scholarly journals Mechanical and Morphological Properties of Bio-Phenolic/Epoxy Polymer Blends

Molecules ◽  
2021 ◽  
Vol 26 (4) ◽  
pp. 773
Author(s):  
Ahmad Safwan Ismail ◽  
Mohammad Jawaid ◽  
Norul Hisham Hamid ◽  
Ridwan Yahaya ◽  
Azman Hassan
Keyword(s):  
Mechanical Properties ◽  
Phase Separation ◽  
Polymer Blends ◽  
Epoxy Polymer ◽  
Flexural Modulus ◽  
Polymeric Materials ◽  
Morphological Properties ◽  
Comparison Results ◽  
Unique Material ◽  
Different Types

Polymer blends is a well-established and suitable method to produced new polymeric materials as compared to synthesis of a new polymer. The combination of two different types of polymers will produce a new and unique material, which has the attribute of both polymers. The aim of this work is to analyze mechanical and morphological properties of bio-phenolic/epoxy polymer blends to find the best formulation for future study. Bio-phenolic/epoxy polymer blends were fabricated using the hand lay-up method at different loading of bio-phenolic (5 wt%, 10 wt%, 15 wt%, 20 wt%, and 25 wt%) in the epoxy matrix whereas neat bio-phenolic and epoxy samples were also fabricated for comparison. Results indicated that mechanical properties were improved for bio-phenolic/epoxy polymer blends compared to neat epoxy and phenolic. In addition, there is no sign of phase separation in polymer blends. The highest tensile, flexural, and impact strength was shown by P-20(biophenolic-20 wt% and Epoxy-80 wt%) whereas P-25 (biophenolic-25 wt% and Epoxy-75 wt%) has the highest tensile and flexural modulus. Based on the finding, it is concluded that P-20 shows better overall mechanical properties among the polymer blends. Based on this finding, the bio-phenolic/epoxy blend with 20 wt% will be used for further study on flax-reinforced bio-phenolic/epoxy polymer blends.

scholarly journals Effects of Irradiation by UV- Acceleration on Mechanical Properties of Polymer Blends (Polyester: Starch)

2018 ◽  
Vol 21 (1) ◽  
pp. 147 ◽  
Author(s):  
Sihama I. Salih ◽  
Qahtan A. Hamad ◽  
Safaa N. Abdul Jabbar ◽  
Najat H. Sabit
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Polymer Blends ◽  
Modulus Of Elasticity ◽  
Unsaturated Polyester ◽  
Flexural Modulus ◽  
Weight Ratio ◽  
Weight Fraction ◽  
Elongation Percentage

This work covers mixing of unsaturated polyester (un- polyester) with starch powders as polymer blends and study the effects of irradiation by UV-acceleration on mechanical properties of its. The unsaturated polyester was mixing by starch powders at particle size less than (45 µm) at selected weight fraction of (0, 0.5, 1, 1.5, 2, 2.5 and 3%). These properties involve ultimate tensile strength, modulus of elasticity, elongation percentage, flexural modulus, flexural strength, fracture toughness, impact strength and hardness. The results illustrate decrease in the ultimate tensile strength at and elongation percentage, while increasing modulus of elasticity, with increasing the weight ratio of starch powder to 3 % weight fraction, whereas the maximum value of hardness and flexural, impact properties happened at 1 % weight fraction for types of polymer blends.

Location Depending Textures of the Human Dental Enamel

2010 ◽  
Vol 160 ◽  
pp. 281-286 ◽  
Author(s):  
Lars Raue ◽  
Helmut Klein
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Dental Enamel ◽  
Polymeric Materials ◽  
Incisor Tooth ◽  
Worst Case ◽  
Dental Fillings ◽  
Anisotropic Mechanical Properties ◽  
Different Types ◽  
Materials Used

