scholarly journals Deterioration of the Mechanical Properties of FFF 3D-Printed PLA Structures

Inventions ◽  
2020 ◽  
Vol 6 (1) ◽  
pp. 1
Author(s):  
Asahi Yonezawa ◽  
Akira Yamada
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Test Piece ◽  
Tensile Tests ◽  
Poly Lactic Acid ◽  
Uniaxial Tensile ◽  
Layer By Layer ◽  
Fused Filament Fabrication ◽  
Test Pieces ◽  
3D Printed

Poly(lactic acid) (PLA) is a biodegradable polymer material used for the fabrication of objects by fused filament fabrication (FFF) 3D printing. FFF 3D printing technology has been quickly spreading over the past few years. An FFF-3D-printed object is formed from melted polymer extruded from a nozzle layer-by-layer. The mechanical properties of the object, and the changes in those properties as the object degrades, differ from the properties and changes observed in bulk objects. In this study we evaluated FFF-3D-printed objects by uniaxial tensile tests and four-point flexural tests to characterize the changes of three mechanical properties, namely, the maximum stress, elastic modulus, and breaking energy. Eight types of test pieces printed directly by an FFF 3D printer using two scan patterns and two interior fill percentages (IFPs) were tested by the aforesaid methods. The test pieces were immersed in saline and kept in an incubator at 37 °C for 30, 60, or 90 days before the mechanical testing. The changes in the mechanical properties differed largely between the test piece types. In some of the test pieces, transient increases in strength were observed before the immersion degraded the strength. Several of the test piece types were found to have superior specific strength in the tests. The results obtained in this research will be helpful for the design of PLA structures fabricated by FFF 3D printing.

scholarly journals Poly(Lactic) Acid Reinforced with Alkaline Lignin Biocomposites Prepared by Thermal Extrusion for Sustainable 3D Printing Process

2021 ◽  
Vol 2129 (1) ◽  
pp. 012003
Author(s):  
Nurul Amirah Abd Rahman ◽  
Hazleen Anuar ◽  
Fathilah Ali ◽  
Jonghwan Suhr
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
3D Printing ◽  
Natural Fiber ◽  
Tensile Tests ◽  
Poly Lactic Acid ◽  
Fused Filament Fabrication ◽  
3D Printed ◽  
Functional Components ◽  
Thermal Extrusion

Abstract The focus of this work is the mechanical characterization of biomaterials produced by 3D printing based on fused filament fabrication (FFF) process that has been mainly used for prototype rather than functional components due to the limited mechanical properties of pure thermoplastics parts. Addition of reinforcements from natural fiber has been adopted to improve the mechanical properties of the 3D printed parts. In this study, alkaline lignin powder that has been extracted from oil palm empty fruit bunches (OPEFB) via alkaline extraction process were used as filler in the production of biocomposites with poly(lactic) acid (PLA). Poly(lactic) acid filaments filled with 1% of alkaline lignin powder and has been compared with the presence of 5% of epoxidized palm oil (EPO) by means of thermal extrusion and further proceed with 3D printing. The samples were mechanically characterized using tensile tests and the fractography were observed. Tensile test that has been done on the filaments reveal that the filament with addition of lignin and EPO shows improved mechanical properties with higher tensile strength as well as lower stiffness. The 3D printed samples of the filament compositions also exhibit similar trend where the said filament has the best mechanical properties when the EPO is incorporated in the filament.

scholarly journals Evaluation of the Deterioration of the Mechanical Properties of Poly(lactic acid) Structures Fabricated by a Fused Filament Fabrication 3D Printer

Inventions ◽  
2019 ◽  
Vol 4 (1) ◽  
pp. 21 ◽  
Author(s):  
Miho Suzuki ◽  
Asahi Yonezawa ◽  
Kohei Takeda ◽  
Akira Yamada
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Tensile Tests ◽  
Poly Lactic Acid ◽  
3D Printer ◽  
Fused Filament Fabrication ◽  
Tensile Direction ◽  
Test Pieces ◽  
3D Printers ◽  
Scan Pattern

