scholarly journals Residual Strength and Drying Behavior of Concrete Reinforced with Recycled Steel Fiber from Tires

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6111
Author(s):  
David Revuelta ◽  
Pedro Carballosa ◽  
José Luis García Calvo ◽  
Filipe Pedrosa
Keyword(s):  
Residual Strength ◽  
Microstructural Analysis ◽  
Drying Shrinkage ◽  
Recycling Process ◽  
Geometrical Characterization ◽  
The Matrix ◽  
Drying Behavior ◽  
Size Variability ◽  
Recycled Steel

Fiber reinforcement of concrete is an effective technique of providing ductility to concrete, increasing its flexural residual strength while reducing its potential for cracking due to drying shrinkage. There are currently a wide variety of industrial fibers on the market. Recycled steel fibers (RSF) from tires could offer a viable substitute of industrialized fibers in a more sustainable and eco-friendly way. However, mistrust exists among users, based on fear that the recycling process will reduce the performance, coupled with the difficulty of characterization of the geometry of the RSF, as a consequence of the size variability introduced by the recycling process. This work compares the behavior of RSF from tires compared with industrialized steel or polypropylene fibers, evaluating the fresh state, compressive strength, flexural residual strength, and drying behavior. The concept of Equivalent Fiber Length (EFL) is also defined to help the statistical geometrical characterization of the RSF. A microstructural analysis was carried out to evaluate the integration of the fiber in the matrix, as well as the possible presence of contaminants. The conclusion is reached that the addition of RSF has a similar effect to that of industrialized fibers on concrete’s properties when added at the same percentage.

Effect of Parawood Ash on Drying Shrinkage, Compressive Strength and Microstructural Characterization of Metakaolin-Based Geopolymer Mortar

2013 ◽  
Vol 594-595 ◽  
pp. 411-415 ◽  
Author(s):  
Danupon Tonnayopas ◽  
Abideng Hawa ◽  
Woraphot Prachasaree ◽  
Pichai Taneerananon
Keyword(s):  
Compressive Strength ◽  
Microstructural Analysis ◽  
Drying Shrinkage ◽  
Microstructural Characterization ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
Microscopy Techniques ◽  
Metakaolin Geopolymer ◽  
Test Result

Drying shrinkage, compressive strength and microstructural analysis of metakaolin based geopolymers partial replacement with Parawood ash was investigated. It was involved different SiO2/Al2O3 and CaO/SiO2 ratios. Characterization of geopolymer mortar was determined on drying shrinkage, compressive strength, mineral phases and microstructure was analysed by X-ray diffraction and scanning electron microscopy techniques. Test result of highest compressive strength was about 71 MPa at 6-h (4-h in oven at 80oC and 2-h ambient temperature). Voids-cement ratio is the most effect on the unconfined compressive strength of this metakaolin geopolymer mortar.

TEM characterization of reaction zone in a SiC fiber-reinforced titanium alloy

1988 ◽  
Vol 46 ◽  
pp. 738-739
Author(s):  
G. Das ◽  
R. E. Omlor
Keyword(s):  
Titanium Alloys ◽  
Reaction Zone ◽  
Carbon Layer ◽  
Fiber Reinforced ◽  
Reaction Products ◽  
Sic Fibers ◽  
Sic Fiber ◽  
The Matrix ◽  
Immense Potential

Fiber reinforced titanium alloys hold immense potential for applications in the aerospace industry. However, chemical reaction between the fibers and the titanium alloys at fabrication temperatures leads to the formation of brittle reaction products which limits their development. In the present study, coated SiC fibers have been used to evaluate the effects of surface coating on the reaction zone in the SiC/IMI829 system.IMI829 (Ti-5.5A1-3.5Sn-3.0Zr-0.3Mo-1Nb-0.3Si), a near alpha alloy, in the form of PREP powder (-35 mesh), was used a茸 the matrix. CVD grown AVCO SCS-6 SiC fibers were used as discontinuous reinforcements. These fibers of 142μm diameter contained an overlayer with high Si/C ratio on top of an amorphous carbon layer, the thickness of the coating being ∽ 1μm. SCS-6 fibers, broken into ∽ 2mm lengths, were mixed with IMI829 powder (representing < 0.1vol%) and the mixture was consolidated by HIP'ing at 871°C/0. 28GPa/4h.

