scholarly journals Correlation of Strain Path, Texture, Twinning, and Mechanical Properties in Twinning-Induced Plasticity Steel during Wire Drawing

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2250 ◽  
Author(s):  
Joong-Ki Hwang
Keyword(s):  
Mechanical Properties ◽  
Strain Path ◽  
Electron Backscatter Diffraction ◽  
Steel Wire ◽  
Effective Strain ◽  
Metal Flow ◽  
Wire Drawing ◽  
Surface Areas ◽  
The Wire ◽  
Backscatter Diffraction

The effect of changing the strain path on texture development, twin kinetics, and mechanical properties in twinning-induced plasticity steel was investigated to understand twinning behavior in more detail. Among the various plastic deformation processes, the wire drawing process was selected to achieve the aims of the study. Specimens of cold-drawn TWIP steel wire under the same effective strain but with different crystallographic textures were successfully fabricated using the effect of the wire drawing direction. Electron backscatter diffraction results showed that the drawn wires using both unidirectional (UD) and reverse-directional (RD) wire drawing processes were characterized as duplex fiber textures of major <111> and minor <100>. It was found that the RD wire had a higher fraction of <111> component at both the center and surface areas compared to the UD wire, because the metal flow of the RD wire was beneficial for the development of a <111> orientation. The pronounced <111> crystallographic orientation of the RD wire activated the twinning rate and geometrically necessary dislocation density, leading to an increase in strength but a decrease in ductility. The strain path is as important as the amount of strain for strengthening the materials, especially those that are deformed by twinning.

scholarly journals Microstructural Evolutions and Mechanical Properties of Drawn Medium Carbon Steel Wire

2019 ◽  
Vol 41 ◽  
pp. 1-7 ◽  
Author(s):  
Mohamed Chaouki Nebbar ◽  
Mosbah Zidani ◽  
Toufik Djimaoui ◽  
T. Abid ◽  
Hichem Farh ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Steel ◽  
Electron Backscatter Diffraction ◽  
Texture Evolution ◽  
Steel Wire ◽  
Wire Drawing ◽  
Medium Carbon Steel ◽  
X Ray Diffraction ◽  
Medium Carbon ◽  
Backscatter Diffraction

This study focuses on the evolution in the microstructure, texture and mechanical properties of medium carbon steel wires obtained by wire drawing at Tréfissoud Company for the manufacturing of the spring mattress. Wire drawing induces elongation of grains in the direction of drawing with the development of the <110> fibre texture parallel to the wire axis. Kinking and bending of cementite lamellae were observed during the drawing process. The work was carried out respectively on three states, wire rod and drawn states for two different amounts (ε %=43,6 and 60 %), using the optical and SEM microscopy, electron backscatter diffraction and X-ray diffraction analysis for examination of the microstructure and texture evolution, the hardness Vickers and tensile test to follow the curing of the studied wires.

Deformation Law of Cold Drawing Process of High Strength Bridge Cable Steel

2021 ◽  
Vol 1035 ◽  
pp. 801-807
Author(s):  
Xiao Lei Yin ◽  
Jian Cheng ◽  
Gang Zhao
Keyword(s):  
Strain Path ◽  
High Strength ◽  
Cold Drawing ◽  
Wire Drawing ◽  
Radial Deformation ◽  
Steel Bridge ◽  
Drawing Process ◽  
Single Pass ◽  
Potential Relationship ◽  
The Wire

High-strength cable-steel bridge is the “lifeline” of steel structure bridges, which requires high comprehensive mechanical properties, and cold-drawing is the most important process to produce high-strength cable-steel bridge. Therefore, through the ABAQUS platform, a bridge wire drawing model was established, and the simulation analysis on the process of stress strain law and strain path trends for high-strength bridge steel wire from Φ 12.65 mm by seven cold-drawing to Φ 6.90 mm was conducted. The simulation results show that the wire drawing the heart of the main axial deformation, surface and sub-surface of the main axial and radial deformation occurred, with the increase in the number of drawing the road, the overall deformation of the wire was also more obvious non-uniformity. In the single-pass drawing process, the change in the potential relationship of each layer of material was small, and multiple inflection points appeared in the strain path diagram; the change in the seven-pass potential relationship was more drastic, which can basically be regarded as a simple superposition of multiple single-pass pulls.

