scholarly journals The Effect of Sand Type on the Rheological Properties of Self-Compacting Mortar

Buildings ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 441
Author(s):  
Song Yang ◽  
Jingbin Zhang ◽  
Xuehui An ◽  
Bing Qi ◽  
Wenqiang Li ◽  
...  
Keyword(s):  
Specific Gravity ◽  
Water Absorption ◽  
Rheological Properties ◽  
Linear Correlation ◽  
Particle Shape ◽  
River Sand ◽  
Manufactured Sand ◽  
Slump Flow ◽  
Influence Of Water ◽  
Sand Type

In order to understand the effect of sand type on the rheological properties of self-compacting mortar, four varieties of sand, namely, quartz sand (QS), river sand (RS), and two kinds of manufactured sand, marked as MS-A and MS-B, were studied. As part of this study, the sands’ particle shape parameters, such as their length:width ratio and roundness, were determined. Mortars containing the four varieties of sand were tested using the slump flow test and the V-funnel test in oven-dried (OD) and saturated surface-dried (SSD) conditions in order to identify the water absorption, shape-related differences, and specific gravity in their rheological performance. The changing trends of the slump flows and the V-funnel times of the different mortars in OD and SSD were similar. By eliminating the influence of water absorption on mortar rheology, shape–weight parameters, such as the ratio between the length:width ratio and specific gravity (LWS) and the product of roundness and specific gravity (ROS), were defined in order to quantify the compound effects of sand type on mortar rheology. The regression analysis showed an excellent linear correlation between slump flow and both LWS and ROS, and a very good linear correlation was also demonstrated between the V-funnel time and both LWS and ROS. Based on the particle shape–weight parameters, the rheological properties of mortars can be predicted. Based on the mortar rheological threshold theory, the self-compacting mortar (SCM) zone can be drawn. The predicted SCM zone overlaps considerably with the experimental SCM zone for MS-A.

Influence of Water Absorption on The Selected Properties of Hemp Hurds Composites

2015 ◽  
Vol 10 (1) ◽  
pp. 123-132
Author(s):  
Lucia Kidalova ◽  
Nadezda Stevulova ◽  
Eva Terpakova
Keyword(s):  
Water Absorption ◽  
Influence Of Water

Properties of Artificial Lightweight Aggregates (ALAs) Made of Dredged Soil Mixed with Waste Catalyst Slag

2012 ◽  
Vol 174-177 ◽  
pp. 1079-1085 ◽  
Author(s):  
Si Nae Jo ◽  
Yoo Tack Kim ◽  
Seung Gu Kang ◽  
Chang Sam Kim
Keyword(s):  
Specific Gravity ◽  
Water Absorption ◽  
Lightweight Concrete ◽  
Sintering Temperature ◽  
Thermal Power ◽  
Lightweight Aggregates ◽  
Dredged Soil ◽  
Porous Carriers ◽  
Black Core ◽  
Sintering Method

The artificial lightweight aggregates (ALAs) were manufactured using dredged soil produced at thermal power plant and waste catalyst slag by direct sintering method at 1050~1250°C for 10min. The ALAs of 100% dredged soil showed the black core phenomenon even at the low sintering temperature as 1050°C and become lightened by bloating pores in black core area with sintering temperature. On the other hand, the aggregates with 100% waste catalyst slag did not showed black coring and bloating phenomenon and had the low forming ability and many cracks inside. Adding the dredged soil to the waste catalyst slag decrease the specific gravity by promoting the black coring and bloating inside. The water absorption(%) of ALAs decreased with sintering temperature. The ALAs fabricated in this study showed the specific gravity of 0.8~2.0 and water absorption of 2~16% so it could be applied to various fields such as the lightweight concrete or the field of the porous carriers for purification of a contaminated soil or water.

