scholarly journals Effect of MWCNT on Thermal, Mechanical, and Morphological Properties of Polybutylene Terephthalate/Polycarbonate Blends

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
C. P. Rejisha ◽  
S. Soundararajan ◽  
N. Sivapatham ◽  
K. Palanivelu
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Nucleating Agent ◽  
Mechanical Analysis ◽  
Morphological Properties ◽  
Multiwall Carbon Nanotube ◽  
Polybutylene Terephthalate ◽  
The Impact

This paper evaluated the effect of multiwall carbon nanotube (MWCNT) on the properties of PBT/PC blends. The nanocomposites were obtained by melt blending MWCNT in the weight percentages 0.15, 0.3, and 0.45 wt% with PBT/PC blends in a high performance corotating twin screw extruder. Samples were characterized by tensile testing, dynamic mechanical analysis, thermal analysis, scanning electron microscopy, and X-ray diffraction. Concentrations of PBT and PC are optimized as 80 : 20 based on mechanical properties. A small amount of MWCNT shows better increase in the thermal and mechanical properties of the blends of PBT/PC nanocomposite when compared to nanoclays or inorganic fillers. The ultimate tensile strength of the nanocomposites increased from 54 MPa to 85 MPa with addition of MWCNT up to 0.3% and then decreased.The tensile modulus values were increased to about 60% and the flexural modulus was more than about 80%. The impact strength was also improved with 20% PC to about 60% and with 0.15% MWCNT to about 50%. The HDT also improved from 127°C to 205°C. It can be seen from XRD result that the crystallinity of PBT is less affected by incorporating MWCNT. The crystallizing temperature was increased and the MWCNT may act as a strong nucleating agent.

Mechanical properties of unidirectional aligned bagasse fibers/vinyl ester composite

2016 ◽  
Vol 36 (2) ◽  
pp. 157-163 ◽  
Author(s):  
Ayyanar Athijayamani ◽  
Balasubramaniam Stalin ◽  
Susaiyappan Sidhardhan ◽  
Azeez Batcha Alavudeen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Vinyl Ester ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Short Beam ◽  
Beam Shear ◽  
The Matrix ◽  
The Impact

Abstract The present study describes the preparation of aligned unidirectional bagasse fiber-reinforced vinyl ester (BFRVE) composites and their mechanical properties such as tensile, flexural, shear and impact strength. Composites were prepared by a hand lay-up technique developed in our laboratory with the help of a hot press. Mechanical properties were obtained for different fiber contents by varying the number of layers. The obtained tensile property values were compared with the theoretical results. The results show that the tensile strength increased linearly up to 44 wt% and then dropped. However, the tensile modulus increased linearly from 17 wt% to 60 wt%. In the case of flexural properties, the flexural strength increased up to 53 wt% and started to decrease. However, the flexural modulus also increased linearly up to 60 wt%. The impact strength values were higher than the matrix materials for all the specimens. The short beam shear strength values were also increased up to 53 wt% and then dropped. The modified Bowyer and Bader (MBB) model followed by the Hirsch model shows a very good agreement with experimental results in both tensile strength and modulus.

scholarly journals Mechanical, Thermal, and Morphological Properties of Nanocomposites Based on Polyvinyl Alcohol and Cellulose Nanofiber fromAloe veraRind

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Adel Ramezani Kakroodi ◽  
Shuna Cheng ◽  
Mohini Sain ◽  
Abdullah Asiri
Keyword(s):  
Mechanical Properties ◽  
Polyvinyl Alcohol ◽  
Elevated Temperatures ◽  
Aqueous Suspension ◽  
Cellulose Nanofibers ◽  
Aloe Vera ◽  
Tensile Modulus ◽  
Mechanical Analysis ◽  
Cellulose Nanofiber ◽  
Morphological Properties

