scholarly journals Synthesis of Fe2SiO4-Fe7Co3 Nanocomposite Dispersed in the Mesoporous SBA-15: Application as Magnetically Separable Adsorbent

Molecules ◽  
2020 ◽  
Vol 25 (4) ◽  
pp. 1016 ◽  
Author(s):  
Monickarla da Silva ◽  
Felipe Barbosa ◽  
Marco Morales Torre ◽  
Jhonny Villarroel-Rocha ◽  
Karim Sapag ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Santa Barbara ◽  
Mesoporous Support ◽  
Magnetically Separable ◽  
Temperature Programmed ◽  
Positive Effect ◽  
Isolated Species

The mixture containing alloy and oxide with iron-based phases has shown interesting properties compared to the isolated species and the synergy between the phases has shown positive effect on dye adsorption. This paper describes the synthesis of Fe2SiO4-Fe7Co3-based nanocomposite dispersed in Santa Barbara Amorphous (SBA)-15 and its application in dye adsorption followed by magnetic separation. Thus, it was studied the variation of reduction temperature and amount of hydrogen used in synthesis and the effect of these parameters on the physicochemical properties of the iron and cobalt based oxide/alloy mixture, as well as the methylene blue adsorption capacity. The XRD and Mössbauer results, along with the temperature-programmed reduction (TPR) profiles, confirmed the formation of Fe2SiO4-Fe7Co3-based nanocomposites. Low-angle XRD, N2 isotherms, and TEM images show the formation of the SBA-15 based mesoporous support with a high surface area (640 m2/g). Adsorption tests confirmed that the material reduced at 700 °C using 2% of H2 presented the highest adsorption capacity (49 mg/g). The nanocomposites can be easily separated from the dispersion by applying an external magnetic field. The interaction between the dye and the nanocomposite occurs mainly by π-π interactions and the mixture of the Fe2SiO4 and Fe7Co3 leads to a synergistic effect, which favor the adsorption.

scholarly journals Effective Poly (Cyclotriphosphazene-Co-4,4′-Sulfonyldiphenol)@rGO Sheets for Tetracycline Adsorption: Fabrication, Characterization, Adsorption Kinetics and Thermodynamics

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1540
Author(s):  
Muhammad Ahmad ◽  
Tehseen Nawaz ◽  
Mohammad Mujahid Alam ◽  
Yasir Abbas ◽  
Shafqat Ali ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Surface Area ◽  
High Surface ◽  
High Surface Area ◽  
High Adsorption ◽  
Clean Environment ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
High Adsorption Capacity ◽  
Adsorption Equilibrium Data

The development of excellent drug adsorbents and clarifying the interaction mechanisms between adsorbents and adsorbates are greatly desired for a clean environment. Herein, we report that a reduced graphene oxide modified sheeted polyphosphazene (rGO/poly (cyclotriphosphazene-co-4,4′-sulfonyldiphenol)) defined as PZS on rGO was used to remove the tetracycline (TC) drug from an aqueous solution. Compared to PZS microspheres, the adsorption capacity of sheeted PZS@rGO exhibited a high adsorption capacity of 496 mg/g. The adsorption equilibrium data well obeyed the Langmuir isotherm model, and the kinetics isotherm was fitted to the pseudo-second-order model. Thermodynamic analysis showed that the adsorption of TC was an exothermic, spontaneous process. Furthermore, we highlighted the importance of the surface modification of PZS by the introduction of rGO, which tremendously increased the surface area necessary for high adsorption. Along with high surface area, electrostatic attractions, H-bonding, π-π stacking and Lewis acid-base interactions were involved in the high adsorption capacity of PZS@rGO. Furthermore, we also proposed the mechanism of TC adsorption via PZS@rGO.

Fabricate Dye-Sensitized Solar Cell with Electrospining

2011 ◽  
Vol 335-336 ◽  
pp. 1117-1120
Author(s):  
Yun Yun Chu ◽  
Yu Chou Chao
Keyword(s):  
Solar Cell ◽  
Electron Transport ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Dye Sensitized Solar Cell ◽  
High Electron ◽  
Solar Cell Performance ◽  
Dye Sensitized ◽  
Viable Method

Dye adsorption on Ti02and electron transport in Ti02film are the two critical factors in determining efficiency of the the dye sensitized solar cell (DSSC). Increasing dye adsorption which increases the light harvesting is usually achieved by using nanoporous or nanoparticle Ti02films. Electron transport is determined by the inter-particle resistance of Ti02film. Electrospinning is a viable method for forming porous structure materials with high surface area. In this study, it was found that electrospinning is able to achieve good solar cell performance due to the high electron transport caused by the pores in the Ti02film.

