scholarly journals Comparison of Hook and Straight Steel Fibers Addition on Malaysian Fly Ash-Based Geopolymer Concrete on the Slump, Density, Water Absorption and Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1310
Author(s):  
Meor Ahmad Faris ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Ratnasamy Muniandy ◽  
Mohammad Firdaus Abu Hashim ◽  
Katarzyna Błoch ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Flexural Strength ◽  
Physical Properties ◽  
Water Absorption ◽  
Steel Fiber ◽  
Carbon Dioxide Emission ◽  
Steel Fibers ◽  
Geopolymer Concrete ◽  
Volume Percentage

Geopolymer concrete has the potential to replace ordinary Portland cement which can reduce carbon dioxide emission to the environment. The addition of different amounts of steel fibers, as well as different types of end-shape fibers, could alter the performance of geopolymer concrete. The source of aluminosilicate (fly ash) used in the production of geopolymer concrete may lead to a different result. This study focuses on the comparison between Malaysian fly ash geopolymer concrete with the addition of hooked steel fibers and geopolymer concrete with the addition of straight-end steel fibers to the physical and mechanical properties. Malaysian fly ash was first characterized by X-ray fluorescence (XRF) to identify the chemical composition. The sample of steel fiber reinforced geopolymer concrete was produced by mixing fly ash, alkali activators, aggregates, and specific amounts of hook or straight steel fibers. The steel fibers addition for both types of fibers are 0%, 0.5%, 1.0%, 1.5%, and 2.0% by volume percentage. The samples were cured at room temperature. The physical properties (slump, density, and water absorption) of reinforced geopolymer concrete were studied. Meanwhile, a mechanical performance which is compressive, as well as the flexural strength was studied. The results show that the pattern in physical properties of geopolymer concrete for both types of fibers addition is almost similar where the slump is decreased with density and water absorption is increased with the increasing amount of fibers addition. However, the addition of hook steel fiber to the geopolymer concrete produced a lower slump than the addition of straight steel fibers. Meanwhile, the addition of hook steel fiber to the geopolymer concrete shows a higher density and water absorption compared to the sample with the addition of straight steel fibers. However, the difference is not significant. Besides, samples with the addition of hook steel fibers give better performance for compressive and flexural strength compared to the samples with the addition of straight steel fibers where the highest is at 1.0% of fibers addition.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

scholarly journals Developing Geopolymer Concrete Properties by Using Nanomaterials and Steel Fibers

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
E. Rabiaa ◽  
R. A. S. Mohamed ◽  
W. H. Sofi ◽  
Taher A. Tawfik
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Sodium Hydroxide ◽  
Steel Fiber ◽  
Splitting Tensile Strength ◽  
Steel Fibers ◽  
Hardened Concrete ◽  
Geopolymer Concrete ◽  
Alkaline Activator ◽  
The Impact

This research investigates the simultaneous impact of two different types of steel fibers, nanometakaolin, and nanosilica on the mechanical properties of geopolymer concrete (GPC) mixes. To achieve this aim, different geopolymer concrete mixes were prepared. Firstly, with and without nanomaterials (nanosilica and nanometakaolin) of 0, 2%, 4%, 6%, and 8% from ground granulated blast furnace slag (GGBFS) were used. Secondly, steel fiber (hooked end and crimped) content of (0, 0.5%, 1, and 1.5%) was used. Thirdly, optimum values of nanomaterials with the optimum values of steel fiber were used. Crimped and hooked-end steel fibers were utilized with an aspect ratio of 60 and a length of 30 mm. Geopolymer mixes were manufactured by using a constant percentage of alkaline activator to binder proportion equal to 0.45 with GGBFS cured at ambient conditions. For alkaline activator, sodium hydroxide molar (NaOH) and sodium hydroxide solution (NaOH) were used according to a proportion (Na2SiO3/NaOH) of 2.33. The hardened concrete tests were performed through the usage of splitting tensile strength, flexural, and compressive experiments to determine the impact of steel fibers, nanometakaolin, and nanosilica individually and combined on performance of GPC specimens. The results illustrated that using a mix composed of the optimum steel fibers (1% content) accompanied by an optimum percentage of 6% nanometakaolin or 4% nanosilica demonstrated a significant enhancement in the mechanical properties of GPC specimens compared to all other mixtures. Besides, the impact of using nanomaterials individually was found to be predominant on compressive strength on GPC specimens especially with the usage of the optimum values. However, using nanomaterials individually compared to using the steel fibers individually was found to have approximately the same splitting tensile strength and flexural performance.