This work was devoted to reinforcement of polyvinyl alcohol (PVA) using cellulose nanofibers fromAloe verarind. Nanofibers were isolated fromAloe verarind in the form of an aqueous suspension using chemimechanical technique. Mechanical characterizations showed that incorporation of even small amounts of nanofibers (as low as 2% by weight) had significant effects on both the modulus and strength of PVA. Tensile modulus and strength of PVA increased, 32 and 63%, respectively, after adding 2% of cellulose nanofiber fromAloe verarind. Samples with higher concentrations of nanofibers also showed improved mechanical properties due to a high level of interfacial adhesion and also dispersion of fibers. The results showed that inclusion of nanofibers decreased deformability of PVA significantly. Dynamic mechanical analysis revealed that, at elevated temperatures, improvement of mechanical properties due to the presence of nanofibers was even more noticeable. Addition of nanofibers resulted in increased thermal stability of PVA in thermogravimetric analysis due to the reduction in mobility of matrix molecules. Morphological observations showed no signs of agglomeration of fibers even in composites with high cellulose nanofiber contents. Inclusion of nanofibers was shown to increase the density of composites.

scholarly journals Thermomechanical Properties of KevlarTM Reinforced Benzoxazine-Urethane Alloys

2013 ◽  
Vol 13 (1) ◽  
pp. 11
Author(s):  
Rimdusit S Rimdusit S ◽  
Kasemsiri P. Kasemsiri P. ◽  
Okhawilai M. Okhawilai M.
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Loss Modulus ◽  
Flexural Modulus ◽  
Testing Machine ◽  
Impact Resistance ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Alloy Matrix ◽  
Wide Range

Ballistic armor is one of an important application which required high performance of fiber-reinforced polymer due to its outstanding specific mechanical properties. Therefore, KevlarTM reinforced benzoxazine-urethane alloys as ballistic impact resistance composites were developed in this research. The polybenzoxazine alloy composites were fabricated by compression molding at 200ºC and 5 MPa by a compression molder. The amount of urethane fraction in the alloy matrix was ranging from 0-40wt% while the fiber content was kept constant at 80wt%. The mechanical properties of the matrix alloys and their KevlarTM fiber composites were characterized by dynamic mechanical analysis and universal testing machine. The results revealed that storage modulus at room temperature of the composites was reduced from 16.82 GPa when using the neat polybenzoxazine as a matrix to the value of 11.89 GPa at 40wt% of urethane content in the alloy matrix. Moreover, the more urethane in the alloy matrix resulted in lower flexural modulus of the KevlarTM composites i.e. 22 GPa when using the neat polybenzoxazine as a matrix to the value of 12 GPa when using 40wt% of urethane in the alloy matrix. Interestingly, glass transition temperature (Tg) obtained from the maximum peak of the loss modulus was observed to be in the range of 187-247ºC, which was significantly higher than those of the two parent polymers. Furthermore, the activation energy of the alloys was found to increase with increasing urethane content, which corresponded to the observed Tg value enhancement. The observed synergism in Tg of KevlarTM reinforced benzoxazine-urethane was an outstanding characteristic for a wide range of applications, which requires high thermal stability.

Influence of filler loading on the mechanical and morphological properties of carbonized coconut shell particles reinforced polypropylene composites

2019 ◽  
Vol 54 (3) ◽  
pp. 397-407
Author(s):  
Uchechi C Mark ◽  
Innocent C Madufor ◽  
Henry C Obasi ◽  
Udochukwu Mark
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Filler Loading ◽  
Coconut Shell ◽  
Morphological Properties ◽  
Filler Materials ◽  
Shell Particles ◽  
Coconut Shells

