scholarly journals Wire Ropes and CFRP Strips to Provide Masonry Walls with Out-Of-Plane Strengthening

Materials ◽  
2019 ◽  
Vol 12 (17) ◽  
pp. 2712
Author(s):  
Elena Ferretti
Keyword(s):  
Steel Wire ◽  
Three Dimensional ◽  
Maximum Load ◽  
Masonry Wall ◽  
Masonry Walls ◽  
Wire Ropes ◽  
Out Of Plane ◽  
Beam Mechanism ◽  
Combined Technique ◽  
The Ideal

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP (Carbon Fiber Reinforced Polymer) strips, to increase the out-of-plane ultimate load of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips on the two faces of the masonry wall gives rise to an I-beam behavior that forces the CFRP strips to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element a greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering action provided by the floors on the perimeter walls, during an earthquake. Lastly, when the building suffers heavy structural damage due to a strong earthquake, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

scholarly journals Wire Ropes and CFRP Strips to Provide the Masonry Walls with Out-of-Plane Strengthening

2019 ◽  
Author(s):  
Elena Ferretti
Keyword(s):  
Steel Wire ◽  
Three Dimensional ◽  
Maximum Load ◽  
Masonry Wall ◽  
Masonry Walls ◽  
Wire Ropes ◽  
Out Of Plane ◽  
Beam Mechanism ◽  
Combined Technique ◽  
The Ideal

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP strips, to increase the out-of-plane strength of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips placed on the two faces of the masonry wall gives rise to an I-beam behavior of the facing CFRP strips, which begin to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering actions provided by the floors on the perimeter walls, during an earthquake. Lastly, after the building went out of service, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

scholarly journals Wire Ropes and CFRP Strips to Provide the Masonry Walls with Out-of-Plane Strengthening

2019 ◽  
Author(s):  
Elena Ferretti
Keyword(s):  
Steel Wire ◽  
Three Dimensional ◽  
Maximum Load ◽  
Masonry Wall ◽  
Masonry Walls ◽  
Wire Ropes ◽  
Out Of Plane ◽  
Beam Mechanism ◽  
Combined Technique ◽  
The Ideal

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP strips, to increase the out-of-plane strength of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips placed on the two faces of the masonry wall gives rise to an I-beam behavior of the facing CFRP strips, which begin to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering actions provided by the floors on the perimeter walls, during an earthquake. Lastly, after the building went out of service, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

scholarly journals Combined Strengthening Techniques to Improve the Out-of-Plane Performance of Masonry Walls

2019 ◽  
Author(s):  
Elena Ferretti ◽  
Giovanni Pascale
Keyword(s):  
Flexural Strength ◽  
Three Dimensional ◽  
Experimental Results ◽  
Masonry Walls ◽  
Mechanical Coupling ◽  
Out Of Plane ◽  
Combined Technique ◽  
The Ideal

The purpose of this study is to improve the performance of walls under out-of-plane loads, particularly when subjected to the hammering action of the floors. The idea behind the paper is to provide the masonry walls with a device that behaves like a buttress, without having to build a traditional buttress. The solution presented here consists of a mechanical coupling between the three-dimensional net of steel ribbons of the CAM system and the CFRP strips. Since the steel ribbons of the CAM system have a pre-tension, the mechanical coupling allows the steel ribbons to establish a semi-rigid transverse link between the CFRP strips bonded on two opposite sides of a wall. Therefore, two vertical CFRP strips tied by the steel ribbons behave like the flanges of an I-beam and the flexural strength of the ideal I-beam counteracts the out-of-plane displacements of the wall. The experimental results showed that the combined technique inherits the strong points of both constituent techniques: the delamination load is comparable to that of the specimens reinforced with the CFRP strips and the overall behavior is ductile as for the specimens reinforced with the CAM system. They also allowed us to design a more performing combined technique.

scholarly journals Combined Strengthening Techniques to Improve the Out-of-Plane Performance of Masonry Walls

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1171 ◽  
Author(s):  
Elena Ferretti ◽  
Giovanni Pascale
Keyword(s):  
Three Dimensional ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Masonry Walls ◽  
Mechanical Coupling ◽  
Reinforced Polymer ◽  
Out Of Plane ◽  
Active Confinement ◽  
Combined Technique ◽  
The Ideal

