scholarly journals Influence of Gas Flooding Pressure on Groundwater Flow during Oil Shale In Situ Exploitation

Energies ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 8363
Author(s):  
Lihong Yang ◽  
Zhao Liu ◽  
Hao Zeng ◽  
Jianzheng Su ◽  
Yiwei Wang ◽  
...  
Keyword(s):  
Groundwater Flow ◽  
Oil Shale ◽  
Windward Side ◽  
Water Yield ◽  
Leeward Side ◽  
Production Well ◽  
Spot Pattern ◽  
Gas Flooding ◽  
One To One

In order to weaken the influence of external groundwater on in situ pyrolysis exploitation, the flow characteristics of groundwater were studied according to the oil shale reservoir characteristics of Qingshankou Formation in Songliao Basin, China. In addition, the parameters of marginal gas flooding for water-stopping were optimized. Taking a one-to-one pattern and a five-spot pattern as examples, the characteristics of groundwater flow under the in situ process were studied. Under the one-to-one pattern, the external groundwater flows into the production well from the low-pressure side, and the water yield was basically stable at 1000 kg/d. In the five-spot pattern, the groundwater can flow into the production wells directly from the windward side, and the water yield of the production well on the leeward side mainly comes from the desaturated zone; the water yield of each production well remains at a high level. By setting water-stopping wells around the production well and keeping the gas flooding pressure slightly higher than the production well, the water yield of the production well can be reduced and stabilized within 100 kg/d under gas flooding pressures of 3 and 5 MPa. However, the gas yield of the production well slightly decreased when the gas flooding pressure reduced from 5 to 3 MPa. Therefore, the gas flooding pressure of water-stopping wells shall be determined in combination with the water yield and gas yield, so as to achieve the best process effect. It is expected that the results will provide technical support for large-scale oil shale in situ pyrolysis exploitation.

Research on Underground Dynamic Fluid Pressure Balance in the Process of Oil Shale In-Situ Fracturing-Nitrogen Injection Exploitation

2017 ◽  
Vol 139 (3) ◽  
Author(s):  
Chen Chen ◽  
Shuai Gao ◽  
Youhong Sun ◽  
Wei Guo ◽  
Qiang Li
Keyword(s):  
High Pressure ◽  
Field Experiment ◽  
Ground Water ◽  
Oil Shale ◽  
Dynamic Pressure ◽  
Nitrogen Pressure ◽  
Production Well ◽  
Pressure Balance ◽  
Nitrogen Injection

Oil shale in-situ retorting is a reasonable development technology. However, the ground water may flow into fractures in oil shale layer that impact the process of oil shale in-situ retorting. This paper introduced oil shale in-situ fracturing-nitrogen injection exploitation and a method of dynamic pressure balance between the ground water and high pressure nitrogen to keep the oil shale layer without ground water in the process of oil shale in-situ fracturing-nitrogen injection exploitation. Theoretical basis of dynamic pressure balance between ground water and nitrogen was established through analyzing pressure relationship between ground water and nitrogen in the fractures and field experiment was conducted according to the method. The field experiment results showed that nitrogen pressure maintained high level in the fractures during the stage of building pressure balance of nitrogen and ground water and pushed ground water out of the oil shale layer. Then, nitrogen pressure in the fractures reduced and maintained stable because part of nitrogen in the fractures flowed out from the production well and flow conductivity of fractures enhanced. After the balance between the ground water and high pressure nitrogen was established, water yield of production well reduced more than 85%. It explained that the balance has function of sealing up.

