scholarly journals Mechanical and Fire Properties of Multicomponent Flame Retardant EPDM Rubbers Using Aluminum Trihydroxide, Ammonium Polyphosphate, and Polyaniline

Materials ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 1932 ◽  
Author(s):  
Benjamin Zirnstein ◽  
Dietmar Schulze ◽  
Bernhard Schartel
Keyword(s):  
Mechanical Properties ◽  
Flame Retardant ◽  
Cone Calorimeter ◽  
Average Rate ◽  
Multicomponent System ◽  
Ammonium Polyphosphate ◽  
Limiting Oxygen Index ◽  
Epdm Rubber ◽  
The Impact ◽  
Aluminum Trihydroxide

In this study, multicomponent flame retardant systems, consisting of ammonium polyphosphate (APP), aluminum trihydroxide (ATH), and polyaniline (PANI), were used in ethylene propylene diene monomer (EPDM) rubber. The multicomponent system was designed to improve flame retardancy and the mechanical properties of the rubber compounds, while simultaneously reducing the amount of filler. PANI was applied at low loadings (7 phr) and combined with the phosphorous APP (21 phr) and the mineral flame retardant ATH (50 phr). A comprehensive study of six EPDM rubbers was carried out by systematically varying the fillers to explain the impact of multicomponent flame retardant systems on mechanical properties. The six EPDM materials were investigated via the UL 94, limiting oxygen index (LOI), FMVSS 302, glow wire tests, and the cone calorimeter, showing that multicomponent flame retardant systems led to improved fire performance. In cone calorimeter tests the EPDM/APP/ATH/PANI composite reduced the maximum average rate of heat emission (MARHE) to 142 kW·m−2, a value 50% lower than that for the unfilled EPDM rubber. Furthermore, the amount of phosphorus in the residues was quantified and the mode of action of the phosphorous flame retardant APP was explained. The data from the cone calorimeter were used to determine the protective layer effect of the multicomponent flame retardant systems in the EPDM compounds.

Flammability and Mechanical Properties of Toughened Phenolic Foams Containing APP, MP and MCA

2013 ◽  
Vol 671-674 ◽  
pp. 1809-1812
Author(s):  
Shao Hong Xu ◽  
Xiao Yu Sui ◽  
Zheng Zhou Wang
Keyword(s):  
Mechanical Properties ◽  
Thermal Decomposition ◽  
Flame Retardant ◽  
Oxygen Index ◽  
Ammonium Polyphosphate ◽  
Limiting Oxygen Index ◽  
Melamine Cyanurate ◽  
Melamine Phosphate

Flammability of toughened phenolic (PF) foams containing ammonium polyphosphate (APP), melamine phosphate (MP) or melamine cyanurate(MCA) was studied by limiting oxygen index (LOI). The LOI values show that APP or MP is an effient flame retardant than MCA in the toughened PF foams. The thermal decomposition and mechanical properties of the phenolic foams were also investigated.

scholarly journals Basalt Fiber-Based Flame Retardant Epoxy Composites: Preparation, Thermal Properties, and Flame Retardancy

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 902
Author(s):  
Yu Guo ◽  
Meihui Zhou ◽  
Guang-Zhong Yin ◽  
Ehsan Kalali ◽  
Na Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Flame Retardant ◽  
Basalt Fiber ◽  
Mechanical Analysis ◽  
Epoxy Composites ◽  
Cone Calorimetry ◽  
Limiting Oxygen Index ◽  
Pre Treatment ◽  
The Impact

We aimed to study the impact of surface modification of basalt fiber (BF) on the mechanical properties of basalt fiber-based epoxy composites. Four different types of pretreatment approaches to BF were used; then a silane coupling agent (KH550) was applied to further modify the pretreated BF, prior to the preparation of epoxy resin (EP)/BF composites. The combination of acetone (pre-treatment) and KH550 (formal surface treatment) for basalt fiber (BT-AT) imparted the EP/BF composite with the best performance in both tensile and impact strengths. Subsequently, such modified BF was introduced into the flame-retardant epoxy composites (EP/AP750) to prepare basalt fiber reinforced flame-retardant epoxy composite (EP/AP750/BF-AT). The fire behaviors of the composites were evaluated by vertical burning test (UL-94), limiting oxygen index (LOI) test and cone calorimetry. In comparison to the flame-retardant properties of EP/AP750, the incorporation of BF-AT slightly reduced LOI value from 26.3% to 25.1%, maintained the good performance in vertical burning test, but increased the peak of the heat release rate. Besides, the thermal properties and mechanical properties of the composites were investigated by thermogravimetric analysis (TGA), universal tensile test, impact test and dynamic mechanical analysis (DMA).