The Reasonable Amount of Polypropylene Fiber on Low-Intensity Manufactured Sand Concrete in the Case of Fixed Powder Paste

2014 ◽  
Vol 1065-1069 ◽  
pp. 2005-2010
Author(s):  
Hao Lu ◽  
Gu Hua Li ◽  
Jia Wei Yang ◽  
Liang Zhang ◽  
Ze Jiang Sun ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Polypropylene Fiber ◽  
Particle Type ◽  
River Sand ◽  
Manufactured Sand ◽  
Low Intensity ◽  
Reasonable Amount

Compared with the river sand, manufactured sand’s particle type and gradation is relatively poor and the surface is mat .The manufactured sand also has a big effect on the workability of concrete. In this paper,the Equivalent powder paste’s volume of manufactured sand concrete was determined according to Mehta and Aitcin’s ideas for the preparation of HPC,at the same time,the equivalent powder paste volume is assumed as the cement paste volume in the experiment. The influence of polypropylene fiber on Manufactured sand concrete’s workability and Compressive strength were researched in the case of fixed powder paste .

scholarly journals Mechanical Properties of High Calcium Flyash- GGBFS Geopolymer Paste, Mortar and the Effect of Glass Fibre Mesh on the Strength of Geopolymer Mortar Tile

2020 ◽  
Vol 9 (6) ◽  
pp. 722-729
Keyword(s):  
Glass Fibre ◽  
Demolition Waste ◽  
River Sand ◽  
Manufactured Sand ◽  
Granulated Blast Furnace Slag ◽  
Fine Aggregates ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Fibre Mesh ◽  
Geopolymer Paste

In this paper, a combination of high-calcium fly ash (HCFA) and ground granulated blast furnace slag (GGBFS) was used along with a combination of sodium hydroxide (NaOH) and sodium silicate(Na2SiO3 ) as alkaline activators (AAs) to produce geopolymer paste and mortar. The alkaline activator ratio (AAR) was maintained at 1.5 apart from their molarity at 10 for the study. A rational method, namely minimum voids approach was used for the mix design. A commercially available glass fibre mesh was used as reinforcement in the geopolymer mortar produced above, to assess its potential for use as a flooring tile. The influence of W/S (water-to-solids) ratio and the influence of various fine aggregates, namely, river sand (R), manufactured sand (M) and construction demolition waste (D) on the various geopolymer system (GP) and on the strength characteristics, are highlighted. A maximum transverse strength (TS) of 6.25 N/mm2 could be attained by the geopolymer tile, using three layers of glass fibre mesh and GP mortar developed. The study indicates that a combination of FA and GGBFS helps us to attain substantial strength under ambient temperature in geopolymer mortar

scholarly journals Evaluations of All-in-One, Polycarboxylate-Based Superplasticizer with Viscosity Modifying Agents for the Application of Normal-Strength, High-Fluidity Concrete

2021 ◽  
Vol 11 (23) ◽  
pp. 11141
Author(s):  
Tae-Woong Kong ◽  
Hyun-Min Yang ◽  
Han-Seung Lee ◽  
Chang-Bok Yoon
Keyword(s):  
Compressive Strength ◽  
Rheological Properties ◽  
Yield Stress ◽  
Lower Yield ◽  
Lower Yield Stress ◽  
Slump Flow ◽  
Different Types ◽  
Long Time ◽  
Normal Strength ◽  
Physical Phenomena

High fluidity concrete exhibits an excellent self-compacting property. However, the application of typical high-fluidity concrete is limited in the normal strength range (18~35 MPa) due to the large amount of binder. Therefore, it is important to solve these problems by adding a viscosity modifying agent (VMA) with a superplasticizer (PCE), which helps to improve the fluidity of the concrete. In addition, the rheology and stability of the concrete with VMA can be improved by preventing bleeding and segregation issues. Current studies focused on the physical phenomena of concrete such as the fluidity, rheological properties, and compressive strength of normal-strength, high-fluidity concrete (NSHFC) with different types of a polycarboxylate-based superplasticizer (NPCE). The obtained results suggested that the combinations of all-in-one polycarboxylate-based superplasticizers (NPCE) did not cause any cohesion or sedimentation even stored for a long time. The combination of three types of VMA showed the best fluidity (initial slump flow of 595~630 mm) without any segregation and bleeding, and the compressive strength at 28 days was also found to be the highest: 34–37 MPa. From these results, the combination of PCE (2.0%) + HPMC (0.3%) + WG (0.1%) + ST (0.1%) showed an 18% higher plastic viscosity and -4.4% lower yield stress than Plain.

scholarly journals Mechanical and Durability Properties of Fibre Reinforced Concrete made with OPC, GGBS and Metakaolin

2019 ◽  
Vol 8 (10) ◽  
pp. 3286-3290
Keyword(s):  
Reinforced Concrete ◽  
Fiber Reinforced Concrete ◽  
Industrial Wastes ◽  
Test Results ◽  
River Sand ◽  
Manufactured Sand ◽  
Durability Properties ◽  
Strength Tests ◽  
Massive Scale ◽  
Strength And Durability

