scholarly journals 3D Printing of Polymer Waste for Improving People’s Awareness about Marine Litter

Polymers ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 1738
Author(s):  
Francesca Ferrari ◽  
Carola Esposito Corcione ◽  
Francesco Montagna ◽  
Alfonso Maffezzoli
Keyword(s):  
Mechanical Response ◽  
Tensile Tests ◽  
Processing Parameters ◽  
Fused Deposition Modelling ◽  
Polymer Waste ◽  
Marine Litter ◽  
Fused Deposition ◽  
Degradation Temperature ◽  
3D Printed ◽  
The Difference

This work is aimed at proposing demonstrative actions devoted to show reprocessing and recyclability of PET originating from bottles collected from the seaside, in order to increase the consumer awareness on the importance of recycling plastics. To this purpose, collected bottles were washed, cut, grinded, extruded in the form of a thin wire adopting different cooling rates, which leads to a modulation of the crystallinity content. Once having optimized the processing parameters, the extruded wire was used to produce 3D printed samples through the fused deposition modelling (FDM). The changes in the crystalline structure due to the different processing conditions were assessed by DSC and XRD analyses, while rheological tests were performed in order to evaluate any modification in the viscosity of PET after repeated processing cycles. The reduction in thermal stability was confirmed by TGA analysis, which showed a progressive decrease in the degradation temperature as processing cycles increased. Finally, tensile tests highlighted the difference in the mechanical response due to the predominance of the crystalline or amorphous phase in the tested sample. In particular, a good mechanical behavior was found for the 3D-printed samples.

scholarly journals Strength Comparison of FDM 3D Printed PLA Made by Different Manufacturers

TEM Journal ◽  
2020 ◽  
pp. 966-970
Author(s):  
Damir Hodžić ◽  
Adi Pandžić ◽  
Ismar Hajro ◽  
Petar Tasić
Keyword(s):  
Experimental Study ◽  
Additive Manufacturing ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Manufacturing Technique ◽  
Plastic Materials ◽  
Wide Range ◽  
3D Printed ◽  
The Difference ◽  
Printing Parameters

Widely used additive manufacturing technique for plastic materials is Fused Deposition Modelling (FDM). The FDM technology has gained interest in industry for a wide range of applications, especially today when large number of different materials on the market are available. There are many different manufacturers for the same FDM material where the difference in price goes up to 50%. This experimental study investigates possible difference in strength of the 3D printed PLA material of five different manufacturers. All specimens are 3D printed on Ultimaker S5 printer with the same printing parameters, and they are all the same colour.

scholarly journals Tribology behaviour investigation of 3D printed polymers

2019 ◽  
Vol 10 (2) ◽  
pp. 173-181
Author(s):  
Muammel M. Hanon ◽  
Márk Kovács ◽  
László Zsidai
Keyword(s):  
Acrylonitrile Butadiene Styrene ◽  
Poly Lactic Acid ◽  
Fused Deposition Modelling ◽  
Tribological Behaviour ◽  
Fused Deposition ◽  
Motion System ◽  
Friction Factors ◽  
The Coefficient Of Friction ◽  
3D Printed ◽  
The Difference

3D printing of Acrylonitrile Butadiene Styrene (ABS) and Poly Lactic Acid (PLA) were used to prepare specimens utilising fused deposition modelling (FDM) technology. Two colours of PLA filament were printed; white and grey, whereas ABS only in white colour. Determining the tribological properties of 3D printed samples have been carried out, through obtaining the frictional features of different 3D printable filaments. Alternating-motion system employed for measuring the tribological factors. Studying the difference between static and dynamic friction factors and the examination of wear values were included. A comparison among the tribological behaviour of the 3D printed polymers has been investigated. The printed white ABS and PLA specimens show insignificant differences in the results tendency. On the contrary, the grey PLA exhibits a considerable variation due to the incredible growth in the coefficient of friction and wear average as well.

scholarly journals Evaluation of Tensile Properties and Damage of Continuous Fibre Reinforced 3D-Printed Parts

