scholarly journals Adjusting the Single-Diode Model Parameters of a Photovoltaic Module with Irradiance and Temperature

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3226 ◽  
Author(s):  
Nader Anani ◽  
Haider Ibrahim
Keyword(s):  
Numerical Technique ◽  
Standard Test ◽  
Climatic Conditions ◽  
Operating Conditions ◽  
Photovoltaic Module ◽  
Model Parameters ◽  
Pv System ◽  
Pv Module ◽  
Test Conditions ◽  
Parameter Modification

This paper presents a concise discussion and an investigation of the most literature-reported methods for modifying the lumped-circuit parameters of the single-diode model (SDM) of a photovoltaic (PV) module, to suit the prevailing climatic conditions of irradiance and temperature. These parameters provide the designer of a PV system with an essential design and simulation tool to maximize the efficiency of the system. The parameter modification methods were tested using three commercially available PV modules of different PV technologies, namely monocrystalline, multicrystalline, and thin film types. The SDM parameters of the three test modules were extracted under standard test conditions (STC) using a well-established numerical technique. Using these STC parameters as reference values, the parameter adjustment methods were subsequently deployed to calculate the modified parameters of the SDM under various operating conditions of temperature and irradiance using MATLAB-based software. The accuracy and effectiveness of these methods were evaluated by a comparison between the calculated and measured values of the modified parameters.

scholarly journals TEMPERATURE AND IRRADIANCE BASED ANALYSIS THE SPECIFIC VARIATION OF PV MODULE

2021 ◽  
Vol 83 (6) ◽  
pp. 1-17
Author(s):  
Mohsin Ali Koondhar ◽  
Irfan Ali Channa ◽  
Sadullah Chandio ◽  
Muhammad Ismail Jamali ◽  
Abdul Sami Channa ◽  
...  
Keyword(s):  
Iterative Methods ◽  
Standard Test ◽  
Operating Conditions ◽  
Back Surface ◽  
Photovoltaic Module ◽  
Solar Module ◽  
Pv Module ◽  
Test Conditions ◽  
Specific Variation ◽  
Module Efficiency

The effect of irradiance and increase of temperature on the back surface of the PV module would decrease the standardized efficiency of PV. To overcome this problem observed results of solar module (ORSM) and Newton Raphson’s (iterative) methods have been proposed in this research. This article compares ORSM and iterative methods of changing the specifications of a single diode model (SDM) extracted from a PV module beneath standard test conditions (STC) to calculate irradiance and various operating conditions. To make this comparison, the exact value of each diode parameter on the STC is essential. These are achieved by accepted algebraic values and iterative techniques. Newton Raphson’s technique has been proven to be the mainly precise method to find these specifications in STC. Therefore, these specifications are used to different techniques that change the parameters of an SDM with radiation and temperature. The MATLAB model is designed to assess the conducting of individual techniques by PVM. The results are compared with the measured data, and the accuracy of photovoltaic module efficiency has been achieved through different technologies at different temperature and insolation levels.

scholarly journals A model for predicting photovoltaic module performances

2019 ◽  
Vol 10 (4) ◽  
pp. 1914
Author(s):  
Nadia Bouaziz ◽  
Arezki Benfdila ◽  
Ahcene Lakhlef
Keyword(s):  
Environmental Parameters ◽  
Operating Conditions ◽  
Solar Irradiation ◽  
Photovoltaic Module ◽  
Physical Parameters ◽  
Solar Pv ◽  
Site Location ◽  
Pv System ◽  
Pv Module ◽  
Mathematical Expressions

The present paper deals with the development of a simulation model for predicting the performances of a solar photovoltaic (PV) system operating under current meteorological conditions at the site location. The proposed model is based on the cell equivalent circuit including a photocurrent source, a diode, a series and shunt resistances. Mathematical expressions developed for modeling the PV generator performances are based on current-voltage characteristic of the considered modules. The developed model allows the prediction of PV cell (module) behavior under different physical and environmental parameters. The model can be extended to extract physical parameters for a given solar PV module as a function of temperature and solar irradiation. A typical 260 W solar panel developed by LG Company was used for model evaluation using Newton-Raphson approach under MATLAB environment in order to analyze its behavior under actual operating conditions. Comparison of our results with data taken from the manufacturer’s datasheet shows good agreement and confirms the validity of our model. Hence, the proposed approach can be an alternative to extract different parameters of any PV module to study and predict its performances.

