scholarly journals Leachability and Stability of Hexavalent-Chromium-Contaminated Soil Stabilized by Ferrous Sulfate and Calcium Polysulfide

2018 ◽  
Vol 8 (9) ◽  
pp. 1431 ◽  
Author(s):  
Ting-Ting Zhang ◽  
Qiang Xue ◽  
Ming-Li Wei
Keyword(s):  
Hexavalent Chromium ◽  
Contaminated Soil ◽  
Ferrous Sulfate ◽  
X Ray Diffraction ◽  
Factors Affecting ◽  
X Ray ◽  
Acid Buffering ◽  
Before And After ◽  
Calcium Polysulfide ◽  
Better Than

Ferrous sulfate (FeSO4) and calcium polysulfide (CaS5) stabilization are practical approaches to stabilizing hexavalent chromium (Cr(VI))-contaminated soil. The leachability and stability of Cr(VI) and Cr are important factors affecting the effectiveness of stabilized Cr(VI)-contaminated soil. This study compared the leachability and stability of Cr(VI) and Cr in Cr(VI)-contaminated soil stabilized by using FeSO4 and CaS5. The contaminated soil was characterized before and after stabilization, and the effectiveness of FeSO4 and CaS5 stabilization was assessed using leaching, bioaccessibility, alkaline digestion, sequential extraction, and X-ray diffraction tests. Results showed that FeSO4 and CaS5 significantly reduced the leachability and Cr(VI) content in the contaminated soil. The acid-buffering capacity and stability (leachability, bioaccessibility, speciation distribution, and mineral composition) of the Cr(VI)/Cr and Cr(VI) content of CaS5 were better than those of FeSO4. This study demonstrated that CaS5 had a better effect than FeSO4 on the stabilization of Cr(VI) in Cr(VI)-contaminated soil. The CaS5 significantly enhanced the stabilization and immobilization of Cr(VI) and reduced its leachability and toxicity.

Evaluation of Freezing Methods by Low Temperature X-Ray Diffraction

1977 ◽  
Vol 35 ◽  
pp. 330-333
Author(s):  
T. Gulik-Krzywicki ◽  
M.J. Costello
Keyword(s):  
Biological Materials ◽  
Molecular Organization ◽  
X Ray Diffraction ◽  
Glass Capillary ◽  
X Ray ◽  
Rate Dependent ◽  
Before And After ◽  
Freeze Etching ◽  
Diffraction Patterns ◽  
Set Up

Freeze-etching electron microscopy is currently one of the best methods for studying molecular organization of biological materials. Its application, however, is still limited by our imprecise knowledge about the perturbations of the original organization which may occur during quenching and fracturing of the samples and during the replication of fractured surfaces. Although it is well known that the preservation of the molecular organization of biological materials is critically dependent on the rate of freezing of the samples, little information is presently available concerning the nature and the extent of freezing-rate dependent perturbations of the original organizations. In order to obtain this information, we have developed a method based on the comparison of x-ray diffraction patterns of samples before and after freezing, prior to fracturing and replication.Our experimental set-up is shown in Fig. 1. The sample to be quenched is placed on its holder which is then mounted on a small metal holder (O) fixed on a glass capillary (p), whose position is controlled by a micromanipulator.

A New Polyethylene Corrosion Protecting Coating with Ion Selectivity

2011 ◽  
Vol 314-316 ◽  
pp. 273-278
Author(s):  
Yu Hua Dong ◽  
Ke Ren ◽  
Qiong Zhou
Keyword(s):  
Ion Selectivity ◽  
Nano Particles ◽  
Ammonium Bromide ◽  
Linear Low Density Polyethylene ◽  
X Ray Diffraction ◽  
Sulfosalicylic Acid ◽  
X Ray ◽  
Chemically Modified ◽  
Before And After ◽  
Industrial Standards

Linear low density polyethylene (LLDPE) was chemically modified with grafting maleic anhydride (MAH) monomer on its backbone by melting blending. Nano-particles SiO2 was modified by cationic surfactant hexadecyl trimethyl ammonium bromide (CTAB) and anionic surfactant sulfosalicylic acid (SSA) and added to PE coating respectively. Measurement of membrane potential showed that the coating containing modified SiO2 nano-particles had characteristic of ion selectivity. The properties of the different coatings were investigated according to relative industrial standards. Experimental results indicated that PE coating with ion selectivity had better performances, such as adhesion strength, cathodic disbonding and anti-corrosion, than those of coating without ion selectivity. Crystal structure of the coatings before and after alkali corrosion was characterized by Fourier transform infrared spectra (FTIR) and X-ray diffraction (XRD). Structure of the coating without ion selectivity was damaged by NaOH alkali solution, causing mechanical properties being decreased. And the structure of the ion selective coatings was not affected.

scholarly journals Application of nanoscale zero-valent iron in hexavalent chromium-contaminated soil: A review

