High-Temperature Corrosion Performance of FeAl-Based Alloys Containing Carbon in Molten Salt

Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 2040
Author(s):  
Munish Kumar ◽  
Ravi Kant ◽  
Suresh Chand ◽  
Ujjwal Prakash ◽  
Shankar Sehgal ◽  
...  
Keyword(s):  
Corrosion Behavior ◽  
Molten Salts ◽  
Corrosion Performance ◽  
X Ray Diffraction ◽  
Corrosive Media ◽  
Al2o3 Layer ◽  
X Ray ◽  
Aggressive Environment ◽  
Arc Melting ◽  
Ti Addition

Corrosion behavior of FeAl-based alloys containing carbon produced through arc melting in argon atmosphere has been studied at 500 °C to 700 °C. The samples were tested in the aggressive environment of molten salts (80%V2O5/20%Na2SO4). The corrosion behavior was observed by weight change method and the layer products formed were examined by using X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). The different phase components were observed in the surface layer after the test in Fe-22Al alloy. A protective Al2O3 layer was confirmed for Fe-22Al alloy containing carbon only. However, an additional TiO layer was also observed in Fe-22Al alloy containing carbon with Ti addition. The microstructural and XRD examinations revealed that this additional TiO layer protects better against penetration of corrosive media. The corrosion resistance behavior of FeAl-based alloys were addressed on the basis of microstructural evidence.

Effect of Zn Content on Structure, Roughness and Corrosion Behavior of Zn-Ni Alloys

2019 ◽  
Vol 17 (17) ◽  
pp. 17-22
Author(s):  
Hayette Faid
Keyword(s):  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Stripping Voltammetry ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ni Alloys ◽  
Sulfate Bath ◽  
Zn Content ◽  
Polarization Test ◽  
Δ Phase

AbstractIn this work, Zn-Ni alloys have been deposited on steel from sulfate bath, by electrodeposition method. The effect of Zn content on deposits properties was studied by cyclic voltammetry (CV), chronoaperometry (CA), linear stripping voltammetry (ALSV) and diffraction (XRD) and scanning electronic microscopy (SEM). The corrosion behavior in 3.5 wt. NaCl solution was examined using anodic polarization test and electrochemical impedance spectroscopy. X-ray diffraction of show that Zn-Ni alloys structure is composed of δ phase and γ phase, which increase with the decrease of Zn content in deposits. Results show that deposits obtained from bath less Zn2+ concentration exhibited better corrosion resistance.

scholarly journals Study of Structural, Magnetic, and Mossbauer Properties of Dy2Fe16Ga1−xNbx (0.0 ≤ x ≤ 1.0) Prepared via Arc Melting Process

2021 ◽  
Vol 7 (3) ◽  
pp. 42
Author(s):  
Jiba N. Dahal ◽  
Kalangala Sikkanther Syed Ali ◽  
Sanjay R. Mishra
Keyword(s):  
Isomer Shift ◽  
Cell Volume ◽  
Intermetallic Compounds ◽  
Unit Cell Volume ◽  
Rietveld Analysis ◽  
Unit Cell ◽  
X Ray Diffraction ◽  
X Ray ◽  
Arc Melting ◽  
Nb Content

Intermetallic compounds of Dy2Fe16Ga1−xNbx (x = 0.0 to 1.00) were synthesized by arc melting. Samples were investigated for structural, magnetic, and hyperfine properties using X-ray diffraction, vibration sample magnetometer, and Mossbauer spectrometer, respectively. The Rietveld analysis of room temperature X-ray diffraction data shows that all the samples were crystallized in Th2Fe17 structure. The unit cell volume of alloys increased linearly with an increase in Nb content. The maximum Curie temperature Tc ~523 K for x = 0.6 sample is higher than Tc = 153 K of Dy2Fe17. The saturation magnetization decreased linearly with increasing Nb content from 61.57 emu/g for x = 0.0 to 42.46 emu/g for x = 1.0. The Mössbauer spectra and Rietveld analysis showed a small amount of DyFe3 and NbFe2 secondary phases at x = 1.0. The hyperfine field of Dy2Fe16Ga1−xNbx decreased while the isomer shift values increased with the Nb content. The observed increase in isomer shift may have resulted from the decrease in s electron density due to the unit cell volume expansion. The substantial increase in Tc of thus prepared intermetallic compounds is expected to have implications in magnets used for high-temperature applications.

