scholarly journals Response of Mechanical Properties of Polyvinyl Chloride Geomembrane to Ambient Temperature in Axial Tension

2021 ◽  
Vol 11 (22) ◽  
pp. 10864
Author(s):  
Xianlei Zhang ◽  
Zhongyang Ma ◽  
Yunyun Wu ◽  
Jianqun Liu
Keyword(s):  
Mechanical Properties ◽  
Theoretical Analysis ◽  
Ambient Temperature ◽  
Young’S Modulus ◽  
Polyvinyl Chloride ◽  
Young's Modulus ◽  
Axial Tension ◽  
Single Temperature ◽  
Boltzmann Function ◽  
The Difference

Aiming at the mechanical response of geomembrane (GEM) in membrane-faced rockfill dam (MFRD) to different ambient temperatures, the mechanical properties in axial tension of polyvinyl chloride (PVC) GEM were studied by experiment and theoretical analysis. First, fifteen groups of axial tensile tests for longitudinal/transverse specimens were conducted at different temperatures in the temperature environment laboratory, the stress–strain curve and Young’s modulus were obtained, and the variation of Young’s modulus with temperature was analyzed by Boltzmann function fitting. Second, the glass transition temperature of PVC GEM was obtained by differential scanning calorimetry (DSC), and the difference in mechanical properties between longitudinal and transverse specimens of PVC GEM was analyzed by thermomechanical analyzer (TMA) thermodynamic test. The results showed that the lower the temperature, the greater the Young’s modulus, and the smaller the linear interval of stress and strain, while the higher the temperature, the result is opposite. The difference in mechanical properties between the two directions is related to the ambient temperature. The orientation of polymer structure accounts for the difference in mechanical properties by theoretical analysis. The fitting results of Boltzmann function have a certain reference value for numerical simulation. In design of the membrane impervious structure in MFRD, the ambient temperature should be considered fully, and the longitudinal/transverse welding splicing should be avoided as far as possible. The current test specification should test the mechanical performance of GEM at normal operating temperature of reservoir instead of the test and quality evaluation at a single temperature. The temperature should be considered comprehensively in construction to avoid damaging the performance of impervious structure and ensure the service life.

High Temperature Mechanical Properties of Ni-YSZ Cermets for SOFC Anode

2010 ◽  
Author(s):  
Fumitada Iguchi ◽  
Hiromichi Kitahara ◽  
Hiroo Yugami
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Strain Diagram ◽  
Thermal Cycles ◽  
High Temperature Mechanical Properties ◽  
Sofc Anode ◽  
The Difference

The mechanical properties of Ni-YSZ cermets at high temperature in reduction atmosphere were evaluated by the four points bending method. We studied the influences of reduction and thermal cycles, i.e. a cycle from R.T. to 800°C, to flexural strength and Young’s modulus. The flexural strength of Ni-YSZ at room temperature was lower than that of NiO-YSZ by about 10 to 20% mainly caused by the increment of porosity. But, the flexural strength of Ni-YSZ at 800°C was drastically decreased by an half of that at R.T. In addition, the stress–strain diagram of Ni-YSZ at 800°C indicated that it showed weak ductility. The maximum observed strain was over 0.5% at 30MPa. On the contrary, NiO-YSZ showed only brittlely at 800°C. The difference was caused by Ni metal in the Ni-YSZ cermets. Therefore, it was expected that Ni-YSZ is easily deformed in operation, though residual stress between an anode and an electrolyte was low. The influence of thermal cycles to flexural strength and Young’s modulus was not observed clearly. At the same time, the differences of microstructure were not observed. Therefore, it was concluded that the cycle does not change mechanical properties significantly.

Nanoindentation Characterization of Mechanical Properties of Ferrite and Austenite in Duplex Stainless Steel

2007 ◽  
Vol 26-28 ◽  
pp. 1165-1170 ◽  
Author(s):  
Xiu Fang Wang ◽  
Xiao Ping Yang ◽  
Zhen Dan Guo ◽  
Yin Chang Zhou ◽  
Hong Wei Song
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Hot Forging ◽  
Sample Surface ◽  
Cast Sample ◽  
The Difference

The mechanical properties of as-cast and hot-forging duplex stainless steel samples with the same compositions were characterized by nanoindentation. The effect of surface treating method and working state of the sample on the nanoindentation results of ferrite and austenite were discussed. The results show that the Young’s modulus and hardness of ferrite and austenite may be affected by the treating method of sample surface. The difference of Young’s modulus average of ferrite or austenite between as-cast and hot-forging duplex stainless steel samples is not great, but the hardness average of ferrite or austenite in hot-forging sample is obviously higher than those of as-cast sample. The difference of hardness between ferrite and austenite in the same sample is not great, but the young’s modulus of ferrite is higher than that of austenite.

scholarly journals Evaluation of Mechanical Properties of a Hollow Endodontic Post by Three Point Test and SEM Analysis: A Pilot Study

