scholarly journals Study on the Properties of Transparent Bamboo Prepared by Epoxy Resin Impregnation

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 863 ◽  
Author(s):  
Yan Wu ◽  
Yajing Wang ◽  
Feng Yang ◽  
Jing Wang ◽  
Xuehua Wang
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Visible Light ◽  
Epoxy Resin ◽  
Raw Materials ◽  
Light Transmittance ◽  
Advantages And Disadvantages ◽  
Heat Treated ◽  
Before And After ◽  
Different Parts

In this paper, Moso bamboo (Phyllostachys heterocycle) before and after heat treatment were used as raw materials to prepare transparent bamboo (TB). In an acidic environment, the lignin contained in the bamboo material was removed to obtain a bamboo template, and an epoxy resin similar to the cellulose refractive index was used for vacuum impregnation into the bamboo template to obtain a transparent bamboo material. The purpose of this study was to compare the physical and chemical properties of TB and original bamboo and the differences between TBs before and after heat treatment, taken from different parts of bamboo, in order to explore the performance advantages and disadvantages of TB as a new material. The Fourier transform infrared spectroscopy analysis (FTIR), scanning electron microscope testing (SEM), three elements analysis, light transmittance testing, and mechanical strength testing were used to study the molecular composition, microstructure, chemical composition, light transmittance, and tensile strength of the TB samples. The results showed that the lignin content of the delignified bamboo templates was greatly reduced. In addition, the SEM images showed that a large amount of epoxy resin (type E51 and type B210 curing agent) was covered on the cross-section surface and pores of the TB samples. The FTIR showed that the epoxy molecular groups appeared on the TB, and the delignified bamboo template and the resin had a good synergy effect. According to the light transmittance testing, the original bamboo samples hardly contained light transmittance under visible light. The transmittance of transparent inner bamboo (TIB) and transparent heat-treated inner bamboo (THIB) could reach about 11%, and the transmittance of transparent outer bamboo (TOB) and transparent heat-treated outer bamboo (THOB) was about 2%. The light transmittance had been significantly improved when compared with the original bamboo samples. The transmittances of the TB samples before and after heat treatment in different parts of bamboo were different. In the visible light irradiation range, the light transmittances of TB samples were as follows: TIB > THIB and THOB > TOB. Meanwhile, the tensile strength of TB was reduced, especially for TOB and THOB. In addition, TB has a wide range of raw materials, and the preparation process is environmentally friendly. It can be used for decorative materials in homes, buildings, etc., and has a great application potential.

Failure analysis of heat treated HSLA wheel bolt steels

2010 ◽  
Vol 6 (3) ◽  
pp. 373-382
Author(s):  
Ali Nazari ◽  
Shadi Riahi
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Failure Analysis ◽  
Heat Treating ◽  
Boron Steel ◽  
Content Type ◽  
Heat Treated ◽  
Before And After ◽  
Molybdenum Steel ◽  
Optimum Heat

PurposeThe aims of this study is to analyze failure of two types of high‐strength low‐alloy (HSLA) steels which are used in wheel bolts 10.9 grade, boron steel and chromium‐molybdenum steel, before and after heat treatment.Design/methodology/approachThe optimum heat treatment to obtain the best tensile behavior was determined and Charpy impact and Rockwell hardness tests were performed on the two steel types before and after the optimum heat treating.FindingsFractographic studies show a ductile fracture for heat‐treated boron steel while indicate a semi‐brittle fracture for heat‐treated chromium‐molybdenum steel. Formation of a small boron carbide amount during heat treating of boron steel results in increment the bolt's tensile strength while the ductility did not changed significantly. In the other hand, formation of chromium and molybdenum carbides during heat treating of chromium‐molybdenum steel increased the bolt's tensile strength with a considerable reduction in the final ductility.Originality/valueThis paper evaluates failure analysis of HSLA wheel bolt steels and compares their microstructure before and after the loading regime.

scholarly journals Tension mechanical properties of recycled glass-epoxy composite material