Ternary Antimonides RE4T7Sb6 (RE=Gd–Lu; T =Ru, Rh) with Cubic U4Re7Si6-type Structure

2013 ◽  
Vol 68 (9) ◽  
pp. 971-978 ◽  
Author(s):  
Inga Schellenberg ◽  
Ute Ch. Rodewald ◽  
Christian Schwickert ◽  
Matthias Eul ◽  
Rainer Pöttgen
Keyword(s):  
Magnetic Susceptibility ◽  
Single Crystal ◽  
Magnetic Moment ◽  
Induction Furnace ◽  
X Ray Diffraction ◽  
Temperature Dependent ◽  
X Ray ◽  
Antiferromagnetic Ordering ◽  
Arc Melting ◽  
Intermediate Valent

The ternary antimonides RE4T7Sb6 (RE=Gd-Lu; T =Ru, Rh) have been synthesized from the elements by arc-melting and subsequent annealing in an induction furnace. The samples have been characterized by powder X-ray diffraction. Four structures were refined on the basis of single-crystal X-ray diffractometer data: U4Re7Si6 type, space group Im3m with a=862.9(2) pm, wR2=0.0296, 163 F2 values for Er4Ru7Sb6; a=864.1(1) pm, wR2=0.1423, 153 F2 values for Yb4Ru7Sb6; a=872.0(2) pm, wR2=0.0427, 172 F2 values for Tb4Rh7Sb6; and a=868.0(2) pm, wR2=0.0529, 154 F2 values for Er4Rh7Sb6, with 10 variables per refinement. The structures have T1@Sb6 octahedra and slightly distorted RE@T26Sb6 cuboctahedra as building units. The distorted cuboctahedra are condensed via all trapezoidal faces, and this network leaves octahedral voids for the T1 atoms. The ruthenium-based series of compounds was studied by temperature-dependent magnetic susceptibility measurements. Lu4Ru7Sb6 is Pauli-paramagnetic. The antimonides RE4Ru7Sb6 with RE=Dy, Ho, Er, and Tm show Curie-Weiss paramagnetism. Antiferromagnetic ordering occurs at 10.0(5), 5.1(5) and 4.0(5) K for Dy4Ru7Sb6, Ho4Ru7Sb6 and Er4Ru7Sb6, respectively, while Tm4Ru7Sb6 remains paramagnetic. Yb4Ru7Sb6 is an intermediate-valent compound with a reduced magnetic moment of 3.71(1) μB per Yb as compared to 4.54 μB for a free Yb3+ ion

Effect of Nickel on Titanium Carbide Synthesized via Tungsten Inert Gas (TIG) Method

2012 ◽  
Vol 620 ◽  
pp. 384-388
Author(s):  
Sharifah Aishah Syed Salim ◽  
Julie Juliewatty Mohamed ◽  
Zainal Arifin Ahmad ◽  
Zainal Arifin Ahmad
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Powder Mixture ◽  
Raw Material ◽  
Inert Gas ◽  
X Ray Diffraction ◽  
X Ray ◽  
Arc Melting ◽  
Elemental Powder Mixture ◽  
Scanning Electron

Numerous methods have been used to produce high purity TiC. There is no previous study has been reported on the formation using single elemental powders of Titanium (Ti) and Carbon (C) with addition Nickel (Ni) by tungsten inert gas (TIG) weld method. In this work, TiC was synthesized via TIG method by arc melting elemental powder mixture of Ti and C at ~5 second (s) and 80 ampere (A). The effect Ni contents on TiC formation was investigated. The mixed raw material was ball milled for 24 hours followed by synthesis via TIG method. The arced samples were characterized by X-ray diffraction (XRD) and Scanning electron microscope (SEM). It was revealed, that small amount of Ni additive to the metal powder allows the production of dense and tough TiC.

Microstructure and Mechanical Properties of VTaTiMoAlx Refractory High Entropy Alloys

2017 ◽  
Vol 898 ◽  
pp. 638-642 ◽  
Author(s):  
Dong Xu Qiao ◽  
Hui Jiang ◽  
Xiao Xue Chang ◽  
Yi Ping Lu ◽  
Ting Ju Li
Keyword(s):  
Mechanical Properties ◽  
Vacuum Arc ◽  
High Entropy Alloys ◽  
X Ray Diffraction ◽  
Dendrite Structure ◽  
X Ray ◽  
High Entropy ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Microstructure And Mechanical Properties

