scholarly journals Analysis of a Wide Range of Commercial Exterior Wood Coatings

Coatings ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1013
Author(s):  
Michael J. Gibbons ◽  
Saeid Nikafshar ◽  
Tina Saravi ◽  
Katie Ohno ◽  
Sanjeev Chandra ◽  
...  
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Water Uptake ◽  
Water Immersion ◽  
Contact Angles ◽  
Solid Content ◽  
Image Processing Technique ◽  
Wide Range ◽  
Water Based ◽  
Exterior Wood

This study was focused on measuring the properties of twenty-three commercially available coatings formulated for exterior wood applications. The coatings were characterized by measuring their surface tension, solid content, viscosity, pH, and glass transition temperatures (Tg). Additionally, the wetting properties of coating droplets on wood substrates were measured. The contact angle of solvent-based and water-based coatings were characterized on untreated southern yellow pine wood samples using high-resolution image analysis and the Young–Laplace solution. An innovative image processing technique for determining the average diameter of coating droplets on wood was developed, and an iterative method to calculate the average contact angle using the Young–Laplace solution was applied. The water-resistance of the coated wood samples was evaluated during one week of water immersion tests. In general, solvent-based coatings had significantly lower contact angles and water uptake than water-based coatings. Water-based paint samples had the largest average contact angle (81°), and solvent-based transparent penetrating stains had the smallest contact angle (13.9°). A strong correlation was observed between the coating water uptake and their surface tension and solid content.

scholarly journals Amphiphobic Nanostructured Coatings for Industrial Applications

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 787 ◽  
Author(s):  
Federico Veronesi ◽  
Giulio Boveri ◽  
Mariarosa Raimondo
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Photoelectron Spectroscopy ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Friction Reduction ◽  
Hybrid Coatings ◽  
Wetting Behavior ◽  
Wide Range ◽  
Solid Liquid

The search for surfaces with non-wetting behavior towards water and low-surface tension liquids affects a wide range of industries. Surface wetting is regulated by morphological and chemical features interacting with liquid phases under different ambient conditions. Most of the approaches to the fabrication of liquid-repellent surfaces are inspired by living organisms and require the fabrication of hierarchically organized structures, coupled with low surface energy chemical composition. This paper deals with the design of amphiphobic metals (AM) and alloys by deposition of nano-oxides suspensions in alcoholic or aqueous media, coupled with perfluorinated compounds and optional infused lubricant liquids resulting in, respectively, solid–liquid–air and solid–liquid–liquid working interfaces. Nanostructured organic/inorganic hybrid coatings with contact angles against water above 170°, contact angle with n-hexadecane (surface tension γ = 27 mN/m at 20 °C) in the 140–150° range and contact angle hysteresis lower than 5° have been produced. A full characterization of surface chemistry has been undertaken by X-ray photoelectron spectroscopy (XPS) analyses, while field-emission scanning electron microscope (FE-SEM) observations allowed the estimation of coatings thicknesses (300–400 nm) and their morphological features. The durability of fabricated amphiphobic surfaces was also assessed with a wide range of tests that showed their remarkable resistance to chemically aggressive environments, mechanical stresses and ultraviolet (UV) radiation. Moreover, this work analyzes the behavior of amphiphobic surfaces in terms of anti-soiling, snow-repellent and friction-reduction properties—all originated from their non-wetting behavior. The achieved results make AM materials viable solutions to be applied in different sectors answering several and pressing technical needs.

scholarly journals Influence of moisture content on the contact angle and surface tension measured on birch wood surfaces

2021 ◽  
Author(s):  
Rami Benkreif ◽  
Fatima Zohra Brahmia ◽  
Csilla Csiha
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Moisture Content ◽  
Solid Wood ◽  
Contact Angles ◽  
Surface Moisture ◽  
Wood Coatings ◽  
The Relationship ◽  
Wood Surfaces

AbstractSurface tension of solid wood surfaces affects the wettability and thus the adhesion of various adhesives and wood coatings. By measuring the contact angle of the wood, the surface tension can be calculated based on the Young-Dupré equation. Several publications have reported on contact angle measured with different test liquids, under different conditions. Results can only be compared if the test conditions are similar. While the roles of the drop volume, image shooting time etc., are widely recognized, the role of the wood surface moisture content (MC) is not evaluated in detail. In this study, the effect of wood moisture content on contact angle values, measured with distilled water and diiodomethane, on sanded birch (Betula pendula) surfaces was investigated, in order to find the relationship between them. With increasing MC from approximately 6% to 30%, increasing contact angle (decreasing surface tension) values were measured according to a logarithmic function. The function makes possible the calculation of contact angles that correspond to different MCs.