Dental enamel is the most highly mineralised and hardest biological tissue in human body [1]. Dental enamel is made of hydroxylapatite (HAP) - Ca5(PO4)3(OH), which is hexagonal (6/m). The lattice parameters are a = b = 0.9418 nm und c = 0.6875 nm [1]. Although HAP is a very hard mineral, it can be dissolved easily in a process which is known as enamel demineralization by lactic acid produced by bacteria. Also the direct consumption of acid (e.g. citric, lactic or phosphoric acid in soft drinks) can harm the dental enamel in a similar way. These processes can damage the dental enamel. It will be dissolved completely and a cavity occurs. The cavity must then be cleaned and filled. It exists a lot of dental fillings, like gold, amalgam, ceramics or polymeric materials. After filling other dangers can occur: The mechanical properties of the materials used to fill cavities can differ strongly from the ones of the dental enamel itself. In the worst case, the filling of a tooth can damage the enamel of the opposite tooth by chewing if the interaction of enamel and filling is not equivalent, so that the harder fillings can abrade the softer enamel of the healthy tooth at the opposite side. This could be avoided if the anisotropic mechanical properties of dental enamel would be known in detail, hence then another filling could be searched or fabricated as an equivalent opponent for the dental enamel with equal properties. To find such a material, one has to characterise the properties of dental enamel first in detail for the different types of teeth (incisor, canine, premolar and molar). This is here exemplary done for a human incisor tooth by texture analysis with the program MAUD from 2D synchrotron transmission images [2,3,4].

scholarly journals Effect of MWCNT on Thermal, Mechanical, and Morphological Properties of Polybutylene Terephthalate/Polycarbonate Blends

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
C. P. Rejisha ◽  
S. Soundararajan ◽  
N. Sivapatham ◽  
K. Palanivelu
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Nucleating Agent ◽  
Mechanical Analysis ◽  
Morphological Properties ◽  
Multiwall Carbon Nanotube ◽  
Polybutylene Terephthalate ◽  
The Impact

This paper evaluated the effect of multiwall carbon nanotube (MWCNT) on the properties of PBT/PC blends. The nanocomposites were obtained by melt blending MWCNT in the weight percentages 0.15, 0.3, and 0.45 wt% with PBT/PC blends in a high performance corotating twin screw extruder. Samples were characterized by tensile testing, dynamic mechanical analysis, thermal analysis, scanning electron microscopy, and X-ray diffraction. Concentrations of PBT and PC are optimized as 80 : 20 based on mechanical properties. A small amount of MWCNT shows better increase in the thermal and mechanical properties of the blends of PBT/PC nanocomposite when compared to nanoclays or inorganic fillers. The ultimate tensile strength of the nanocomposites increased from 54 MPa to 85 MPa with addition of MWCNT up to 0.3% and then decreased.The tensile modulus values were increased to about 60% and the flexural modulus was more than about 80%. The impact strength was also improved with 20% PC to about 60% and with 0.15% MWCNT to about 50%. The HDT also improved from 127°C to 205°C. It can be seen from XRD result that the crystallinity of PBT is less affected by incorporating MWCNT. The crystallizing temperature was increased and the MWCNT may act as a strong nucleating agent.

scholarly journals Mechanical and Morphological Properties of Polypropylene/Nanoα-Al2O3Composites

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
F. Mirjalili ◽  
L. Chuah ◽  
E. Salahi
Keyword(s):  
Mechanical Properties ◽  
Flexural Modulus ◽  
Mechanical Tests ◽  
Filler Loading ◽  
Morphological Properties ◽  
Electron Microscopic ◽  
Scanning Electron Microscopic ◽  
Flexural Analysis ◽  
Flexural Tests ◽  
Internal Mixer

A nanocomposite containing polypropylene (PP) and nanoα-Al2O3particles was prepared using a Haake internal mixer. Mechanical tests, such as tensile and flexural tests, showed that mechanical properties of the composite were enhanced by addition of nanoα-Al2O3particles and dispersant agent to the polymer. Tensile strength was approximately∼16% higher than pure PP by increasing the nanoα-Al2O3loading from 1 to 4 wt% into the PP matrix. The results of flexural analysis indicated that the maximum values of flexural strength and flexural modulus for nanocomposite without dispersant were 50.5 and 1954 MPa and for nanocomposite with dispersant were 55.88 MPa and 2818 MPa, respectively. However, higher concentration of nanoα-Al2O3loading resulted in reduction of those mechanical properties that could be due to agglomeration of nanoα-Al2O3particles. Transmission and scanning electron microscopic observations of the nanocomposites also showed that fracture surface became rougher by increasing the content of filler loading from 1 to 4% wt.

scholarly journals Recycled Polymer Materials as Aggregates for Concrete and Blocks

