scholarly journals Controllable Synthesis of Mn3O4 Nanowires and Application in the Treatment of Phenol at Room Temperature

Nanomaterials ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 461 ◽  
Author(s):  
Runlin Han ◽  
Min Chen ◽  
Xiaobing Liu ◽  
Yuhang Zhang ◽  
Yongli Xie ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Hydrothermal Reaction ◽  
X Ray Diffraction ◽  
Acid Condition ◽  
Facile Hydrothermal Method ◽  
Phenol Solution ◽  
X Ray ◽  
Before And After ◽  
Phenol Treatment

Nanosized Mn3O4 nanowires are prepared with KMnO4 and ethanol in mild conditions by facile hydrothermal method. Hydrothermal reaction temperature is optimized to get uniform nanowires. The prepared Mn3O4 nanowires exhibit high activity in the treatment of phenol at acid condition and room temperature. The 20 mg Mn3O4 nanowires can efficiently dispose of 50 mL phenol solution (0.2 g·L−1) at pH 2 and 25 °C. The nanowires before and after phenol treatment are characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) and the reaction mechanism is discussed.

scholarly journals Synthesis of Magnetic Ferrocene-Containing Polymer with Photothermal Effects for Rapid Degradation of Methylene Blue

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 558
Author(s):  
Wenhui Zhu ◽  
Caiyun Zhang ◽  
Yali Chen ◽  
Qiliang Deng
Keyword(s):  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Degradation Rate ◽  
Model Compound ◽  
Vibrating Sample Magnetometer ◽  
Simulated Sunlight ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir

Photothermal materials are attracting more and more attention. In this research, we synthesized a ferrocene-containing polymer with magnetism and photothermal properties. The resulting polymer was characterized by Fourier-transform infrared (FT-IR), vibrating sample magnetometer (VSM), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Its photo-thermocatalytic activity was investigated by choosing methylene blue (MB) as a model compound. The degradation percent of MB under an irradiated 808 nm laser reaches 99.5% within 15 min, and the degradation rate is 0.5517 min−1, which is 145 times more than that of room temperature degradation. Under irradiation with simulated sunlight, the degradation rate is 0.0092 min−1, which is approximately 2.5 times more than that of room temperature degradation. The present study may open up a feasible route to degrade organic pollutants.

ROOM TEMPERATURE PHOTOLUMINESCENCE OF POLYCRYSTALLINE SIC PREPARED FROM CARBON-SATURATED SI MELT

2002 ◽  
Vol 16 (06n07) ◽  
pp. 1047-1051
Author(s):  
JIANPING MA ◽  
ZHIMING CHEN ◽  
GANG LU ◽  
MINGBIN YU ◽  
LIANMAO HANG ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Uv Light ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Composition And Structure ◽  
Light Excitation ◽  
Scanning Electron

Intense photoluminescence (PL) has been observed at room temperature from the polycrystalline SiC samples prepared from carbon-saturated Si melt at a temperature ranging from 1500 to 1650°C. Composition and structure of the samples have been confirmed by means of X-ray photoelectron spectroscopy, X-ray diffraction and scanning electron microscopy. PL measurements with 325 nm UV light excitation revealed that the room temperature PL spectrum of the samples consists of 3 luminescent bands, the peak energies of which are 2.38 eV, 2.77 eV and 3.06 eV, respectively. The 2.38 eV band is much stronger than the others. It is suggested that some extrinsic PL mechanisms associated with defect or interface states would be responsible to the intensive PL observed at room temperature.

Oxidation of Alloy-X in Subcritical, Transition, and Supercritical Water

CORROSION ◽  
10.5006/3881 ◽  
2021 ◽  
Author(s):  
Zachary Karmiol ◽  
Dev Chidambaram
Keyword(s):  
Supercritical Water ◽  
Photoelectron Spectroscopy ◽  
Focused Ion Beam ◽  
Elevated Temperatures ◽  
Subcritical Water ◽  
Ion Beam ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nickel Based Superalloy ◽  
Before And After

This work investigates the oxidation of a nickel based superalloy, namely Alloy X, in water at elevated temperatures: subcritical water at 261°C and 27 MPa, the transition between subcritical and supercritical water at 374°C and 27 MPa, and supercritical water at 380°C and 27 MPa for 100 hours. The morphology of the sample surfaces were studied using scanning electron microscopy coupled with focused ion beam milling, and the surface chemistry was investigated using X-ray diffraction, Raman spectroscopy, energy dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy before and after exposure studies. Surfaces of all samples were identified to comprise of a ferrite spinel containing aluminum.

