scholarly journals Numerical Investigation on Dynamic Response of RC T-Beams Strengthened with CFRP under Impact Loading

Crystals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 890
Author(s):  
Huiling Zhao ◽  
Xiangqing Kong ◽  
Ying Fu ◽  
Yihan Gu ◽  
Xuezhi Wang
Keyword(s):  
Numerical Simulation ◽  
Impact Force ◽  
Reaction Force ◽  
Impact Resistance ◽  
Structural Response ◽  
Element Model ◽  
Strengthening Effect ◽  
Strengthened Beam ◽  
Simulation Results ◽  
The Impact

To precisely evaluate the retrofitting effectiveness of Carbon Fiber Reinforced Plastic (CFRP) sheets on the impact response of reinforced concrete (RC) T-beams, a non-linear finite element model was developed to simulate the structural response of T-beams with CFRP under impact loads. The numerical model was firstly verified by comparing the numerical simulation results with the experimental data, i.e., impact force, reaction force, and mid-span displacement. The strengthening effect of CFRP was analyzed from the section damage evaluation. Then the impact force, mid-span displacement, and failure mode of CFRP-strengthened RC T-beams were studied in comparison with those of un-strengthened T-beams. In addition, the influence of the impact resistance of T-beams strengthened with FRP was investigated in terms of CFRP strengthening mode, CFRP strengthening sizes, CFRP layers and FRP material types. The numerical simulation results indicate that the overall stiffness of the T-beams was improved significantly due to external CFRP strips. Compared with the un-strengthened beam, the maximum mid-span displacement of the CFRP-strengthened beam was reduced by 7.9%. Additionally, the sectional damage factors of the whole span of the CFRP-strengthened beam were reduced to less than 0.3, indicating that the impact resistance of the T-beams was effectively enhanced.

Study of Ship-Ice Collision on Ice Breaker ARAON

2014 ◽  
Author(s):  
Sungchan Kim ◽  
Insik Nho ◽  
Takkee Lee ◽  
Kyungsik Choi
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Impact Force ◽  
Structural Response ◽  
Element Model ◽  
Design Data ◽  
Complex Process ◽  
The Impact ◽  
Interaction Behaviors ◽  
Ship Speed

The interaction between a ship and sea ice is a complex process depending on the ice properties, the ice geometry and the relative velocity between the ship and the ice. The effect of important parameters such as ship speed and ice thickness on the impact force are studied by means of finite element model. Idealized ice element types are applied to finite element model in order to survey the impact force and the structural response of icebreaker ARAON subjected to sea ices. Interaction behaviors obtained by finite element model considering the varying parameters are also discussed to compare the numerical results with the design data of ARAON.

scholarly journals Dynamic Finite Element Analysis of a New Type Flexible Rock Shed under the Impact of Rock Block and Improving the Design

2018 ◽  
Vol 2018 ◽  
pp. 1-16 ◽  
Author(s):  
Lianming Cui ◽  
Min Wang ◽  
Tangrong Yu
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Impact Analysis ◽  
Numerical Models ◽  
Element Model ◽  
Functional Evaluation ◽  
Element Analysis ◽  
Simulation Results ◽  
Improved Design ◽  
The Impact

A 1:1 flexible rock shed made of flexible nets and steel-vaulted structure is manufactured and tested for functional evaluation with impact experiment previously. To further discuss the performance of this structure under the impact of rockfalls and to improve the design, numerical simulation for this structure is carried out in this paper. Firstly, the simplified numerical models for characterizing the mechanical behavior of the ring nets and wire meshes are deduced. Then, a detailed finite element model for the flexible rock shed is developed for impact analysis. By comparing the experimental data, the numerical model for the flexible rock shed is shown to be reliable in predicting the dynamic behavior of the flexible rock shed. Finally, combined with the numerical simulation results and experimental results, an improved design is presented, and the numerical simulation results show that the energy dispersion in the improved design of the rock shed is more equalized, and damages on the steel-vaulted structure are much improved.

