scholarly journals Characteristics of Impulse Carburization LPC Process

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4269
Author(s):  
Ryszard Filip ◽  
Kamil Ochał ◽  
Kamil Gancarczyk ◽  
Wojciech Jerzy Nowak ◽  
Barbara Kościelniak ◽  
...  
Keyword(s):  
Residual Stresses ◽  
Carbon Content ◽  
Martensite Transformation ◽  
Thermochemical Treatment ◽  
Residual Austenite ◽  
Local Extremum ◽  
Depth Range ◽  
Compressive Stresses ◽  
Different Depths ◽  
Carburized Layer

In the present work, Pyrowear53 steel was subjected to the impulse carburizing LPC process. After carburation, the material was quenched and tempered. Postprocessing analyses included the measurement of hardness, carbon content, residual austenite, and residual stresses. The results revealed that the thermochemical treatment resulted in the formation of an approximately 1200 µm wide carburized layer. The results of hardness, carbon content, and residual austenite measurement showed a continuous gradient (drop) in the measured values within the carburized layer. However, the results of residual stresses revealed the existence of a local extremum, namely, a zone with higher compressive stresses at the depth between 600 and 1000 µm. This was explained by a different temperature for initiation of martensite transformation as a function of carbon content. This difference resulted in the occurrence of two martensite expansion fronts at two different depths, resulting in an increase in compressive stresses at the noted depth range. Moreover, it was concluded that this region was present for material containing between 0.8 and 0.4 wt% carbon for Pyrowear53.

Theoretical study of the prestressing strand's stress by computer modeling methods

2020 ◽  
Vol 76 (11) ◽  
pp. 1139-1148
Author(s):  
A. G. Korchunov ◽  
E. M. Medvedeva ◽  
E. M. Golubchik
Keyword(s):  
Residual Stresses ◽  
High Strength ◽  
Pearlitic Steel ◽  
Internal Stresses ◽  
Steel Microstructure ◽  
Compressive Stresses ◽  
Wide Range ◽  
Prestressing Strands ◽  
Increasing Temperature ◽  
Wire Strand

The modern construction industry widely uses reinforced concrete structures, where high-strength prestressing strands are used. Key parameters determining strength and relaxation resistance are a steel microstructure and internal stresses. The aim of the work was a computer research of a stage-by-stage formation of internal stresses during production of prestressing strands of structure 1х7(1+6), 12.5 mm diameter, 1770 MPa strength grade, made of pearlitic steel, as well as study of various modes of mechanical and thermal treatment (MTT) influence on their distribution. To study the effect of every strand manufacturing operation on internal stresses of its wires, the authors developed three models: stranding and reducing a 7-wire strand; straightening of a laid strand, stranding and MTT of a 7-wire strand. It was shown that absolute values of residual stresses and their distribution in a wire used for strands of a specified structure significantly influence performance properties of strands. The use of MTT makes it possible to control in a wide range a redistribution of residual stresses in steel resulting from drawing and strand laying processes. It was established that during drawing of up to 80% degree, compressive stresses of 1100-1200 MPa degree are generated in the central layers of wire. The residual stresses on the wire surface accounted for 450-500 MPa and were tension in nature. The tension within a range of 70 kN to 82 kN combined with a temperature range of 360-380°С contributes to a two-fold decrease in residual stresses both in the central and surface layers of wire. When increasing temperature up to 400°С and maintaining the tension, it is possible to achieve maximum balance of residual stresses. Stranding stresses, whose high values entail failure of lay length and geometry of the studied strand may be fully eliminated only at tension of 82 kN and temperature of 400°С. Otherwise, stranding stresses result in opening of strands.

scholarly journals Thermal Effects on Surface and Subsurface Modifications in Laser-Combined Deep Rolling

2021 ◽  
Vol 5 (2) ◽  
pp. 55
Author(s):  
Robert Zmich ◽  
Daniel Meyer
Keyword(s):  
Surface Layer ◽  
Residual Stresses ◽  
Thermal Loads ◽  
Deep Rolling ◽  
Mechanical Loads ◽  
Thermomechanical Process ◽  
Compressive Stresses ◽  
New Process ◽  
Negative Effect ◽  
Compressive Residual Stresses