Materials ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 1983
Author(s):  
Giuseppe Lo Giudice ◽  
Edoardo Ferrari Cagidiaco ◽  
Roberto Lo Giudice ◽  
Francesco Puleio ◽  
Fabiana Nicita ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Fracture Load ◽  
Resin Cement ◽  
Control Group ◽  
Point Test ◽  
The Difference ◽  
Group 1

The aim of this study was to investigate the mechanical properties of a fiber hollow endodontic post characterized by the presence of an empty central cylindrical channel extended along the whole length. This particular shape allows clinicians to use the post also as a cementation resin carrier. Ten hollow posts were divided in two groups: the control group (unfilled hollow posts) (Group 0) and hollow posts filled with dual resin cement (Group 1). The samples of both groups were subjected to mechanical and micromorphological analysis by performing a three-point test and SEM observations. In the three-point test, the Group 1 samples exhibited a fracture load of 57.09 ± 5.06 N, a flexural strength of 1323.53 ± 110.09 MPa, and a Young’s modulus of 42.87 ± 0.86 GPa. The samples of Group 2 exhibited a fracture load of 38.17 ± 1.7 N, a flexural strength of 908.87 ± 30.98 MPa, and a Young’s modulus of 40.33 ± 1.9 GPa. The difference between fracture load, flexural strength, and deflection between the two groups was statistically highly significant (p < 0.01). Further, the difference between the Young’s modulus of the two groups was statistically significant (p < 0.05). The values obtained are similar to those of other posts available on the market.

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

scholarly journals First principles computation of composition dependent elastic constants of omega in titanium alloys: implications on mechanical behavior

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
R. Salloom ◽  
S. A. Mantri ◽  
R. Banerjee ◽  
S. G. Srinivasan
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
First Principles ◽  
Young's Modulus ◽  
Group Vi ◽  
Group V ◽  
Β Phase ◽  
Ti Alloys ◽  
Ω Phase ◽  
Stabilizer Concentration

AbstractFor decades the poor mechanical properties of Ti alloys were attributed to the intrinsic brittleness of the hexagonal ω-phase that has fewer than 5-independent slip systems. We contradict this conventional wisdom by coupling first-principles and cluster expansion calculations with experiments. We show that the elastic properties of the ω-phase can be systematically varied as a function of its composition to enhance both the ductility and strength of the Ti-alloy. Studies with five prototypical β-stabilizer solutes (Nb, Ta, V, Mo, and W) show that increasing β-stabilizer concentration destabilizes the ω-phase, in agreement with experiments. The Young’s modulus of ω-phase also decreased at larger concentration of β-stabilizers. Within the region of ω-phase stability, addition of Nb, Ta, and V (Group-V elements) decreased Young’s modulus more steeply compared to Mo and W (Group-VI elements) additions. The higher values of Young’s modulus of Ti–W and Ti–Mo binaries is related to the stronger stabilization of ω-phase due to the higher number of valence electrons. Density of states (DOS) calculations also revealed a stronger covalent bonding in the ω-phase compared to a metallic bonding in β-phase, and indicate that alloying is a promising route to enhance the ω-phase’s ductility. Overall, the mechanical properties of ω-phase predicted by our calculations agree well with the available experiments. Importantly, our study reveals that ω precipitates are not intrinsically embrittling and detrimental, and that we can create Ti-alloys with both good ductility and strength by tailoring ω precipitates' composition instead of completely eliminating them.

scholarly journals Tailoring a Low Young Modulus for a Beta Titanium Alloy by Combining Severe Plastic Deformation with Solution Treatment

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3467
Author(s):  
Anna Nocivin ◽  
Doina Raducanu ◽  
Bogdan Vasile ◽  
Corneliu Trisca-Rusu ◽  
Elisabeta Mirela Cojocaru ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Young Modulus ◽  
Orthopedic Implants ◽  
Beta Titanium Alloy

The present paper analyzed the microstructural characteristics and the mechanical properties of a Ti–Nb–Zr–Fe–O alloy of β-Ti type obtained by combining severe plastic deformation (SPD), for which the total reduction was of etot = 90%, with two variants of super-transus solution treatment (ST). The objective was to obtain a low Young’s modulus with sufficient high strength in purpose to use the alloy as a biomaterial for orthopedic implants. The microstructure analysis was conducted through X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HRTEM) investigations. The analyzed mechanical properties reveal promising values for yield strength (YS) and ultimate tensile strength (UTS) of about 770 and 1100 MPa, respectively, with a low value of Young’s modulus of about 48–49 GPa. The conclusion is that satisfactory mechanical properties for this type of alloy can be obtained if considering a proper combination of SPD + ST parameters and a suitable content of β-stabilizing alloying elements, especially the Zr/Nb ratio.

scholarly journals Phase Formation, Microstructure and Mechanical Properties of Mg67Ag33 as Potential Biomaterial

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 461
Author(s):  
Konrad Kosiba ◽  
Konda Gokuldoss Prashanth ◽  
Sergio Scudino
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Equilibrium Phase ◽  
Antibacterial Properties ◽  
Equilibrium Phase Diagram ◽  
Compressive Yield Strength ◽  
X Ray ◽  
Fine Grained ◽  
Equilibrium Phases

