scholarly journals Experimental Investigation on the Post-Peak Short-Term and Creep Behavior of Fractured Sandstone

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 598
Author(s):  
Yijiang Zong ◽  
Lijun Han ◽  
Yuhao Jin ◽  
Weisheng Zhao ◽  
Lingdong Meng
Keyword(s):  
Mechanical Behavior ◽  
Failure Modes ◽  
Shear Failure ◽  
High Stress ◽  
Confining Pressure ◽  
Short Term ◽  
Creep Failure ◽  
Creep Tests ◽  
Differential Stress ◽  
Fractured Sandstone

Short-term and creep tests of fractured sandstone with different degrees of damage prepared using pre-peak and post-peak unloading tests on intact sandstone were carried out using a servo-controlled rock mechanics system. Based on our experimental results, the influence of confining pressure and damage on short-term mechanical behavior of fractured sandstone with different degrees of damage was first analyzed. The results show that the peak strength, residual strength, elastic modulus, and secant modulus of fractured sandstone increase linearly with increasing confining pressure, but decrease with increasing damage. The short-term failure modes depend on the damage and change from typical shear failure modes to multiple shear failure modes with increasing damage. Then, the influence of the differential stress, confining pressure, and the degree of damage on the creep mechanical behavior of fractured specimens was further investigated. The axial instantaneous strain and creep strain increase linearly with increasing differential stress, and the specimens exhibit significant time-dependent behavior under high stress. The steady creep rate increases with increasing stress, but it decreases with increasing confining pressure and damage. However, the long-term strength and creep failure strength of fractured specimens increase linearly with increasing confining pressure, but they decrease linearly with increasing damage. The creep failure modes of fractured specimens are also the main shear failure modes, which are similar to the short-term failure modes.

scholarly journals Experimental Study on the Mechanical Behavior of Yunnan Limestone in Natural and Saturated States

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Xutao Zhang ◽  
Mingyang Ren ◽  
Zhaobo Meng ◽  
Baoliang Zhang ◽  
Jinglong Li
Keyword(s):  
Elastic Modulus ◽  
Mechanical Behavior ◽  
Water Content ◽  
Failure Modes ◽  
Shear Failure ◽  
Mechanical Response ◽  
Deformation Modulus ◽  
Confining Pressure ◽  
Hyperbolic Function ◽  
Test Results

Rock material is a kind of mineral assemblage with complex structural heterogeneity, whose mechanical behavior is strongly affected by water or moisture content. In this work, we carried out a series of laboratory tests to investigate the mechanical response (e.g., deformation, strength, and failure characteristics) of Yunnan limestone in natural and saturated states. Our test results show that (1) after saturation, the stiffness and strength of Yunnan limestone degenerate considerably. Compared with the natural condition, the elastic modulus, deformation modulus, and tensile modulus decrease by about 30% on average, and uniaxial compressive strength and tensile strength also decrease by about 15% and 20%, respectively. While Poisson’s ratio is less affected by water content, it can be regarded as a constant; (2) the elastic modulus and deformation modulus of Yunnan limestone are significantly affected by confining pressure, and the relationship between them and confining pressure satisfies the law of hyperbolic function; (3) the peak strength envelope of Yunnan limestone has significant nonlinear characteristics, which can be well described by generalized Hoek-Brown strength criterion. However, the generalized Hoek-Brown criterion does not apply to the residual strength, which shows a linearly increasing trend with the increasing confining pressure; (4) the failure modes of Yunnan limestone are significantly dependent on confining pressure but insensitive to water content. With the increasing confining pressure, the failure modes of Yunnan limestone transform from splitting failure, tension-shear mixed failure, single inclined plane shear failure to Y-shaped or X-shaped conjugated shear failure. The test results can provide important experimental data for the establishment of the constitutive model of Yunnan limestone, which will contribute to obtain more reliable results for stability assessment of Xianglu Mountain Tunnel.

scholarly journals Experimental Study on the Short-Term Uniaxial Creep Characteristics of Sandstone-Coal Composite Samples

Minerals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1398
Author(s):  
Dawei Yin ◽  
Feng Wang ◽  
Jicheng Zhang ◽  
Faxin Li ◽  
Chun Zhu ◽  
...  
Keyword(s):  
Creep Strain ◽  
Stress Level ◽  
Creep Strength ◽  
Creep Deformation ◽  
Shear Failure ◽  
Composite Sample ◽  
Short Term ◽  
Creep Failure ◽  
Creep Tests ◽  
Composite Samples