Concrete is a globally utilized material in the construction field. In the last few decades, Concrete consumption has become multifold and usage has enhanced in massive scale due to the rapid growth of infra sector. Generally, Concrete consists of cement, aggregate, and water; these ingredients become more expensive day by day and additionally hard to please and is increasing widely. During the process of making Ordinary Portland Cement(OPC) produces a large amount of greenhouse gases and the environment being polluted. To minimize the cement utilization and environmental issues is essential to switch the cement by another alternate materials such as pozzolanas. The various number of pozzolanic materials comes from industrial wastes are Groundz Granulatedz Blastz furnacez Slagz (GGBS), xFlyqAsh (FA), zSilicazFume (SF), Metakaolin (MK) etc are utilized in concrete. Similarly, the availability of river sand is getting drained furthermore it turns out troublesome. In order to avoid this problem river sand is alter by zManufacturedkSand (M Sand). An attempt is made in the present investigation to study on properties of fiber reinforced concrete (qsteelu fibers @ 1% of binder) of M40 grade made with OPC, GGBS, MK and manufactured sand. In this study, OPC is replaced by GGBS and MK in different proportions. By casting requisite number of cubes, cylinders then zMechanical properties are determined such as fCompressivekstrength,sSplitdtensile strength tests and durability properties are determined by conducting Water absorption and Sorptivity tests. Test results are compared between controlled concrete and innovative concrete of M40 grade.It is observed that 30%(15%GGBS,15%MK) replacement is optimum for strength and durability criteria.

scholarly journals PROPERTIES OF MORTARS CONTAINING TIRE RUBBER WASTE AND EXPANDED POLYSTYRENE (EPS)

2018 ◽  
pp. 219-225 ◽  
Author(s):  
Adriane Pczieczek ◽  
Adilson Schackow ◽  
Carmeane Effting ◽  
Itamar Ribeiro Gomes ◽  
Talita Flores Dias
Keyword(s):  
Compressive Strength ◽  
Specific Gravity ◽  
Water Absorption ◽  
Expanded Polystyrene ◽  
Fine Aggregate ◽  
Tire Rubber ◽  
Air Content ◽  
Rubber Waste ◽  
Hardened State ◽  
Entrained Air

This study aims to evaluate the application of discarded tire rubber waste and Expanded Polystyrene (EPS) in mortar. For mortars fine aggregate was replaced by 10%, 20% and 30% of rubber and, 7.5% and 15% of EPS. We have verified the consistency, density, amount of air and water retentitivity in fresh state. The compressive strength, water absorption, voids ratio and specific gravity have been also tested in hardened state. The application of rubber powder contributed to the increase in entrained air content and in reducing specific gravity, as well as reducing compressive strength at 28 days. The addition of EPS also contributed to the increase of workability, water absorption and voids ratio, and decreased density and compressive strength when compared to the reference mortar. The use of rubber waste and EPS in mortar made the material more lightweight and workable. The mortars mixtures containing 10% rubber and 7.5% EPS showed better results.

Fresh, Durability and Mechanical Behavior of Self Consolidating Concrete Incorporating Fly Ash and Admixture under Hot Weather

2021 ◽  
Vol 904 ◽  
pp. 453-457
Author(s):  
Samer Al Martini ◽  
Reem Sabouni ◽  
Abdel Rahman Magdy El-Sheikh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Weather Conditions ◽  
Chloride Penetration ◽  
The Self ◽  
Fresh Properties ◽  
Self Consolidating Concrete ◽  
Slump Flow ◽  
Hot Weather

The self-consolidating concrete (SCC) become the material of choice by concrete industry due to its superior properties. However, these properties need to be verified under hot weather conditions. The paper investigates the behavior of SCC under hot weather. Six SCC mixtures were prepared under high temperatures. The SCC mixtures incorporated polycarboxylate admixture at different dosages and prolonged mixed for up to 2 hours at 30 °C and 40 °C. The cement paste was replaced with 20% of fly ash (FA). The fresh properties were investigated using slump flow, T50, and VSI tests. The compressive strength was measured at 3, 7, and 28 days. The durability of SCC mixtures was evaluated by conducting rapid chloride penetration and water absorption tests.

Sign in / Sign up

Export Citation Format

Share Document