Properties of Steel Fiber Reinforced Geopolymer

2015 ◽  
Vol 659 ◽  
pp. 143-148 ◽  
Author(s):  
Rachamongkon Wongruk ◽  
Smith Songpiriyakij ◽  
Piti Sukontasukkul ◽  
Prinya Chindaprasirt
Keyword(s):  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
Steel Fibre ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Fibre Volume Fraction ◽  
Fibre Volume ◽  
Steel Fibers ◽  
Flexural Performance

In this study, the mechanical properties of steel fibre reinforced geopolymer (SFRG) are investigated. The geopolymer is consisted of fly ash, silica fume and activator solution, sodium silicate and sodium hydroxide. Five mix proportions of fly ash and silica fume are varied to study the effect of fly ash/silica fume ratios (FA/SF). This experimental series focus mainly on flexural strength and flexural toughness performance of SFRG. Hooked-ends steel fibers are used at 0.5% and 1% by volume fractions. The experiment is carried out based on ASTM C1609 (beam specimens) for flexural performance. The results showed that fibre can significantly enhance the both flexural strength and toughness of geopolymer. The enhancement also increases with the increasing fibre volume fraction.

scholarly journals Effect of fly ash on physical and mechanical properties of mortar

2019 ◽  
Vol 17 (6) ◽  
pp. 35
Author(s):  
Vu-An Tran
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Water Absorption ◽  
Thermal Power ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Flow Density ◽  
Control Specimen

This research investigates the physical and mechanical properties of mortar incorporating fly ash (FA), which is by-product of Duyen Hai thermal power plant. Six mixtures of mortar are produced with FA at level of 0%, 10%, 20%, 30%, 40%, and 50% (by volume) as cement replacement and at water-to-binder (W/B) of 0.5. The flow, density, compressive strength, flexural strength, and water absorption tests are made under relevant standard in this study. The results have shown that the higher FA content increases the flow of mortar but significantly decreases the density of mixtures. The water absorption and setting time increases as the samples incorporating FA. Compressive strength of specimen with 10% FA is approximately equal to control specimen at the 91-day age. The flexural strength of specimen ranges from 7.97 MPa to 8.94 MPa at the 91-day age with the best result for samples containing 10% and 20% FA.

scholarly journals Use of waste paper ash or wood ash as substitution to fly ash in production of geopolymer concrete

2021 ◽  
Vol 30 (3) ◽  
pp. 464-476
Author(s):  
Haider Owaid ◽  
Haider Al-Baghdadi ◽  
Muna Al-Rubaye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Sodium Hydroxide ◽  
Wood Ash ◽  
Splitting Tensile Strength ◽  
Waste Paper ◽  
Geopolymer Concrete

Large quantities of paper and wood waste are generated every day, the disposal of these waste products is a problem because it requires huge space for their disposal. The possibility of using these wastes can mitigate the environmental problems related to them. This study presents an investigation on the feasibility of inclusion of waste paper ash (WPA) or wood ash (WA) as replacement materials for fly ash (FA) class F in preparation geopolymer concrete (GC). The developed geopolymer concretes for this study were prepared at replacement ratios of FA by WPA or WA of 25, 50, 75 and 100% in addition to a control mix containing 100% of FA. Sodium hydroxide (NaOH) solutions and sodium silicate (Na2SiO3) are used as alkaline activators with 1M and 10M of sodium hydroxide solution.The geopolymer concretes have been evaluated with respect to the workability, the compressive strength, splitting tensile strength and flexural strength. The results indicated that there were no significant differences in the workability of the control GC mix and the developed GC mixes incorporating WPA or WA. Also, the results showed that, by incorporating of 25–50% PWA or 25% WA, the mechanical properties (compressive strength, splitting tensile strength and flexural strength) of GC mixes slightly decreased. While replacement with 75–100% WPA or with 50–100% WA has reduced these mechanical properties of GC mixes. As a result, there is a feasibility of partial replacement of FA by up to 50% WPA or 25% WA in preparation of the geopolymer concrete.