In this investigation, the uniaxial short-term creep tests with multi-step loading were conducted on the sandstone-coal composite samples, and the characteristics of creep strength, creep deformation, acoustic emission (AE), and creep failure of composite samples were studied, respectively. The creep strength of the composite sample decreased with the stress-level duration, which was mainly determined by the coal and influenced by the interactions with the sandstone. The creep deformation and damage of sandstone weakened the deformation and damage accumulation within the coal, resulting in the larger strength for the composite sample compared with the pure coal sample. The axial creep strain of composite sample generally increased with the stress-level or the stress-level duration under same conditions. The AE characteristics of composite sample were related to the creep strain rate, the stress level, the stress level duration, and the local failure or fracture during creep loading. The micro or macro failure and fracture within the composite sample caused the rise in the axial creep strains and the frequency and intensity of AE signals, especially the macro failure and fracture. The creep failures of composite samples mainly occurred within the coal with the splitting ejection failure accompanied by the local shear failure, and no obvious failures were found within the sandstone. The coal in the composite sample became more broken with the stress-level duration.

scholarly journals Cracking Behaviors and Mechanical Properties of Rock-Like Specimens with Two Unparallel Flaws under Conventional Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Chenghua Xu ◽  
Liuyang Li ◽  
Yong Liu
Keyword(s):  
Mechanical Properties ◽  
Inclination Angle ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Critical Value ◽  
Tensile Failure ◽  
Rock Bridge ◽  
Bridge Length

Flaws existing in rock masses are generally unparallel and under three-dimensional stress; however, the mechanical and cracking behaviors of the specimens with two unparallel flaws under triaxial compression have been rarely studied. Therefore, this study conducted comprehensive research on the cracking and coalescence behavior and mechanical properties of specimens with two unparallel flaws under triaxial compression. Triaxial compressive tests were conducted under different confining pressures on rock-like specimens with two preexisting flaws but varying flaw geometries (with respect to the inclination angle of the two unparallel flaws, rock bridge length, and rock bridge inclination angle). Six crack types and eleven coalescence types in the bridge region were observed, and three types of failure modes (tensile failure, shear failure, and tensile-shear failure) were observed in experiments. Test results show that bridge length and bridge inclination angle have an effect on the coalescence pattern, but the influence of bridge inclination angle is larger than that of the bridge length. When the confining pressure is low, coalescence patterns and failure modes of the specimens are greatly affected by flaw geometry, but when confining pressure rose to a certain level, the influence of confining pressure is larger than the effect of flaw geometry. The peak strength of the specimens is affected by flaw geometry and confining pressure. There is a critical value for the bridge length. If the bridge length is larger than the critical value, peak strengths of the samples almost keep constant as the bridge length increases. In addition, as the bridge inclination angle increases, there is an increase in the probability of tensile cracks occurring, and with an increase in the confining pressure, the probability of the occurrence of shear cracks increases.

Short-term retrospective forecasting of earthquakes based on temporal variations of the b-value of the magnitude-frequency distribution

2020 ◽  
Author(s):  
Paolo Gasperini ◽  
Emanuele Biondini ◽  
Antonio Petruccelli ◽  
Barbara Lolli ◽  
Gianfranco Vannucci
Keyword(s):  
Frequency Distribution ◽  
High Probability ◽  
High Stress ◽  
B Value ◽  
Temporal Variations ◽  
Short Term ◽  
Differential Stress ◽  
B Values ◽  
Probability Of Occurrence ◽  
Seismic Catalog

<p>In some recent works it has been hypothesized that the slope (b-value) of the magnitude-frequency distribution of earthquakes may be related to the differential stress inside the crust.  In particular, it has been observed that low b-values are associated with high stress values and therefore with high probability of occurrence of strong seismic shocks. In this paper we formulate a predictive hypothesis based on temporal variations of the b-value. We tested and optimized such hypothesis retrospectively based on the homogenized Italian instrumental seismic catalog (HORUS) from 1995 to 2018. A comparison is also made with a similar predictive hypothesis based on the occurrence of strong foreshocks.</p><p> </p>

scholarly journals Cut-Through Fractured Seepage Properties and Numerical Simulation of Sandstone after Different Temperature Treatments