Use of Electron Backscatter Diffraction Technique in Characterization of 6XXX Aluminum Alloy Extrusions

2000 ◽  
Vol 6 (S2) ◽  
pp. 954-955
Author(s):  
Steven R. Claves ◽  
Wojciech Z. Misiolek ◽  
William H. Van Geertruyden ◽  
David B. Williams
Keyword(s):  
Electron Backscatter Diffraction ◽  
Metal Flow ◽  
Extrusion Process ◽  
Cross Sectional ◽  
Electron Backscattering Diffraction ◽  
Electron Backscatter ◽  
Individual Grains ◽  
Backscatter Diffraction ◽  
6Xxx Series

Electron Backscattering Diffraction (EBSD) is an important tool for analyzing the crystal grain orientation of a microstructure and can be used to formulate conclusions about microtexture, texture determined from individual grains. This technique has been used to study a 6xxx series aluminum alloy's response to the deformation of the extrusion process. Extrusion is the process by which a billet of material is forced, under high pressure, through a die. The material undergoes a significant decrease in cross sectional area, and is formed into a shape equivalent to the geometry of the die orifice. Different bearing lands are shown in shown in Figure 1. These surfaces form the part, and are designed to control the metal flow making it uniform through the die, thus yielding good mechanical properties. This research was focused on the resultant microstructure. The shaded regions of Figure 2 show the two surface regions where EBSD measurements were taken.

Microstructure and Mechanical Properties of Ti Cold-Spray Splats Determined by Electron Channeling Contrast Imaging and Nanoindentation Mapping

2015 ◽  
Vol 21 (3) ◽  
pp. 570-581 ◽  
Author(s):  
Dina Goldbaum ◽  
Richard R. Chromik ◽  
Nicolas Brodusch ◽  
Raynald Gauvin
Keyword(s):  
Mechanical Properties ◽  
Cold Spray ◽  
Electron Backscatter Diffraction ◽  
Substrate Material ◽  
Contrast Imaging ◽  
Electron Channeling ◽  
Metallurgical Bonding ◽  
Resolution Electron ◽  
Backscatter Diffraction ◽  
The Impact

AbstractCold spray is a thermo-mechanical process where the velocity of the sprayed particles affects the deformation, bonding, and mechanical properties of the deposited material, in the form of splats or coatings. At high strain rates, the impact stresses are converted into heat, a phenomenon known as adiabatic shear, which leads to grain re-crystallization. Grain re-crystallization and growth are shown to have a direct impact on the mechanical properties of the cold-sprayed material. The present study ties the microstructural features within the cold-sprayed Ti splats and the substrate to the bonding mechanism and mechanical properties. High-resolution electron channeling contrast imaging, electron backscatter diffraction mapping, and nanoindentation were used to correlate the microstructure to the mechanical properties distribution within the titanium cold-spray splats. The formation of nanograins was observed at the titanium splat/substrate interface and contributed to metallurgical bonding. An increase in grain re-crystallization within the splat and substrate materials was observed with pre-heating of the substrate. In the substrate material, the predominant mechanism of deformation was twinning. A good relationship was found between the hardness and distribution of the twins within the substrate and the size distribution of the re-crystallized grains within the splats.

scholarly journals Research on the Microstructures and Mechanical Properties of Bainite/Martensite Rail Treated by the Controlled-Cooling Process

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3061 ◽  
Author(s):  
Jiajia Qiu ◽  
Min Zhang ◽  
Zhunli Tan ◽  
Guhui Gao ◽  
Bingzhe Bai
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Toughness ◽  
Electron Backscatter Diffraction ◽  
Microstructural Characterization ◽  
Cooling Process ◽  
Controlled Cooling ◽  
Transmission Electron ◽  
Backscatter Diffraction

A bainite/martensite multiphase rail is treated by the controlled-cooling process with different finish-cooling temperatures. The simulated temperature–time curves of the position of 5 mm and 15 mm below the rail tread (P5 and P15) express different trends. P5 has greater impact toughness and lower tensile strength than P15. Microstructural characterization was carried out by conducting scanning electron microscopy, X-ray diffraction, electron backscatter diffraction, and transmission electron microscopy. The greater tensile strength is due to the dispersed ε-carbides hindering the movement of dislocations. The greater impact toughness is attributed to the filmy retained austenite and the smaller effective grain with high-angle boundary. Finite element modeling (FEM) and microstructural characterization reasonably explain the changes of mechanical properties. The present work provides experimental and theoretical guidance for the development of rail with excellent mechanical properties.

A Plasto-Hydrodynamic Analysis of the Lubrication and Coating of Wire Using a Polymer Melt during Drawing

1977 ◽  
Vol 191 (1) ◽  
pp. 115-123 ◽  
Author(s):  
P.J. Thompson ◽  
G.R. Symmons
Keyword(s):  
Steel Wire ◽  
Polymer Melt ◽  
Wire Drawing ◽  
Operating Conditions ◽  
Hydrodynamic Analysis ◽  
The Wire

A study is undertaken of the lubrication of steel wire drawing using a Christopherson tube and a polymer melt as a lubricant. Primary objectives of the study are to determine the criteria under which a thin, well adhered coat of the polymer is deposited on the wire after drawing. An analysis determines these criteria and enables the polymer coat thickness to be obtained for given operating conditions. Several flow defects are observed and discussed.

