scholarly journals Ni/cerium Molybdenum Oxide Hydrate Microflakes Composite Coatings Electrodeposited from Choline Chloride: Ethylene Glycol Deep Eutectic Solvent

Materials ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 924 ◽  
Author(s):  
Juliusz Winiarski ◽  
Anna Niciejewska ◽  
Jacek Ryl ◽  
Kazimierz Darowicki ◽  
Sylwia Baśladyńska ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Composite Coating ◽  
Molybdenum Oxide ◽  
Composite Coatings ◽  
Choline Chloride ◽  
Active Form ◽  
Deep Eutectic Solvent ◽  
Corrosion Process ◽  
Self Healing ◽  
Oxide Hydrate

Cerium molybdenum oxide hydrate microflakes are codeposited with nickel from a deep eutectic solvent-based bath. During seven days of exposure in 0.05 M NaCl solution, the corrosion resistance of composite coating (Ni/CeMoOxide) is slightly reduced, due to the existence of some microcracks caused by large microflakes. Multielemental analysis of the solution, in which coatings are exposed and the qualitative changes in the surface chemistry (XPS) show selective etching molybdenum from microflakes. The amount of various molybdenum species within the surface of coating nearly completely disappear, due to the corrosion process. Significant amounts of Ce3+ compounds are removed, however the corrosion process is less selective towards the cerium, and the overall cerium chemistry remains unchanged. Initially, blank Ni coatings are covered by NiO and Ni(OH)2 in an atomic ratio of 1:2. After exposure, the amount of Ni(OH)2 increases in relation to NiO (ratio 1:3). For the composite coating, the atomic ratios of both forms of nickel vary from 1:0.8 to 1:1.3. Despite achieving lower corrosion resistance of the composite coating, the applied concept of using micro-flakes, whose skeleton is a system of Ce(III) species and active form are molybdate ions, may be interesting for applications in materials with potential self-healing properties.

scholarly journals Zn-Co-CeO2 vs. Zn-Co Coatings: Effect of CeO2 Sol in the Enhancement of the Corrosion Performance of Electrodeposited Composite Coatings

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 704
Author(s):  
Marija Riđošić ◽  
Nebojša D. Nikolić ◽  
Asier Salicio-Paz ◽  
Eva García-Lecina ◽  
Ljiljana S. Živković ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Healing Rate ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Self Healing ◽  
Kelvin Probe ◽  
Artificial Defect ◽  
Volta Potential ◽  
Superior Corrosion Resistance ◽  
The Stability

Electrodeposition and characterization of novel ceria-doped Zn-Co composite coatings was the main goal of this research. Electrodeposited composite coatings were compared to pure Zn-Co coatings obtained under the same conditions. The effect of two ceria sources, powder and home-made sol, on the morphology and corrosion resistance of the composite coatings was determined. During the electrodeposition process the plating solution was successfully agitated in an ultrasound bath. The source of the particles was found to influence the stability and dispersity of plating solutions. The application of ceria sol resulted in an increase of the ceria content in the resulting coating and favored the refinement from cauliflower-like morphology (Zn-Co) to uniform and compact coral-like structure (Zn-Co-CeO2 sol). The corrosion resistance of the composite coatings was enhanced compared to bare Zn-Co as evidenced by electrochemical impedance spectroscopy and scanning Kelvin probe results. Zn-Co doped with ceria particles originating from ceria sol exhibited superior corrosion resistance compared to Zn-Co-CeO2 (powder) coatings. The self-healing rate of artificial defect was calculated based on measured Volta potential difference for which Zn-Co-CeO2 (sol) coatings exhibited a self-healing rate of 73.28% in a chloride-rich environment.

Experimental investigation of electrodeposited Ni-Al2O3/ZrO2 nano composite on HSLA ASTM A860 alloy

2021 ◽  
Author(s):  
Chandrasekhara Sastry Chebiyyam ◽  
Pradeep N ◽  
Shaik AM ◽  
Hafeezur Rahman A ◽  
Sandeep Patil
Keyword(s):  
Grain Size ◽  
Corrosion Resistance ◽  
Composite Coating ◽  
Base Alloy ◽  
Composite Coatings ◽  
Nano Particles ◽  
Alloy Sample ◽  
Nano Composite ◽  
Nano Coating ◽  
Nano Composite Coating

