scholarly journals An E-Band 21-dB Variable-Gain Amplifier with 0.5-V Supply in 40-nm CMOS

Electronics ◽  
2021 ◽  
Vol 10 (7) ◽  
pp. 804
Author(s):  
Gibeom Shin ◽  
Kyunghwan Kim ◽  
Kangseop Lee ◽  
Hyun-Hak Jeong ◽  
Ho-Jin Song
Keyword(s):  
Power Consumption ◽  
Frequency Band ◽  
Noise Figure ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Operating Frequency ◽  
Variable Gain Amplifier ◽  
Variable Gain ◽  
Operating Frequency Band ◽  
Shunt Capacitors

This paper presents a variable-gain amplifier (VGA) in the 68–78 GHz range. To reduce DC power consumption, the drain voltage was set to 0.5 V with competitive performance in the gain and the noise figure. High-Q shunt capacitors were employed at the gate terminal of the core transistors to move input matching points for easy matching with a compact transformer. The four stages amplifier fabricated in 40-nm bulk complementary metal oxide semiconductor (CMOS) showed a peak gain of 24.5 dB at 71.3 GHz and 3‑dB bandwidth of more than 10 GHz in 68–78 GHz range with approximately 4.8-mW power consumption per stage. Gate-bias control of the second stage in which feedback capacitances were neutralized with cross-coupled capacitors allowed us to vary the gain by around 21 dB in the operating frequency band. The noise figure was estimated to be better than 5.9 dB in the operating frequency band from the full electromagnetic (EM) simulation.

A NOVEL LOW-VOLTAGE CMOS VARIABLE GAIN AMPLIFIER WITH GAIN-INDEPENDENT INPUT IMPEDANCE MATCHING FOR DTV TUNING APPLICATIONS

2009 ◽  
Vol 18 (06) ◽  
pp. 1119-1136 ◽  
Author(s):  
S. M. REZAUL HASAN
Keyword(s):  
Frequency Band ◽  
Low Voltage ◽  
Noise Figure ◽  
Supply Voltage ◽  
Impedance Matching ◽  
Variable Gain Amplifier ◽  
Control Voltage ◽  
Cmos Process ◽  
Process Technology ◽  
Variable Gain

This paper presents a novel low-voltage single stage CMOS RF Variable Gain Amplifier (RFVGA) designed in 130 nm IBM CMOS process technology using current feed-back gain-independent impedance matching. The proposed RFVGA has a nearly constant gain over the 400 MHz–1 GHz frequency band. Also, it has a 70 dB gain variation (-40 dB to 30 dB) which is decibel-linear within this frequency band for a control voltage in the range of 0.41 V–0.81 V. The RFVGA demonstrates high linearity (THD ≈ -60 dB) and noise immunity (average Noise Figure ≤ 6 dB). It has an input referred third-order intercept point (IIP3) of -1.5 dBm, and an input reflection coefficient (S11) under -8 dB within the frequency band of interest. Also, it dissipates around 5 mW using a 1.2 V power supply. Further, Monte Carlo simulations incorporating process, supply voltage and temperature variations (PVT variations) as well as mismatch between devices (based on width and length of devices) indicate that the design is quite robust. The proposed RFVGA is highly suitable for mobile digital television (DTV) tuner applications.

A Fully Differential Variable Gain Amplifier for Portable Impedance Sensing Applications

2019 ◽  
Vol 7 ◽  
Author(s):  
Jorge Pérez Bailón ◽  
Jaime Ramírez-Angulo ◽  
Belén Calvo ◽  
Nicolás Medrano
Keyword(s):  
Power Consumption ◽  
Active Area ◽  
Variable Gain Amplifier ◽  
Cmos Process ◽  
Current Steering ◽  
Impedance Sensing ◽  
Variable Gain ◽  
Fully Differential ◽  
Sensing Applications ◽  
Constant Bandwidth

This paper presents a Variable Gain Amplifier (VGA) designed in a 0.18 μm CMOS process to operate in an impedance sensing interface. Based on a transconductance-transimpedance (TC-TI) approach with intermediate analog-controlled current steering, it exhibits a gain ranging from 5 dB to 38 dB with a constant bandwidth around 318 kHz, a power consumption of 15.5 μW at a 1.8 V supply and an active area of 0.021 mm2.