scholarly journals Rigid Polyurethane Foams Containing Modified Ammonium Polyphosphate Having Outstanding Charring Ability and Increased Flame Retardancy

2021 ◽  
Vol 8 ◽  
Author(s):  
Chunzhuang Yang ◽  
Shuiyu Shao
Keyword(s):  
Mechanical Properties ◽  
Heat Release ◽  
Flame Retardant ◽  
Degree Of Polymerization ◽  
Polyurethane Foams ◽  
Ammonium Polyphosphate ◽  
Cone Calorimeter Test ◽  
Compressive Strength Test ◽  
Flame Retardant Properties ◽  
The Impact

Ammonium polyphosphate (APP) with different polymerization degrees were modified by a novel phosphorus-containing organosilicon compound (PCOC), and the products obtained were coded as MAPP-30 and MAPP-1000. Then they were applied to prepare flame-retardant rigid polyurethane foam (RPUF) separately. The impact of modified APP (MAPP) on the flame-retardant properties of RPUF was investigated by the limited oxygen index (LOI) test, horizontal burning test, and cone calorimeter test. The morphologies of the char residues were observed by SEM. Furthermore, the mechanical properties of RPUF composites were measured by the compressive strength test. The results showed that whether the degree of polymerization of MAPP is 30 or 1000, they both had greater charring ability and better flame-retardant properties than unmodified APP. The residual char yield of RPUF/MAPP-30 (37.3%) and RPUF/MAPP-1000 (36.5%) were both significantly higher than RPUF/APP-30 (22.8%) and RPUF/APP-1000 (24.9%). The peak heat release rate value of RPUF/MAPP-30 was 29.9% lower than that of RPUF/APP-30, and the drop of RPUF/MAPP-1000 was 50.9% compared to RPUF/APP-1000. Moreover, the total heat release of RPUF/MAPP-1000 (9.7 MJ/m2) was much lower than that of RPUF/MAPP-30 (11.3 MJ/m2). In summary, MAPP-1000 has the best flame-retardant properties among all RPUF composites. In addition, the results also showed that flame-retardant performance and the mechanical properties dramatically decreased with the increase in the addition of MAPP-1000, and the RPUF composite had the best comprehensive performance with 20% content of MAPP-1000.

scholarly journals Environmentally Friendly Flame-Retardant and Its Application in Rigid Polyurethane Foam

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Yongjun Chen ◽  
Zhixin Jia ◽  
Yuanfang Luo ◽  
Demin Jia ◽  
Bin Li
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Flame Retardant ◽  
Polyurethane Foam ◽  
Thermal Effects ◽  
Oxygen Index ◽  
Rigid Polyurethane Foam ◽  
Limiting Oxygen Index ◽  
Peak Heat Release Rate ◽  
The Impact

A novel Flame-Retardant N-(P,P′-diphenyl) phosphorus-based-(3-triethoxysilicon) propylamine (DPTP) was synthesized in this study. The impact of DPTP on the mechanical properties, thermal stability, and flame retardancy of rigid polyurethane foam (RPUF) was studied. The addition of DPTP to RPUF can significantly reduce the undesirable thermal effects and smoke density during combustion, as well as increasing the limiting oxygen index. Compared with pure RPUF, the peak heat release rate of RPUF containing 10 phr of DPTP decreased by 39.4%, while its peak smoke production rate decreased by 49.9%. However, it was also found that the addition of DPTP reduced the compressive strength of RPUF.

scholarly journals An Effective Method for Preparation of Liquid Phosphoric Anhydride and Its Application in Flame Retardant Epoxy Resin

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2205
Author(s):  
Qian Li ◽  
Yujie Li ◽  
Yifan Chen ◽  
Qiang Wu ◽  
Siqun Wang
Keyword(s):  
Flame Retardant ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Oxygen Index ◽  
Decomposition Temperature ◽  
Ease Of Use ◽  
Limiting Oxygen Index ◽  
Good Thermal Stability ◽  
Low Viscosity ◽  
The Impact