scholarly journals Improved Hybrid Parameters Extraction of a PV Module Using a Moth Flame Algorithm

Electronics ◽  
2021 ◽  
Vol 10 (22) ◽  
pp. 2798
Author(s):  
Safi Allah Hamadi ◽  
Aissa Chouder ◽  
Mohamed Mounir Rezaoui ◽  
Saad Motahhir ◽  
Ameur Miloud Kaddouri
Keyword(s):  
Extraction Procedure ◽  
Parameter Extraction ◽  
Standard Test ◽  
Maximum Power ◽  
Model Parameters ◽  
Unknown Parameters ◽  
Operating Condition ◽  
Pv Module ◽  
Test Conditions ◽  
Parameters Extraction

The identification of actual photovoltaic (PV) model parameters under real operating condition is a crucial step for PV engineering. An accurate and trusted model depends mainly on the accuracy of the model parameters. In this paper, an accurate and enhanced methodology is intended for PV module parameters extraction in outdoor conditions. The proposed methodology combines numerical methods and analytical formulations of the one diode model to derive the five unknown parameters in any operating condition of irradiance and temperature. First, the measured I-V curves at a random weather condition are translated to standard test conditions (i.e., G = 1000 W/m2, T = 25 °C), using translation equations. The second step consists of using an optimization algorithm namely the moth flame algorithm (MFO) to find out the five parameters at standard test conditions. Analytical formulations, at a random irradiance and temperature, are then used to express the unknown parameters at any irradiance and temperature. The proposed approach is validated under outdoor conditions against measured I-V curves at different irradiances and temperatures. The validation has also been performed under dynamic operation where the measured maximum power point coordinates (MPP) are compared to the predicted maximum power points. The obtained results from the adopted hybrid methodology confirm the accuracy of the parameter extraction procedure.

scholarly journals Analysis of Power Generation for Solar Photovoltaic Module with Various Internal Cell Spacing

2021 ◽  
Vol 13 (11) ◽  
pp. 6364
Author(s):  
June Raymond L. Mariano ◽  
Yun-Chuan Lin ◽  
Mingyu Liao ◽  
Herchang Ay
Keyword(s):  
Power Output ◽  
Spacing Effect ◽  
Photovoltaic Cell ◽  
Standard Test ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Engineering Software ◽  
Internal Cell ◽  
Cell Spacing ◽  
Pv Module

Photovoltaic (PV) systems directly convert solar energy into electricity and researchers are taking into consideration the design of photovoltaic cell interconnections to form a photovoltaic module that maximizes solar irradiance. The purpose of this study is to evaluate the cell spacing effect of light diffusion on output power. In this work, the light absorption of solar PV cells in a module with three different cell spacings was studied. An optical engineering software program was used to analyze the reflecting light on the backsheet of the solar PV module towards the solar cell with varied internal cell spacing of 2 mm, 5 mm, and 8 mm. Then, assessments were performed under standard test conditions to investigate the power output of the PV modules. The results of the study show that the module with an internal cell spacing of 8 mm generated more power than 5 mm and 2 mm. Conversely, internal cell spacing from 2 mm to 5 mm revealed a greater increase of power output on the solar PV module compared to 5 mm to 8 mm. Furthermore, based on the simulation and experiment, internal cell spacing variation showed that the power output of a solar PV module can increase its potential to produce more power from the diffuse reflectance of light.

scholarly journals An Improved Generalized Method for Evaluation of Parameters, Modeling, and Simulation of Photovoltaic Modules

2017 ◽  
Vol 2017 ◽  
pp. 1-19 ◽  
Author(s):  
Vandana Jha ◽  
Uday Shankar Triar
Keyword(s):  
Modeling And Simulation ◽  
Standard Test ◽  
Unknown Parameters ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Test Conditions ◽  
Pv Modules ◽  
Evaluation Of Parameters ◽  
Output Characteristics ◽  
Matlab Programming