scholarly journals Optimization design of scraper angle based on orthogonal test

2018 ◽  
Vol 175 ◽  
pp. 02005
Author(s):  
Can Wang ◽  
Yuanbin Fang ◽  
Song Huang ◽  
Guizhi Zhang ◽  
Qingyu Meng ◽  
...  
Keyword(s):  
Optimization Design ◽  
Impact Force ◽  
Simulation Analysis ◽  
Element Model ◽  
Orthogonal Test ◽  
Average Force ◽  
Evaluation Indexes ◽  
Simulation Results ◽  
Back Angle ◽  
The Impact

The scraper angle of milling machine has a direct effect on the milling efficiency. This research establishes the finite element model of scraper, and designs the cutting front angle and the cutting back angle as factor, impact force and the average force for orthogonal test of evaluation indexes. Through simulation analysis, the force is obtained at the different level. At the same time, the simulation results are verified by experiments. The results show that the simulation results of contact force in the X direction are close to the measured results, and prove the accuracy of the simulation results. The optimized scraper is that the cutting angle is 5.5°, and the cutting back angle is 9°. The impact force is minimum, and the resultant of average force and impact force is minimum. The optimization of scraper angle can effectively reduce the impact force and the average force, which provides guidance for the improvement of scraper.

Numerical Simulation of Multi-Angle Incidence Aluminum Composite Targets with 7.62mm Piercing Armor

2014 ◽  
Vol 602-605 ◽  
pp. 562-565
Author(s):  
Yu Lei Li ◽  
Jin Jun Tang ◽  
Xiao Yu Jin ◽  
Qun Wang ◽  
Zheng Ren
Keyword(s):  
Numerical Simulation ◽  
Aluminum Alloy ◽  
Material Model ◽  
Element Model ◽  
Target Plate ◽  
Aluminum Composite ◽  
3D Finite Element ◽  
Aluminum Target ◽  
Simulation Results ◽  
The Impact

To calculate the multi-angle penetration, this paper established a 3D finite element model of aluminum alloy plates and 7.62mm armor-piercing by using LS-DYNA software and the Johnson-Cook material model. The process of bullet penetrating 20mm thickness target with different angles of incidence was carried out. The impact of combinations on composite targets resistance projectile penetrating ability was analyzed. Simulation results show that,ballistic of composite targets can be between two aluminum target plate, clearly different combinations of composite targets for resistance to different angles of incidence between projectile penetrating relationship.

scholarly journals Sandwich panel with in-plane honeycombs in different Poisson's ratio under low to medium impact loads

2021 ◽  
Vol 60 (1) ◽  
pp. 145-157
Author(s):  
Yi Luo ◽  
Ke Yuan ◽  
Lumin Shen ◽  
Jiefu Liu
Keyword(s):  
Poisson’S Ratio ◽  
Sandwich Panel ◽  
Impact Force ◽  
Impact Resistance ◽  
Poisson's Ratio ◽  
Compression Performance ◽  
Post Impact ◽  
Local Impact ◽  
Collapse Behavior ◽  
The Impact

Abstract In this study, a series of in-plane hexagonal honeycombs with different Poisson's ratio induced by topological diversity are studied, considering re-entrant, semi-re-entrant and convex cells, respectively. The crushing strength of honeycomb in terms of Poisson's ratio is firstly presented. In the previous research, we have studied the compression performance of honeycomb with different negative Poisson's ratio. In this study, a comparative study on the local impact resistance of different sandwich panels is conducted by considering a spherical projectile with low to medium impact speed. Some critical criteria (i.e. local indentation profile, global deflection, impact force and energy absorption) are adopted to analyze the impact resistance. Finally, an influential mechanism of Poisson's ratio on the local impact resistance of sandwich panel is studied by considering the variation of core strength and post-impact collapse behavior.

scholarly journals Numerical Simulation and Experimental Study on Axial Stiffness and Stress Deformation of the Braided Corrugated Hose