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Haopeng Jiang ◽  
Annan Jiang
Keyword(s):  
Fracture Surface ◽  
Shear Failure ◽  
Failure Surface ◽  
Confining Pressure ◽  
Theoretical Formula ◽  
Negative Exponential Function ◽  
Damage Degree ◽  
Different Temperatures ◽  
Negative Exponential ◽  
Fractured Sandstone

To explore the seepage characteristics of cut-through fractured rocks after different temperatures, sandstone in the Hunan area was selected as the research object. First, the influence degree of different temperatures on the permeability of fractured sandstone was studied, and the permeability variation of fractured sandstone with net confining pressure was revealed. The test data was nonlinearly fitted to prove that the relationship between permeability and net confining pressure conforms to the characteristics of the negative exponential function. Second, the macroscopic fractured state of sandstone after different temperature treatments was analyzed, and it is concluded that the inclination angle of the fracture surface decreases with the applied thermal temperature, the fracture surface gradually develops into a single shear failure surface, and the damage degree becomes more and more serious. Finally, the theoretical formula for the calculation of fractured seepage was introduced, and the FLAC3D embedded fish language was used to compile the seepage-stress coupling calculation program of the fractured sandstone after different temperature treatments. Numerical calculations were carried out based on samples with different fracture angles of fractured sandstone, and the calculated values were in good agreement with the test results. The research results can provide guiding significance for the research on the influence of high temperature in fire tunnel on the evolution of permeability of surrounding rock fissures.

Injection-induced seismicity: strategies for reducing risk using high stress path reservoirs and temperature-induced stress preconditioning

2019 ◽  
Vol 220 (2) ◽  
pp. 1436-1446 ◽  
Author(s):  
B Fryer ◽  
G Siddiqi ◽  
L Laloui
Keyword(s):  
Seismic Event ◽  
Shear Failure ◽  
High Stress ◽  
Stress Path ◽  
B Value ◽  
Large Magnitude ◽  
Differential Stress ◽  
Induced Stress ◽  
Reverse Faulting ◽  
New Strategy

SUMMARY It is suggested that fluid injection in normal faulting stress regimes can stabilize a reservoir if the stress path is high enough. This stabilization is not seen when the reservoir is significantly cooled as a result of injection. Further, a new strategy is suggested for stimulating reservoirs in shear with a reduced chance of inducing a large magnitude seismic event. The version of this methodology presented here is applicable for reverse faulting stress regimes and involves an initial stress preconditioning stage where the reservoir is cooled and the pressure increase is limited. This process reduces the horizontal total stress and thereby also the differential stress. Next, the reservoir is stimulated with a rapid increase in pore pressure, resulting in shear failure at a lower differential stress than was initially present in the reservoir. Due to the connection seen between the Gutenberg–Richter b-value and differential stress, it is suggested that reservoirs stimulated in this fashion will exhibit higher b-values and thereby also have a reduced chance of hosting a large magnitude event. It is suggested that adaptations of this methodology are applicable to both normal and strike-slip faulting stress regimes.

scholarly journals Experimental Investigation on Failure Modes and Mechanical Properties of Rock-Like Specimens with a Grout-Infilled Flaw under Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Feng Zhu ◽  
Haotian Fan
Keyword(s):  
Mechanical Properties ◽  
Rock Mass ◽  
Epoxy Resin ◽  
Failure Modes ◽  
Shear Failure ◽  
Fractured Rock ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Compression Tests

Flaws existing in rock mass are one of the main factors resulting in the instability of rock mass. Epoxy resin is often used to reinforce fractured rock mass. However, few researches focused on mechanical properties of the specimens with a resin-infilled flaw under triaxial compression. Therefore, in this research, epoxy resin was selected as the grouting material, and triaxial compression tests were conducted on the rock-like specimens with a grout-infilled flaw having different geometries. This study draws some new conclusions. The high confining pressure suppresses the generation of tensile cracks, and the failure mode changes from tensile-shear failure to shear failure as the confining pressure increases. Grouting with epoxy resin leads to the improvement of peak strengths of the specimens under triaxial compression. The reinforcement effect of epoxy resin is better for the specimens having a large flaw length and those under a relatively low confining pressure. Grouting with epoxy resin reduces the internal friction angle of the samples but improves their cohesion. This research may provide some useful insights for understanding the mechanical behaviors of grouted rock masses.

scholarly journals Particle Flow Simulation of the Strength and Failure Characteristics of a Layered Composite Rock-Like Sample with a Single Hole