scholarly journals Is contact angle a cause or an effect? – A cautionary tale

2020 ◽  
Vol 146 ◽  
pp. 03004
Author(s):  
Douglas Ruth
Keyword(s):  
Contact Angle ◽  
Solid Surface ◽  
Contact Angles ◽  
Two Dimensions ◽  
Experimental Results ◽  
Flow In Porous Media ◽  
Two Dimensional ◽  
Wide Range ◽  
Fluid Drop ◽  
Surrounding Fluid

The most influential parameter on the behavior of two-component flow in porous media is “wettability”. When wettability is being characterized, the most frequently used parameter is the “contact angle”. When a fluid-drop is placed on a solid surface, in the presence of a second, surrounding fluid, the fluid-fluid surface contacts the solid-surface at an angle that is typically measured through the fluid-drop. If this angle is less than 90°, the fluid in the drop is said to “wet” the surface. If this angle is greater than 90°, the surrounding fluid is said to “wet” the surface. This definition is universally accepted and appears to be scientifically justifiable, at least for a static situation where the solid surface is horizontal. Recently, this concept has been extended to characterize wettability in non-static situations using high-resolution, two-dimensional digital images of multi-component systems. Using simple thought experiments and published experimental results, many of them decades old, it will be demonstrated that contact angles are not primary parameters – their values depend on many other parameters. Using these arguments, it will be demonstrated that contact angles are not the cause of wettability behavior but the effect of wettability behavior and other parameters. The result of this is that the contact angle cannot be used as a primary indicator of wettability except in very restricted situations. Furthermore, it will be demonstrated that even for the simple case of a capillary interface in a vertical tube, attempting to use simply a two-dimensional image to determine the contact angle can result in a wide range of measured values. This observation is consistent with some published experimental results. It follows that contact angles measured in two-dimensions cannot be trusted to provide accurate values and these values should not be used to characterize the wettability of the system.

scholarly journals Experimental Investigation of Coal Dust Wettability Based on Surface Contact Angle

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Gang Zhou ◽  
Han Qiu ◽  
Qi Zhang ◽  
Mao Xu ◽  
Jiayuan Wang ◽  
...  
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Specific Surface ◽  
Coal Dust ◽  
Single Point ◽  
Contact Angles ◽  
Critical Surface ◽  
Volume Percentage ◽  
Surface Areas ◽  
Specific Surface Areas

Wettability is one of the key chemical properties of coal dust, which is very important to dedusting. In this paper, the theory of liquid wetting solid was presented firstly; then, taking the gas coal of Xinglongzhuang coal mine in China as an example, by determination of critical surface tension of coal piece, it can be concluded that only when the surface tension of surfactant solution is less than 45 mN/m can the coal sample be fully wetted. Due to the effect of particle dispersity, compared with the contact angle of milled coal particle, not all the contact angles of screened coal powder with different sizes have a tendency to increase. Furthermore, by the experiments of coal samples’ specific surface areas and porosities, it can be achieved that the volume of single-point total pore decreases with the gradual decreasing of coal’s porosity, while the ultramicropores’ dispersities and multipoint BET specific surface areas increase. Besides, by a series of contact angle experiments with different surfactants, it can be found that with the increasing of porosity and the decreasing of volume percentage of ultramicropore, the contact angle tends to reduce gradually and the coal dust is much easier to get wetted.

scholarly journals A spherical particle straddling a fluid/gas interface in an axisymmetric straining flow

1990 ◽  
Vol 217 ◽  
pp. 263-298 ◽  
Author(s):  
J. A. Stoos ◽  
L. G. Leal
Keyword(s):  
Contact Angle ◽  
Spherical Particle ◽  
Numerical Solutions ◽  
Contact Angles ◽  
Boundary Integral ◽  
Equilibrium Contact Angle ◽  
Equilibrium Configurations ◽  
Wide Range ◽  
The Stability ◽  
Neutrally Buoyant

Numerical solutions, obtained via the boundary-integral technique, are used to consider the effect of a linear axisymmetric straining flow on the existence of steady-state configurations in which a neutrally buoyant spherical particle straddles a gas–liquid interface. The problem is directly applicable to predictions of the stability of particle capture in flotation processes, and is also of interest in the context of contact angle and surface tension measurements. A primary goal of the present study is a determination of the critical capillary number, Cac, beyond which an initially captured particle is pulled from the interface by the flow, and the dependence of Cac on the equilibrium contact angle θc. We also present equilibrium configurations for a wide range of contact angles and subcritical capillary numbers.