2021 ◽  
Vol 11 (10) ◽  
pp. 4709
Author(s):  
Dacheng Huang ◽  
Jianrun Zhang
Keyword(s):  
Numerical Simulation ◽  
Geometric Model ◽  
Equivalent Stress ◽  
Element Model ◽  
Maximum Error ◽  
Structural Features ◽  
Axial Stiffness ◽  
Frictional Stress ◽  
Maximum Equivalent Stress ◽  
Simulation Results

To explore the mechanical properties of the braided corrugated hose, the space curve parametric equation of the braided tube is deduced, specific to the structural features of the braided tube. On this basis, the equivalent braided tube model is proposed based on the same axial stiffness in order to improve the calculational efficiency. The geometric model and the Finite Element Model of the DN25 braided corrugated hose is established. The numerical simulation results are analyzed, and the distribution of the equivalent stress and frictional stress is discussed. The maximum equivalent stress of the braided corrugated hose occurs at the braided tube, with the value of 903MPa. The maximum equivalent stress of the bellows occurs at the area in contact with the braided tube, with the value of 314MPa. The maximum frictional stress between the bellows and the braided tube is 88.46MPa. The tensile experiment of the DN25 braided corrugated hose is performed. The simulation results are in good agreement with test data, with a maximum error of 9.4%, verifying the rationality of the model. The study is helpful to the research of the axial stiffness of the braided corrugated hose and provides the base for wear and life studies on the braided corrugated hose.

Investigation on penetration model of shaped charge jet in water

2016 ◽  
Vol 30 (02) ◽  
pp. 1550268 ◽  
Author(s):  
Jinwei Shi ◽  
Xingbai Luo ◽  
Jinming Li ◽  
Jianwei Jiang
Keyword(s):  
Numerical Simulation ◽  
Theoretical Model ◽  
Model Simulation ◽  
Theoretical Models ◽  
Theoretical Research ◽  
Water Medium ◽  
Simulation Results ◽  
Jet Penetration ◽  
The Impact ◽  
Penetration Velocity

To analyze the process of jet penetration in water medium quantitatively, the properties of jet penetration spaced target with water interlayer were studied through test and numerical simulation. Two theoretical models of jet penetration in water were proposed. The theoretical model 1 was established considering the impact of the shock wave, combined with the shock equation Rankine–Hugoniot and the virtual origin calculation method. The theoretical model 2 was obtained by fitting theoretical analysis and numerical simulation results. The effectiveness and universality of the two theoretical models were compared through the numerical simulation results. Both the models can reflect the relationship between the penetration velocity and the penetration distance in water well, and both the deviation and stability of theoretical model 1 are better than 2, the lower penetration velocity, and the larger deviation of the theoretical model 2. Therefore, the theoretical model 1 can reflect the properties of jet penetration in water effectively, and provide the reference of model simulation and theoretical research.

Numerical Modeling of Multi-Frequency Complex Dielectric Permittivity Dispersion of Sedimentary Rocks

Geophysics ◽  
2021 ◽  
pp. 1-69
Author(s):  
Artur Posenato Garcia ◽  
Zoya Heidari
Keyword(s):  
Numerical Simulation ◽  
Dielectric Permittivity ◽  
Numerical Simulations ◽  
Dielectric Response ◽  
Water Saturation ◽  
Pore Scale ◽  
Simulation Results ◽  
Wet Rocks ◽  
Permittivity Measurements ◽  
The Impact