2012 ◽  
pp. 189-198 ◽  
Author(s):  
Jelena Petrovic ◽  
Darko Ljubic ◽  
Marina Stamenovic ◽  
Ivana Dimic ◽  
Slavisa Putic
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
Composite Materials ◽  
Modulus Of Elasticity ◽  
Epoxy Composite ◽  
Raw Materials ◽  
Mechanical Tests ◽  
Recycled Glass ◽  
Before And After

The significance of composite materials and their applications are mainly due to their good properties. This imposes the need for their recycling, thus extending their lifetime. Once used composite material will be disposed as a waste at the end of it service life. After recycling, this kind of waste can be used as raw materials for the production of same material, which raises their applicability. This indicates a great importance of recycling as a method of the renowal of composite materials. This study represents a contribution to the field of mechanical properties of the recycled composite materials. The tension mechanical properties (tensile strength and modulus of elasticity) of once used and disposed glass-epoxy composite material were compared before and after the recycling. The obtained results from mechanical tests confirmed that the applied recycling method was suitable for glass-epoxy composite materials. In respect to the tensile strength and modulus of elasticity it can be further assessed the possibility of use of recycled glass-epoxy composite materials.

scholarly journals Alternative foaming agents for fabrication of glass foam

2021 ◽  
Vol 11 (5) ◽  
pp. 39-48
Author(s):  
Ildikó Fóris ◽  
Gábor Mucsi
Keyword(s):  
Raw Materials ◽  
Powder Mixtures ◽  
Foaming Agent ◽  
Foaming Agents ◽  
Heat Treated ◽  
Specimen Density ◽  
Before And After ◽  
Different Temperatures ◽  
Glass Foam ◽  
Eggshell Waste

Glass foam tablets were produced from container glass bottles (CGB) using eggshell waste (ESW) and perlite (P) as foaming agent in different portions. The ground raw materials (CGB, ESW, P) were homogenized and pressed with hydraulic piston press machine at different pressures (in the case of P containing tablets 30 MPa and ESW containing tablets 15 MPa, 30 MPa and 40 MPa were used).The obtained glass tablets were heat treated at different temperatures (in the case of P containing tablets 800 °C, 900°C, 1000°C and 1100°C, and ESW containing tablets 600 °C, 700 °C, 800 °C and 900 °C were used). The study shows the specimen density of tablets before and after heat treatment, as well as the true density of the powder mixtures before tableting and the abrasion resistance of the glass foam products.

scholarly journals Preparation and Assessment of Heat-Treated α-Chitin Nanowhiskers Reinforced Poly(viny alcohol) Film for Packaging Application

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1883 ◽  
Author(s):  
Chao Peng ◽  
Guangxue Chen
Keyword(s):  
Heat Treatment ◽  
Composite Films ◽  
Barrier Properties ◽  
Mechanical Tests ◽  
Light Transmittance ◽  
Poly Vinyl Alcohol ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Chitin Nanowhiskers

In this study, poly(vinyl alcohol) (PVA) composite films enhanced by α-chitin nanowhiskers (ChWs) were prepared through heat treatment. The obtained membranes were assessed by means of FTIR spectroscopy, X-ray diffraction, thermogravimetric analysis, regular light transmittance, mechanical tests, permeability and water absorption. The influence of the nano-component and heat treatment on the mechanical, thermal and water-resistant properties of the composite membrane were analyzed. From the results of the work, the produced films with excellent barrier properties and inexpensive raw processed materials have great prospects in packaging applications.

scholarly journals Enhanced visible-light photocatalytic activity of anatase-rutile mixed-phase nano-size powder given by high-temperature heat treatment

2020 ◽  
Vol 7 (1) ◽  
pp. 191539 ◽  
Author(s):  
Takamasa Ishigaki ◽  
Yusuke Nakada ◽  
Naoki Tarutani ◽  
Tetsuo Uchikoshi ◽  
Yoshihiro Tsujimoto ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Photocatalytic Activity ◽  
High Temperature ◽  
Visible Light ◽  
Photocatalytic Performance ◽  
High Temperature Heat Treatment ◽  
Heat Treated ◽  
Temperature Heating ◽  
Nano Size ◽  
Visible Light Photocatalytic