Investigation of Pool Boiling Critical Heat Flux Enhancement on a Modified Surface Through the Dynamic Wetting of Water Droplets

2012 ◽  
Vol 134 (7) ◽  
Author(s):  
Ho Seon Ahn ◽  
Joonwon Kim ◽  
Moo Hwan Kim
Keyword(s):  
Surface Tension ◽  
Heat Flux ◽  
Contact Angle ◽  
Critical Heat Flux ◽  
Pool Boiling ◽  
Water Layer ◽  
Contact Angles ◽  
Water Droplets ◽  
Dynamic Wetting ◽  
Modified Surface

Dynamic wetting behaviors of water droplet on the modified surface were investigated experimentally. Dynamic contact angles were measured as a characterization method to explain the extraordinary pool boiling critical heat flux (CHF) enhancement on the zirconium surface by anodic oxidation modification. The sample surface is rectangular zirconium alloy plates (20 × 25 × 0.7 mm), and 12 μl of deionized water droplets were fallen from 40 mm of height over the surface. Dynamic wetting movement of water on the surface showed different characteristics depending on static contact angle (49.3 deg–0 deg) and surface temperature (120 °C–280 °C). Compared with bare surface, wettable and spreading surface had no-receding contact angle jump and seemed stable evaporating meniscus of liquid droplet in dynamic wetting condition on hot surface. This phenomenon could be explained by the interaction between the evaporation recoil and the surface tension forces. The surface tension force increased by micro/nanostructure of the modified zirconium surface suppresses the vapor recoil force by evaporation which makes the water layer unstable on the heated surface. Thus, such increased surface force could sustain the water layer stable in pool boiling CHF condition so that the extraordinary CHF enhancement could be possible.

scholarly journals Surface, Volumetric, and Wetting Properties of Oleic, Linoleic, and Linolenic Acids with Regards to Application of Canola Oil in Diesel Engines

2019 ◽  
Vol 9 (17) ◽  
pp. 3445 ◽  
Author(s):  
Anna Zdziennicka ◽  
Katarzyna Szymczyk ◽  
Bronisław Jańczuk ◽  
Rafał Longwic ◽  
Przemysław Sander
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Diesel Engines ◽  
Canola Oil ◽  
Contact Angles ◽  
Physiochemical Properties ◽  
Engine Valve ◽  
Wetting Properties ◽  
Main Components ◽  
Adhesion Work

Oleic, linoleic, and linolenic acids are the main components of canola oil and their physiochemical properties decide on the use of canola oil as fuel for diesel engines. Therefore, the measurements of the surface tension of oleic, linoleic, and linolenic acids being the components of the canola oil, as well as their contact angles on the polytetrafluoroethylene (PTFE), poly(methyl methacrylate) (PMMA), and engine valve, were made. Additionally, the surface tension and contact angle on PTFE, PMMA, and the engine valve of the oleic acid and n-hexane mixtures were measured. On the basis of the obtained results, the components and parameters of oleic, linoleic, and linolenic acids’ surface tension were determined and compared to those of the canola oil. Next, applying the components and parameters of these acids, their adhesion work to PTFE, PMMA, and the engine valve was calculated by means of various methods.

Spreading-Droplet Simulation With Surface Tension Model Using Inter-Particle Force in Particle Method

2013 ◽  
Author(s):  
Eiji Ishii ◽  
Taisuke Sugii
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Dynamic Contact Angle ◽  
Particle Method ◽  
Dynamic Contact ◽  
Contact Angles ◽  
Particle Methods ◽  
Static Contact ◽  
Particle Force ◽  
Surface Tension Model