Applications of ultramicrotomy for materials characterization

1993 ◽  
Vol 51 ◽  
pp. 232-233
Author(s):  
R.T. Blackham ◽  
J.J. Haugh ◽  
C.W. Hughes ◽  
M.G. Burke
Keyword(s):  
Materials Science ◽  
Microstructural Analysis ◽  
Analytical Electron Microscopy ◽  
Austenitic Stainless Steels ◽  
Specimen Preparation ◽  
Preparation Technique ◽  
Thermally Induced ◽  
Radiation Induced ◽  
Characterization Of Materials

Essential to the characterization of materials using analytical electron microscopy (AEM) techniques is the specimen itself. Without suitable samples, detailed microstructural analysis is not possible. Ultramicrotomy, or diamond knife sectioning, is a well-known mechanical specimen preparation technique which has been gaining attention in the materials science area. Malis and co-workers and Glanvill have demonstrated the usefulness and applicability of this technique to the study of a wide variety of materials including Al alloys, composites, and semiconductors. Ultramicrotomed specimens have uniform thickness with relatively large electron-transparent areas which are suitable for AEM anaysis.Interface Analysis in Type 316 Austenitic Stainless Steel: STEM-EDS microanalysis of grain boundaries in austenitic stainless steels provides important information concerning the development of Cr-depleted zones which accompany M23C6 precipitation, and documentation of radiation induced segregation (RIS). Conventional methods of TEM sample preparation are suitable for the evaluation of thermally induced segregation, but neutron irradiated samples present a variety of problems in both the preparation and in the AEM analysis, in addition to the handling hazard.

GEOMETRICAL CHARACTERIZATION OF KELVIN-LIKE METAL FOAMS FOR DIFFERENT STRUT SHAPES AND POROSITY

2015 ◽  
Vol 18 (6) ◽  
pp. 637-652 ◽  
Author(s):  
Prashant Kumar ◽  
Frederic Topin ◽  
Lounes Tadrist
Keyword(s):  
Metal Foams ◽  
Geometrical Characterization

scholarly journals Waste-Based One-Part Alkali Activated Materials

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2911
Author(s):  
Margarida Gonçalves ◽  
Inês Silveirinha Vilarinho ◽  
Marinélia Capela ◽  
Ana Caetano ◽  
Rui Miguel Novais ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Microstructural Analysis ◽  
Construction Materials ◽  
Sodium Metasilicate ◽  
High Compressive Strength ◽  
Hardened State ◽  
First Time ◽  
Furnace Slag ◽  
Alkali Activated

Ordinary Portland Cement is the most widely used binder in the construction sector; however, a very high carbon footprint is associated with its production process. Consequently, more sustainable alternative construction materials are being investigated, namely, one-part alkali activated materials (AAMs). In this work, waste-based one-part AAMs binders were developed using only a blast furnace slag, as the solid precursor, and sodium metasilicate, as the solid activator. For the first time, mortars in which the commercial sand was replaced by two exhausted sands from biomass boilers (CA and CT) were developed. Firstly, the characterization of the slag and sands (aggregates) was performed. After, the AAMs fresh and hardened state properties were evaluated, being the characterization complemented by FTIR and microstructural analysis. The binder and the mortars prepared with commercial sand presented high compressive strength values after 28 days of curing-56 MPa and 79 MPa, respectively. The mortars developed with exhausted sands exhibit outstanding compressive strength values, 86 and 70 MPa for CT and CA, respectively, and the other material’s properties were not affected. Consequently, this work proved that high compressive strength waste-based one-part AAMs mortars can be produced and that it is feasible to use another waste as aggregate in the mortar’s formulations: the exhausted sands from biomass boilers.

scholarly journals Characterization of the Structure, Mechanical Properties and Erosive Resistance of the Laser Cladded Inconel 625-Based Coatings Reinforced by TiC Particles

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2225
Author(s):  
Aleksandra Kotarska ◽  
Tomasz Poloczek ◽  
Damian Janicki
Keyword(s):  
Laser Cladding ◽  
Inconel 625 ◽  
Matrix Composites ◽  
Erosion Rates ◽  
Laser Cladding Process ◽  
Composition Variation ◽  
The Matrix ◽  
Reinforcing Material ◽  
Inconel 625 Superalloy