scholarly journals Mechanical and Microstructural Characterization of Quarry Rock Dust Incorporated Steel Fiber Reinforced Geopolymer Concrete and Residual Properties after Exposure to Elevated Temperatures

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6890
Author(s):  
Muhammad Ibraheem ◽  
Faheem Butt ◽  
Rana Muhammad Waqas ◽  
Khadim Hussain ◽  
Rana Faisal Tufail ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Weight Loss ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mechanical Strength ◽  
Elevated Temperatures ◽  
Strength Properties ◽  
Steel Fibers ◽  
Geopolymer Concrete

The purpose of this research is to study the effects of quarry rock dust (QRD) and steel fibers (SF) inclusion on the fresh, mechanical, and microstructural properties of fly ash (FA) and ground granulated blast furnace slag (SG)-based geopolymer concrete (GPC) exposed to elevated temperatures. Such types of ternary mixes were prepared by blending waste materials from different industries, including QRD, SG, and FA, with alkaline activator solutions. The multiphysical models show that the inclusion of steel fibers and binders can enhance the mechanical properties of GPC. In this study, a total of 18 different mix proportions were designed with different proportions of QRD (0%, 5%, 10%, 15%, and 20%) and steel fibers (0.75% and 1.5%). The slag was replaced by different proportions of QRD in fly ash, and SG-based GPC mixes to study the effect of QRD incorporation. The mechanical properties of specimens, i.e., compressive strength, splitting tensile strength, and flexural strength, were determined by testing cubes, cylinders, and prisms, respectively, at different ages (7, 28, and 56 days). The specimens were also heated up to 800 °C to evaluate the resistance of specimens to elevated temperature in terms of residual compressive strength and weight loss. The test results showed that the mechanical strength of GPC mixes (without steel fibers) increased by 6–11%, with an increase in QRD content up to 15% at the age of 28 days. In contrast, more than 15% of QRD contents resulted in decreasing the mechanical strength properties. Incorporating steel fibers in a fraction of 0.75% by volume increased the compressive, tensile, and flexural strength of GPC mixes by 15%, 23%, and 34%, respectively. However, further addition of steel fibers at 1.5% by volume lowered the mechanical strength properties. The optimal mixture of QRD incorporated FA-SG-based GPC (QFS-GPC) was observed with 15% QRD and 0.75% steel fibers contents considering the performance in workability and mechanical properties. The results also showed that under elevated temperatures up to 800 °C, the weight loss of QFS-GPC specimens persistently increased with a consistent decrease in the residual compressive strength for increasing QRD content and temperature. Furthermore, the microstructure characterization of QRD blended GPC mixes were also carried out by performing scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy dispersive spectroscopy (EDS).

Combined effect of nano-SiO2 particles and steel fibers on flexural properties of concrete composite containing fly ash

2014 ◽  
Vol 21 (4) ◽  
pp. 597-605 ◽  
Author(s):  
Peng Zhang ◽  
Ya-nan Zhao ◽  
Chen-hui Liu ◽  
Peng Wang ◽  
Tian-hang Zhang
Keyword(s):  
Fly Ash ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Steel Fiber ◽  
Flexural Modulus ◽  
Fiber Content ◽  
Steel Fibers ◽  
Combined Effect ◽  
Nano Particles ◽  
Flexural Properties