A fused filament fabrication (FFF) 3D printer is a simple device capable of manufacturing three-dimensional structures in a series of easy steps. Commercial-level FFF 3D printers have spread rapidly in many fields in recent years. Poly(lactic acid) (PLA) is a biodegradable thermoplastic polymer used as a typical printing medium for FFF 3D printers. The FFF printer constructs an object with melted polymer extruded from a tiny scanning nozzle. The mechanical properties of FFF 3D structures printed with different scan patterns can therefore vary in accordance with the directions from which forces act upon them. The nozzle scan pattern also influences the deterioration of the mechanical properties of the structures in accordance with the degradation caused by the hydrolysis of PLA. In this study we conducted tensile tests to evaluate the strength characteristics of 3D printed test pieces formed from PLA using four different scan patterns: parallel, vertical, parallel-and-vertical, and cross-hatched at opposing diagonal angles to the tensile direction. We also formed test pieces by an injection molding method using the same material, for further comparison. We evaluated the deterioration of the test pieces after immersing them in saline for certain periods. After the test pieces formed by different nozzle scan patterns were immersed, they exhibited differences in the rates by which their maximum tensile stresses deteriorated and their masses increased through water uptake. The influences of the scan patterns could be classified into two types: the unidirectional scan pattern influence and bidirectional scan pattern influence. The data obtained in this research will be applied to structural design when the FFF 3D printer is employed for the fabrication of structures with PLA filament.

scholarly journals Metallization of Thermoplastic Polymers and Composites 3D Printed by Fused Filament Fabrication

Technologies ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 49
Author(s):  
Alessia Romani ◽  
Andrea Mantelli ◽  
Paolo Tralli ◽  
Stefano Turri ◽  
Marinella Levi ◽  
...  
Keyword(s):  
Physical Vapor Deposition ◽  
Test Sample ◽  
Tensile Tests ◽  
Layer By Layer ◽  
Post Processing ◽  
Thermoplastic Polymers ◽  
Fused Filament Fabrication ◽  
Scanning Calorimetry ◽  
3D Printed ◽  
Manufacturing Technologies

Fused filament fabrication allows the direct manufacturing of customized and complex products although the layer-by-layer appearance of this process strongly affects the surface quality of the final parts. In recent years, an increasing number of post-processing treatments has been developed for the most used materials. Contrarily to other additive manufacturing technologies, metallization is not a common surface treatment for this process despite the increasing range of high-performing 3D printable materials. The objective of this work is to explore the use of physical vapor deposition sputtering for the chromium metallization of thermoplastic polymers and composites obtained by fused filament fabrication. The thermal and mechanical properties of five materials were firstly evaluated by means of differential scanning calorimetry and tensile tests. Meanwhile, a specific finishing torture test sample was designed and 3D printed to perform the metallization process and evaluate the finishing on different geometrical features. Furthermore, the roughness of the samples was measured before and after the metallization, and a cost analysis was performed to assess the cost-efficiency. To sum up, the metallization of five samples made with different materials was successfully achieved. Although some 3D printing defects worsened after the post-processing treatment, good homogeneity on the finest details was reached. These promising results may encourage further experimentations as well as the development of new applications, i.e., for the automotive and furniture fields.

Tensile properties of the FFF-processed thermoplastic polyurethane (TPU) elastomer

2021 ◽  
Author(s):  
Budi Arifvianto ◽  
Teguh Nur Iman ◽  
Benidiktus Tulung Prayoga ◽  
Rini Dharmastiti ◽  
Urip Agus Salim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Low Cost ◽  
Thermoplastic Polyurethane ◽  
High Strength ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Fused Filament Fabrication ◽  
Raster Angle ◽  
Manufacturing Techniques