A series of refractory high-entropy alloys VTaTiMoAlx with x=0,0.2,0.6,1.0 were designed and produced by vacuum arc melting. The effect of added Al elements on the microstructure and mechanical properties of refractory high-entropy alloys were investigated. The X-ray diffraction results showed that all the high-entropy alloys consist of simple BCC solid solution. SEM indicated that the microstructure of VTaTiMoAlx changes from equiaxial dendritic-like structure to typical dendrite structure with the addition of Al element. The composition of different regions in the alloys are obtained by energy dispersive spectroscopy and shows that Ta, Mo elements are enriched in the dendrite areas, and Al, Ti, V are enriched in inter-dendrite areas. The yield strength and compress strain reach maximum (σ0.2=1221MPa, ε=9.91%) at x=0, and decrease with the addition of Al element at room temperature. Vickers hardness of the alloys improves as the Al addition.

Superstructure formation in the solid solution Sc3Pt3−xIn3 (x = 0–0.93)

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Nataliya L. Gulay ◽  
Rolf-Dieter Hoffmann ◽  
Jutta Kösters ◽  
Yaroslav M. Kalychak ◽  
Stefan Seidel ◽  
...  
Keyword(s):  
Solid Solution ◽  
Diffraction Data ◽  
High Frequency ◽  
Lattice Parameters ◽  
X Ray Diffraction ◽  
Space Group ◽  
X Ray ◽  
Platinum Content ◽  
Arc Melting ◽  
Modulation Vector

Abstract The equiatomic indide ScPtIn (ZrNiAl type, space group P 6 ‾ $‾{6}$ 2m) shows an extended solid solution Sc3Pt3–xIn3. Several samples of the Sc3Pt3–xIn3 series were synthesized from the elements by arc-melting and subsequent annealing, or directly in a high frequency furnace. The lowest platinum content was observed for Sc3Pt2.072(3)In3. All samples were characterized by powder X-ray diffraction and their lattice parameters and several single crystals were studied on the basis of precise single crystal X-ray diffractometer data. The correct platinum occupancy parameters were refined from the diffraction data. Decreasing platinum content leads to decreasing a and c lattice parameters. Satellite reflections were observed for the Sc3Pt3–xIn3 crystals with x = 0.31–0.83. These satellite reflections could be described with a modulation vector ( 1 3 , 1 3 , γ ) $\left(\frac{1}{3},\frac{1}{3},\gamma \right)$ ( γ = 1 2 $\gamma =\frac{1}{2}$ c* for all crystals) and are compatible with trigonal symmetry. The interplay of platinum filled vs. empty In6 trigonal prisms is discussed for an approximant structure with space group P3m1.

Gallium-containing Heusler phases ScRh2Ga, ScPd2Ga, TmRh2Ga and LuRh2Ga – magnetic and solid state NMR-spectroscopic characterization

2017 ◽  
Vol 72 (8) ◽  
pp. 609-615
Author(s):  
Lukas Heletta ◽  
Stefan Seidel ◽  
Christopher Benndorf ◽  
Hellmut Eckert ◽  
Rainer Pöttgen
Keyword(s):  
Solid State ◽  
Solid State Nmr ◽  
Spectroscopic Characterization ◽  
Structural Disorder ◽  
X Ray Diffraction ◽  
Temperature Dependent ◽  
Phase Purity ◽  
X Ray ◽  
Arc Melting ◽  
Pauli Paramagnetism

AbstractThe gallium-containing Heusler phases ScRh2Ga, ScPd2Ga, TmRh2Ga and LuRh2Ga have been synthesized by arc-melting of the elements followed by different annealing sequences to improve phase purity. The samples have been studied by powder X-ray diffraction. The structures of Lu0.97Rh2Ga1.03 (Fm3̅m, a=632.94(5) pm, wR2=0.0590, 46 F2 values, seven variables) and Sc0.88Rh2Ga1.12 (a=618.91(4) pm, wR2=0.0284, 44 F2 values, six variables) have been refined from single crystal X-ray diffractometer data. Both gallides show structural disorder through Lu/Ga and Sc/Ga mixing. Temperature dependent magnetic susceptibility measurements showed Pauli paramagnetism for ScRh2Ga, ScPd2Ga, and LuRh2Ga and Curie-Weiss paramagnetism for TmRh2Ga. 45Sc and 71Ga solid state MAS NMR spectroscopic investigations of the Sc containing compounds confirmed the site mixing effects typically observed for Heusler phases. The data indicate that the effect of mixed Sc/Ga occupancy is significantly stronger in ScRh2Ga than in ScPd2Ga.