Abstract Nano composite coatings on HSLA ASTM A860 alloy, adds to the barrier efficacy by increase in the microhardness, wear and corrosion resistance of the substrate material. Additionally, reduction of delamination of the nano composite coating sample is ascertained. Ball milling is availed to curtail the coating samples (Al2O3/ZrO2) to nano size, for forming a electrodeposited product on the substrate layer. The curtailment in grain size was ascertained to be 17.62% in Ni-Al2O3/ZrO2 nano composite coating. During the deposition process, due to the presence of Al2O3/ZrO2 nano particles an increase in cathode efficiency is ascertained. An XRD analysis of the nano composite coating indicates a curtailment in grain size along with increase in the nucleation sites causing a surge in the growth of nano coating layer. In correlation to uncoated HSLA ASTM A36 alloy sample, a surge in compressive residual stress by 47.14%, reduction of waviness by 32.14% (AFM analysis), upsurge in microhardness by 67.77% is ascertained in Ni-Al2O3/ZrO2 nano composite coating. Furthermore, in nano coated Ni-Al2O3/ZrO2 composite a reduction is observed pertaining to weight loss and friction coefficients by 27.44% and 13% in correlation to plain uncoated alloy respectively. A morphology analysis after nano coating indicates, Ni-Al2O3/ZrO2 particles occupy the areas of micro holes, reducing the wide gaps and crevice points inside the matrix of the substrate, enacting as a physical barrier to upsurge the corrosion resistance by 67.72% in correlation to HSLA ASTM A860 base alloy.

scholarly journals Cellulose microfibers (CMFs) reinforced smart self-healing polymeric composite coatings for corrosion protection of steel

2020 ◽  
Author(s):  
Muddasir Nawaz ◽  
Sehrish Habib ◽  
Adnan Khan ◽  
Abdul Shakoor ◽  
Ramazan Kahraman
Keyword(s):  
Corrosion Resistance ◽  
Immersion Time ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Polymeric Composite ◽  
Protective Film ◽  
Self Healing ◽  
Ph Change ◽  
Smart Coatings ◽  
Cellulose Microfibers

The use of organic coating for the metals has been widely being used to protect the surface against corrosion. Polymeric coating incorporated with Nanocontainers loaded with inhibitor and self-healing provides better corrosion resistance. Cellulose microfibers (CMFs) used as smart carriers were synthesized and loaded with dodecylamine (DOC)-inhibitor and polyethyleneimine (PEI)-both inhibitor and self-healing agents. Smart polymeric coatings were developed by mixing CMF/DOC and CMFs/PEI into the epoxy matrix. Reference coatings (that has only CMFs) were also prepared for a compersion. Scanning electron microscope (SEM), X-ray diffraction spectroscopy (XRD), Fourier transform infrared spectroscopy (FTIR) and thermal gravitational analysis (TGA) were used to confirm the loading of DOC and PEI onto the CMFs. UV-vis analysis indicates that the self-release of inhibitor from CMFs is sensitive to pH of the solution and the immersion time. Recovery of controlled surface damage confirms the decent self-healing ability of the prepared smart coatings is due to the efficient release of inhibitor (DOC) and self-healing agent (PEI) in the damaged area leading to the formation of a protective film. Electrochemical impedance spectroscopy (EIS) results demonstrate that corrosion resistance of the smart coating increases with an increase in immersion time which is due to the progressive release of inhibitors from CMFs in response to the pH change. Therefore, smart coatings demonstrate superior properties as compared to the reference coatings. The study reveals the polymeric composite coatings have potential to inhibit the corrosion of steel for oil and gas industry.

scholarly journals Microstructure, friction and corrosion resistance properties of a Ni–Co–Al2O3 composite coating

RSC Advances ◽  
2018 ◽  
Vol 8 (22) ◽  
pp. 12138-12145 ◽  
Author(s):  
Zong-wei Jia ◽  
Wan-chang Sun ◽  
Fang Guo ◽  
Ya-ru Dong ◽  
Xiao-jia Liu
Keyword(s):  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Composite Coating ◽  
Composite Coatings ◽  
Al2o3 Composite ◽  
Pulsed Electrodeposition

Ni–Co–Al2O3 composite coatings were prepared by pulsed electrodeposition and electrophoresis–electrodeposition on aluminum alloy.

scholarly journals Composite Coatings of Chromium and Nanodiamond Particles on Steel

2017 ◽  
Vol 62 (4) ◽  
pp. 2421-2424 ◽  
Author(s):  
N. Gidikova ◽  
M. Sulowski ◽  
V. Petkov ◽  
R. Valov ◽  
G. Cempura
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Composite Coating ◽  
Composite Coatings ◽  
Machine Building ◽  
Chromium Coating ◽  
Detonation Synthesis ◽  
Micro Structure ◽  
X Ray ◽  
Average Size

AbstractChrome plating is used to improve the properties of metal surfaces like hardness, corrosion resistance and wear resistance in machine building. To further improve these properties, an electrodeposited chromium coating on steel, modified with nanodiamond particles is proposed. The nanodiamond particles (average size 4 nm measured by TEM) are produced by detonation synthesis (NDDS). The composite coating (Cr+NDDS) has an increased thickness, about two times greater microhardness and finer micro-structure compared to that of unmodified chromium coating obtained under the same galvanization conditions. In the microstructure of specimen obtained from chrome electrolyte with concentration of NDDS 25 g/l or more, “minisections” with chromium shell were found. They were identified by metallographic microscope and X-ray analyser on etched section of chromium plated sample. The object of further research is the dependence of the presence of NDDS in the composite coating from the nanodiamond particles concentration in the chroming electrolyte.