Abstract Fused filament fabrication (FFF) has become one of the most popular, practical, and low-cost additive manufacturing techniques for fabricating geometrically-complex thermoplastic polyurethane (TPU) elastomer. However, there are still some uncertainties concerning the relationship between several operating parameters applied in this technique and the mechanical properties of the processed material. In this research, the influences of extruder temperature and raster orientation on the mechanical properties of the FFF-processed TPU elastomer were studied. A series of uniaxial tensile tests was carried out to determine tensile strength, strain, and elastic modulus of TPU elastomer that had been printed with various extruder temperatures, i.e., 190–230 °C, and raster angles, i.e., 0–90°. Thermal and chemical characterizations were also conducted to support the analysis in this research. The results obviously showed the ductile and elastic characteristics of the FFF-processed TPU, with specific tensile strength and strain that could reach up to 39 MPa and 600%, respectively. The failure mechanisms operating on the FFF-processed TPU and the result of stress analysis by using the developed Mohr’s circle are also discussed in this paper. In conclusion, the extrusion temperature of 200 °C and raster angle of 0° could be preferred to be applied in the FFF process to achieve high strength and ductile TPU elastomer.

scholarly journals Parameters Affecting the Mechanical Properties of Three-Dimensional (3D) Printed Carbon Fiber-Reinforced Polylactide Composites

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2456
Author(s):  
Demei Lee ◽  
Guan-Yu Wu
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
3D Printing ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Bed Temperature ◽  
3D Printed ◽  
The Impact

Three-dimensional (3D) printing is a manufacturing technology which creates three-dimensional objects layer-by-layer or drop-by-drop with minimal material waste. Despite the fact that 3D printing is a versatile and adaptable process and has advantages in establishing complex and net-shaped structures over conventional manufacturing methods, the challenge remains in identifying the optimal parameters for the 3D printing process. This study investigated the influence of processing parameters on the mechanical properties of Fused Deposition Modelling (FDM)-printed carbon fiber-filled polylactide (CFR-PLA) composites by employing an orthogonal array model. After printing, the tensile and impact strengths of the printed composites were measured, and the effects of different parameters on these strengths were examined. The experimental results indicate that 3D-printed CFR-PLA showed a rougher surface morphology than virgin PLA. For the variables selected in this analysis, bed temperature was identified as the most influential parameter on the tensile strength of CFR-PLA-printed parts, while bed temperature and print orientation were the key parameters affecting the impact strengths of printed composites. The 45° orientation printed parts also showed superior mechanical strengths than the 90° printed parts.

scholarly journals Effect of Porosity and Crystallinity on 3D Printed PLA Properties

Polymers ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1487 ◽  
Author(s):  
Yuhan Liao ◽  
Chang Liu ◽  
Bartolomeo Coppola ◽  
Giuseppina Barra ◽  
Luciano Di Maio ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Polylactic Acid ◽  
Complex Geometry ◽  
Fused Filament Fabrication ◽  
3D Printed ◽  
Physical Changes ◽  
Crystalline Forms

Additive manufacturing (AM) is a promising technology for the rapid tooling and fabrication of complex geometry components. Among all AM techniques, fused filament fabrication (FFF) is the most widely used technique for polymers. However, the consistency and properties control of the FFF product remains a challenging issue. This study aims to investigate physical changes during the 3D printing of polylactic acid (PLA). The correlations between the porosity, crystallinity and mechanical properties of the printed parts were studied. Moreover, the effects of the build-platform temperature were investigated. The experimental results confirmed the anisotropy of printed objects due to the occurrence of orientation phenomena during the filament deposition and the formation both of ordered and disordered crystalline forms (α and δ, respectively). A heat treatment post-3D printing was proposed as an effective method to improve mechanical properties by optimizing the crystallinity (transforming the δ form into the α one) and overcoming the anisotropy of the 3D printed object.

scholarly journals Optimization of Manufacturing Parameters and Tensile Specimen Geometry for Fused Deposition Modeling (FDM) 3D-Printed PETG

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2556
Author(s):  
Arda Özen ◽  
Dietmar Auhl ◽  
Christina Völlmecke ◽  
Josef Kiendl ◽  
Bilen Emek Abali
Keyword(s):  
Mechanical Properties ◽  
Fused Deposition Modeling ◽  
Tensile Tests ◽  
Tensile Specimen ◽  
Careful Examination ◽  
Uniaxial Tensile ◽  
Fused Deposition ◽  
Design Flexibility ◽  
Deposition Modeling ◽  
3D Printed