A novel liquid phosphorous-containing flame retardant anhydride (LPFA) with low viscosity was synthesized from 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) and methyl tetrahydrophthalic anhydride (MeTHPA) and further cured with bisphenol-A epoxy resin E-51 for the preparation of the flame retardant epoxy resins. Both Fourier transform infrared spectroscopy (FT-IR), mass spectrometry (MS) and nuclear magnetic resonance (NMR) measurements revealed the successful incorporation of DOPO on the molecular chains of MeTHPA through chemical reaction. The oxygen index analysis showed that the LPFA-cured epoxy resin exhibited excellent flame retardant performance, and the corresponding limiting oxygen index (LOI) value could reach 31.2%. The UL-94V-0 rating was achieved for the flame retardant epoxy resin with the phosphorus content of 2.7%. With the addition of LPFA, the impact strength of the cured epoxy resins remained almost unchanged, but the flexural strength gradually increased. Meanwhile, all the epoxy resins showed good thermal stability. The glass transition temperature (Tg) and thermal decomposition temperature (Td) of epoxy resin cured by LPFA decreased slightly compared with that of MeTHPA-cured epoxy resin. Based on such excellent flame retardancy, low viscosity at room temperature and ease of use, LPFA showed potential as an appropriate curing agent in the field of electrical insulation materials.

Flame Retardation of Plain Weave Fabrics Made of Polyacrylonitrile Pre-Oxidized Yarns

2011 ◽  
Vol 175-176 ◽  
pp. 465-468 ◽  
Author(s):  
Lei Shi ◽  
Hua Wu Liu ◽  
Ping Xu ◽  
Dang Feng Zhao
Keyword(s):  
Mechanical Properties ◽  
Flame Retardant ◽  
Oxygen Index ◽  
Limiting Oxygen Index ◽  
Plain Weave ◽  
Weave Fabric ◽  
Short Period ◽  
Flame Retardation ◽  
Fabric Structures

Plain weave fabrics of polyacrylonitrile pre-oxidation yarns (PANOF) were prepared by small rapier loom. The flame retardation properties, mechanical properties and wear behaviors of PANOF plain weave fabrics were tested. The limiting oxygen index (LOI) of these PANOF plain weave fabric samples was 31%, which meets the criterion of flame-retardant fabrics. These fabrics neither melt nor shrunk when left in flame for a short period of time and the fabric structures were well maintained. Compared with flammable polyacrylonitrile fabrics, the polyacrylonitrile pre-oxidation fabrics exhibited excellent flame retardation properties, with satisfactory mechanical properties and comfortable handle.

Effect of ammonium polyphosphate and fillers on flame retardant and mechanical properties of recycled PET injection molded

2015 ◽  
Vol 28 (8) ◽  
pp. 979-985 ◽  
Author(s):  
Supaphorn Thumsorn ◽  
Takanori Negoro ◽  
Wiranphat Thodsaratpreeyakul ◽  
Hiroyuki Inoya ◽  
Masayuki Okoshi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flame Retardant ◽  
Ammonium Polyphosphate ◽  
Recycled Pet ◽  
Injection Molded

Flammability and mechanical properties of poly(styrene–butadiene–styrene) copolymer–containing intumescent flame retardants

2015 ◽  
Vol 30 (6) ◽  
pp. 816-826 ◽  
Author(s):  
Yiren Huang ◽  
Jianwei Yang ◽  
Zhengzhou Wang
Keyword(s):  
Mechanical Properties ◽  
Flame Retardant ◽  
Flame Retardants ◽  
Oxygen Index ◽  
Limiting Oxygen Index ◽  
Styrene Butadiene Styrene ◽  
Flame Retardant Properties ◽  
Intumescent Flame Retardants ◽  
Styrene Butadiene ◽  
Butadiene Styrene

Flame-retardant properties of ammonium polyphosphate (APP) and its two microcapsules, APP with a shell of melamine–formaldehyde (MF) resin (MFAPP) and APP with a shell of epoxy resin (EPAPP), were studied in styrene–butadiene–styrene (SBS). The results indicate that APP after the microencapsulation leads to an increase in limiting oxygen index in SBS compared with APP. When dipentaerythritol is incorporated into the SBS composites containing the APP microcapsules, a further improvement in flame retardancy of the composites is observed. The microencapsulation does not result in much improvement of mechanical properties. Moreover, the effect of a compatibilizer (SBS grafted with maleic anhydride) on flame-retardant and mechanical properties of SBS/APP composites was investigated.

scholarly journals Preparation and properties of flame-retardant epoxy resins containing reactive phosphorus flame retardant