scholarly journals Experimental and Modeling of Dicamba Adsorption in Aqueous Medium Using MIL-101(Cr) Metal-Organic Framework

Processes ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 419
Author(s):  
Hamza Ahmad Isiyaka ◽  
Khairulazhar Jumbri ◽  
Nonni Soraya Sambudi ◽  
Jun Wei Lim ◽  
Bahruddin Saad ◽  
...  
Keyword(s):  
Aqueous Medium ◽  
Adsorption Capacity ◽  
Environmental Concern ◽  
Metal Organic Framework ◽  
High Surface ◽  
High Surface Area ◽  
Data Matrix ◽  
Adsorption Parameters ◽  
Metal Organic ◽  
Organic Framework

Drift deposition of emerging and carcinogenic contaminant dicamba (3,6-dichloro-2-methoxy benzoic acid) has become a major health and environmental concern. Effective removal of dicamba in aqueous medium becomes imperative. This study investigates the adsorption of a promising adsorbent, MIL-101(Cr) metal-organic framework (MOF), for the removal of dicamba in aqueous solution. The adsorbent was hydrothermally synthesized and characterized using N2 adsorption-desorption isotherms, Brunauer, Emmett and Teller (BET), powdered X-ray diffraction (XRD), Fourier Transformed Infrared (FTIR) and field emission scanning electron microscopy (FESEM). Adsorption models such as kinetics, isotherms and thermodynamics were studied to understand details of the adsorption process. The significance and optimization of the data matrix, as well as the multivariate interaction of the adsorption parameters, were determined using response surface methodology (RSM). RSM and artificial neural network (ANN) were used to predict the adsorption capacity. In each of the experimental adsorption conditions used, the ANN gave a better prediction with minimal error than the RSM model. The MIL-101(Cr) adsorbent was recycled six times to determine the possibility of reuse. The results show that MIL-101(Cr) is a very promising adsorbent, in particular due to the high surface area (1439 m2 g−1), rapid equilibration (~25 min), high adsorption capacity (237.384 mg g−1) and high removal efficiency of 99.432%.

Facile and large-scale synthesis of poly(m-phenylenediamine) nanobelts with high surface area and superior dye adsorption ability

RSC Advances ◽  
2014 ◽  
Vol 4 (85) ◽  
pp. 45244-45250 ◽  
Author(s):  
Yun Meng ◽  
Liyuan Zhang ◽  
Liyuan Chai ◽  
Wanting Yu ◽  
Ting Wang ◽  
...  
Keyword(s):  
Surface Area ◽  
Large Scale ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
High Adsorption ◽  
Adsorption Ability ◽  
Adsorption Performance ◽  
Large Scale Synthesis

PmPD nanobelts with high adsorption performance have been synthesized by using CTAP as oxidants.

Morphology dependent adsorption of methylene blue on trititanate nanoplates and nanotubes prepared by the hydrothermal treatment of TiO2

2016 ◽  
Vol 75 (2) ◽  
pp. 350-357
Author(s):  
Graham Dawson ◽  
Wei Chen ◽  
Luhua Lu ◽  
Kai Dai
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Pore Volume ◽  
Hydrothermal Reaction ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
High Capacity ◽  
Adsorption Properties

The adsorption properties of two nanomorphologies of trititanate, nanotubes (TiNT) and plates (TiNP), prepared by the hydrothermal reaction of concentrated NaOH with different phases of TiO2, were examined. It was found that the capacity for both morphologies towards methylene blue (MB), an ideal pollutant, was extremely high, with the TiNP having a capacity of 130 mg/g, higher than the TiNT, whose capacity was 120 mg/g at 10 mg/L MB concentration. At capacity, the well-dispersed powders deposit on the floor of the reaction vessel. The two morphologies had very different structural and adsorption properties. TiNT with high surface area and pore volume exhibited exothermic monolayer adsorption of MB. TiNP with low surface area and pore volume yielded a higher adsorption capacity through endothermic multilayer adsorption governed by pore diffusion. TiNP exhibited a higher negative surface charge of −23 mV, compared to −12 mV for TiNT. The adsorption process appears to be an electrostatic interaction, with the cationic dye attracted more strongly to the nanoplates, resulting in a higher adsorption capacity and different adsorption modes. We believe this simple, low cost production of high capacity nanostructured adsorbent material has potential uses in wastewater treatment.

scholarly journals Microporous activated carbon developed from KOH activated biomass waste: surface mechanistic study of methylene blue dye adsorption

2021 ◽  
Author(s):  
Ali H. Jawad ◽  
Ahmed Saud Abdulhameed ◽  
Noor Nazihah Bahrudin ◽  
Nurul Nadiah Mohd Firdaus Hum ◽  
S. N. Surip ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Sugarcane Bagasse ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Type I ◽  
Order Kinetic ◽  
Bagasse Waste