Additive manufacturing provides high design flexibility, but its use is restricted by limited mechanical properties compared to conventional production methods. As technology is still emerging, several approaches exist in the literature for quantifying and improving mechanical properties. In this study, we investigate characterizing materials’ response of additive manufactured structures, specifically by fused deposition modeling (FDM). A comparative analysis is achieved for four different tensile test specimens for polymers based on ASTM D3039 and ISO 527-2 standards. Comparison of specimen geometries is studied with the aid of computations based on the Finite Element Method (FEM). Uniaxial tensile tests are carried out, after a careful examination of different slicing approaches for 3D printing. We emphasize the effects of the chosen slicer parameters on the position of failures in the specimens and propose a simple formalism for measuring effective mechanical properties of 3D-printed structures.

scholarly journals Influence of Infill Pattern on the Elastic Mechanical Properties of Fused Filament Fabrication (FFF) Parts through Experimental Tests and Numerical Analyses

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5459
Author(s):  
Jordi Bonada ◽  
Mª Magdalena Pastor ◽  
Irene Buj-Corral
Keyword(s):  
Mechanical Properties ◽  
Manufacturing Process ◽  
Experimental Tests ◽  
Tensile Tests ◽  
Numerical Analyses ◽  
Layer By Layer ◽  
Fused Filament Fabrication ◽  
Element Analysis ◽  
Young’S Moduli ◽  
Printing Parameters

Fused Filament Fabrication (FFF) is one of the most extensive additive manufacturing technologies for printing prototypes or final parts in various fields. Some printed parts need to meet structural requirements to be functional parts. Therefore, it is necessary to know the mechanical behavior of the printed samples as a function of the printing parameters in order to optimize the material used during the manufacturing process. It is known that FFF parts can present orthotropic characteristics as a consequence of the manufacturing process, in which the material is deposited layer by layer. Therefore, these characteristics must be considered for a correct evaluation of the printed parts from a structural point of view. In this paper, the influence of the type of filling pattern on the main mechanical properties of the printed parts is analyzed. For this purpose, the first parts are 3D printed using three different infill patterns, namely grid, linear with a raster orientation of 0 and 90°, and linear with a raster orientation of 45°. Then, experimental tensile tests, on the one hand, and numerical analyses using finite elements, on the other hand, are carried out. The elastic constants of the material are obtained from the experimental tests. From the finite element analysis, using a simple approach to create a Representative Volume Model (RVE), the constitutive characteristics of the material are estimated: Young’s Moduli and Poisson’s ratios of the printed FFF parts. These values are successfully compared with those of the experimental tests. The results clearly show differences in the mechanical properties of the FFF printed parts, depending on the internal arrangement of the infill pattern, even if similar 3D printing parameters are used.

Characterization of PLA/TPU composite filaments manufactured for 3D printing with FDM

2021 ◽  
pp. 089270572110625
Author(s):  
Ajay Jayswal ◽  
Sabit Adanur
Keyword(s):  
3D Printing ◽  
Fused Deposition Modeling ◽  
Thermoplastic Polyurethane ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Mechanical Analysis ◽  
Uniaxial Tensile ◽  
Scanning Calorimetry ◽  
Fused Deposition ◽  
3D Printed

Polylactic acid (PLA) and thermoplastic polyurethane (TPU) were mixed in different proportions and extruded through twin-screw and single-screw extruders to obtain composite filaments to be used for 3D printing with fused deposition modeling (FDM) method. The properties of the filaments were characterized using uniaxial tensile tests, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), rheology, polarized optical microscope (POM), and scanning electron microscope (SEM). 3D printed samples from composite filaments were tested using dynamic mechanical analysis (DMA). It was found that the tensile strength and modulus of the filaments decrease while elongation at break increases with the increasing TPU content in the composite. The analysis also showed a partial miscibility of the polymer constituents in the solution of composite filaments. Finally, a flexible structure, plain weave fabric, was designed and 3D printed using the composite filaments developed which proved that the filaments are well suited for 3D printing.

Sign in / Sign up

Export Citation Format

Share Document