Controlling groundwater infiltration by gas flooding for oil shale in situ pyrolysis exploitation

2019 ◽  
Vol 179 ◽  
pp. 444-454 ◽  
Author(s):  
Youhong Sun ◽  
Zhao Liu ◽  
Qiang Li ◽  
Sunhua Deng ◽  
Wei Guo
Keyword(s):  
Oil Shale ◽  
Gas Flooding ◽  
Groundwater Infiltration

Spectro-mechanical Characterization of Aromaticity and Maturity of Kerogens in Oil Shale at 6 nm Spatial Resolution

2018 ◽  
Author(s):  
Devon Jakob ◽  
Le Wang ◽  
Haomin Wang ◽  
Xiaoji Xu
Keyword(s):  
Spatial Resolution ◽  
Oil Shale ◽  
Infrared Imaging ◽  
Mechanical Characterization ◽  
Optical Diffraction ◽  
Chemical Compositions ◽  
Valuable Insight ◽  
Eagle Ford Shale

<p>In situ measurements of the chemical compositions and mechanical properties of kerogen help understand the formation, transformation, and utilization of organic matter in the oil shale at the nanoscale. However, the optical diffraction limit prevents attainment of nanoscale resolution using conventional spectroscopy and microscopy. Here, we utilize peak force infrared (PFIR) microscopy for multimodal characterization of kerogen in oil shale. The PFIR provides correlative infrared imaging, mechanical mapping, and broadband infrared spectroscopy capability with 6 nm spatial resolution. We observed nanoscale heterogeneity in the chemical composition, aromaticity, and maturity of the kerogens from oil shales from Eagle Ford shale play in Texas. The kerogen aromaticity positively correlates with the local mechanical moduli of the surrounding inorganic matrix, manifesting the Le Chatelier’s principle. In situ spectro-mechanical characterization of oil shale will yield valuable insight for geochemical and geomechanical modeling on the origin and transformation of kerogen in the oil shale.</p>

scholarly journals Cyclic Subcritical Water Injection into Bazhenov Oil Shale: Geochemical and Petrophysical Properties Evolution Due to Hydrothermal Exposure

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4570
Author(s):  
Aman Turakhanov ◽  
Albina Tsyshkova ◽  
Elena Mukhina ◽  
Evgeny Popov ◽  
Darya Kalacheva ◽  
...  
Keyword(s):  
Energy Demand ◽  
Oil Shale ◽  
Oil And Gas ◽  
Subcritical Water ◽  
Pore Space ◽  
Water Injection ◽  
Microstructural Properties ◽  
Gas Generation ◽  
Geochemical Parameters

In situ shale or kerogen oil production is a promising approach to developing vast oil shale resources and increasing world energy demand. In this study, cyclic subcritical water injection in oil shale was investigated in laboratory conditions as a method for in situ oil shale retorting. Fifteen non-extracted oil shale samples from Bazhenov Formation in Russia (98 °C and 23.5 MPa reservoir conditions) were hydrothermally treated at 350 °C and in a 25 MPa semi-open system during 50 h in the cyclic regime. The influence of the artificial maturation on geochemical parameters, elastic and microstructural properties was studied. Rock-Eval pyrolysis of non-extracted and extracted oil shale samples before and after hydrothermal exposure and SARA analysis were employed to analyze bitumen and kerogen transformation to mobile hydrocarbons and immobile char. X-ray computed microtomography (XMT) was performed to characterize the microstructural properties of pore space. The results demonstrated significant porosity, specific pore surface area increase, and the appearance of microfractures in organic-rich layers. Acoustic measurements were carried out to estimate the alteration of elastic properties due to hydrothermal treatment. Both Young’s modulus and Poisson’s ratio decreased due to kerogen transformation to heavy oil and bitumen, which remain trapped before further oil and gas generation, and expulsion occurs. Ultimately, a developed kinetic model was applied to match kerogen and bitumen transformation with liquid and gas hydrocarbons production. The nonlinear least-squares optimization problem was solved during the integration of the system of differential equations to match produced hydrocarbons with pyrolysis derived kerogen and bitumen decomposition.