Knowledge of the relationships between thermomechanical process loads and the resulting modifications in the surface layer enables targeted adjustments of the required surface integrity independent of the manufacturing process. In various processes with thermomechanical impact, thermal and mechanical loads act simultaneously and affect each other. Thus, the effects on the modifications are interdependent. To gain a better understanding of the interactions of the two loads, it is necessary to vary thermal and mechanical loads independently. A new process of laser-combined deep rolling can fulfil exactly this requirement. The presented findings demonstrate that thermal loads can support the generation of residual compressive stresses to a certain extent. If the thermal loads are increased further, this has a negative effect on the surface layer and the residual stresses are shifted in the direction of tension. The results show the optimum range of thermal loads to further increase the compressive residual stresses in the surface layer and allow to gain a better understanding of the interactions between thermal and mechanical loads.

scholarly journals Effect of Al2O3 Sandblasting Particle Size on the Surface Topography and Residual Compressive Stresses of Three Different Dental Zirconia Grades

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 610
Author(s):  
Hee-Kyung Kim ◽  
Byungmin Ahn
Keyword(s):  
Particle Size ◽  
Residual Stresses ◽  
Surface Topography ◽  
Tetragonal Zirconia ◽  
Peak Shift ◽  
Confocal Laser ◽  
Compressive Stresses ◽  
Surface Topographies ◽  
Altered Surface ◽  
Tetragonal Zirconia Polycrystal

This study investigated the effect of sandblasting particle size on the surface topography and compressive stresses of conventional zirconia (3 mol% yttria-stabilized tetragonal zirconia polycrystal; 3Y-TZP) and two highly translucent zirconia (4 or 5 mol% partially stabilized zirconia; 4Y-PSZ or 5Y-PSZ). Plate-shaped zirconia specimens (14.0 × 14.0 × 1.0 mm3, n = 60 for each grade) were sandblasted using different Al2O3 sizes (25, 50, 90, 110, and 125 μm) under 0.2 MPa for 10 s/cm2 at a 10 mm distance and a 90° angle. The surface topography was characterized using a 3-D confocal laser microscopy and inspected with a scanning electron microscope. To assess residual stresses, the tetragonal peak shift at 147 cm−1 was traced using micro-Raman spectroscopy. Al2O3 sandblasting altered surface topographies (p < 0.05), although highly translucent zirconia showed more pronounced changes compared to conventional zirconia. 5Y-PSZ abraded with 110 μm sand showed the highest Sa value (0.76 ± 0.12 μm). Larger particle induced more compressive stresses for 3Y-TZP (p < 0.05), while only 25 μm sand induced residual stresses for 5Y-PSZ. Al2O3 sandblasting with 110 μm sand for 3Y-TZP, 90 μm sand for 4Y-PSZ, and 25 μm sand for 5Y-PSZ were considered as the recommended blasting conditions.

Fracture of Layered Ceramics

2009 ◽  
Vol 409 ◽  
pp. 94-106 ◽  
Author(s):  
Raúl Bermejo ◽  
Luca Ceseracciu ◽  
Luis Llanes ◽  
Marc Anglada
Keyword(s):  
Residual Stresses ◽  
Thermal Strain ◽  
Ceramic Materials ◽  
Layered Structures ◽  
Internal Layers ◽  
Multilayered Structures ◽  
Compressive Stresses ◽  
Layered Ceramics ◽  
Different Response ◽  
Experimental Findings

Layered ceramics are foreseen as possible substitutes for monolithic ceramics due to their attractive mechanical properties in terms of strength reliability and toughness. The different loading conditions to which ceramic materials may be subjected in service encourage the design of tailored layered structures as function of their application. The use of residual stresses generated during cooling due to the different thermal strain of adjacent layers has been the keystone for the improvement of the fracture response of many layered ceramic systems, e.g. alumina-zirconia, alumina-mullite, silicon nitride-titanium nitride, etc. In this work, the fracture features of layered ceramics are addressed analysing two multilayered structures, based on the alumina-zirconia system, designed with tailored compressive residual stresses either in the external or internal layers. Contact strength and indentation strength tests have been performed to investigate the response of both designs to crack propagation. The experimental findings show a different response in terms of strength and crack growth resistance of both designs. While layered structures with compressive stresses at the surface provide a better response against contact damage compared to monoliths, a flaw tolerant design in terms of strength and an improved toughness through energy release mechanisms is achieved with internal compressive stresses. The use of layered architectures for automotive or biomedical applications as substitutes for alumina-based ceramics should be regarded in the near future, where reliable ceramic designs are needed.

