scholarly journals Morphology, Rheological and Mechanical Properties of Isotropic and Anisotropic PP/rPET/GnP Nanocomposite Samples

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 3058
Author(s):  
Francesco Paolo La Mantia ◽  
Vincenzo Titone ◽  
Alessandro Milazzo ◽  
Manuela Ceraulo ◽  
Luigi Botta
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Morphological Analysis ◽  
Capillary Viscometer ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Recycled Polyethylene ◽  
Fibrillar Morphology ◽  
High Deformability ◽  
Poor Adhesion

The effect of graphene nanoplatelets (GnPs) on the morphology, rheological, and mechanical properties of isotropic and anisotropic polypropylene (PP)/recycled polyethylene terephthalate (rPET)-based nanocomposite are reported. All the samples were prepared by melt mixing. PP/rPET and PP/rPET/GnP isotropic sheets were prepared by compression molding, whereas the anisotropic fibers were spun using a drawing module of a capillary viscometer. The results obtained showed that the viscosity of the blend is reduced by the presence of GnP due to the lubricating effect of the graphene platelets. However, the Cox–Merz rule is not respected. Compared to the PP/rPET blend, the GnP led to a slight increase in the elastic modulus. However, it causes a slight decrease in elongation at break. Morphological analysis revealed a poor adhesion between the PP and PET phases. Moreover, GnPs distribute around the droplets of the PET phase with a honey-like appearance. Finally, the effect of the orientation on both systems gives rise not only to fibers with higher modulus values, but also with high deformability and a fibrillar morphology of the dispersed PET phase. A fragile-ductile transition driven by the orientation was observed in both systems.

Graphite/Bio-Based Epoxy Composites: The Mechanical Properties Interface

2015 ◽  
Vol 799-800 ◽  
pp. 115-119 ◽  
Author(s):  
Anika Zafiah M. Rus ◽  
Nur Munirah Abdullah ◽  
M.F.L. Abdullah ◽  
M. Izzul Faiz Idris
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Filler Content ◽  
Weight Percent ◽  
Epoxy Composites ◽  
Elongation At Break ◽  
Graphite Content ◽  
Dispersion Condition ◽  
Strong Interfacial Bonding

Graphite reinforced bio-based epoxy composites with different particulate fractions of graphite were investigated for mechanical properties such as tensile strength, elastic modulus and elongation at break. The graphite content was varied from 5 wt.%, 10 wt.%, 15 wt.%, 20 wt.%, 25 wt.%, 30 wt.% by weight percent in the composites. The results showed that the mechanical properties of the composites mainly depend on dispersion condition of the treated graphite filler, aggregate structure and strong interfacial bonding between treated graphite in the bio-based epoxy matrix. The composites showed improved tensile strength and elastic modulus with increase treated graphite weight loading. This also revealed the composites with increasing filler content was decreasing the elongation at break.

scholarly journals Structure and Properties of Polyoxymethylene/Silver/Maleic Anhydride-Grafted Polyolefin Elastomer Ternary Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1954
Author(s):  
Yang Liu ◽  
Xun Zhang ◽  
Quanxin Gao ◽  
Hongliang Huang ◽  
Yongli Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Maleic Anhydride ◽  
Ag Nanoparticles ◽  
Decomposition Temperature ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Maximum Value ◽  
Polyolefin Elastomer ◽  
Local Defects

In the present study, silver (Ag) nanoparticles and maleic anhydride-grafted polyolefin elastomer (MAH-g-POE) were used as enhancement additives to improve the performance of the polyoxymethylene (POM) homopolymer. Specifically, the POM/Ag/MAH-g-POE ternary nanocomposites with varying Ag nanoparticles and MAH-g-POE contents were prepared by a melt mixing method. The effects of the additives on the microstructure, thermal stability, crystallization behavior, mechanical properties, and dynamic mechanical thermal properties of the ternary nanocomposites were studied. It was found that the MAH-g-POE played a role in the bridging of the Ag nanoparticles and POM matrix and improved the interfacial adhesion between the Ag nanoparticles and POM matrix, owing to the good compatibility between Ag/MAH-g-POE and the POM matrix. Moreover, it was found that the combined addition of Ag nanoparticles and MAH-g-POE significantly enhanced the thermal stability, crystallization properties, and mechanical properties of the POM/Ag/MAH-g-POE ternary nanocomposites. When the Ag/MAH-g-POE content was 1 wt.%, the tensile strength reached the maximum value of 54.78 MPa. In addition, when the Ag/MAH-g-POE content increased to 15wt.%, the elongation at break reached the maximum value of 64.02%. However, when the Ag/MAH-g-POE content further increased to 20 wt.%, the elongation at break decreased again, which could be attributed to the aggregation of excessive Ag nanoparticles forming local defects in the POM/Ag/MAH-g-POE ternary nanocomposites. Furthermore, when the Ag/MAH-g-POE content was 20 wt.%, the maximum decomposition temperature of POM/Ag/MAH-g-POE ternary nanocomposites was 398.22 °C, which was 71.39 °C higher than that of pure POM. However, compared with POM, the storage modulus of POM/Ag/MAH-g-POE ternary nanocomposites decreased with the Ag/MAH-g-POE content, because the MAH-g-POE elastomer could reduce the rigidity of POM.