The dielectric response of rocks results from electric double layer (EDL), Maxwell-Wagner (MW), and dipolar polarizations. The EDL polarization is a function of solid-fluid interfaces, pore water, and pore geometry. MW and dipolar polarizations are functions of charge accumulation at the interface between materials with contrasting impedances and the volumetric concentration of its constituents, respectively. However, conventional interpretation of dielectric measurements only accounts for volumetric concentrations of rock components and their permittivities, not interfacial properties such as wettability. Numerical simulations of dielectric response of rocks provides an ideal framework to quantify the impact of wettability and water saturation ( Sw) on electric polarization mechanisms. Therefore, in this paper we introduce a numerical simulation method to compute pore-scale dielectric dispersion effects in the interval from 100 Hz to 1 GHz including impacts of pore structure, Sw, and wettability on permittivity measurements. We solve the quasi-electrostatic Maxwell's equations in three-dimensional (3D) pore-scale rock images in the frequency domain using the finite volume method. Then, we verify simulation results for a spherical material by comparing with the corresponding analytical solution. Additionally, we introduce a technique to incorporate α-polarization to the simulation and we verify it by comparing pore-scale simulation results to experimental measurements on a Berea sandstone sample. Finally, we quantify the impact of Sw and wettability on broadband dielectric permittivity measurements through pore-scale numerical simulations. The numerical simulation results show that mixed-wet rocks are more sensitive than water-wet rocks to changes in Sw at sub-MHz frequencies. Furthermore, permittivity and conductivity of mixed-wet rocks have weaker and stronger dispersive behaviors, respectively, when compared to water-wet rocks. Finally, numerical simulations indicate that conductivity of mixed-wet rocks can vary by three orders of magnitude from 100 Hz to 1 GHz. Therefore, Archie’s equation calibrated at the wrong frequency could lead to water saturation errors of 73%.

Influence of Engine Cabin Simplification on Aerodynamic Characteristics of Car

2014 ◽  
Vol 1042 ◽  
pp. 188-193 ◽  
Author(s):  
Xing Jun Hu ◽  
Jing Chang
Keyword(s):  
Numerical Simulation ◽  
Aerodynamic Drag ◽  
Aerodynamic Characteristics ◽  
Thin Plates ◽  
Average Thickness ◽  
Two Dimensional ◽  
Engine Cooling ◽  
Aerodynamic Drag Coefficient ◽  
Simulation Results ◽  
The Impact

In order to analyze the impact of engine cabin parts on aerodynamic characteristics, the related parts are divided into three categories except the engine cooling components: front thin plates (average thickness of 2mm), bottom-suspension and interior panels. The aerodynamic drag coefficient (Cd) were obtained upon the combination schemes consisting of the three types of parts by numerical simulation. Results show that Cd by simulation is closer to the test value gained by the wind tunnel experiment when front thin plates were simplified to the two-dimensional interface with zero thickness. The error is only 5.23%. Meanwhile this scheme reduces grid numbers, thus decreasing the calculating time. As the front thin plates can guide the flow, there is no difference on the Cd values gained from the model with or without bottom-suspension or interior panels when the engine cabin contains the front thin plates; while only both bottom-suspension and interior panels are removed, the Cd value can be reduced when the cabin doesn’t contain the front thin plates.

Numerical Simulation and Analysis on the Impact Effect of Cylindrical Projectile Impacting Shelled Explosive

2013 ◽  
Vol 710 ◽  
pp. 320-324
Author(s):  
Ying Zi Jiang ◽  
Wei Li Wang ◽  
Xue Feng Huang ◽  
Lei Fu ◽  
Zhuang Qing Fan
Keyword(s):  
Numerical Simulation ◽  
Energy Criterion ◽  
Critical Energy ◽  
Simplified Model ◽  
Initiation Point ◽  
4340 Steel ◽  
Simulation Results ◽  
The Impact ◽  
Explosive Detonation ◽  
Critical Initiation

The numerical simulation of shelled Comp.B explosive was studied following the Lee-Tarver ignition and growth model when it was impacted respectively by 4340 Steel, OFHC and 93#W projectile with the same mass; the influences on explosive detonation of the initiation process, the material of projectile and the L/D ratio of projectile were analyzed; the critical initiation speeds of the projectiles of three different materials with different L/D ratio were gained. In order to verify the simulation results, the questions were calculated by the theoretical simplified model, the results of the theoretical calculation and the numerical simulation accorded well based on critical energy criterion. The results show that the capability of igniting explosive, the first is 93#W, the second is OFHC, the last is 4340 Steel; The initiation point were not on the interface of shell and explosive, and the faster of the impacting velocity, the initiation point closer the interface; the bigger of the L/D ratio of projectile, the higher of the critical initiation speed.

Sign in / Sign up

Export Citation Format

Share Document