2013 ◽  
Vol 27 ◽  
pp. 53-57 ◽  
Author(s):  
Md Mostafizur Rahman ◽  
Md Akhtarul Islam ◽  
Mainuddin Ahmed ◽  
Md Abdus Salam
Keyword(s):  
Chemical Engineering ◽  
Polymeric Materials ◽  
Polymer Materials ◽  
Morphological Properties ◽  
Light Weight ◽  
Floating Structures ◽  
Different Types ◽  
Waste Polymer ◽  
Recycled Waste ◽  
Recycled Polymer

The potential of recycled waste polymeric materials as a substitute for aggregates in concrete has been investigated in the study. Two different types of waste polymer, namely polyurethane formaldehyde (PUF) based packaging waste and high density polyethylene (HDPE) were recycled and used in the experiment. Concrete and masonry poly block specimens were prepared using recycled polymer materials, and test specimens were characterized. The effects of waste polymer materials on the mechanical, physical and morphological properties of concrete and poly blocks have been investigated. The result shows that the inclusion of waste polymer materials decreases density, porosity and water absorption of concrete and poly blocks significantly. Polyurethane formaldehyde (PUF) based block exhibited lower density than that of HDPE-based concrete. Due to exceptionally low density, recycled polymer modified blocks and concrete can be used in non-load bearing structures, floating structures and where light weight materials recommended. DOI: http://dx.doi.org/10.3329/jce.v27i1.15859 Journal of Chemical Engineering, IEB Vol. ChE. 27, No. 1, June 2012: 53-57

scholarly journals Manufacturing of Porous Polycaprolactone Prepared with Different Particle Sizes and Infrared Laser Sintering Conditions: Microstructure and Mechanical Properties

2014 ◽  
Vol 6 ◽  
pp. 640496 ◽  
Author(s):  
G. V. Salmoria ◽  
D. Hotza ◽  
P. Klauss ◽  
L. A. Kanis ◽  
C. R. M. Roesler
Keyword(s):  
Mechanical Properties ◽  
Energy Density ◽  
Laser Energy ◽  
Flexural Modulus ◽  
Selective Laser Sintering ◽  
Polymeric Materials ◽  
Laser Sintering ◽  
Laser Energy Density ◽  
Particle Sizes ◽  
Mechanical Devices

The techniques of Rapid Prototyping, also known as Additive Manufacturing, have prompted research into methods of manufacturing polymeric materials with controlled porosity. This paper presents the characterization of the structure and mechanical properties of porous polycaprolactone (PCL) fabricated by Selective Laser Sintering (SLS) using two different particle sizes and laser processing conditions. The results of this study indicated that it is possible to control the microstructure, that is, pore size and degree of porosity, of the polycaprolactone matrix using the SLS technique, by varying the particle size and laser energy density, obtaining materials suitable for different applications, scaffolds and drug delivery and fluid mechanical devices. The specimens manufactured with smaller particles and higher laser energy density showed a higher degree of sintering, flexural modulus, and fatigue resistance when compared with the other specimens.

Rheology of Immiscible Polymer Blends

2007 ◽  
Author(s):  
Chang Dae Han
Keyword(s):  
Mechanical Properties ◽  
Polymer Blends ◽  
Experimental Studies ◽  
Polymeric Materials ◽  
Random Copolymer ◽  
Random Copolymers ◽  
Immiscible Polymer Blends ◽  
Blend Morphology ◽  
Immiscible Polymer ◽  
New Findings

The polymer industry has been challenged to produce new polymeric materials by blending two or more homopolymers or random copolymers or by synthesizing graft copolymers. To meet the challenge, various methods have been explored, namely, (1) by synthesizing a new monomer, polymerizing it, and then blending it with an existing homopolymer or random copolymer, (2) by copolymerizing existing monomers and then blending it with an existing homopolymer or random copolymer, (3) by chemically modifying an existing homopolymer or random copolymer and then blending it with other homopolymers or copolymers already available, or (4) by synthesizing new compatibilizer(s) to improve the mechanical properties of two immiscible homopolymers or random copolymers that otherwise have unacceptable mechanical properties. There are numerous monographs (Cooper and Estes 1979; Han 1984; Paul and Newman 1978; Platzer 1971, 1975; Sperling 1974; Utracki 1990) describing various aspects of polymer blends. In the 1970s, Han and coworkers (Han 1971, 1974; Han and Kim 1975; Han and Yu 1971a, 1971b, 1972; Han et al. 1973, 1975; Kim and Han 1976) conducted seminal experimental studies on the rheology of immiscible polymer blends and related the observed rheological behavior to blend morphology. Independently, in the same period, Vinogradov and coworkers (Ablazova et al. 1975; Brizitsky et al. 1978; Tsebrenko et al. 1974, 1976; Vinogradov et al. 1975) conducted a series of experimental studies relating the blend rheology to blend morphology. Van Oene (1972, 1978) also pursued, independently, experimental studies for a better understanding of rheology–morphology relationships in immiscible polymer blends. Since then, using different polymer pairs, numerous researchers have conducted experimental studies, which were essentially the same as, or very similar to, the previous experimental studies of Han and coworkers, Vinogradov and coworkers, and van Oene in the 1970s. It is fair to state that those studies in the 1980s and 1990s have not revealed any significant new findings.