In-situ catalytic co-pyrolysis of kukersite oil shale with black pine wood over acid zeolites

2021 ◽  
Vol 155 ◽  
pp. 105050
Author(s):  
Young-Kwon Park ◽  
Muhammad Zain Siddiqui ◽  
Selhan Karagöz ◽  
Tae Uk Han ◽  
Atsushi Watanabe ◽  
...  
Keyword(s):  
Oil Shale ◽  
Black Pine ◽  
Pine Wood ◽  
Acid Zeolites

Investigation on the drag effect of a rolling element confined in the cavity of a cylindrical roller bearing

2021 ◽  
pp. 135065012110260
Author(s):  
Wenjun Gao ◽  
Shuo Zhang ◽  
Xiaohang Li ◽  
Zhenxia Liu
Keyword(s):  
Open Space ◽  
Roller Bearing ◽  
Flow Characteristics ◽  
Experimental Tests ◽  
Windward Side ◽  
Leeward Side ◽  
Drag Effect ◽  
Rolling Element ◽  
Cylindrical Roller Bearing ◽  
Cylindrical Roller

In cylindrical roller bearings, the drag effect may be induced by the rolling element translating in a fluid environment of the bearing cavity. In this article, the computational fluid dynamics method and experimental tests are employed to analyse its flow characteristics and pressure distribution. The results indicate that the pressure difference between the windward side and the leeward side of the cylinder is raised in view of it blocking the flow field. Four whirl vortexes are formed in four outlets of two wedge-shaped areas between the front part of the cylindrical surface and adjacent walls for the cylinder of L/ D = 1.5 at Re = 4.5 × 103. Vortex shedding is found in the direction of cylinder axis at Re = 4.5 × 104. The relationship between drag coefficient and Reynolds number is illustrated, obviously higher than that of the two-dimensional cylinder in open space.

scholarly journals 2.5D Flexible Wind Sensor Using Differential Plate Capacitors

Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 3101
Author(s):  
Yu Wan ◽  
Zhenxiang Yi
Keyword(s):  
Wind Speed ◽  
Wind Direction ◽  
Parallel Plate ◽  
Electrode Array ◽  
Copper Electrode ◽  
Windward Side ◽  
Leeward Side ◽  
Electrode Layer ◽  
Young’S Moduli ◽  
Speed Up

In this paper, a novel 2.5-dimensional (2.5D) flexible wind sensor is proposed based on four differential plate capacitors. This design consists of a windward pillar, two electrode layers, and a support layer, which are all made of polydimethylsiloxane (PDMS) with different Young’s moduli. A 2 mm × 2 mm copper electrode array is located on each electrode layer, forming four parallel plate capacitors as the sensitive elements. The wind in the xy-plane tilts the windward pillar, decreasing two capacitances on the windward side and increasing two capacitances on the leeward side. The wind in the z-axis depresses the windward pillar, resulting in an increase of all four capacitances. Experiments demonstrate that this sensor can measure the wind speed up to 23.9 m/s and the wind direction over the full 360° range of the xy-plane. The sensitivities of wind speed are close to 4 fF·m−1·s and 3 fF·m−1·s in the xy-plane and z-axis, respectively.

Air movement and heat loss from sheep. II. Thermal insulation of fleece in wind

1980 ◽  
Vol 209 (1175) ◽  
pp. 209-217 ◽  
Keyword(s):  
Thermal Diffusivity ◽  
Heat Loss ◽  
Thermal Insulation ◽  
General Relation ◽  
Windward Side ◽  
Leeward Side ◽  
Sensible Heat ◽  
Bulk Resistance ◽  
Air Movement ◽  
Dimensionless Constant

Penetration of an animal’s coat by wind reduces its thermal insulation and increases heat loss to the environment. From studies of the sensible heat loss from a life-sized model sheep covered with fleece, the average fleece resistance r¯ f (s cm -1 ) was related to windspeed u (m s -1 ) by 1/ r¯ f ( u ) = l/ r¯ f (0) + cu , where c is a dimensionless constant. As c is expected to be inversely proportional to coat depth Î , the more general relation k¯ ( u ) = k¯ (0) + c'u was evaluated, where k¯ = Î / r¯ f is the thermal diffusivity (cm 2 s -1 ) of the fleece and c' = cÎ is another constant (cm). The orientation of the model to the wind had little effect on the bulk resistance of the fleece, but the resistance on the windward side was substantially lower than on the leeward side.

Sign in / Sign up

Export Citation Format

Share Document