The phase and microstructure formation as well as mechanical properties of the rapidly solidified Mg67Ag33 (at. %) alloy were investigated. Owing to kinetic constraints effective during rapid cooling, the formation of equilibrium phases is suppressed. Instead, the microstructure is mainly composed of oversaturated hexagonal closest packed Mg-based dendrites surrounded by a mixture of phases, as probed by X-ray diffraction, electron microscopy and energy dispersive X-ray spectroscopy. A possible non-equilibrium phase diagram is suggested. Mainly because of the fine-grained dendritic and interdendritic microstructure, the material shows appreciable mechanical properties, such as a compressive yield strength and Young’s modulus of 245 ± 5 MPa and 63 ± 2 GPa, respectively. Due to this low Young’s modulus, the Mg67Ag33 alloy has potential for usage as biomaterial and challenges ahead, such as biomechanical compatibility, biodegradability and antibacterial properties are outlined.

scholarly journals Effect of Nanopores on Mechanical Properties of the Shape Memory Alloy

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 529
Author(s):  
Chunzhi Du ◽  
Zhifan Li ◽  
Bingfei Liu
Keyword(s):  
Mechanical Properties ◽  
Constitutive Model ◽  
Shape Memory ◽  
Young’S Modulus ◽  
Residual Strain ◽  
Surface Effect ◽  
Young's Modulus ◽  
Strain Curve ◽  
Stress Strain ◽  
Strength Limit

Nanoporous Shape Memory Alloys (SMA) are widely used in aerospace, military industry, medical and health and other fields. More and more attention has been paid to its mechanical properties. In particular, when the size of the pores is reduced to the nanometer level, the effect of the surface effect of the nanoporous material on the mechanical properties of the SMA will increase sharply, and the residual strain of the SMA material will change with the nanoporosity. In this work, the expression of Young’s modulus of nanopore SMA considering surface effects is first derived, which is a function of nanoporosity and nanopore size. Based on the obtained Young’s modulus, a constitutive model of nanoporous SMA considering residual strain is established. Then, the stress–strain curve of dense SMA based on the new constitutive model is drawn by numerical method. The results are in good agreement with the simulation results in the published literature. Finally, the stress-strain curves of SMA with different nanoporosities are drawn, and it is concluded that the Young’s modulus and strength limit decrease with the increase of nanoporosity.

Effect of Castor Oil Impregnation on the Physical and Mechanical Properties of Bacterial Cellulose

2012 ◽  
Vol 3 (1) ◽  
pp. 13-26
Author(s):  
Myrtha Karina ◽  
Lucia Indrarti ◽  
Rike Yudianti ◽  
Indriyati
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Young’S Modulus ◽  
Castor Oil ◽  
Young's Modulus ◽  
Physical And Mechanical Properties ◽  
Scanning Electron Micrographs ◽  
Elongation At Break ◽  
Acetone Water

The effect of castor oil on the physical and mechanical properties of bacterial cellulose is described. Bacterial cellulose (BC) was impregnated with 0.5–2% (w/v) castor oil (CO) in acetone–water, providing BCCO films. Scanning electron micrographs revealed that the castor oil penetrated the pores of the bacterial cellulose, resulting in a smoother morphology and enhanced hydrophilicity. Castor oil caused a slight change in crystallinity indices and resulted in reduced tensile strength and Young's modulus but increased elongation at break. A significant reduction in tensile strength and Young's modulus was achieved in BCCO films with 2% castor oil, and there was an improvement in elongation at break and hydrophilicity. Impregnation with castor oil, a biodegradable and safe plasticiser, resulted in less rigid and more ductile composites.

Mechanical Properties of Pyrolytic "SiOCN" Thin Coatings

1993 ◽  
Vol 308 ◽  
Author(s):  
Sandrine Bec ◽  
André Tonck ◽  
Jean-Luc Loubet
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Ceramic Coatings ◽  
Optical Observation ◽  
Thin Coatings ◽  
Polymer Precursors ◽  
Polymeric State

ABSTRACTPyrolysis of polymer precursors (polysilazane) is a technologically and economically interesting way to produce thin ceramic coatings. However, many cracks appear and decohesion occurs during pyrolysis when the ceramic coatings (SiOCN) are thicker than 0.5 micrometers. In order to understand these cracking phenomena, the coatings are mechanically characterized by nanoindentation at different stages of the pyrolysis heat treatment.During pyrolysis, the cracking temperature is detected by in-situ optical observation. The thickness of the coatings varies during pyrolysis from 3 micrometers at the polymeric state to 1 micrometer at the ceramic state. The coatings' properties, hardness and Young's modulus are evaluated after heat treatment, taking into account the substrate's influence. A large variation of these properties occurs at the cracking temperature. Both the hardness and the Young's modulus are multiplied by a factor of 10. By analysing these results, we show that cracking is correlated with the evolution of the coatings' mechanical properties during the transformation.

Sign in / Sign up

Export Citation Format

Share Document