2020 ◽  
Vol 9 (1) ◽  
pp. 736-750
Author(s):  
Xilu Chen ◽  
Xiaomin Li ◽  
Dandan Xu ◽  
Weichun Yang ◽  
Shaoyuan Bai
Keyword(s):  
Heavy Metal ◽  
Hexavalent Chromium ◽  
Contaminated Soil ◽  
Zero Valent Iron ◽  
Toxic Heavy Metal ◽  
Factors Affecting ◽  
Metal Pollutants ◽  
Nanoscale Zero Valent Iron ◽  
Low Toxicity ◽  
Heavy Metal Pollutants

AbstractChromium (Cr) is a common toxic heavy metal that is widely used in all kinds of industries, causing a series of environmental problems. Nanoscale zero- valent iron (nZVI) is considered to be an ideal remediation material for contaminated soil, especially for heavy metal pollutants. As a material of low toxicity and good activity, nZVI has been widely applied in the in situ remediation of soil hexavalent chromium (Cr(vi)) with mobility and toxicity in recent years. In this paper, some current technologies for the preparation of nZVI are summarized and the remediation mechanism of Cr(vi)-contaminated soil is proposed. Five classified modified nZVI materials are introduced and their remediation processes in Cr(vi)-contaminated soil are summarized. Key factors affecting the remediation of Cr(vi)-contaminated soil by nZVI are studied. Interaction mechanisms between nZVI-based materials and Cr(vi) are explored. This study provides a comprehensive review of the nZVI materials for the remediation of Cr(vi)-contaminated soil, which is conducive to reducing soil pollution.

Sedimentary Clays as Geopolymer Precursor

2018 ◽  
Vol 39 ◽  
pp. 97-111
Author(s):  
F. Mostefa ◽  
Nasr Eddine Bouhamou ◽  
H.A. Mesbah ◽  
Salima Aggoun ◽  
D. Mekhatria
Keyword(s):  
Sodium Hydroxide ◽  
Mineralogical Composition ◽  
Cementitious Materials ◽  
Raw Material ◽  
X Ray Diffraction ◽  
Calcination Time ◽  
Calorimetric Analysis ◽  
X Ray ◽  
Before And After ◽  
Mechanical Performances

This work aims to study the feasibility of making a geopolymer cement based on dredged sediments, from the Fergoug dam (Algeria) and to evaluate their construction potential particularly interesting in the field of special cementitious materials. These sediments due to their mineralogical composition as aluminosilicates; are materials that can be used after heat treatment. Sedimentary clays were characterized before and after calcination by X-ray diffraction, ATG / ATD, spectroscopy (FTIR) and XRF analysis. The calcination was carried out on the raw material sieved at 80 μm for a temperature of 750 ° C, for 3.4 and 5 hours. The reactivity of the calcined products was measured using isothermal calorimetric analysis (DSC) on pastes prepared by mixing an alkaline solution of sodium hydroxide (NaOH) 8 M in an amount allowing to have a Na / Al ratio close to 1 (1: 1). Also, cubic mortar samples were prepared with a ratio L / S: 0.8, sealed and cured for 24 hours at 60 ° C and then at room temperature until the day they were submited to mechanical testing. to check the extent of geopolymerization. The results obtained allowed to optimize the calcination time of 5 hours for a better reactivity of these sediments, and a concentration of 8M of sodium hydroxide and more suitable to have the best mechanical performances.

Influence of High Current Pulsed Electron Beam Irradiation on Ni-P Electroless Plating

2011 ◽  
Vol 299-300 ◽  
pp. 77-81
Author(s):  
Yang Xu ◽  
Sheng Zhi Hao ◽  
Xiang Dong Zhang ◽  
Min Cai Li ◽  
Chuang Dong
Keyword(s):  
Electroless Plating ◽  
Electron Beam Irradiation ◽  
Xrd Analysis ◽  
High Current ◽  
X Ray Diffraction ◽  
X Ray ◽  
Pulsed Electron Beam ◽  
6063 Aluminum Alloy ◽  
Pre Treatment ◽  
Better Than

The surface irradiation of 6063 aluminum alloy by high current pulsed electron was conducted with the aim of replacing the complicated pre-treatment in the processes of electroless plating. To explore the microstructure changes, optical metallography, SEM (scanning electron microscope), XRD (X-ray diffraction) analyses were carried out, and the sliding tests were used for the detection of wear resistance. It was concluded that the HCPEB irradiation could replace the pre-treatment of aluminum substrate as required in conventional electroless plating with a decreased surface roughness of Ni-P alloy plating layer. The plates exhibited an amorphous microstructure as demonstrated by XRD analysis. The plates, produced with the routine of HCPEB irradiation, activation and electroless plating possess, also exhibited good quality, even better than that of conventional electroless plating technique.

scholarly journals Purification, crystallization and preliminary X-ray diffraction analysis of a hydroxycinnamoyl-CoA shikimate/quinate hydroxycinnamoyltransferase (HCT) fromCoffea canephorainvolved in chlorogenic acid biosynthesis

2012 ◽  
Vol 68 (7) ◽  
pp. 824-828 ◽  
Author(s):  
Laura A. Lallemand ◽  
James G. McCarthy ◽  
Sean McSweeney ◽  
Andrew A. McCarthy
Keyword(s):  
Structural Data ◽  
Coffea Canephora ◽  
Molecular Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cell Parameters ◽  
Key Enzyme ◽  
Substrate Specifities ◽  
Drop Technique ◽  
Better Than