Nano-size EVONIK AEROXIDE ® P25 titanium dioxide, TiO 2 , powder was heat-treated at temperatures, 700–900°C, in air. An X-ray diffraction study showed that the P25 powder is composed of approximately 20 and approximately 80 mass% of rutile and anatase phases, respectively. It was also shown that the transformation from anatase to rutile induced by high-temperature heat treatment was almost completed at 750°C, whereas a small amount (less than 3 mass%) of anatase phase was still left even in the powder heat-treated at 900°C. The transformation behaviour was consistent with results obtained by Raman scattering spectroscopy. Raman experiments also indicated that high-temperature heating induced the formation of oxide ion vacancies. Powders were dispersed in methyl orange (MO) aqueous solution, and the bleach rate of MO was measured to evaluate photocatalytic activity under ultraviolet (UV)- and visible-light irradiation. After the heat treatment, the UV-light photocatalytic performance sharply deteriorated. Interestingly, visible-light photocatalytic activity was enhanced by high-temperature heating and reached the highest performance for an 800°C-heated sample, indicating that the P25 powder obtained high visible-light photocatalytic performance after heat treatment. Even after 900°C heat treatment, the photocatalytic performance was higher than that of as-received powder. Enhancement of photocatalytic activities was discussed in relation to visible light absorption and charge carrier transfer.

Microstructure and Mechanical Properties of TiB2/ Al-Si Composites Fabricated by TIG Wire and Arc Additive Manufacturing

2019 ◽  
Vol 944 ◽  
pp. 64-72
Author(s):  
Qing Feng Yang ◽  
Cun Juan Xia ◽  
Ya Qi Deng
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Yield Strength ◽  
Filler Wire ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Before And After

Bulky sample was made by using TIG wire and arc additive manufacturing (WAAM) technology, in which Ф1.6 mm filler wire of in-situ TiB2/Al-Si composites was selected as deposition metal, following by T6 heat treatment. The microstructure and mechanical properties of the bulky sample before and after heat treatment were analyzed. Experimental results showed that the texture of the original samples parallel to the weld direction and perpendicular to the weld direction was similar consisting of columnar dendrites and equiaxed crystals. After T6 heat treatment, the hardness of the sample was increased to 115.85 HV from 62.83 HV, the yield strength of the sample was 273.33 MPa, the average tensile strength was 347.33 MPa, and the average elongation after fracture was 7.96%. Although pore defects existed in the fracture, yet the fracture of the sample was ductile fracture.

Crack Detection in Aircraft Structures

1956 ◽  
Vol 60 (551) ◽  
pp. 739-748 ◽  
Author(s):  
W. Deck
Keyword(s):  
Heat Treatment ◽  
Sheet Metal ◽  
Crack Detection ◽  
Raw Materials ◽  
Aircraft Maintenance ◽  
Aircraft Structures ◽  
Heat Treated

In Switzerland aircraft often have to take off and land in narrow mountain valleys where a strong, irregular wind is blowing. In these circumstances one faulty casting may cause failure of a control; or a small part, if insufficiently heat-treated, may fracture and result in the loss of the aircraft. For this reason, thorough inspection during production and careful maintenance of the aircraft are of prime importance. Control within the aircraft factory consists of inspection of the raw materials, such as bars, sheet metal, tubes, castings, forgings and so on; testing of the most important parts during manufacture to detect cracks and to control the heat treatment; and the final control of all parts, of components and of the whole aircraft. Maintenance inspection reveals cracks, corrosion and other defects of the most important parts of the aircraft.