Anisotropic Mechanical Properties of Rapid Prototyping Parts Fabricated by Stereolithography

2021 ◽  
Vol 13 (9) ◽  
pp. 1812-1819
Author(s):  
Na-Na Yang ◽  
Hao-Rui Liu ◽  
Ning Mi ◽  
Qi Zhou ◽  
Li-Qun He ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Brittle Fracture ◽  
Fracture Surface ◽  
Elongation At Break ◽  
Build Orientation ◽  
Range Distribution ◽  
Anisotropic Mechanical Properties ◽  
Orientation Experiment

Stereolithography (SLA)-manufactured parts behave with anisotropic properties due to the varying interface orientations generated by the layer-based manufacturing process. Part build orientation is a very important factor of anisotropic mechanical properties. In this paper, the build orientation experiment was designed to study the anisotropic behaviour of the mechanical properties of the SLA parts based on the orientation relationship between the force and the layer. The results show that there are obvious brittle characteristics on the fracture surface of the specimens and microcracks perpendicular to the direction of the layer distributed on the side of the fracture. The mechanical properties under brittle fracture have different degrees of sensitivity to the build orientation. Among all the build orientations, whether a specimen is built flat or on an edge shows obvious difference in tensile strength, and the relative range distribution reaches 35%. The changes in elastic modulus and the elongation at break are the most obvious in different angles relative to the XY plane, and the relative range distribution reaches 62% and 56% respectively. In all the build orientations designed, the tensile strength is the largest when it is placed on the edge at 0° with Y-axis in the XY plane, the elastic modulus is the largest when it was placed vertically, and the elongation at break is the largest when it is placed flat at 45° with Y-axis in the XY plane.

Compatibilization of natural rubber–polypropylene thermoplastic elastomer blend

2019 ◽  
Vol 52 (8) ◽  
pp. 728-746 ◽  
Author(s):  
Abderrahmane Belhaoues ◽  
Samia Benmesli ◽  
Farid Riahi
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Morphological Analysis ◽  
Thermoplastic Elastomer ◽  
Homogeneous Distribution ◽  
Molten State ◽  
Rotor Speed ◽  
Elongation At Break ◽  
Compatibilizing Agent ◽  
Elastomer Blend

The effects of the addition of epoxidized natural rubber/maleic anhydride-grafted polypropylene blend as a compatibilizing agent (CA) on the properties of natural rubber (NR)/polypropylene (PP) thermoplastic elastomer blend were studied. The blends were prepared in the molten state at 180°C using a Brabender Plasticorder at a rotor speed of 60 r min−1. Evidence of compatibilization was obtained from the Brabender plastograms and from the mechanical properties results as well as the morphological analysis. It was found that the addition of the CA at different contents resulted in an increase of the tensile strength and Young’s modulus and a decrease of the elongation at break. It was also found that the melting temperature remained unchanged, the % crystallinity decreased, but the thermal stability was not affected. The morphology revealed a more homogeneous distribution of the dispersed PP phase for the CA-containing systems compared to the control NR/PP blend. These effects were attributed to the interactions that developed with the blend constituents through the functional groups of the CA.