scholarly journals Hybrid Cellulose-Glass Fiber Composites for Automotive Applications

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3189 ◽  
Author(s):  
Annandarajah ◽  
Langhorst ◽  
Kiziltas ◽  
Grewell ◽  
Mielewski ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Fiber Composite ◽  
Glass Fibers ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
Polyamide 6 ◽  
Morphological Properties ◽  
Hybrid Fibers ◽  
Glass Fiber Composites

: In the recent years, automakers have been striving to improve the carbon footprint of their vehicles. Sustainable composites, consisting of natural fibers, and/or recycled polymers have been developed as a way to increase the “green content” and reduce the weight of a vehicle. In addition, recent studies have found that the introduction of synthetic fibers to a traditional fiber composite such as glass filled plastics, producing a composite with multiple fillers (hybrid fibers), can result in superior mechanical properties. The objective of this work was to investigate the effect of hybrid fibers on characterization and material properties of polyamide-6 (PA6)/polypropylene (PP) blends. Cellulose and glass fibers were used as fillers and the mechanical, water absorption, and morphological properties of composites were evaluated. The addition of hybrid fibers increased the stiffness (tensile and flexural modulus) of the composites. Glass fibers reduced composite water absorption while the addition of cellulose fibers resulted in higher composite stiffness. The mechanical properties of glass and cellulose filled PA6/PP composites were optimized at loading levels of 15 wt% glass and 10 wt% cellulose, respectively.

Effects of different starch types on the physico-mechanical and morphological properties of low density polyethylene composites

2015 ◽  
Vol 35 (8) ◽  
pp. 793-804 ◽  
Author(s):  
Md. Dalour Hossen Beg ◽  
Shaharuddin Bin Kormin ◽  
Mohd Bijarimi ◽  
Haydar U. Zaman
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Water Absorption ◽  
Starch Content ◽  
Flexural Modulus ◽  
Morphological Properties ◽  
Low Density Polyethylene ◽  
Flow Index ◽  
Low Density ◽  
Sago Starch

Abstract The aim of this research is to investigate the effects of different thermoplastic starches and starch contents on the physico-mechanical and morphological properties of new polymeric-based composites from low density polyethylene (LDPE) and thermoplastic starches. Different compositions of thermoplastic starches (5–40 wt%) and LDPE were melt blended by extrusion and injection molding. The resultant materials were characterized with respect to the following parameters, i.e., melt flow index (MFI), mechanical properties (tensile, flexural, stiffness and impact strength) and water absorption. Scanning electron microscopy (SEM) was also used in this study for evaluating blend miscibility. MFI values of all blends decreased as the starch content increased, while the sago starch formulation showed a higher MFI value than others. The incorporation of fillers into LDPE matrix resulted in an increased in tensile modulus, flexural strength, flexural modulus and slightly decreased tensile strength and impact strength. However, sago starch filled composites exhibited better mechanical properties as compared to other starches. The SEM results revealed that the miscibility of such blends is dependent on the type of starch used. The water absorption increased with immersion time and the thermoplastic sago starch samples showed the lowest percentage of water absorption compared with other thermoplastic starches.

scholarly journals Effect of Curing Temperature on Mechanical Properties of Bio-phenolic/Epoxy Polymer Blends

2021 ◽  
Author(s):  
Ahmad Safwan Ismail ◽  
Mohammad Jawaid ◽  
Norul Hisham Hamid ◽  
Ridwan Yahaya ◽  
Azman Hassan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polymer Blends ◽  
Epoxy Polymer ◽  
Curing Temperature
Sign in / Sign up

Export Citation Format

Share Document