This paper proposes an improved generalized method for evaluation of parameters, modeling, and simulation of photovoltaic modules. A new concept “Level of Improvement” has been proposed for evaluating unknown parameters of the nonlinear I-V equation of the single-diode model of PV module at any environmental condition, taking the manufacturer-specified data at Standard Test Conditions as inputs. The main contribution of the new concept is the improvement in the accuracy of values of evaluated parameters up to various levels and is based on mathematical equations of PV modules. The proposed evaluating method is implemented by MATLAB programming and, for demonstration, by using the values of parameters of the I-V equation obtained from programming results, a PV module model is build with MATLAB. The parameters evaluated by the proposed technique are validated with the datasheet values of six different commercially available PV modules (thin film, monocrystalline, and polycrystalline) at Standard Test Conditions and Nominal Operating Cell Temperature Conditions. The module output characteristics generated by the proposed method are validated with experimental data of FS-270 PV module. The effects of variation of ideality factor and resistances on output characteristics are also studied. The superiority of the proposed technique is proved.

Lifetime Estimation of a Photovoltaic Module Subjected to Corrosion Due to Damp Heat Testing

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
R. Laronde ◽  
A. Charki ◽  
D. Bigaud
Keyword(s):  
Crystalline Silicon ◽  
Meteorological Data ◽  
Photovoltaic Module ◽  
Model Parameters ◽  
Solar Panels ◽  
Power Requirement ◽  
Pv Module ◽  
Accelerated Life ◽  
Mean Lifetime ◽  
Initial Power

In this paper, a methodology is presented for estimating the lifetime of a photovoltaic (PV) module. Designers guarantee an acceptable level of power (80% of the initial power) up to 25 yr for solar panels without having sufficient feedback to validate this lifetime. Accelerated life testing (ALT) can be carried out in order to determine the lifetime of the equipment. Severe conditions are used to accelerate the ageing of components and the reliability is then deduced in normal conditions, which are considered to be stochastic rather than constant. Environmental conditions at normal operations are simulated using IEC 61725 standard and meteorological data. The mean lifetime of a crystalline-silicon photovoltaic module that meets the minimum power requirement is estimated. The main results show the influence of lifetime distribution and Peck model parameters on the estimation of the lifetime of a photovoltaic module.

Effect of Unglazed Transpired Collector on the Performance of a Polycrystalline Silicon Photovoltaic Module

2006 ◽  
Vol 128 (3) ◽  
pp. 349-353 ◽  
Author(s):  
A. T. Naveed ◽  
E. C. Kang ◽  
E. J. Lee
Keyword(s):  
Polycrystalline Silicon ◽  
Electrical Power ◽  
Heating System ◽  
Photovoltaic Module ◽  
Forced Ventilation ◽  
Pv System ◽  
Pv Module ◽  
Pv Modules ◽  
Typical Day ◽  
Electrical Output

The electrical power generated by a polycrystalline silicon photovoltaic (PV) module mounted on an unglazed transpired solar collector (UTC) has been studied and compared to that of a PV module without UTC for a quantitative analysis of electrical output and its role in reducing the simple payback periods of photovoltaic electrical systems. A 75W polycrystalline silicon PV module was fixed on an UTC in front of the ventilation fan, and effectiveness of cooling by means of the forced ventilation at the rate of 160CFM was monitored. The temperature reduction under forced ventilation was in the range of 3-9°C with a 5% recovery in the electrical output power on a typical day of the month of February 2005. The simulated and measured electrical power outputs are in reasonable agreement with root-mean-square error of 2.40. The life cycle assessment of a hypothetical PV system located at Daejeon, South Korea and consisting of 3kW PV modules fixed on a 50m2 UTC shows that with a possible reduction of 3-9°C in the operating temperatures, the system requires three 75W fewer PV modules. The simple payback period of PV system is reduced from 23yearsto15years when integrated into an UTC air heating system.

scholarly journals Modeling of Photovoltaic Module Using the MATLAB

2019 ◽  
Vol 9 ◽  
pp. 59-69
Author(s):  
Alok Dhaundiyal ◽  
Divine Atsu
Keyword(s):  
Standard Test ◽  
Electrical Performance ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Pv Module ◽  
Proposed Model ◽  
Current Voltage ◽  
Pv Modules ◽  
The Impact ◽  
The Mathematical Model