Characterization of X-ray irradiated graphene oxide coatings using X-ray diffraction, X-ray photoelectron spectroscopy, and atomic force microscopy

2013 ◽  
Vol 28 (2) ◽  
pp. 68-71 ◽  
Author(s):  
Thomas N. Blanton ◽  
Debasis Majumdar
Keyword(s):  
Atomic Force Microscopy ◽  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
High Energy ◽  
X Ray Diffraction ◽  
Carbon Phase ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Before And After

In an effort to study an alternative approach to make graphene from graphene oxide (GO), exposure of GO to high-energy X-ray radiation has been performed. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) have been used to characterize GO before and after irradiation. Results indicate that GO exposed to high-energy radiation is converted to an amorphous carbon phase that is conductive.

A study of adsorption and absorption mechanisms of copper in palygorskite

Clay Minerals ◽  
2008 ◽  
Vol 43 (2) ◽  
pp. 195-203 ◽  
Author(s):  
Y. F. Cai ◽  
J. Y. Xue
Keyword(s):  
Photoelectron Spectroscopy ◽  
Esr Spectra ◽  
X Ray Diffraction ◽  
X Ray ◽  
Tetrahedral Sites ◽  
Octahedral Cation ◽  
Spin Resonance ◽  
Before And After ◽  
Cu Ions ◽  
Complex Ion

AbstractDesorption experiments performed on four Cu-adsorbed palygorskites suggest that the leached Cu2+ ion originates at the surface and/or net-like interstice of the palygorskite fibres. The leached fraction, calculated from the quantities of adsorbed Cu2+ before and after desorption, is <1%. This may indicate that the majority of Cu is in inaccessible structural sites. X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared (FTIR) spectroscopy and electron spin resonance (ESR) were used to determine the mineralogical character of the Cu-adsorbed palygorskite. Two photoelectron lines at 932.5 and/or 933.7 eV in the narrow scan Cu 2p3/2 spectra show that Cu adsorbed on the surface of palygorskite is in the Cu+ and Cu2+ state. The stretching vibrations of the octahedral cation shift ~3–5 cm–1 towards a greater wavenumber in the FTIR spectra of Cu-adsorbed palygorskite. It can be deduced that the Cu2+ is trapped in the channel of the palygorskite structure. The ESR spectra of the palygorskite give g values of 2.34, 2.12, 2.08 and 2.05, suggesting that some Cu ions cannot be reached by H+. These results confirm that Cu is adsorbed by palygorskite via three possible mechanisms: (1) the Cu is adsorbed onto the surface or in a net-like interstice, and its oxidation states are +1 and +2; (2) Cu forms a complex ion – [Cu(H2O)4]2+ or [Cu(H2O)6]2+, and is trapped in the channel; or (3) Cu enters into the hexagonal channel of the tetrahedral sites or the unoccupied octahedral sites of palygorskite.

X-Ray Diffraction Studies on the Titanium-Nickel System

1962 ◽  
Vol 6 ◽  
pp. 74-84
Author(s):  
John V. Gilfrich
Keyword(s):  
Heat Treatment ◽  
Room Temperature ◽  
Stoichiometric Composition ◽  
Physical Property ◽  
X Ray Diffraction ◽  
X Ray ◽  
Property Data ◽  
Before And After ◽  
Titanium Nickel ◽  
Physical Property Data

AbstractX-ray diffraction studies were made on the Ti–Ni system around the stoichiometric composition of the intermetallic compound TiNi to clarify some confusion which has existed about the phase diagram in this region, and to explain some anomalies in the physical properties of this material. Wrought and cast samples were examined at room temperature both before and after heat treatment and at temperatures both above and below ambient. The compound TiNi does exist at room temperature. The phase purity of the particular sample was found to be greatly affected by such factors as minor variations in composition, heat treatment, and method of sample preparation. Some confirming metallographlc and physical property data will also be presented.