The high cost of mineral-based fillers and their processing difficulties have necessitated the search for alternative and cheaper filler materials, usually agro-waste materials such as coconut shells. The coconut shells were carbonized, pulverized, and sieved into four particles sizes, namely; 63 μm, 150 μm, 300 μm, and 425 μm. The carbonized coconut shell particles of each particle size were used as fillers in the preparation of polypropylene-filled composites at filler loadings of 0, 10, 20, 30, and 40 wt. %. The control was the neat polypropylene of 0% filler addition. The polypropylene/carbonized coconut shell particles composites were prepared via melt blending of polypropylene and the filler in an injection molding machine to obtain composite sheets. The influence of filler loading on the mechanical properties was evaluated. The addition of fillers was found to improve the yield strength, tensile strength, tensile modulus, flexural strength, flexural modulus, and hardness of polypropylene as these mechanical properties increased with increase in filler loading. The elongation at break and modulus of resilience of the prepared polypropylene/carbonized coconut shell particles composites were, however, observed to decline with an increase in the filler loading. Compared with the neat polypropylene, the filler showed enhanced mechanical properties in the prepared composites. SEM revealed good filler–matrix interaction because of good interfacial adhesion. The incorporation of more filler resulted in the formation of more spherulite-producing nuclei, reduction of pore sizes, and enhanced particle size distribution with improved mechanical properties. Experimental data modeling showed the addition of more than 48% carbonized coconut shell particles to polypropylene would compromise property enhancement.

scholarly journals MODIFICATION OF EPOXY POLYMERS WITH THE USE OF NANOSIZED OF ALUMINIUM OXIDE

2017 ◽  
Vol 12 (5) ◽  
pp. 21-27 ◽  
Author(s):  
A. S. Mostovoi ◽  
A. A. Taganova ◽  
K. V. Prokopovich ◽  
E. V. Yakovleva
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Aluminium Oxide ◽  
Epoxy Oligomer ◽  
Curing Temperature ◽  
Epoxy Composites ◽  
Breaking Stress ◽  
Epoxy Composition

The aim of this work was to improve the physical, chemical and mechanical properties of epoxy composites with the use of nanosized aluminium oxide. The studies proved the possibility of directional control of the operational properties of epoxy composites by the use of small additions of nanosized aluminium oxide ensuring the creation of epoxy composites with high performance, satisfying the requirements of most industries. The rational content of aluminium oxide as a nanostructuring additive in an epoxy composition was selected (0,05 parts by weight). It ensures an increase in the complex of physico-mechanical properties (the breaking stress increases 3.3-fold, and the flexural modulus increases by 27%, the breaking stress in compression improves by 43%, the breaking stress and the tensile modulus of elasticity increases by 47-50%, the toughness increases 3-fold, and the hardness increases by 67%), while maintaining heat resistance. The introduction of nanosized aluminium oxide changes the parameters of the epoxy oligomer curing kinetics: the gelation duration increases from 45 to 75 minutes, and the duration of cure, from 53 to 100 minutes, while the maximum curing temperature is practically unchanged. Thus, the developed materials may be used for sealing electronic articles, for impregnating and filling components in aircraft engineering, shipbuilding and, automotive industry.

scholarly journals EFFECT OF HUMIDITY ON THE MECHANICAL PROPERTIES OF KENAF YARN FIBRE/POLYLACTIC ACID BIOCOMPOSITES

2019 ◽  
Vol 81 (5) ◽  
Author(s):  
Meor Syazalee ◽  
Rozli Zulkifli
Keyword(s):  
Mechanical Properties ◽  
Relative Humidity ◽  
Polylactic Acid ◽  
Mechanical Performance ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Mechanical Analysis ◽  
Natural Fibre ◽  
Static Mechanical ◽  
And Storage

Humidity during the fabrication of natural fibre reinforced composites can harm their mechanical performance. This study examines the effect of humidity during the fabrication of unidirectional kenaf/polylactic acid (PLA) biocomposites on their dynamic and static mechanical properties. Kenaf fibres were conditioned at different relative humidity (RH) levels (40% RH, 60% RH and 80% RH) before being pressed with PLA to form biocomposites. Kenaf/PLA biocomposites were analysed using dynamic mechanical analysis, fracture toughness in mode II, tensile and flexural. Results indicated that the value of GIIC and storage modulus decreased when the relative humidity increased. Reduced tensile and flexural modulus were observed when kenaf was exposed to high relative humidity of 80% RH. However, the form of unidirectional kenaf affected the properties and reduced the drop value in the tensile modulus. The optimum relative humidity to produce kenaf/PLA biocomposites is 40% RH.