Single-crystal Data of Ternary Germanides RE2Nb3Ge4 (RE = Sc, Y, Gd–Er, Lu) and Sc2Ta3Ge4 with Ordered Sm5Ge4-type Structure

2013 ◽  
Vol 68 (5-6) ◽  
pp. 625-634 ◽  
Author(s):  
Bastian Reker ◽  
Samir F. Matar ◽  
Ute Ch. Rodewald ◽  
Rolf-Dieter Hoffmann ◽  
Rainer Pöttgen
Keyword(s):  
Rare Earth ◽  
Single Crystal ◽  
Coordination Number ◽  
Electronic Structure Calculations ◽  
Crystal Data ◽  
X Ray Diffraction ◽  
X Ray ◽  
Arc Melting ◽  
Structure Calculations ◽  
The Rare Earth

Small single crystals of the Sm5Ge4-type (space group Pnma) germanides RE2Nb3Ge4 (RE = Sc, Y, Gd-Er, Lu) and Sc2Ta3Ge4 were synthesized by arc-melting of the respective elements. The samples were characterized by powder and single-crystal X-ray diffraction. In all structures, except for Sc2.04Nb2.96Ge4 and Sc2.19Ta2.81Ge4, the rare earth and niobium atoms show full ordering on the three crystallographically independent samarium sites of the Sm5Ge4 type. Two sites with coordination number 6 are occupied by niobium, while the slightly larger site with coordination number 7 is filled with the rare earth element. Small homogeneity ranges with RE=Nb and RE=Ta mixing can be expected for all compounds. The ordered substitution of two rare earth sites by niobium or tantalum has drastic effects on the coordination number and chemical bonding. This was studied for the pair Y5Ge4/Y2Nb3Ge4. Electronic structure calculations show larger charge transfer from yttrium to germanium for Y5Ge4, contrary to Y2Nb3Ge4 which shows stronger covalent bonding due to the presence of Nb replacing Y at two sites

scholarly journals Study on the nonexistence of liquid miscibility gap in the Ce-Mn system

2007 ◽  
Vol 43 (1) ◽  
pp. 21-28 ◽  
Author(s):  
C. Tang ◽  
Y. Du ◽  
H. Xu ◽  
S. Hao ◽  
L. Zhang
Keyword(s):  
Xrd Analysis ◽  
Miscibility Gap ◽  
Composition Analysis ◽  
Phase Identification ◽  
X Ray Diffraction ◽  
X Ray ◽  
Microstructure Observation ◽  
Arc Melting ◽  
Ice Water ◽  
Liquid Miscibility Gap

To ascertain whether the liquid miscibility gap exists in the Ce-Mn system, 3 key alloys are prepared by arc melting the pure elements, annealed at specified temperature for 20 minutes, quenched in ice water and then subjected to X-ray diffraction (XRD) analysis for phase identification and to scanning electron microscopy (SEM) with energy dispersive X-ray analysis for microstructure observation and composition analysis. The XRD examination indicated that terminal solutions based on Ce and Mn exist in the water-quenched alloys. No compound was detected. Microstructure observation and composition analysis indicate the nonexistence of the liquid miscibility gap. The newly assessed Ce-Mn phase diagram was presented. .

scholarly journals CRYSTAL STRUCTURE OF THE NEW SILICIDE Lu3Ni11.74(2)Si4

2020 ◽  
Vol 86 (5) ◽  
pp. 3-12
Author(s):  
Bohdana Belan ◽  
Mykola Manyako ◽  
Mariya Dzevenko ◽  
Dorota Kowalska ◽  
Roman Gladyshevskii
Keyword(s):  
Crystal Structure ◽  
Single Crystal ◽  
Type Structure ◽  
X Ray Diffraction ◽  
Space Group ◽  
X Ray ◽  
Arc Melting ◽  
Pearson Symbol ◽  
Ternary Silicide

The new ternary silicide Lu3Ni11.74(2)Si4 was synthesized from the elements by arc-melting and its crystal structure was determined by the single-crystal X-ray diffraction. The compound crystallizes in the Sc3Ni11Ge4-type: Pearson symbol hP37.2, space group P63/mmc (No. 194), a = 8.0985(16), c = 8.550(2) Å, Z = 2; R = 0.0244, wR = 0.0430 for 244 reflections. The silicide Lu3Ni11.74(2)Si4 is new member of the EuMg5.2-type structure family.

Sign in / Sign up

Export Citation Format

Share Document