The article presents research in the field of laser cladding of metal-matrix composite (MMC) coatings. Nickel-based superalloys show attractive properties including high tensile strength, fatigue resistance, high-temperature corrosion resistance and toughness, which makes them widely used in the industry. Due to the insufficient wear resistance of nickel-based superalloys, many scientists are investigating the possibility of producing nickel-based superalloys matrix composites. For this study, the powder mixtures of Inconel 625 superalloy with 10, 20 and 40 vol.% of TiC particles were used to produce MMC coatings by laser cladding. The titanium carbides were chosen as reinforcing material due to high thermal stability and hardness. The multi-run coatings were tested using penetrant testing, macroscopic and microscopic observations, microhardness measurements and solid particle erosive test according to ASTM G76-04 standard. The TiC particles partially dissolved in the structure during the laser cladding process, which resulted in titanium and carbon enrichment of the matrix and the occurrence of precipitates formation in the structure. The process parameters and coatings chemical composition variation had an influence on coatings average hardness and erosion rates.

Mechanical characterization of LM25 alloy matrix composite reinforced with boron carbide

2021 ◽  
pp. 002199832110055
Author(s):  
Zeeshan Ahmad ◽  
Sabah Khan
Keyword(s):  
Tensile Strength ◽  
Boron Carbide ◽  
Mechanical Characterization ◽  
Stir Casting ◽  
Surface Mapping ◽  
Alloy Matrix ◽  
Casting Technique ◽  
The Matrix ◽  
Carbide Particles

Alumnium alloy LM 25 based composites reinforced with boron carbide at different weight fractions of 4%, 8%, and 12% were fabricated by stir casting technique. The microstructures and morphology of the fabricated composites were studied by scanning electron microscopy and energy dispersive spectroscopy. Elemental mapping of all fabricated composites were done to demonstrate the elements present in the matrix and fabricated composites. The results of microstructural analyses reveal homogenous dispersion of reinforcement particles in the matrix with some little amount of clustering found in composites reinforced with 12% wt. of boron carbide. The mechanical characterization is done for both alloy LM 25 and all fabricated composites based on hardness and tensile strength. The hardness increased from 13.6% to 21.31% and tensile strength 6.4% to 22.8% as reinforcement percentage of boron carbide particles increased from 0% to 12% wt. A fractured surface mapping was also done for all composites.

scholarly journals Reliability Assessment of a Multi-State HVDC System by Combining Markov and Matrix-Based Methods

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3097
Author(s):  
Roberto Benato ◽  
Antonio Chiarelli ◽  
Sebastian Dambone Sessa
Keyword(s):  
Current System ◽  
Estimation Method ◽  
Reliability Estimation ◽  
Voltage Source ◽  
Voltage Source Converter ◽  
Hvdc System ◽  
Critical Elements ◽  
The Matrix ◽  
The Impact

The purpose of this paper is to highlight that, in order to assess the availability of different HVDC cable transmission systems, a more detailed characterization of the cable management significantly affects the availability estimation since the cable represents one of the most critical elements of such systems. The analyzed case study consists of a multi-terminal direct current system based on both line commutated converter and voltage source converter technologies in different configurations, whose availability is computed for different transmitted power capacities. For these analyses, the matrix-based reliability estimation method is exploited together with the Monte Carlo approach and the Markov state space one. This paper shows how reliability analysis requires a deep knowledge of the real installation conditions. The impact of these conditions on the reliability evaluation and the involved benefits are also presented.

A new approach to the bienergy and biangle of a moving particle lying in a surface of lorentzian space

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Talat Körpınar ◽  
Yasin Ünlütürk
Keyword(s):  
Vector Fields ◽  
Elastic Surface ◽  
Geometrical Characterization ◽  
Lorentzian Space ◽  
New Approach ◽  
Darboux Vector ◽  
Moving Particle ◽  
The Relationship ◽  
Surface Curve

AbstractIn this research, we study bienergy and biangles of moving particles lying on the surface of Lorentzian 3-space by using their energy and angle values. We present the geometrical characterization of bienergy of the particle in Darboux vector fields depending on surface. We also give the relationship between bienergy of the surface curve and bienergy of the elastic surface curve. We conclude the paper by providing bienergy-curve graphics for different cases.

Sign in / Sign up

Export Citation Format

Share Document