Star-shaped arylacetylene resins derived from silicon

2020 ◽  
Vol 40 (8) ◽  
pp. 676-684
Author(s):  
Niping Dai ◽  
Junkun Tang ◽  
Manping Ma ◽  
Xiaotian Liu ◽  
Chuan Li ◽  
...  
Keyword(s):  
High Performance ◽  
Room Temperature ◽  
Mechanical Test ◽  
Flexural Modulus ◽  
Mechanical Analysis ◽  
Reinforced Composites ◽  
Scanning Calorimetry ◽  
Chemical Structures ◽  
Structures And Properties ◽  
High Performance Resin

AbstractStar-shaped arylacetylene resins, tris(3-ethynyl-phenylethynyl)methylsilane, tris(3-ethynyl-phenylethynyl) phenylsilane, and tris (3-ethynyl-phenylethynyl) silane (TEPHS), were synthesized through Grignard reaction between 1,3-diethynylbenzene and three types of trichlorinated silanes. The chemical structures and properties of the resins were characterized by means of nuclear magnetic resonance, fourier-transform infrared spectroscopy, Haake torque rheomoter, differential scanning calorimetry, dynamic mechanical analysis, mechanical test, and thermogravimetric analysis. The results show that the melt viscosity at 120 °C is lower than 150 mPa⋅s, and the processing windows are as wide as 60 °C for the resins. The resins cure at the temperature as low as 150 °C. The good processabilities make the resins to be suitable for resin transfer molding. The cured resins exhibit high flexural modulus and excellent heat-resistance. The flexural modulus of the cured TEPHS at room temperature arrives at as high as 10.9 GPa. Its temperature of 5% weight loss (Td5) is up to 697 °C in nitrogen. The resins show the potential for application in fiber-reinforced composites as high-performance resin in the field of aviation and aerospace.

scholarly journals Effect of SWCNT-Tuball Paper on the Lightning Strike Protection of CFRPs and Their Selected Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3140
Author(s):  
Kamil Dydek ◽  
Anna Boczkowska ◽  
Rafał Kozera ◽  
Paweł Durałek ◽  
Łukasz Sarniak ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Copper Foil ◽  
Impact Resistance ◽  
Mechanical Analysis ◽  
Lightning Strike ◽  
Single Wall Carbon Nanotubes ◽  
Carbon Fibre Reinforced Polymer ◽  
The Impact

The main aim of this work was the investigation of the possibility of replacing the heavy metallic meshes applied onto the composite structure in airplanes for lightning strike protection with a thin film of Tuball single-wall carbon nanotubes in the form of ultra-light, conductive paper. The Tuball paper studied contained 75 wt% or 90 wt% of carbon nanotubes and was applied on the top of carbon fibre reinforced polymer before fabrication of flat panels. First, the electrical conductivity, impact resistance and thermo-mechanical properties of modified laminates were measured and compared with the reference values. Then, flat panels with selected Tuball paper, expanded copper foil and reference panels were fabricated for lightning strike tests. The effectiveness of lightning strike protection was evaluated by using the ultrasonic phased-array technique. It was found that the introduction of Tuball paper on the laminates surface improved both the surface and the volume electrical conductivity by 8800% and 300%, respectively. The impact resistance was tested in two directions, perpendicular and parallel to the carbon fibres, and the values increased by 9.8% and 44%, respectively. The dynamic thermo-mechanical analysis showed higher stiffness and a slight increase in glass transition temperature of the modified laminates. Ultrasonic investigation after lightning strike tests showed that the effectiveness of Tuball paper is comparable to expanded copper foil.

scholarly journals Influence of Treated Distillate Aromatic Extract (TDAE) Content and Addition Time on Rubber-Filler Interactions in Silica Filled SBR/BR Blends

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 698
Author(s):  
Selin Sökmen ◽  
Katja Oßwald ◽  
Katrin Reincke ◽  
Sybill Ilisch
Keyword(s):  
Mechanical Properties ◽  
Oil Content ◽  
Tensile Modulus ◽  
Mechanical Analysis ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Binary Blends ◽  
Rubber Layer ◽  
Processing Aids ◽  
Rubber Filler