AbstractThis paper presents an experimental study to evaluate the combined effect of nano-SiO2 particles and steel fibers on flexural properties of concrete composites containing fly ash. In this study, five different nano-SiO2 contents (1%, 3%, 5%, 7%, and 9%) and five different steel fiber contents (0.5%, 1%, 1.5%, 2%, and 2.5%) were used. The results indicate that addition of nano-SiO2 and steel fibers decreases the workability of the concrete composites containing fly ash, and both the slump and slump flow decrease gradually with the increase in nano-SiO2 and steel fiber content. Besides, the addition of nano-SiO2 can greatly increase the flexural strength and flexural modulus of elasticity of concrete composites containing fly ash. There is a tendency for the increase in the flexural strength flexural modulus of elasticity with an increase in the nano-SiO2 content when the nano-SiO2 content is below 5%, while both of the two flexural parameters begin to decrease after the nano-SiO2 content above 5%. Furthermore, steel fibers have great improvement on the flexural properties of concrete composites containing fly ash and nano-particles. The flexural strength and flexural modulus of elasticity of concrete composites containing fly ash and nano-SiO2 are more than those of the concrete composite without steel fibers. Both of the two flexural parameters increase with the increase in steel fiber content when the steel fiber content is below 2%, while the flexural parameters begin to decrease after the steel fiber content is above 2%.

Experimental Study on Mechanical Properties of Steel Fiber Reinforced High Performance Concrete

2013 ◽  
Vol 859 ◽  
pp. 56-59 ◽  
Author(s):  
Yong Qiang Ma
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
High Performance ◽  
Steel Fiber ◽  
High Performance Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced

A large number of experiments have been carried out in this study to reveal the effect of the steel fiber dosage on the mechanical properties of HPC (high performance concrete). The mechanical property includes compressive strength, elastic modulus and flexural strength. The results indicate that the addition of steel fiber increase the compressive strength, elastic modulus and flexural strength of HPC. When the steel fiber dosage is less than 2%, these mechanical property parameters are increasing gradually with the increase of steel fiber dosage, while these parameters begin to decrease when the steel fiber dosage is more than 2%. With the development of HPC, the application of steel fibers in HPC becomes more and more popular. In the actual construction of steel fiber reinforced HPC, the dosage of steel fiber should be controlled strictly in order to ensure that the steel fibers can perform their best improvement on high performance concrete.

scholarly journals STUDY ON MECHANICAL PROPERTIES OF HIGH STRENGTH CONCRETE WITH SILICA FUME, FLYASH AND STEEL FIBER

2021 ◽  
Vol 6 (1) ◽  
Author(s):  
Atul Ranjan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fly Ash ◽  
Construction Industry ◽  
Silica Fume ◽  
Steel Fiber ◽  
High Strength ◽  
Steel Fibers ◽  
Split Tensile Strength ◽  
To Come

In this growing world there has always been a strong competition in the market amongst industries in term of economy, profits, shares etc. one such industry is construction industry where concrete is the key building substance which is in limelight. Since past, we have seen much advancement in concrete because of the research which is in progress on concrete to come out with a product which should be economical and strong enough to resist all kind of loads. In this thesis, fly ash and silica fume are used as a replacement for cement along with steel fibers by volume of concrete. Here, fly ash is replaced by 0%, 15%, 30% and silica fume is replaced by 0%, 6%, 12% and 18% for cement. Initially, a set of concrete specimens were casted with 0%, 15%, 30% fly ash and 0%, 6%, 12% and 18% silica fume with 0% addition of steel fibers and tested for compressive, flexural and split tensile strength. Secondly, another set of concrete specimens were casted with 0%, 15%, 30% fly ash and 0%, 6%, 12% and 18% silica fume with 0.5% addition of steel fibers and tested for the same. Similarly, another set of samples were casted 0%, 15%, 30% fly ash and 0%, 6%, 12% and 18% silica fume with 1% addition of steel fibers and tested to determine the mechanical properties of concrete. And it was observed that maximum compressive, flexural and split tensile strength was attained at 15% fly ash and 12% silica fume with 1% steel fiber

Sign in / Sign up

Export Citation Format

Share Document