Correlation of Residual Stresses in the Fatigue Strength of Axles

1942 ◽  
Vol 9 (2) ◽  
pp. A85-A90
Author(s):  
O. J. Horger ◽  
H. R. Neifert
Keyword(s):  
Heat Treatment ◽  
Fatigue Strength ◽  
Residual Stresses ◽  
High Surface ◽  
Full Size ◽  
Tensile Stresses ◽  
Compressive Stresses ◽  
Actual Service

Abstract The object of this paper is to present a correlation between residual stresses, obtained by heat-treatment, with fatigue values, determined from an investigation of full-size railroad axles. The axles tested were of both solid and tubular design and represent members which could be used under a car in actual service. It was found from these tests that high axle fatigue strength is associated with high surface residual compressive stresses, and lowest axle strength values with surface residual tensile stresses.

Simplified FEA Models in the Analysis of the Redistribution of Beneficial Compressive Stresses in Welds During Cyclic Loading

2018 ◽  
Author(s):  
B. L. Josefson ◽  
J. Alm ◽  
J. M. J. McDill
Keyword(s):  
Cyclic Loading ◽  
Residual Stresses ◽  
Compressive Stress ◽  
Welding Process ◽  
Plastic Behavior ◽  
Element Analysis ◽  
Compressive Stresses ◽  
Static Contact ◽  
Weld Toe ◽  
Compressive Residual Stresses

The fatigue life of welded joints can be improved by modifying the weld toe geometry or by inducing beneficial compressive residual stresses in the weld. However, in the second case, the induced compressive residual stresses may relax when the welded joint is subjected to cyclic loading containing high tensile or compressive stress peaks. The stability of induced compressive stresses is investigated for a longitudinal gusset made of a S355 steel. Two methods are considered; either carrying out a high frequency mechanical impact (HFMI) treatment after welding or alternatively using low transformation temperature (LTT) electrodes during welding. The specimen is then subjected to a cyclic loading case with one cycle with a tensile peak (with magnitude reaching the local yield stress level) followed by cycles with constant amplitude. A sequential finite element analysis (FEA) is performed thereby preserving the history of the elasto-plastic behavior. Both the welding process and the HFMI treatment are simulated using simplified approaches, i.e., the welding process is simulated by applying a simplified thermal cycle while the HFMI treatment is simulated by a quasi-static contact analysis. It is shown that using the simplified approaches to modelling both the welding process and HFMI treatment gives results that correlate qualitatively well with the experimental and FEA data available in the literature. Thus, for comparison purposes, simplified models may be sufficient. Both the use of the HFMI treatment and LTT electrodes give approximately the same compressive stress at the weld toe but the extent of the compressive stress zone is deeper for HFMI case. During cyclic loading it is shown that the beneficial effect of both methods will be substantially reduced if the test specimen is subjected to unexpected peak loads. For the chosen load sequence, with the same maximum local stress at the weld toe, the differences in stress curves of the HFMI-treated specimen and that with LTT electrodes remain. While the LTT electrode gives the lowest (compressive) stress right at the well toe, it is shown that the overall effect of the HFMI treatment is more beneficial.

Nanohardness of DC Magnetron Sputtered W – C Coatings as a Function of Composition and Residual Stresses

2015 ◽  
Vol 662 ◽  
pp. 107-110 ◽  
Author(s):  
Michal Novák ◽  
František Lofaj ◽  
Petra Hviščová ◽  
Rudolf Podoba ◽  
Marián Haršáni ◽  
...  
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Magnetron Sputtering ◽  
Linear Increase ◽  
Indentation Modulus ◽  
Dc Magnetron Sputtering ◽  
Glass Substrates ◽  
Compressive Stresses ◽  
Deposition Parameters

The effects of residual stresses in thin W-C based coatings were investigated with the aim to find their influence on nanohardness and indentation modulus. Ten samples of W-C based coatings were deposited on microslide glass substrates using DC magnetron sputtering at the identical deposition parameters. Their thickness was in the range from 500 to 600 nm. The residual stresses in the coatings varied from 1.5 GPa up to 4.4 GPa. Increase of residual stress caused linear increase of HITfrom 16 to 19.5 GPa. This increase was only the result of the compressive stresses. EITof the studied coatings was not sensitive to residual stresses and corresponded to 185 GPa ± 15 GPa.