High compatibility and good rubber–filler interactions are required in order to obtain high quality products. Rubber–filler and filler–filler interactions can be influenced by various material factors, such as the presence of processing aids. Although different processing aids, especially the plasticizers, and their effects on compatibility have been investigated in the literature, their influence on rubber–filler interactions in highly active filler reinforced mixtures is not explicit and has not been investigated in depth. For this purpose, the influence of treated distillate aromatic extract (TDAE) oil content and its addition time on interactions between silica and rubber chains were investigated in this study. Rubber–filler and filler–filler interactions of uncured and cured silica-filled SBR/BR blends were characterized by using rubber layer L concept and dynamic mechanical analysis, whereas mechanical properties were studied by tensile test and Shore A hardness. Five parts per hundred rubber (phr) TDAE addition at 0, 1.5, and 3 min of mixing were characterized to investigate the influence of TDAE addition time on rubber–filler interactions. It was observed that addition time of TDAE can influence the development of bounded rubber structure and the interfacial interactions, especially at short time of mixing, less than 5 min. Oil addition with silica at 1.5 min of mixing resulted in fast rubber layer development and a small reduction in storage shear modulus of uncured blends. The influence of oil content on rubber–filler and filler–filler interactions were investigated for the binary blends without oil, with 5 and 20 phr TDAE content. The addition of 5 phr oil resulted in a slight increase in rubber layer and 0.05 MPa reduction in Payne effect of uncured blends. The storage tensile modulus of vulcanizates at small strains decreased from 13.97 to 8.28 MPa after oil addition. Twenty parts per hundred rubber (phr) oil addition to binary blends caused rubber layer L to decrease from 0.45 to 0.42. The storage tensile modulus of the vulcanizates and its reduction with higher amplitudes were incontrovertibly high among the vulcanizates with lower oil content, which were 13.57 and 4.49 MPa, respectively. When any consequential change in mechanical properties of styrene–butadiene rubber (SBR)/butadiene rubber (BR) blends could not be observed at different TDAE addition time, increasing amount of oil in blends enhanced elongation at break, and decreased Shore A hardness and tensile strength.

scholarly journals Mechanical and Morphological Properties of Bio-Phenolic/Epoxy Polymer Blends

Molecules ◽  
2021 ◽  
Vol 26 (4) ◽  
pp. 773
Author(s):  
Ahmad Safwan Ismail ◽  
Mohammad Jawaid ◽  
Norul Hisham Hamid ◽  
Ridwan Yahaya ◽  
Azman Hassan
Keyword(s):  
Mechanical Properties ◽  
Phase Separation ◽  
Polymer Blends ◽  
Epoxy Polymer ◽  
Flexural Modulus ◽  
Polymeric Materials ◽  
Morphological Properties ◽  
Comparison Results ◽  
Unique Material ◽  
Different Types

Polymer blends is a well-established and suitable method to produced new polymeric materials as compared to synthesis of a new polymer. The combination of two different types of polymers will produce a new and unique material, which has the attribute of both polymers. The aim of this work is to analyze mechanical and morphological properties of bio-phenolic/epoxy polymer blends to find the best formulation for future study. Bio-phenolic/epoxy polymer blends were fabricated using the hand lay-up method at different loading of bio-phenolic (5 wt%, 10 wt%, 15 wt%, 20 wt%, and 25 wt%) in the epoxy matrix whereas neat bio-phenolic and epoxy samples were also fabricated for comparison. Results indicated that mechanical properties were improved for bio-phenolic/epoxy polymer blends compared to neat epoxy and phenolic. In addition, there is no sign of phase separation in polymer blends. The highest tensile, flexural, and impact strength was shown by P-20(biophenolic-20 wt% and Epoxy-80 wt%) whereas P-25 (biophenolic-25 wt% and Epoxy-75 wt%) has the highest tensile and flexural modulus. Based on the finding, it is concluded that P-20 shows better overall mechanical properties among the polymer blends. Based on this finding, the bio-phenolic/epoxy blend with 20 wt% will be used for further study on flax-reinforced bio-phenolic/epoxy polymer blends.

Sign in / Sign up

Export Citation Format

Share Document