This paper presents the modeling and simulation of the characteristics and electrical performance of photovoltaic (PV) solar modules. Genetic coding is applied to obtain the optimized values of parameters within the constraint limit using the software MATLAB. A single diode model is proposed, considering the series and shunt resistances, to study the impact of solar irradiance and temperature on the power-voltage (P-V) and current-voltage (I-V) characteristics and predict the output of solar PV modules. The validation of the model under the standard test conditions (STC) and different values of temperature and insolation is performed, as well as an evaluation using experimentally obtained data from outdoor operating PV modules. The obtained results are also subjected to comply with the manufacturer’s data to ensure that the proposed model does not violate the prescribed tolerance range. The range of variation in current and voltage lies in the domain of 8.21 – 8.5 A and 22 – 23 V, respectively; while the predicted solutions for current and voltage vary from 8.28 – 8.68 A and 23.79 – 24.44 V, respectively. The measured experimental power of the PV module estimated to be 148 – 152 W is predicted from the mathematical model and the obtained values of simulated solution are in the domain of 149 – 157 W. The proposed scheme was found to be very effective at determining the influence of input factors on the modules, which is difficult to determine through experimental means.

scholarly journals Temperature impact on dusty and cleaned photovoltaic module exposed in sub-Saharan outdoor conditions

2018 ◽  
Vol 9 ◽  
pp. 8 ◽  
Author(s):  
N'detigma Kata ◽  
Y. Moussa Soro ◽  
Djicknoum Diouf ◽  
Arouna Darga ◽  
A. Seidou Maiga
Keyword(s):  
Standard Test ◽  
Operating Conditions ◽  
Solar Irradiation ◽  
Test Facility ◽  
Photovoltaic Module ◽  
Significant Drop ◽  
Single Junction ◽  
Irradiation Level ◽  
Sub Saharan ◽  
Module Performance

In this work, impacts of temperature and dust cleaning on photovoltaic module performance operating in sub-Saharan's climate are investigated. Two single junction technologies, monocrystalline and polycrystalline silicon, and one micromorph (amorphous/micrystalline) thin film silicon tandem technology are considered. We have recorded at the same time under real operating conditions, the module temperature and the current versus voltage characteristics of each module, and the local solar irradiation. All the measurements were performed with the outdoor monitoring and test facility located at Ouagadougou in Burkina Faso. The results show the drop of generated power of dusty modules for the same irradiation level. Between April and June (where temperatures are higher) a significant drop of output power is observed, despite a daily cleaning. Furthermore, performance losses are observed for all technologies compared to that under standard test conditions. However, the micromorph silicon tandem technology with low temperature sensitivity present the less losses in performance compared to the monocrystalline and the polycrystalline single junction modules, even if the modules are not cleaned.

scholarly journals Performance Evaluation of Analytical Methods for Parameters Extraction of Photovoltaic Generators

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4825 ◽  
Author(s):  
Nader Anani ◽  
Haider Ibrahim
Keyword(s):  
Performance Evaluation ◽  
Computational Complexity ◽  
Numerical Methods ◽  
Analytical Methods ◽  
Standard Test ◽  
Pv Module ◽  
Test Conditions ◽  
Parameters Extraction ◽  
Detailed Mathematical Analysis ◽  
Photovoltaic Generators

This paper presents a succinct exploration of several analytical methods for extracting the parameters of the single-diode model (SDM) of a photovoltaic (PV) module under standard test conditions (STC). The paper investigates six methods and presents the detailed mathematical analysis leading to the development of each method. To evaluate the performance of these methods, MATLAB-based software has been devised and deployed to generate the results of each method when used to extract the SDM parameters of various PV test modules of different PV technologies. Similar software has also been developed to extract the same parameters using well-established numerical and iterative techniques. A comparison is subsequently made between the synthesized results and those obtained using numerical and iterative methods. The comparison indicates that although analytical methods may involve a significant amount of approximations, their accuracy can be comparable to that of their numerical and iterative counterparts, with the added advantage of a significant reduction in computational complexity, and without the initialization and convergence difficulties, which are normally associated with numerical methods.

Sign in / Sign up

Export Citation Format

Share Document