2018 ◽  
Vol 774 ◽  
pp. 161-166 ◽  
Author(s):  
Octavio Andrés González-Estrada ◽  
Alberto Pertuz ◽  
Jabid E. Quiroga Mendez
Keyword(s):  
3D Printing ◽  
Tensile Properties ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Three Dimensional ◽  
Tensile Tests ◽  
Fused Deposition Modelling ◽  
Printing Process ◽  
Fused Deposition ◽  
3D Printed

Three-dimensional (3D) printing technology has been traditionally used for the production of prototypes. Recently, developments in 3D printing using Fused Deposition Modelling (FDM) and reinforcement with continuous fibres (fiberglass and carbon fibre), have allowed the manufacture of functional prototypes, considerably improving the mechanical performance of the composite parts. In this work, we characterise the elastic tensile properties of fibre reinforced specimens, considering the variation of several parameters available during the printing process: fibre orientation, volume fraction, fill pattern, reinforcement distribution. Tensile tests were performed according to ASTM D638 to obtain Young’s modulus and ultimate strength for different material configurations available during the printing process. We also perform a fractographic analysis using Scanning Electron Microscopy (SEM) to give an insight of the failure mechanisms present in the specimens.

Effect of Processing Parameters on Mechanical Properties of 3D Printed Samples

2018 ◽  
Vol 919 ◽  
pp. 230-235 ◽  
Author(s):  
Jaroslav Maloch ◽  
Eva Hnátková ◽  
Milan Žaludek ◽  
Petr Krátký
Keyword(s):  
Mechanical Properties ◽  
Low Cost ◽  
Flexural Modulus ◽  
Acrylonitrile Butadiene Styrene ◽  
Processing Parameters ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
3D Printed ◽  
Manufacturing Technologies ◽  
Functional Components

3D printing technology enables the production of functional components in small quantities which can be used as end-use parts. The mechanical properties of the final product define its quality and determine its success or failure in a given application. One at the various additive manufacturing technologies - Fused Deposition Modelling is very often used due to its relatively low cost and the availability of 3D printers and thermoplastic materials. During the process, there are many factors that can affect the mechanical properties of the final product. The temperature of the extrusion nozzle and the layer thickness are two of the basic process parameters. The objective of this work is to investigate the effect of these two processing parameters on the final mechanical properties of the 3D printed samples from acrylonitrile butadiene styrene. Mechanical testing includes the tensile and flexural strength, as well as tensile and flexural modulus.

scholarly journals Influence of fabrication parameters on the elastic modulus and characteristic stresses in 3D printed PLA samples produced via fused deposition modelling technique

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Sebastián Tognana ◽  
Susana Montecinos ◽  
Rosana Gastien ◽  
Walter Salgueiro
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Tensile Tests ◽  
Maximum Tensile Stress ◽  
Specific Yield ◽  
Uniaxial Tensile ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Modes Of Vibration ◽  
3D Printed

Abstract Commonly used 3D printed samples are partially infilled to reduce time and cost of printing, with mechanical properties dependent on the infill. In this work, the influence of the percentage and pattern of infill in PLA printed samples on the elastic modulus and characteristic stresses was analyzed. The elastic modulus, E, and characteristic stresses (σ 0.2, σ 4 and the maximum tensile stress) were determined for each sample using impulse excitation technique, IET, and uniaxial tensile tests. An apparent density was calculated for each pattern and infill percentage, and the mechanical parameters were studied as a function of such density. The results of IET obtained in different modes of vibration were analyzed and an apparent value of E was calculated. FEM simulations were carried out and the results were compared with the experimental ones. The mechanical properties for different infill percentages and infill patterns were studied by comparing the specific values of E and the stresses. Samples with higher infill percentages exhibit the best specific values of maximum stress and E, but the sample with 20% infill has the highest specific yield stress and a good value of the specific E from flexural vibrations.

scholarly journals 3D Printed Clamps for In Vitro Tensile Tests of Human Gracilis and the Superficial Third of Quadriceps Tendons

