◽  
Maciej DWORACZYŃSKI
Keyword(s):  
Internal Combustion Engine ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Thermodynamic Cycle ◽  
Internal Combustion ◽  
Research Problem ◽  
Combustion Engines ◽  
Operating Characteristics ◽  
Swept Volume

The modification of the downsizing trend of internal combustion engines towards rightsizing is a new challenge for constructors. The change in the displacement volume of internal combustion engines accompanying the rightsizing idea may in fact mean a reduction or increase of the defining swept volume change factors and thus may affect the change in the operating characteristics as a result of changes in combustion process parameters - a research problem described in this publication. Incidents of changes in the displacement volume were considered along with the change of the compression space and at the change of the geometric degree of compression. The new form of the mathematical dependence describing the efficiency of the thermodynamic cycle makes it possible to evaluate the opera-tion indicators of the internal combustion engine along with the implementation of the rightsizing idea. The work demonstrated the in-variance of cycle efficiency with different forms of rightsizing.

scholarly journals Impact of Simulated Biogas Compositions (CH4 and CO2) on Vibration, Sound Pressure and Performance of a Spark Ignition Engine

Energies ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 7037
Author(s):  
Donatas Kriaučiūnas ◽  
Tadas Žvirblis ◽  
Kristina Kilikevičienė ◽  
Artūras Kilikevičius ◽  
Jonas Matijošius ◽  
...  
Keyword(s):  
Energy Efficiency ◽  
Negative Correlation ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Sound Pressure ◽  
Raw Materials ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Positive Correlation

Biogas has increasingly been used as an alternative to fossil fuels in the world due to a number of factors, including the availability of raw materials, extensive resources, relatively cheap production and sufficient energy efficiency in internal combustion engines. Tightening environmental and renewable energy requirements create excellent prospects for biogas (BG) as a fuel. A study was conducted on a 1.6-L spark ignition (SI) engine (HR16DE), testing simulated biogas with different methane and carbon dioxide contents (100CH4, 80CH4_20CO2, 60CH4_40CO2, and 50CH4_50CO2) as fuel. The rate of heat release (ROHR) was calculated for each fuel. Vibration acceleration time, sound pressure and spectrum characteristics were also analyzed. The results of the study revealed which vibration of the engine correlates with combustion intensity, which is directly related to the main measure of engine energy efficiency—break thermal efficiency (BTE). Increasing vibrations have a negative correlation with carbon monoxide (CO) and hydrocarbon (HC) emissions, but a positive correlation with nitrogen oxide (NOx) emissions. Sound pressure also relates to the combustion process, but, in contrast to vibration, had a negative correlation with BTE and NOx, and a positive correlation with emissions of incomplete combustion products (CO, HC).

A comprehensive evaluation of water injection in the diesel engine

2021 ◽  
pp. 146808742110442
Author(s):  
Sebastian Welscher ◽  
Mohammad Hossein Moradi ◽  
Antonino Vacca ◽  
Peter Bloch ◽  
Michael Grill ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Internal Combustion Engines ◽  
Comprehensive Evaluation ◽  
Combustion Engine ◽  
Water Injection ◽  
Combustion Process ◽  
Internal Combustion ◽  
Exhaust Emission ◽  
Pressure Trace ◽  
High Level

Due to increasing climate awareness and the introduction of much stricter exhaust emission legislation the internal combustion engine technology faces major challenges. Although the development and state of technology of internal combustion engines generally reached a very high level over the last years those need to be improved even more. Combining water injection with a diesel engine, therefore, seems to be the next logical step in developing a highly efficient drive train for future mobility. To investigate these potentials, a comprehensive evaluation of water injection on the diesel engine was carried out. This study covers >560 individual operating points on the test bench. The tests were carried out on a single-cylinder derived from a Euro 6d four-cylinder passenger car with the port water injection. Furthermore, a detailed pressure trace analysis (PTA) was performed to evaluate various aspects regarding combustion, emission, etc. The results show no significant effects of water injection on the combustion process, but great potential for NOx reduction. It has been shown that with the use of water injection at water-to-fuel rates of 25%, 50%, and 100%, NOx reduction without deterioration of soot levels can be achieved in 62%, 40%, and 20% of the experiments, respectively. Furthermore, water injection in combination with EGR offers additional reduction in NOx emissions.

Sign in / Sign up

Export Citation Format

Share Document