Hydrothermal Synthesis and Photocatalytic Properties of Flower-Like CdS Nanostructures

2011 ◽  
Vol 335-336 ◽  
pp. 460-463 ◽  
Author(s):  
Hong Mei Wang ◽  
Da Peng Zhou ◽  
Yuan Lian ◽  
Ming Pang ◽  
Dan Liu
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Uv Light ◽  
Sulfur Source ◽  
X Ray Diffraction ◽  
Facile Hydrothermal Method ◽  
X Ray ◽  
Transmission Electron ◽  
Cds Nanostructures

Hexagonal flower-like CdS nanostructures were successfully synthesized through a facile hydrothermal method with thiourea as sulfur source. By combining the results of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), the structural and morphological characterizations of the products were performed. The photocatalytic activity of CdS nanostructures had been tested by degradation of Rhodamine B (RB) under UV light compared to commercial CdS powders, which indicated that the as-syntherized CdS nanostructures exhibited enhanced photocatalytic activity for degradation of RB. The possible growth mechanism of CdS nanostructures was proposed in the end.

XRD and XPS studies of room temperature spontaneous interfacial reaction of CeO2 thin films on Si and Si3N4 substrates

RSC Advances ◽  
2014 ◽  
Vol 4 (108) ◽  
pp. 62935-62939 ◽  
Author(s):  
Parthasarathi Bera ◽  
Chinnasamy Anandan
Keyword(s):  
Thin Films ◽  
Interfacial Reaction ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Interfacial Reactions ◽  
X Ray Diffraction ◽  
X Ray

X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) investigations of interfacial reactions between Ce and Si have been carried out on as-deposited and 15 month aged CeO2/Si and CeO2/Si3N4 thin films.

scholarly journals Room-Temperature Formation of Hard BCx Films by Low Power Magnetron Sputtering

2021 ◽  
Vol 11 (21) ◽  
pp. 9896
Author(s):  
Veronica Sulyaeva ◽  
Maxim Khomyakov ◽  
Marina Kosinova
Keyword(s):  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
Film Properties ◽  
X Ray ◽  
Sputtering Power ◽  
Chemical States ◽  
Rf Signal ◽  
Dual Target

Boron carbide is one of the most important non-metallic materials. Amorphous BCx films were synthesized at room temperature by single- and dual-target magnetron sputtering processes. A B4C target and C target were operated using an RF signal and a DC signal, respectively. The effect of using single- and dual-target deposition and process parameters on the chemical bonding and composition of the films as well as their functional properties were characterized by Fourier transform infrared spectroscopy, Raman spectroscopy, X-ray photoelectron spectroscopy, X-ray energy dispersive analysis, X-ray diffraction, ellipsometry, and spectrophotometry. It was found that the film properties depend on the sputtering power and the used targets. EDX data show that the composition of the samples varied from B2C to practically BC2 in the case of using an additional C target. According to the XPS data, it corresponds to the different chemical states of the boron atom. A nanoindentation study showed that the film with a composition close to B2C deposited with the highest B4C target power reached a hardness of 25 GPa and Young’s modulus of 230 GPa. The optical properties of the films also depend on the composition, so the band gap (Eg) of the BCx film varied in the range of 2.1–2.8 eV, while the Eg of the carbon-rich films decreased to 1.1 eV.

scholarly journals Fabrication of Mo-Doped WO3 Nanorod Arrays on FTO Substrate with Enhanced Electrochromic Properties

Materials ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 1627 ◽  
Author(s):  
Bao Wang ◽  
Wenkuan Man ◽  
Haiyang Yu ◽  
Yang Li ◽  
Feng Zheng
Keyword(s):  
Photoelectron Spectroscopy ◽  
Response Times ◽  
Hydrothermal Reaction ◽  
Average Diameter ◽  
Nanorod Arrays ◽  
X Ray Diffraction ◽  
Hydrothermal Temperature ◽  
X Ray ◽  
Electrochromic Properties ◽  
Wo3 Nanorod

Well-oriented and crystalline WO3 nanorod arrays (WNRAs) decorated with Mo were synthesized on fluorine doped tin oxide (FTO) substrate by the hydrothermal method. The effects of Mo doping, hydrothermal reaction time, and hydrothermal temperature on the morphologies and electrochromic properties of as-prepared WNRAs were studied thoroughly. Scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and chronoamperometry techniques were used to characterize the structures and properties of obtained WNRAs. The results demonstrate that the average diameter of the as-prepared WNRAs ranged from 30 to 70 nm. During the decoration of Mo on the WNRAs, the growth density of as-prepared WNRAs decreased and the surfaces became rough. However, the decorated Mo on WNRAs synthesized at 180 °C for 5 h with a Mo/W mole ratio of 1:40 exhibited better electrochromic properties than single WNRAs. They exhibited high optical modulation (61.7%), fast bleaching/coloring response times (3 s/9 s), high coloration efficiency values (73.1 cm2/C), and good cycling stability.

Sign in / Sign up

Export Citation Format

Share Document