scholarly journals ANALYSIS OF ACOUSTIC ANISOTROPY PARAMETERS OF PYROXENE-MAGNETITE ROCKS OF THE PISCHANKA STRUCTURE

2020 ◽  
pp. 40-45
Author(s):  
I. Bezrodna ◽  
V. Svystov ◽  
D. Bezrodny
Keyword(s):  
Acoustic Properties ◽  
Significant Heterogeneity ◽  
Depth Range ◽  
Transverse Waves ◽  
Acoustic Anisotropy ◽  
Micro Cracks ◽  
Acoustic Tensor ◽  
Transverse Isotropic ◽  
Different Depths ◽  
The Difference

The analysis of the results of acoustic properties of rocks study of Pischans`ka iron-ore structure is presented. The aim of the work is to establish the features of the distribution of acoustic properties and parameters of acoustic anisotropy in samples of core rocks selected from the well No. 3 of the Pischans`ka structure to determine the nature of its occurrence. A sample of 35 samples from the depth range 144-273 m is divided into 3 groups of rocks, namely: magnetite-pyroxene, quartz-magnetitepyroxene and biotite-amphibole crystalline shales. Based on an invariant polarization method, a number of acoustic laboratory measurements have been carried out. The values of the measured phase velocities "quasi-longitudinal" and two "quasi-transverse" waves at the stage of measurements showed significant acoustic anisotropy of the rocks. The ranges of the measured speeds of the collection samples are 7661 ÷ 5046 m / s for longitudinal waves and 4232 ÷ 2648 m/s for transverse ones. The difference in values measured for each of the sides of the cubic rhombic dodecahedron is from 100 to 800 m / s and from 0 to 500 m/s for Vp and Vs, respectively. The parameters of an acoustic ellipsoid were calculated, on the basis of which the division of samples into 3 main groups has been performed, according to the acoustic texture: acoustically linear, shale and rhombic. Separately, a group of samples with a more complex texture was discovered. The analysis of coefficients of anisotropy by different methods is carried out: longitudinal, transverse and relative acoustic anisotropy. Most of the samples are characterized by low or average acoustic anisotropy (from 2 to 7 %). A group of highly anisotropic rocks (11–14 %), represented by samples of biotite-amphibole crystalline silicates, is singled out. According to the parameters of the acoustic tensor of most samples, the transverse isotropic type of symmetry inherent to samples from the depth intervals 174–220 m and 222–232 m, while the smaller part is rhombic, is inherent. Differences in the parameters of anisotropy of samples can be explained by the significant heterogeneity of their textures, namely: micro cracks, minerals of various sizes, shapes and orientations. The results of the research show that the acoustic properties of the samples are quite heterogeneously distributed along the investigated depth range. This indicates the difficult conditions for the formation of rocks at different depths and the presence of different types of deformations, which accompanied the formation of the Pischans`ka structure.

scholarly journals Formation of Residual Stresses during Discontinuous Friction Treatment

2021 ◽  
Vol 8 (1) ◽  
pp. C38-C44
Author(s):  
I. Hurey ◽  
V. Gurey ◽  
M. Bartoszuk ◽  
T. Hurey
Keyword(s):  
Grain Size ◽  
Residual Stresses ◽  
Mineral Oil ◽  
Surface Shape ◽  
Technological Medium ◽  
Flat Surfaces ◽  
Compressive Stresses ◽  
Friction Treatment ◽  
Working Surface ◽  
Pass Through

The tool with grooves on its working surface is used to improve the properties of the strengthened layer. This allows us to reduce the structure’s grain size and increase the thickness of the layer and its hardness. Mineral oil and mineral oil with active additives containing polymers are used as a technological medium during friction treatment. It is shown that the technological medium used during the friction treatment affects the nature of the residual stresses’ distribution. Thus, when using mineral oil with active additives containing polymers, residual compressive stresses are more significant in magnitude and depth than when treating mineral oil. The nature of the residual stresses diagram depends on the treated surface’ shape. After friction treatment of cylindrical surfaces, the highest compressive stresses near the treated surface decreases with depth. And after friction treatment of flat surfaces near the treated surface, the compressive stresses are small. They increase with depth, pass through the maximum, and then decrease to the original values. The technological medium used during friction treatment affects residual stresses in the grains and in the crystal lattice.

Sign in / Sign up

Export Citation Format

Share Document