Chlorogenic acids (CGAs) are a group of soluble phenolic compounds that are produced by a variety of plants, includingCoffea canephora(robusta coffee). The last step in CGA biosynthesis is generally catalysed by a specific hydroxycinnamoyl-CoA quinate hydroxycinnamoyltransferase (HQT), but it can also be catalysed by the more widely distributed hydroxycinnamoyl-CoA shikimate/quinate hydroxycinnamoyltransferase (HCT). Here, the cloning and overexpression of HCT fromC. canephorainEscherichia colias well as its purification and crystallization are presented. Crystals were obtained by the sitting-drop technique at 293 K and X-ray diffraction data were collected on the microfocus beamline ID23-2 at the ESRF. The HCT crystals diffracted to better than 3.0 Å resolution, belonged to space groupP42212 with unit-cell parametersa=b= 116.1,c= 158.9 Å and contained two molecules in the asymmetric unit. The structure was solved by molecular replacement and is currently under refinement. Such structural data are needed to decipher the molecular basis of the substrate specifities of this key enzyme, which belongs to the large plant acyl-CoA-dependent BAHD acyltransferase superfamily.

Aging of iron manganite negative temperature coefficient thermistors

1998 ◽  
Vol 13 (5) ◽  
pp. 1238-1242 ◽  
Author(s):  
T. Battault ◽  
R. Legros ◽  
A. Rousset
Keyword(s):  
Temperature Coefficient ◽  
Spinel Structure ◽  
Negative Temperature Coefficient ◽  
Negative Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Octahedral Sites ◽  
Before And After ◽  
Structural Equilibrium ◽  
Electrical Data

“Aging,” defined as the drift of resistance with temperature after 1000 h, was investigated for iron manganite temperature coefficient thermistors. For these devices, aging is relatively large, about 10%. The cationic distributions before and after aging were determined by Mössbauer spectroscopy. These distributions explain all the x-ray diffraction and correlated electrical data. The origin of the aging observed on iron manganites thermistors has been identified. It is due to the migration of Fe3+ ions from tetrahedral to octahedral sites of the spinel structure in order to reach a structural equilibrium.

Oxidation of Alloy-X in Subcritical, Transition, and Supercritical Water

CORROSION ◽  
10.5006/3881 ◽  
2021 ◽  
Author(s):  
Zachary Karmiol ◽  
Dev Chidambaram
Keyword(s):  
Supercritical Water ◽  
Photoelectron Spectroscopy ◽  
Focused Ion Beam ◽  
Elevated Temperatures ◽  
Subcritical Water ◽  
Ion Beam ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nickel Based Superalloy ◽  
Before And After

This work investigates the oxidation of a nickel based superalloy, namely Alloy X, in water at elevated temperatures: subcritical water at 261°C and 27 MPa, the transition between subcritical and supercritical water at 374°C and 27 MPa, and supercritical water at 380°C and 27 MPa for 100 hours. The morphology of the sample surfaces were studied using scanning electron microscopy coupled with focused ion beam milling, and the surface chemistry was investigated using X-ray diffraction, Raman spectroscopy, energy dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy before and after exposure studies. Surfaces of all samples were identified to comprise of a ferrite spinel containing aluminum.

scholarly journals MSMEG_6292, a Mycobacterium smegmatis RNA polymerase secondary channel-binding protein: purification, crystallization and X-ray diffraction analysis

2018 ◽  
Vol 74 (9) ◽  
pp. 543-548
Author(s):  
Abyson Joseph ◽  
Valakunja Nagaraja ◽  
Ramanathan Natesh
Keyword(s):  
Rna Polymerase ◽  
Mycobacterium Smegmatis ◽  
Transcriptional Activity ◽  
Molecular Replacement ◽  
X Ray Diffraction ◽  
Secondary Channel ◽  
X Ray ◽  
Cell Parameters ◽  
Crystallization Method ◽  
Better Than

The transcriptional activity of RNA polymerase (RNAP) is controlled by a diverse set of regulatory factors. A subset of these regulators modulate the activity of RNAP through its secondary channel. Gre factors reactivate stalled elongation complexes by enhancing the intrinsic cleavage activity of RNAP. In the present study, the protein MSMEG_6292, a Gre-factor homologue from Mycobacterium smegmatis, was expressed heterologously in Escherichia coli and purified using standard chromatographic techniques. The hanging-drop vapour-diffusion crystallization method yielded diffraction-quality crystals. The crystals belonged to the trigonal space group P3121 (or its enantiomorph P3221), with unit-cell parameters a = b = 83.15, c = 107.07 Å, α = β = 90, γ = 120°. The crystals diffracted to better than 3.0 Å resolution. Molecular-replacement attempts did not yield any phasing models; hence, platinum derivatization was carried out with K2PtCl4 and derivative data were collected to 3.4 Å resolution.

Sign in / Sign up

Export Citation Format

Share Document