Abstract In this work, sugarcane bagasse waste (SBW) was used as a lignocellulosic precursor to develop a high surface area activated carbon (AC) by thermal treatment of the SBW impregnated with KOH. This sugarcane bagasse waste activated carbon (SBWAC) was characterized by means of crystallinity, porosity, surface morphology and functional groups availability. The SBWAC exhibited Type I isotherm which corresponds to microporosity with high specific surface area of 709.3 m2/g and 6.6 nm of mean pore diameter. Further application of SBWAC as an adsorbent for methylene blue (MB) dye removal demonstrated that the adsorption process closely followed the pseudo-second order kinetic and Freundlich isotherm models. On the other hand, thermodynamic study revealed the endothermic nature and spontaneity of MB dye adsorption on SBWAC with high acquired adsorption capacity (136.5 mg/g). The MB dye adsorption onto SBWAC possibly involved electrostatic interaction, H-bonding and π-π interaction. This work demonstrates SBW as a potential lignocellulosic precursor to produce high surface area AC that can potentially remove more cationic dyes from the aqueous environment.

scholarly journals Preparation of MoS2 nano-corals by hydrothermal method for adsorption of tartrazine in the aqueous medium

2020 ◽  
Vol 9 (4) ◽  
pp. 93-99
Author(s):  
Hung Mac Van ◽  
Tuan Vu Anh
Keyword(s):  
Adsorption Capacity ◽  
Hydrothermal Method ◽  
Adsorption Kinetics ◽  
Organic Dyes ◽  
Nile Blue ◽  
High Surface ◽  
High Surface Area ◽  
Optimal Dosage ◽  
Solution Ph ◽  
Intra Particle Diffusion

Corals-like molybdenum disulfide (MoS2) have been successfully synthesized via the hydrothermal method. The as-prepared MoS2 material with a high surface area of 83.9 m2.g-1 was used for the removal of tartrazine from an aqueous solution. The effects of parameters including contact time, MoS2 dosage, and solution pH on adsorption capacity were studied. The optimal dosage of MoS2 for removing tartrazine was 0.08 g and the removal efficiency of tartrazine reached 81.5 % for 100 min of adsorption. The adsorption kinetics studies were carried out using pseudo-first-order, pseudo-second-order, and intra-particle diffusion models. The results showed that the pseudo-second-kinetic model better described the adsorption kinetics of tartrazine on MoS2 and film diffusion was the rate-limiting step. In addition, the adsorption capacity of MoS2 was also performed with various organic dyes such as nile blue, janus green B, and congo red.

scholarly journals Adsorption of Mn2+ from Aqueous Solution Using Manganese Oxide-Coated Hollow Polymethylmethacrylate Microspheres (MHPM)

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Dhiraj Dutta ◽  
Jyoti Prasad Borah ◽  
Amrit Puzari
Keyword(s):  
Aqueous Solution ◽  
Manganese Oxide ◽  
Adsorption Capacity ◽  
High Surface ◽  
High Surface Area ◽  
Freundlich Isotherm ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Coated Sand

Results of investigation on adsorption of Mn2+ from aqueous solution by manganese oxide-coated hollow polymethylmethacrylate microspheres (MHPM) are reported here. This is the first report on Mn-coated hollow polymer as a substitute for widely used materials like green sand or MN-coated sand. Hollow polymethylmethacrylate (HPM) was prepared by using a literature procedure. Manganese oxide (MnO) was coated on the surface of HPM (MHPM) by using the electroless plating technique. The HPM and MHPM were characterized by using optical microscopy (OM), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Optical and scanning micrographs were used to monitor the surface properties of the coated layer which revealed the presence of MnO on the surface of HPM. TGA showed the presence of 4-5% of MnO in MHPM. Adsorption isotherm studies were carried out as a function of pH, initial ion concentration, and contact time, to determine the adsorption efficiency for removal of Mn2+ from contaminated water by the synthesized MHPM. The isotherm results showed that the maximum adsorption capacity of MnO-coated HPM to remove manganese contaminants from water is 8.373 mg/g. The obtained R 2 values of Langmuir isotherm and Freundlich isotherm models were 1 and 0.87, respectively. Therefore, R 2 magnitude confirmed that the Langmuir model is best suited for Mn2+ adsorption by a monolayer of MHPM adsorbent. The material developed shows higher adsorption capacity even at a higher concentration of solute ions, which is not usually observed with similar materials of this kind. Overall findings indicate that MHPM is a very potential lightweight adsorbent for removal of Mn2+ from the aqueous solution because of its low density and high surface area.

Sign in / Sign up

Export Citation Format

Share Document