Design of Low Power Integrated CMOS Potentiometric Biosensor for Direct Electronic Detection of DNA Hybridization

2014 ◽  
Vol 67 (1) ◽  
Author(s):  
Wong How Hwan ◽  
Vinny Lam Siu Fan ◽  
Yusmeeraz Yusof
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Dna Hybridization ◽  
Point Of Care ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Channel Length ◽  
Electrical Signal ◽  
Oxide Semiconductor ◽  
Detection Circuit

The purpose of this research is to design a low power integrated complementary metal oxide semiconductor (CMOS) detection circuit for charge-modulated field-effect transistor (CMFET) and it is used for the detection of deoxyribonucleic acid (DNA) hybridization. With the available CMOS technology, it allows the realization of complete systems which integrate the sensing units and transducing elements in the same device. Point-of-care (POC) testing device is a device that allows anyone to operate anywhere and obtain immediate results. One of the important features of POC device is low power consumption because it is normally battery-operated. The power consumption of the proposed integrated CMOS detection circuit requires only 14.87 mW. The detection circuit will amplify the electrical signal that comes from the CMFET to a specified level in order to improve the recording characteristics of the biosensor. Self-cascode topology was used in the drain follower circuit in order to reduce the channel length modulation effect. The proposed detection circuit was designed with 0.18µm Silterra CMOS fabrication process and simulated under Cadence Simulation Tool. 

scholarly journals A Multiband Printed Log-Periodic Dipole Array for Wireless Communications

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Giovanni Andrea Casula ◽  
Paolo Maxia
Keyword(s):  
Wireless Communications ◽  
Radiation Pattern ◽  
Frequency Band ◽  
Stop Band ◽  
Operating Frequency ◽  
Frequency Bands ◽  
Operating Frequency Band ◽  
Input Matching ◽  
Compact Size ◽  
Cst Microwave Studio

A multiband printed Log-periodic dipole array (LPDA) antenna for wireless communications is presented. The antenna has been designed starting from Carrel’s theory, optimized using CST Microwave Studio 2012, and then realized. The comparison between simulated and measured results shows that the proposed antenna can be used for wireless communications both in the S (2.4–3 GHz) and in the C (5.2–5.8 GHz) frequency bands, with very good input matching and a satisfactory end-fire radiation pattern. Moreover, it has a compact size, is very easy to realize, and presents an excellent out-of-band rejection, without the use of stop-band filters, thus avoiding interference out of its operating frequency band.

Tunable Balanced Bandpass Filter with High Common-mode Suppression Based on SLSRs

Frequenz ◽  
2017 ◽  
Vol 71 (11-12) ◽  
Author(s):  
Feng Wei ◽  
Xin Yi Wang ◽  
Dun Wei Liao ◽  
Xiao Wei Shi
Keyword(s):  
Frequency Band ◽  
Design Theory ◽  
Bandpass Filter ◽  
Design Procedure ◽  
Operating Frequency ◽  
Differential Mode ◽  
Common Mode ◽  
Operating Frequency Band ◽  
Mode Suppression ◽  
Transition Structures

AbstractA tunable balanced bandpass filter (BPF) with a good common-mode (CM) suppression based on slotline resonators is proposed in this letter. Two novel stub-loaded slotline resonators (SLSRs) terminated with varactors are designed to obtain tunable differential-mode (DM) responses. It is found that a high and wideband CM suppression can be achieved by employing balanced stepped-impedance microstrip-slotline transition structures. Moreover, the DM passbands are independent from the CM ones, which can significantly simplify the design procedure. To validate the design theory, a compact tunable balanced BPF with an operating frequency band ranging from 3.09 GHz to 3.6 GHz is designed and fabricated. The measured results are found to agree well with the simulated ones.

scholarly journals Design and Simulation Study of Active Baluns Circuits for WiMAX Applications

2019 ◽  
Vol 7 (1) ◽  
Author(s):  
Frederick Ray I. Gomez ◽  
John Richard E. Hizon ◽  
Maria Theresa G. De Leon
Keyword(s):  
Phase Difference ◽  
Simulation Study ◽  
Noise Figure ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Common Source ◽  
Cmos Process ◽  
Common Gate ◽  
Active Balun

The paper presents a design and simulation study of three active balun circuits implemented in a standard 90nm Complementary Metal-Oxide Semiconductor (CMOS) process namely: (1) common-source/drain active balun; (2) common-gate with common-source active balun; and (3) differential active balun.  The active balun designs are intended for Worldwide Interoperability for Microwave Access (WiMAX) applications operating at frequency 5.8GHz and with supply voltage of 1V.  Measurements are taken for parameters such as gain difference, phase difference, and noise figure.  All designs achieved gain difference of less than 0.23dB, phase difference of 180° ± 7.1°, and noise figure of 7.2–9.85dB, which are comparable to previous designs and researches.  Low power consumption attained at the most 4.45mW.

Sign in / Sign up

Export Citation Format

Share Document