Preparation and Property of Electrodeposited Zn-Fe-SiO2 Composite Coating

2008 ◽  
Vol 373-374 ◽  
pp. 212-215 ◽  
Author(s):  
Yun Ying Fan ◽  
Ying Jie Zhang ◽  
Peng Dong
Keyword(s):  
Corrosion Resistance ◽  
Hydrogen Embrittlement ◽  
Surface Morphology ◽  
Composite Coating ◽  
Hydrogen Content ◽  
Particle Concentration ◽  
Composite Coatings ◽  
Particle Content ◽  
Sulfate Bath ◽  
Sio2 Particles

Electrodeposited Zn and Zn-Fe alloy have been applied widely to protect steel from corrosion, but the property of coating still needs to be improved. In this paper, Zn-Fe-SiO2 composite coatings are electrodeposited from Zn-Fe alloy electrolyte containing SiO2 particles. Zinc based coatings with Fe% >1%(mass) are deposited from sulfate bath, and coatings with Fe% <1%(mass) are deposited from chloride bath. Particle content in the composite coating generally increases with particle concentration under an adequate agitation and then tends to saturation. The optimum particle content in the composite coating is 0.5%(mass). Corrosion resistance, porosity, hydrogen embrittlement and surface morphology of Zn-Fe-SiO2 composite coatings have been tested and compared with electrodeposited Zn and Zn-Fe alloy. The data implies that Zn-Fe-SiO2 composite coating has the best corrosion resistance, lowest porosity, lowest hydrogen content and the finest crystal. All the results show that Zn-Fe-SiO2 composite coating is satisfactory to be used as anti-corrosion material for steel and has a great future in application.

Preparation and characterization of superhydrophobic composite coatings on a magnesium–lithium alloy

RSC Advances ◽  
2016 ◽  
Vol 6 (93) ◽  
pp. 90587-90596 ◽  
Author(s):  
Zhijun Li ◽  
Yi Yuan
Keyword(s):  
Corrosion Resistance ◽  
Composite Coating ◽  
Composite Coatings ◽  
Alloy Surface ◽  
Water Repellent ◽  
Lithium Alloy

We report a superhydrophobic organophosphonate composite coating on a magnesium–lithium alloy surface, which exhibits excellent water-repellent and corrosion resistance properties.

scholarly journals Graphene-Based Coating for Corrosion Application

2019 ◽  
Vol 8 (6S4) ◽  
pp. 378-380
Keyword(s):  
Corrosion Resistance ◽  
Composite Coating ◽  
Molybdenum Oxide ◽  
Chemical Resistance ◽  
Salt Spray ◽  
Immersion Test ◽  
High Mechanical Strength ◽  
Electro Deposition ◽  
Reduced Graphene ◽  
One Step

Graphene-based, molybdenum oxide-based and composite coating were prepared by one-step electro-deposition without using aggressive solutions. The coatings were characterised by Scanning Electron Microscope (SEM). The corrosion resistance of the three coatings were evaluated by immersion test (ASTM G31-72), salt spray test (ASTM B117-16) and potentiodynamicpolarisation, in 5% NaCl and 2% H2SO4 respectively. All of the results indicated that reduced graphene oxide – molybdenum oxide (rGO/MoO) composite coating exhibits the highest corrosion resistance in both saline and acidic environment. This could be ascribed to the synergistic effect of both graphene and molybdenum oxide with the combination of high mechanical strength and superior chemical resistance.

Microstructure and corrosion resistance of Ni/Cr3C2-NiCr composite coating

2019 ◽  
Vol 66 (4) ◽  
pp. 471-478 ◽  
Author(s):  
Majid Hosseinzadeh ◽  
Abdol Hamid Jafari ◽  
Rouhollah Mousavi ◽  
Mojtaba Esmailzadeh
Keyword(s):  
Corrosion Resistance ◽  
Composite Coating ◽  
Design Methodology ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Thermal Spraying ◽  
Content Type ◽  
Bath Solution ◽  
Electrochemical Deposition Method ◽  
Base Composite

Purpose In this study, electrochemical deposition method which have cheaper equipment than thermal spraying methods and is available for the production of composite coatings were used. Design/methodology/approach Composite coatings were electrodeposited from a Watts's bath solution in which the suspended Cr3C2-NiCr particles were dispersed in the bath solution during deposition. Potentiodynamic polarization and electrochemical impedance spectroscopy techniques have been used to evaluate the corrosion resistance of the composite coating in the 3.5 Wt.% NaCl solution. Findings It was found that the submicron Cr3C2-NiCr particles distributed uniformly in the coating and depend on the current density of deposition, different amount of particles can be incorporated in the coating. The results showed that the corrosion resistance of the Ni/ Cr3C2-NiCr composite coatings is more comparable to the pure nickel coating. Originality/value Production of Ni-base composite coating from an electrolytic bath containing Cr3C2-NiCr particles is possible via electrodeposition.

Sign in / Sign up

Export Citation Format

Share Document