The purpose of this study is to improve the performance of walls under out-of-plane loads especially when subjected to the hammering action of the floors. The idea behind the paper is to provide the masonry walls with a device that behaves like a buttress, without having to build a traditional buttress. The solution presented in this paper consists of a mechanical coupling between the three-dimensional net of steel ribbons of the CAM (Active Confinement of Masonry) system and the CFRP (Carbon Fiber Reinforced Polymer) strips. Since the steel ribbons of the CAM system have a pre-tension, the mechanical coupling allows the steel ribbons to establish a semi-rigid transverse link between the CFRP strips bonded on the two opposite sides of a wall. Therefore, two vertical CFRP strips tied by the steel ribbons behave like the flanges of an I-beam and the flexural strength of the ideal I-beam counteracts the out-of-plane displacements of the wall. The experimental results showed that the combined technique inherits the strong points of both constituent techniques. In fact, the delamination load is comparable to that of the specimens reinforced with the CFRP strips and the overall behavior is as ductile as for the specimens reinforced with the CAM system. They also inspired a more performing combined technique.

Mechanical Properties of Various Models of Interlocking Concrete Blocks under In-Plane and Out-of-Plane Loads

2021 ◽  
Vol 881 ◽  
pp. 149-156
Author(s):  
Mochamad Teguh ◽  
Novi Rahmayanti ◽  
Zakki Rizal
Keyword(s):  
Mechanical Properties ◽  
Building Material ◽  
Experimental Tests ◽  
Concrete Block ◽  
Masonry Wall ◽  
Masonry Walls ◽  
Plane Shear ◽  
Out Of Plane ◽  
Concrete Blocks ◽  
Local Materials

Building material innovations in various interlocking concrete block masonry from local materials to withstand lateral earthquake forces is an exciting issue in masonry wall research. The block hook has an advantage in the interlocking system's invention to withstand loads in the in-plane and out-of-plane orientations commonly required by the masonry walls against earthquake forces. Reviews of the investigation of in-plane and out-of-plane masonry walls have rarely been found in previous studies. In this paper, the results of a series of experimental tests with different interlocking models in resisting the simultaneous in-plane shear and out-of-plane bending actions on concrete blocks are presented. This paper presents a research investigation of various interlocking concrete blocks' mechanical properties with different hook thicknesses. Discussion of the trends mentioned above and their implications towards interlocking concrete block mechanical properties is provided.

Pre-Tensioned Basalt Fibers Ropes Stitching for Masonry Strengthening against Vertical Bending: A First Experimental Insight

2017 ◽  
Vol 747 ◽  
pp. 119-127 ◽  
Author(s):  
Francesco Monni ◽  
Enrico Quagliarini ◽  
Stefano Lenci
Keyword(s):  
Seismic Behavior ◽  
Basalt Fiber ◽  
Masonry Wall ◽  
Masonry Walls ◽  
Architectural Heritage ◽  
Experimental Campaign ◽  
Out Of Plane ◽  
Most Significant Change ◽  
Synthetic Adhesives ◽  
The Common

This paper presents the results of an experimental campaign aimed at improving the innovative technique of continuos basalt fiber (BF) stitching in order to repair the masonry panels damaged by seismic events or to enhance the seismic behavior of unreinforced masonry walls. The masonry panels were tested under out-of-plane actions, one of the common way of failure for masonry walls during an earthquake. The most significant change introduced respect to the system already tested in previous studies, is the presence of pre-tensioned elements and mechanical anchorage of the BF ropes, always with the end of proposing a dry retrofitting system. The results indicate the effectiveness of this, increasing the performance of masonry wall specimens under out-of-plane actions respect to the damaged and unreinforced conditions. Besides, this technique potentially appears fully sustainable, because it is cheap, compatible, reversible, fire, and chemical resistant, it improves but not replaces original materials and, finally, it does not substantially use synthetic adhesives. All these reasons make this novel application of BF ropes fully sustainable and specialized to architectural heritage restoration.