Prediction of mechanical properties of quaternary nanocomposites based on polypropylene using fuzzy logic

2020 ◽  
pp. 009524431989728
Author(s):  
Sajjad Daneshpayeh ◽  
Faramarz Ashenai Ghasemi ◽  
Shahnoosh Masoumi ◽  
Meysam Nouri Niyaraki
Keyword(s):  
Mechanical Properties ◽  
Fuzzy Logic ◽  
Elastic Modulus ◽  
Impact Strength ◽  
Considerable Increase ◽  
Graphene Nanosheets ◽  
Main Role ◽  
Elongation At Break ◽  
Prediction Of Mechanical Properties ◽  
Different Levels

The goal of the present study is to investigate and predict the mechanical properties, including impact strength, elastic modulus, and elongation-at-break of quaternary nanocomposites based on polypropylene (PP)/ethylene–propylene–diene monomer (EPDM)/glass fiber (GL)/graphene nanosheets (GPn) by fuzzy logic. Three parameters in different levels, including EPDM, GL, and GPn, were chosen for combination with a PP matrix. The fuzzy logic surfaces showed that the EPDM rubber and GPn had the main role in the elastic modulus of nanocomposites. The high levels of EPDM content resulted in a considerable increase in impact strength and, generally, the presence of EPDM had no effect on elongation-at-break.

Mechanical and Morphological Behavior of Blends Obtained from Biopolymers (PLA/PLC)

2014 ◽  
Vol 775-776 ◽  
pp. 24-28
Author(s):  
Taciana Regina de Gouveia Silva ◽  
Bartira Brandão da Cunha ◽  
Pankaj Agrawal ◽  
Edcleide Maria Araújo ◽  
Tomás Jefférson Alves de Mélo
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Elastic Modulus ◽  
Impact Strength ◽  
Polymer Blends ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Morphology Analysis ◽  
Morphological Behavior

In this work, the effect of the PCL content and E-GMA compatibilizer on the mechanical properties and morphology of poly (lactic acid) - PLA/ poly (ε-caprolactone)-PCL blends was investigated. The results of the mechanical properties showed that there was a reduction in the elastic modulus and tensile strength when PCL was added to PLA. The decrease in the modulus was more pronounced when the PCL content was increased from 10 to 20% (wt). The PLA/PCL/E-GMA blend showed the lower modulus and tensile strength. This blend also presented the higher elongation at break and impact strength. The morphology analysis by SEM showed that the PLA/PCL blends where characterized by lack of adhesion between the PLA and PCL phases. The presence of E-GMA in the PLA/PCL/E-GMA blend improved the adhesion between the PLA and PCL phases.Keywords: poly (latic acid); poly (ε-caprolactone); polymer blends; compatibilizer

Influence of Epoxide Levels in Epoxidized Natural Rubber (ENR) Molecules on Cure Characteristics, Dynamic Properties and Mechanical Properties of ENR/Montmorillonite Clay Nanocomposites

2013 ◽  
Vol 844 ◽  
pp. 247-250
Author(s):  
Piriyapol Yokkhun ◽  
Bencha Thongnuanchan ◽  
Charoen Nakason
Keyword(s):  
Mechanical Properties ◽  
Dynamic Properties ◽  
Montmorillonite Clay ◽  
Layered Silicates ◽  
Clay Nanocomposites ◽  
X Ray Diffraction ◽  
Melt Mixing ◽  
Maximum Torque ◽  
Elongation At Break ◽  
Cure Characteristics

Nanocomposites based on epoxidized natural rubbers (ENRs) with various levels of epoxide groups (i.e., 10, 20, 30, 40 and 50 mol%) and organoclay were prepared by melt mixing process. The organoclay employed in this study was montmorillonite clay modified by octadecylamine (OC-MMT). Cure characteristics, dynamic properties and mechanical properties of ENRs nanocomposites filled with 5 phr of OC-MMT were studied. In all cases, X-ray diffraction results indicated intercalation of ENRs into the silicate interlayer as an increase in the interlayer distance of layered silicates was observed. The maximum torque and torque difference of ENRs nanocomposites increased with increasing levels of epoxide groups in ENRs. Additionally, it was also found that the tan δ value at Tg of the ENR-50 nanocomposite was much lower than those of other types of ENRs nanocomposite. This indicates stronger interaction between ENR-50 and OC-MMT. However, ENR-50 nanocomposite showed the poorest elasticity in term of the tan δ value at the ambient temperature compared to other types of ENRs nanocomposites. A good balance between strength and elasticity was also observed in the ENR-30 nanocomposite. These results are also consistent with the observation that tensile strength and elongation at break of ENR-30 nanocomposite were higher than those of other types of ENRs nanocomposites.