Effect of Heat Treatment on Tensile Strength and Microstructure of AZ61A Magnesium Alloy

2014 ◽  
Vol 606 ◽  
pp. 55-59 ◽  
Author(s):  
R. Senthil ◽  
A. Gnanavelbabu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Magnesium Alloys ◽  
Mg Alloys ◽  
Forming Process ◽  
Microstructural Parameters ◽  
Heat Treated ◽  
Mutual Relations

Magnesium alloys are the very progressive materials whereon is due to improve their end-use properties. Especially, wrought Mg alloys attract attention since they have more advantageous mechanical properties than cast Mg alloys. Investigations were carried out the effects of heat treatment on tensile strength and microstructure of AZ61A magnesium alloy. The AZ61A Mg alloy is solution heat treated at the temperature of 6500F (343°C) for various soaking timing such as 120 min, 240 min and 360 minutes and allowed it cool slowly in the furnace itself. Magnesium alloys usually are heat treated either to improve mechanical properties or as means of conditioning for specific fabrication operations. Special attention had been focused on the analysis of mutual relations existing between the deformation conditions, microstructural parameters, grain size and the achieved mechanical properties. The result after the solution heat treatment, showed remarkably improved hardness, tensile strength and yield strength. It would be appropriate for a forming process namely isostatic forming process.

The Microstructure and Compression Behavior of Multi-Step Forging Ti-45Al-8Nb Alloy after Annealing at 1100 °C

2013 ◽  
Vol 747-748 ◽  
pp. 111-114
Author(s):  
Lin Song ◽  
Xiang Jun Xu ◽  
Jun Pin Lin ◽  
Lai Qi Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Annealing Treatment ◽  
Air Cooling ◽  
Test Machine ◽  
Compressive Properties ◽  
Compression Behavior ◽  
Microstructure Change ◽  
Heat Treated ◽  
Before And After

Effects of annealing treatment on microstructure and the compressive properties of hot-worked Ti-45Al-8Nb-(W, B, Y) alloy were investigated. Microstructure of the extrusion plus multi-step forging pancake before and after heat treatment was analyzed by SEM and TEM, respectively. The annealing was conducted by holding samples at 1100°C for 2hrs, and followed by air cooling and furnace cooling. The mechanical properties were measured by Instron test machine. The microstructure evolution during compressive deformation was analyzed by TEM. The results showed that after the annealing the microstructure change could not be observed under SEM but can be observed under TEM. Many dislocation clusters were removed by heat treatment. The heat treated samples had similar compression behaviors with the pancake. TEM investigation showed that the numerous twin intersections occured in γ matrix during compression. The twin spaces tended to decrease as the deformation and the intersection increasing.

Mechanical properties of heat-treated cellulose nanofiber-reinforced polyvinyl alcohol nanocomposite

2016 ◽  
Vol 51 (14) ◽  
pp. 1971-1977 ◽  
Author(s):  
NH Noor Mohamed ◽  
Hitoshi Takagi ◽  
Antonio N Nakagaito
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Polyvinyl Alcohol ◽  
Tensile Tests ◽  
Cellulose Nanofiber ◽  
Heat Treated ◽  
Scanning Electron ◽  
Polyvinyl Alcohol Films

The mechanical properties of cellulose nanofiber-reinforced polyvinyl alcohol composite were studied. Neat polyvinyl alcohol films, cellulose nanofiber sheets, and their nanocomposites containing cellulose nanofiber weight ratios of 5, 15, 30, 40, 45, 50 and 80 wt% were fabricated. Heat treatment by hot pressing at 180℃ was conducted on the specimens to study its effect to the mechanical properties and the results were compared with the non heat-treated specimens. Morphology of the composites was studied by scanning electron microscopy and the mechanical properties were evaluated by means of tensile tests. The results showed that increase of cellulose nanofiber content from 5 wt% to 80 wt% has increased the tensile strength of the composites up to 180 MPa, with cellulose nanofiber content higher than 40 wt% yielding higher tensile strength. The heat-treated specimens exhibited higher tensile strength compared to those of untreated specimens.

Sign in / Sign up

Export Citation Format

Share Document