Development of Asymmetric Rolling for the Better Control over Structure and Mechanical Properties in IF Steel

2012 ◽  
Vol 706-709 ◽  
pp. 2788-2793 ◽  
Author(s):  
Dmitry Orlov ◽  
Rimma Lapovok ◽  
László S. Tóth ◽  
Ilana B. Timokhina ◽  
Peter D. Hodgson ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Electron Backscatter Diffraction ◽  
Tensile Tests ◽  
Experimental Investigations ◽  
If Steel ◽  
Asymmetric Rolling ◽  
Electron Backscatter ◽  
Strain Components ◽  
Backscatter Diffraction ◽  
Crystallographic Orientations

In the present study, the effects of kinematic and geometric asymmetries in rolling during multi-pass processing of IF steel are examined. The theoretical investigation by final element simulations and experimental investigations by means of electron-backscatter diffraction analysis and tensile tests suggest that asymmetric rolling increases the total imposed strain compared to symmetric rolling, and largely re-distributes the strain components due to additional shear. This enhances the intensity of grain refinement, strengthens and tilts crystallographic orientations, and increases mechanical strength. The effect is highest in the asymmetric rolling with differential roll diameters.

Influence of Strain Path Changes on Microstructure Inhomogeneity and Mechanical Behavior of Wire Drawing Products

2010 ◽  
Vol 654-656 ◽  
pp. 314-317 ◽  
Author(s):  
K. Muszka ◽  
M. Wielgus ◽  
J. Majta ◽  
K. Doniec ◽  
Monika Stefanska-Kadziela
Keyword(s):  
Mechanical Properties ◽  
Strain Path ◽  
Low Carbon Steel ◽  
Wire Drawing ◽  
Drawing Process ◽  
Low Carbon ◽  
Forming Process ◽  
Steel Wires ◽  
Diameter Reduction ◽  
Strength And Ductility

Cold drawn low carbon steel wires are widely used in several engineering applications where a proper combination of strength and ductility is of the paramount importance. In the present paper, the multi-pass angular accumulative drawing (AAD) is proposed as a new forming process where the high strain accumulation is used as a way to achieve much higher microstructure refinement level compared to the conventional wire drawing process. This process is characterized by a complex strain path history, being an effect of wire diameter reduction, bending, tension and torsion, what directly affects the microstructure changes in the final product. This process also evolves high inhomogeneity of microstructure, that if properly controlled, can lead to further properties improvement - what can be especially beneficial for alloys that are not characterized by complex compositions. In the present paper, special emphasis is given on the inhomogeneity of both deformation and microstructure and resulted mechanical properties. After drawing and annealing (at 500oC) mechanical properties measurements and microstructure analysis on the longitudinal sections of the wires were performed to assess the differences existing with respect to the conventional wire drawing process.

scholarly journals Selected Problems of the Microstructure Evolution During Microalloyed Steel Wire Rod Production Process

2017 ◽  
Vol 62 (2) ◽  
pp. 899-904 ◽  
Author(s):  
M. Kwiecień ◽  
P. Graca ◽  
K. Muszka ◽  
J. Majta
Keyword(s):  
Mechanical Properties ◽  
Grain Refinement ◽  
Thermomechanical Processing ◽  
Microalloyed Steel ◽  
Steel Wire ◽  
Wire Drawing ◽  
Point Of View ◽  
Microalloyed Steels ◽  
Combined Processes ◽  
Microstructure Development

Abstract In the present study, we have discussed the selected problems of microstructure development during the whole manufacturing process, i.e. continuous casting, thermomechanical processing, and cold metal forming of the microalloyed steels wires. In the investigated steels, the microstructure development was controlled by the history of deformation and by the effects of microalloying elements, mostly Nb, Ti, and B. It has been concluded that obtained in the ultrafine grained microalloyed steel wires mechanical properties were first of all resulting from specific structural composition and grain refinement. Additionally, it has been proven that austenite grain refinement, that increases nucleation rate during the austenite-to-ferrite phase transformation, as a result of the thermomechanical processing, are very beneficial from point of view of the final mechanical properties. This problem starts to be very important when the microalloyed steel products are subjected to severe plastic deformation, as it has been shown discussed in the present work for combined processes of wire drawing and wire flattening.

Sign in / Sign up

Export Citation Format

Share Document