Predicting the spreading behavior of droplets on a wall is important for designing micro/nano devices used for reagent dispensation in micro-electro-mechanical systems, printing processes of ink-jet printers, and condensation of droplets on a wall during spray forming in atomizers. Particle methods are useful for simulating the behavior of many droplets generated by micro/nano devices in practical computational time; the motion of each droplet is simulated using a group of particles, and no particles are assigned in the gas region if interactions between the droplets and gas are weak. Furthermore, liquid-gas interfaces obtained from the particle method remain sharp by using the Lagrangian description. However, conventional surface tension models used in the particle methods are used for predicting the static contact angle at a three-phase interface, not for predicting the dynamic contact angle. The dynamic contact angle defines the shape of a spreading droplet on a wall. We previously developed a surface tension model using inter-particle force in the particle method; the static contact angle of droplets on the wall was verified at various contact angles, and the heights of droplets agreed well with those obtained theoretically. In this study, we applied our surface tension model to the simulation of a spreading droplet on a wall. The simulated dynamic contact angles for some Weber numbers were compared with those measured by Šikalo et al, and they agreed well. Our surface tension model was useful for simulating droplet motion under static and dynamic conditions.

Tailoring Surface Hydrophobicity of Commercial Polyimide by Laser-Induced Nanocarbon Texturing

2020 ◽  
Vol 8 (3) ◽  
Author(s):  
Moataz Abdulhafez ◽  
Angela J. McComb ◽  
Mostafa Bedewy
Keyword(s):  
Contact Angle ◽  
Surface Characterization ◽  
Surface Engineering ◽  
Processing Parameters ◽  
Surface Hydrophobicity ◽  
Spot Size ◽  
Contact Angles ◽  
Water Contact ◽  
Wide Range ◽  
Surface Nanostructure

Abstract The growth of laser-induced nanocarbons, referred to here as laser-induced nanocarbon (LINC) for short, directly on polymeric surfaces is a promising route toward surface engineering of commercial polymers. This paper aims to demonstrate how this new approach can enable achieving varied surface properties based on tuning the nanostructured morphology of the formed graphitic material on commercial polyimide (Kapton) films. We elucidate the effects of tuning laser processing parameters on the achieved nanoscale morphology and the resulting surface hydrophobicity or hydrophilicity. Our results show that by varying lasing power, rastering speed, laser spot size, and line-to-line gap sizes, a wide range of water contact angles are possible, i.e., from below 20 deg to above 110 deg. Combining water contact angle measurements from an optical tensiometer with LINC surface characterization using optical microscopy, electron microscopy, and Raman spectroscopy enables building the process–structur–property relationship. Our findings reveal that both the value of contact angle and the anisotropic wetting behavior of LINC on polyimide are dependent on their hierarchical surface nanostructure which ranges from isotropic nanoporous morphology to fibrous morphology. Results also show that increasing gap sizes lead to an increase in contact angles and thus an increase in the hydrophobicity of the surface. Hence, our work highlight the potential of this approach for manufacturing flexible devices with tailored surfaces.

Measurements of the Contact Angles for Various Fluids Which Are Widely Used in the Oilfields to Improve Oil Recovery

2018 ◽  
Author(s):  
M. Elsharafi ◽  
K. Vidal ◽  
R. Thomas
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Dynamic Contact Angle ◽  
Dynamic Contact ◽  
Contact Angles ◽  
Rock Face ◽  
Angle Measurements ◽  
Contact Angle Measurements

Contact angle measurements are important to determine surface and interfacial tension between solids and fluids. A ‘water-wet’ condition on the rock face is necessary in order to extract oil. In this research, the objectives are to determine the wettability (water-wet or oil-wet), analyze how different brine concentrations will affect the wettability, and study the effect of the temperature on the dynamic contact angle measurements. This will be carried out by using the Cahn Dynamic Contact Angle. Analyzer DCA 315 to measure the contact angle between different fluids such as surfactant, alkaline, and mineral oil. This instrument is also used to measure the surface properties such as surface tension, contact angle, and interfacial tension of solid and liquid samples by using the Wilhelmy technique. The work used different surfactant and oil mixed with different alkaline concentrations. Varying alkaline concentrations from 20ml to 1ml were used, whilst keeping the surfactant concentration constant at 50ml.. It was observed that contact angle measurements and surface tension increase with increased alkaline concentrations. Therefore, we can deduce that they are directly proportional. We noticed that changing certain values on the software affected our results. It was found that after calculating the density and inputting it into the CAHN software, more accurate readings for the surface tension were obtained. We anticipate that the surfactant and alkaline can change the surface tension of the solid surface. In our research, surfactant is desirable as it maintains a high surface tension even when alkaline percentage is increased.

Sign in / Sign up

Export Citation Format

Share Document