2021 ◽  
Vol 11 (6) ◽  
pp. 2563
Author(s):  
Ivan Grgić ◽  
Vjekoslav Wertheimer ◽  
Mirko Karakašić ◽  
Željko Ivandić
Keyword(s):  
3D Printing ◽  
Fused Deposition Modeling ◽  
Tensile Tests ◽  
Biomechanical Properties ◽  
Testing Procedure ◽  
Laboratory Equipment ◽  
Fused Deposition ◽  
Custom Made ◽  
3D Printed

Recent soft tissue studies have reported issues that occur during experimentation, such as the tissue slipping and rupturing during tensile loads, the lack of standard testing procedure and equipment, the necessity for existing laboratory equipment adaptation, etc. To overcome such issues and fulfil the need for the determination of the biomechanical properties of the human gracilis and the superficial third of the quadriceps tendons, 3D printed clamps with metric thread profile-based geometry were developed. The clamps’ geometry consists of a truncated pyramid pattern, which prevents the tendons from slipping and rupturing. The use of the thread application in the design of the clamp could be used in standard clamping development procedures, unlike in previously custom-made clamps. Fused deposition modeling (FDM) was used as a 3D printing technique, together with polylactic acid (PLA), which was used as a material for clamp printing. The design was confirmed and the experiments were conducted by using porcine and human tendons. The findings justify the usage of 3D printing technology for parts manufacturing in the case of tissue testing and establish independence from the existing machine clamp system, since it was possible to print clamps for each prepared specimen and thus reduce the time for experiment setup.

scholarly journals Fused Deposition Modelling of Fibre Reinforced Polymer Composites: A Parametric Review

2021 ◽  
Vol 5 (1) ◽  
pp. 29
Author(s):  
Narongkorn Krajangsawasdi ◽  
Lourens G. Blok ◽  
Ian Hamerton ◽  
Marco L. Longana ◽  
Benjamin K. S. Woods ◽  
...  
Keyword(s):  
Process Parameters ◽  
Mechanical Performance ◽  
Fibre Length ◽  
Processing Parameters ◽  
Thermoplastic Composite ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Fibre Reinforced Polymer ◽  
Printing Parameters

Fused deposition modelling (FDM) is a widely used additive layer manufacturing process that deposits thermoplastic material layer-by-layer to produce complex geometries within a short time. Increasingly, fibres are being used to reinforce thermoplastic filaments to improve mechanical performance. This paper reviews the available literature on fibre reinforced FDM to investigate how the mechanical, physical, and thermal properties of 3D-printed fibre reinforced thermoplastic composite materials are affected by printing parameters (e.g., printing speed, temperature, building principle, etc.) and constitutive materials properties, i.e., polymeric matrices, reinforcements, and additional materials. In particular, the reinforcement fibres are categorized in this review considering the different available types (e.g., carbon, glass, aramid, and natural), and obtainable architectures divided accordingly to the fibre length (nano, short, and continuous). The review attempts to distil the optimum processing parameters that could be deduced from across different studies by presenting graphically the relationship between process parameters and properties. This publication benefits the material developer who is investigating the process parameters to optimize the printing parameters of novel materials or looking for a good constituent combination to produce composite FDM filaments, thus helping to reduce material wastage and experimental time.

scholarly journals Influence of the Infill Geometry of 3D-Printed Tablets on Drug Dissolution

2021 ◽  
Vol 5 (1) ◽  
pp. 15
Author(s):  
Nuno Venâncio ◽  
Gabriela G. Pereira ◽  
João F. Pinto ◽  
Ana I. Fernandes
Keyword(s):  
Three Dimensional ◽  
Drug Dissolution ◽  
Fused Deposition Modelling ◽  
Three Dimensional Printing ◽  
Preliminary Results ◽  
Fused Deposition ◽  
3D Printed ◽  
Dimensional Printing ◽  
Hot Melt ◽  
Patient Centric

Patient-centric therapy is especially important in pediatrics and may be attained by three-dimensional printing. Filaments containing 30% w/w of theophylline were produced by hot-melt extrusion and printed using fused deposition modelling to produce tablets. Here, preliminary results evaluating the effect of infill geometry (cross, star, grid) on drug content and release are reported.

Sign in / Sign up

Export Citation Format

Share Document