Symmetry ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1132
Author(s):  
Guozhu Wang ◽  
Yu Wang ◽  
Lei Song ◽  
Hao Shi ◽  
Mingwei Zhang ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Failure Mode ◽  
Failure Modes ◽  
Shear Failure ◽  
Surrounding Rock ◽  
Tensile Failure ◽  
Practical Significance ◽  
Rock Masses ◽  
Engineering Structures ◽  
Layered Rock

Layered rock masses with holes are common in nature. Their mechanical behavior plays an important role in the safety and stability of engineering structures. However, previous studies have concentrated on a single lithological layer, and few studies have reported on the mechanical behavior of layered rock masses with holes. Based on the concept of symmetry, uniaxial compression tests and numerical simulations were performed on rock-like specimens with three layers and a hole in the interlayer. The hole was in the center of the sample and was symmetrical up and down. The influence of the thickness and strength of the interlayer on the mechanical behavior and failure processes of the layered rock masses with holes was investigated. The results show that the peak strength and elastic modulus were associated with the thickness and strength of the interlayer. Three failure modes were observed in the specimens, which were not only related to the thickness and strength of the interlayer, but also affected by the presence of the hole. When the thickness of the interlayer is small, mainly a single failure mode was observed (tensile failure or shear failure). However, when the interlayer was thick, the failure mode was tension-shear mixed failure. The failure mechanism of the specimens was primarily crack propagation at the edge of the hole. These research results can provide a basis for site selection, and the design of surrounding rock protection and support parameters, and thus have important practical significance for improving surrounding rock stability and ensuring construction safety.

scholarly journals Long-term creep behavior of deep-buried marble under different confining pressures

2019 ◽  
Vol 23 (Suppl. 3) ◽  
pp. 653-660
Author(s):  
Ersheng Zha ◽  
Ru Zhang ◽  
Zetian Zhang ◽  
Li Ren ◽  
Wenju Zhang ◽  
...  
Keyword(s):  
Creep Behavior ◽  
Shear Failure ◽  
Confining Pressure ◽  
Tensile Failure ◽  
Creep Failure ◽  
Failure Characteristics ◽  
Underground Caverns ◽  
Confining Pressures ◽  
Term Creep

To explore the long-term creep behavior of deep rock, the long-term tri-axial creep mechanical behavior of the rock under different confining pressures has been carried out. The results show that the instantaneous strain and creep strain of the high confining pressure specimen are significantly higher than that of the low confining pressure specimen under high deviatoric stress. By analyzing the failure characteristics of different confining pressure specimens, it is found that with the increase of the confining pressure, the creep failure characteristics of the marble transforms from tensile failure to shear failure. These research results have certain reference significance for the long-term stability analysis of the deep underground caverns.

scholarly journals Experimental Study on the Mechanical Properties and Seepage Characteristics of Red Sandstone with a Single Persistent Joint under Triaxial Compression

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Wei Wang ◽  
Shifan Liu ◽  
Chong Shi ◽  
Shanxi Zheng ◽  
Qizhi Zhu
Keyword(s):  
Mechanical Properties ◽  
Pore Pressure ◽  
Failure Modes ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Strengthening Effect ◽  
Red Sandstone ◽  
Inclination Angles ◽  
Seepage Characteristics

In this research, the conventional triaxial compression experiments for intact red sandstone specimens and the specimens with a single persistent joint at different inclination angles, i.e., 0°, 30°, 45°, and 90°, were conducted at first. Based on the results of the conventional tests, the effects of the confining pressure and the joint inclination angle on the mechanical properties including deformation behavior and strength parameters were summarized and analyzed, respectively. We find that the strength and deformation of jointed red sandstone are enlarged due to the increment of confining pressure, and the mechanical parameters of specimens show a U-shaped development with the rise of the joint angle. Besides, to investigate the effects of the pore pressure on seepage characteristics of rocks with joint angles at 0°, 45°, and 90°, a series of triaxial compression drainage tests on the jointed red sandstone were performed. The results show that the pore pressure has a weakening effect on the strength of jointed specimens, which can reduce the strengthening effect induced by confining pressure. Meanwhile, the tested specimens mostly present shear failure modes. As a result, the mechanical responses, seepage characteristics, and cracking modes in red sandstone containing a single persistent joint under triaxial compression are revealed.

Sign in / Sign up

Export Citation Format

Share Document