Behaviour of hollow concrete masonry walls with one-course bond beams subjected to concentric and eccentric concentrated loading

2003 ◽  
Vol 30 (1) ◽  
pp. 181-190 ◽  
Author(s):  
Junyi Yi ◽  
Nigel G Shrive
Keyword(s):  
Finite Element ◽  
Failure Modes ◽  
Three Dimensional ◽  
Masonry Walls ◽  
Finite Element Models ◽  
Concentrated Load ◽  
Concrete Masonry ◽  
Out Of Plane ◽  
Concentrated Loading ◽  
Concrete Masonry Walls

Three-dimensional finite element models of unreinforced hollow concrete masonry walls with one-course bond beams subjected to concentrated loading have been analyzed. The walls were modelled with different loading plate sizes, different loading locations along the wall (at the midpoint of the wall, at the end of the wall, and between these points), and different out-of-plane eccentricities (e = 0, t/6, and t/3). The hollow block units, mortar, grout, and bond beam blocks in the walls were modelled separately. Both smeared and discrete cracking methods have been utilized for predicting cracking under load. Geometric and material nonlinearities and damage due to progressive cracking were taken into account in the analyses. The predicted failure modes and ultimate capacities of the walls with the concentric concentrated load applied at the midpoint or at the end of the wall compared very well with the experimental results. When the load was between the midpoint and the end of the wall, the predicted ultimate capacity was between those for the load at the midpoint and at the end. The strength of the walls decreases with increasing out-of-plane eccentricities.Key words: finite element models, hollow masonry, smeared and discrete cracking models, concentrated load, loading locations, out-of-plane eccentricities.

MATERIAL AND OUT-OF-PLANE FLEXURAL PROPERTIES OF TRADITIONAL MASONRY WALL

2016 ◽  
Vol 3 (2) ◽  
Author(s):  
Noriko Takiyama ◽  
Akari Yamaguchi ◽  
Kohei Hara ◽  
Verdejo Juan Ramon Jimenez
Keyword(s):  
Mechanical Characteristics ◽  
Structural Characteristics ◽  
Tensile Tests ◽  
The Philippines ◽  
Masonry Wall ◽  
Flexural Properties ◽  
Masonry Walls ◽  
Out Of Plane ◽  
Material Tests ◽  
Compressive Tests

The October 2013 Earthquake hit the Bohol Island of the Philippines. Many traditional churches were damaged by the earthquake. In this study, material tests were conducted to assess the strength of the Philippines’ traditional masonry wall, which is composed of various materials. Additionally, out-of-plane flexural experiments were conducted to elucidate the mechanical characteristics of masonry walls found in traditional churches. The wall specimens used in this study were made of a variety of materials with different compositions. The major findings of this study are summarized as follows: (a) compressive tests and splitting tensile tests were conducted for various test samples having distinct compositions. For both tests, the strength of the cylinders without additional materials was greater than that with contamination, expect for those containing egg whites; (b) out-of-plane flexural experiments were conducted on four specimens to identify their structural characteristics.

Out-of-Plane Strengthening of Masonry Walls with FRCM Composite Materials

2017 ◽  
Vol 747 ◽  
pp. 158-165 ◽  
Author(s):  
Alessandro Bellini ◽  
Andrea Incerti ◽  
Claudio Mazzotti
Keyword(s):  
Composite Materials ◽  
Failure Modes ◽  
Theoretical Models ◽  
Masonry Wall ◽  
Image Correlation ◽  
Vertical Position ◽  
Masonry Walls ◽  
Out Of Plane ◽  
Set Up ◽  
Innovative Techniques

Structural strengthening by using composite materials proved to be one of the most suitable solutions for reinforcing masonry buildings. In this framework, the focus point of the presented experimental study is to evaluate the out-of-plane behaviour of masonry walls strengthened with Fiber Reinforced Cementitious Matrix (FRCM) composites when subjected to horizontal actions, by analyzing and discussing failure modes and their out-of-plane capacity. To this purpose, a new experimental set-up was developed, capable of applying an axial force and out-of-plane horizontal actions on full-scale masonry panels, placed in vertical position and subjected to a stress state similar to that present on a real masonry wall. Experimental results, obtained by using traditional and innovative techniques (such as Digital Image Correlation), will be compared with those coming from more conventional tensile and bond tests performed on FRCM coupons applied on masonry substrates, making use of simple theoretical models.

Sign in / Sign up

Export Citation Format

Share Document