scholarly journals LMPP Effects on Morphology, Crystallization, Thermal and Mechanical Properties of iPP/LMPP Blend Fibres

2018 ◽  
Vol 26 (2(128)) ◽  
pp. 26-31 ◽  
Author(s):  
Munir Hussain ◽  
Feichao Zhu ◽  
Feichao Zhu ◽  
Bin Yu ◽  
Bin Yu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Elastic Modulus ◽  
Isotactic Polypropylene ◽  
Degree Of Crystallinity ◽  
Thermal And Mechanical Properties ◽  
Elongation At Break ◽  
Breaking Elongation ◽  
Low Modulus ◽  
The Degree Of Crystallinity

The thermal properties and morphological characterisation of isotactic polypropylene (iPP) homopolymer and its blends with low molecular low modulus polypropylene (LMPP) were studied. Firstly blends were prepared with variant LMPP contents, and their properties were characterised using SEM, DSC, XRD, and DMA. Later the mechanical properties of iPP/LMPP blend fibres were investigated. SEM results showed that the iPP/LMPP blends produced smoother surfaces when the LMPP content was increased, as well as the miscibility. All the Tg values with different LMPP percentages were in-between pure iPP and LMPP. The XRD results indicated the LMPP percentage decreased along with the degree of crystallinity of the iPP/LMPP blends (5% to 15%), which increased and then decreased as compared to pure iPP. The elongation at break increased when the LMPP content increased, with the maximum breaking elongation of the LMPP 25% blend reaching 12.95%, which showed great stretch-ability, whereas the elastic modulus of iPP/LMPP blends decreased.

scholarly journals STUDY ON SOME PROPERTIES AND MORPHOLOGY OF COMPOSITES BASED ON POLYETHYLENE GRAFTED ACRYLIC ACID/ETHYLENE-VINYL ACETATE COPOLYMER/CALCIUM CARBONATE

2017 ◽  
Vol 25 (2) ◽  
pp. 355-361
Author(s):  
Thai Hoang ◽  
Do Van Cong
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Calcium Carbonate ◽  
Acrylic Acid ◽  
Ethylene Vinyl Acetate ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Acetate Copolymer ◽  
Ethylene Vinyl Acetate Copolymer ◽  
Better Than

Composites based on polyethylene grafted acrylic acid (PE-g-AAc)/ethylene-co-vinylacetate copolymer (EVA)/calcium carbonate (CaCO3) were prepared by melt mixing. Relative melt viscosity, morphology, mechanical properties and thermostability of the composites were studied. The experimental results show that the presence of (CaCO3) activated by stearic acid (10-20 wt.%) changes lightly stable torque of polymer blend of PE-g-AAc/EVA. Use of modified PE improves compatibility of PE and EVA as well as makes the components disperse into each other better than in blends using unmodified PE. Tensile strength and elongation at break of both polymer blends decrease with presence of CaCO3. However, tensile strength of the composites of PE-g-AAc/EVA/CaCO3 is higher than that of composites of PE/EVA/CaCO3. Beside that, the composites of PE-g-AAc/EVA/CaCO3 have thermostability higher than the composites of PE/EVA/CaCO3.  

Morphology and Mechanical Properties of LDPE, EVA and Fly Ash Composites

2020 ◽  
Vol 869 ◽  
pp. 76-81
Author(s):  
Vu Minh Trong ◽  
Bui Dinh Hoan
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Ethylene Vinyl Acetate ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Melt Mixing ◽  
Elongation At Break ◽  
Acetate Copolymer ◽  
Ethylene Vinyl Acetate Copolymer ◽  
Morphology And Mechanical Properties

The fly ash from Pha Lai power plant was modified by vinyltrimetoxysilan (VTMS). The polymer composites based on low-density polyethylene (LDPE), ethylene vinyl acetate copolymer (EVA) and fly ash (FA) without and with vinyltrimetoxysilan (VTMS) modification were prepared by melt mixing in a Haake Rheomixer. The tensile strength and elongation at break of the LDPE/EVA/VFA composites were also higher than those of the LDPE/EVA/FA composites. The FESEM images proved that FA-VTMS particles disperse more regularly in the polymer matrix in comparison with FA without VTMS modification. In addition, the surface modification of the FA reduced the size of agglomeration of FA particles.

Sign in / Sign up

Export Citation Format

Share Document