2020 ◽  
Vol 15 ◽  
pp. 155892502090132
Author(s):  
Sang-Hoon Lee ◽  
Seung-Won Oh ◽  
Young-Hee Lee ◽  
Il-Jin Kim ◽  
Dong-Jin Lee ◽  
...  
Keyword(s):  
Impact Strength ◽  
Flame Retardant ◽  
Epoxy Resin ◽  
Flame Retardancy ◽  
Epoxy Resins ◽  
Phosphorus Content ◽  
Phosphorus Compound ◽  
Phosphorus Compounds ◽  
Limiting Oxygen Index ◽  
The Impact

To prepare flame-retardant epoxy resin, phosphorus compound containing di-hydroxyl group (10-(2,5-dihydroxyphenyl)-9,10-dihydro-9-oxa-10-phospha phenanthrene-10-oxide, DOPO-HQ) was reacted with uncured epoxy resin (diglycidyl ether of bisphenol A, YD-128) and then cured using a curing agent (dicyandiamide, DICY). This study focused on the effect of phosphorus compound/phosphorus content on physical properties and flame retardancy of cured epoxy resin. The thermal decomposition temperature of the cured epoxy resins (samples: P0, P1.5, P2.0, and P2.5, the number represents the wt% of phosphorus) increased with increasing the content of phosphorus compound/phosphorus (0/0, 19.8/1.5, 27.8/2.0, and 36.8/2.5 wt%) based on epoxy resin. The impact strength of the cured epoxy resin increased significantly with increasing phosphorus compound content. As the phosphorus compound/phosphorus content increased from 0/0 to 36.8/2.5 wt%, the glass transition temperature (the peak temperature of loss modulus curve) increased from 135.2°C to 142.0°C. In addition, as the content of phosphorous compound increased, the storage modulus remained almost constant up to higher temperature. The limiting oxygen index value of cured epoxy resin increased from 21.1% to 30.0% with increasing phosphorus compound/phosphorus content from 0/0 to 36.8/2.5 wt%. The UL 94 V test result showed that no rating for phosphorus compounds less than 19.8 wt% and V-1 for 27.8 wt%. However, when the phosphorus compound was 36.8 wt%, the V-0 level indicating complete flame retardancy was obtained. In conclusion, the incorporation of phosphorus compounds into the epoxy chain resulted in improved properties such as impact strength and heat resistance, as well as a significant increase in flame retardancy.

scholarly journals Development of Bioepoxy Resin Microencapsulated Ammonium-Polyphosphate for Flame Retardancy of Polylactic Acid

Molecules ◽  
2019 ◽  
Vol 24 (22) ◽  
pp. 4123 ◽  
Author(s):  
Kata Decsov ◽  
Katalin Bocz ◽  
Beáta Szolnoki ◽  
Serge Bourbigot ◽  
Gaëlle Fontaine ◽  
...  
Keyword(s):  
Ftir Spectroscopy ◽  
Flame Retardant ◽  
Polylactic Acid ◽  
Ammonium Polyphosphate ◽  
Cone Calorimetry ◽  
Scanning Calorimetry ◽  
Electron Microscopic ◽  
Sem Images ◽  
Limiting Oxygen Index ◽  
Microencapsulated Ammonium Polyphosphate

Ammonium-polyphosphate (APP) was modified by microencapsulation with a bio-based sorbitol polyglycidyl ether (SPE)-type epoxy resin and used as a flame retardant additive in polylactic acid (PLA) matrix. The bioresin-encapsulated APP (MCAPP) particles were characterized using Fourier transform infrared (FTIR) spectroscopy and Raman mapping, particle size distribution was determined by processing of scanning electron microscopic (SEM) images. Interaction between the APP core and the bioresin shell was revealed by combined thermogravimetric analysis (TGA)‑FTIR spectroscopy. The APP to SPE mass ratio of 10 to 2 was found to be optimal in terms of thermal, flammability, and mechanical properties of 15 wt% additive containing biocomposites. The bioresin shell effectively promotes the charring of the APP-loaded PLA composites, as found using TGA and cone calorimetry, and eliminates the flammable dripping of the specimens during the UL-94 vertical burning tests. Thus, the V-0 rating, the increased limiting oxygen index, and the 20% reduced peak of the heat release rate was reached compared to the effects of neat APP. Furthermore, better interfacial interaction of the MCAPP with PLA was indicated by differential scanning calorimetry and SEM observation. The stiff interphase resulted in increased modulus of these composites. Besides, microencapsulation provided improved water resistance to the flame retardant biopolymer system.

Sign in / Sign up

Export Citation Format

Share Document