scholarly journals A Green Approach to Modify Surface Properties of Polyurethane Foam for Enhanced Oil Absorption

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 1883 ◽  
Author(s):  
Zhi Chien Ng ◽  
Rosyiela Azwa Roslan ◽  
Woei Jye Lau ◽  
Mehmet Gürsoy ◽  
Mustafa Karaman ◽  
...  
Keyword(s):  
Surface Properties ◽  
Positive Impact ◽  
Chemical Vapor ◽  
Surface Hydrophobicity ◽  
Absorption Efficiency ◽  
Oil Absorption ◽  
Water Contact ◽  
Green Approach ◽  
Pu Foam ◽  
Modify Surface

The non-selective property of conventional polyurethane (PU) foam tends to lower its oil absorption efficiency. To address this issue, we modified the surface properties of PU foam using a rapid solvent-free surface functionalization approach based on the chemical vapor deposition (CVD) method to establish an extremely thin yet uniform coating layer to improve foam performance. The PU foam was respectively functionalized using different monomers, i.e., perfluorodecyl acrylate (PFDA), 2,2,3,4,4,4-hexafluorobutyl acrylate (HFBA), and hexamethyldisiloxane (HMDSO), and the effect of deposition times (1, 5 and 10 min) on the properties of foam was investigated. The results showed that all the modified foams demonstrated a much higher water contact angle (i.e., greater hydrophobicity) and greater absorption capacities compared to the control PU foam. This is due to the presence of specific functional groups, e.g., fluorine (F) and silane (Si) in the modified PU foams. Of all, the PU/PHFBAi foam exhibited the highest absorption capacities, recording 66.68, 58.15, 53.70, and 58.38 g/g for chloroform, acetone, cyclohexane, and edible oil, respectively. These values were 39.19–119.31% higher than that of control foam. The promising performance of the PU/PHFBAi foam is due to the improved surface hydrophobicity attributed to the original perfluoroalkyl moieties of the HFBA monomer. The PU/PHFBAi foam also demonstrated a much more stable absorption performance compared to the control foam when both samples were reused for up to 10 cycles. This clearly indicates the positive impact of the proposed functionalization method in improving PU properties for oil absorption processes.

scholarly journals Integration of Polypyrrole Electrode into Piezoelectric PVDF Energy Harvester with Improved Adhesion and Over-Oxidation Resistance

Polymers ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 1071
Author(s):  
Kyungha Baik ◽  
Sohyun Park ◽  
Changsang Yun ◽  
Chung Hee Park
Keyword(s):  
Energy Harvester ◽  
Chemical Vapor ◽  
Aluminum Foil ◽  
Surface Hydrophobicity ◽  
Alkaline Treatment ◽  
Electrode System ◽  
Pvdf Film ◽  
Smart Textiles ◽  
Water Contact ◽  
Hydrophobic Coating

Smart textiles for wearable devices require flexibility and a lightweight, so in this study, a soft polypyrrole (PPy) electrode system was integrated into a piezoelectric polyvinylidenefluoride (PVDF) energy harvester. The PVDF energy harvester integrated with a PPy electrode had the piezoelectric output voltage of 4.24–4.56 V, while the PVDF energy harvester with an additional aluminum-foil electrode exhibited 2.57 V. Alkaline treatment and chemical vapor deposition with n-dodecyltrimethoxysilane (DTMS) were employed to improve the adhesion between the PVDF and PPy and the resistance to over-oxidation in aqueous solutions. The PVDF film modified by an alkaline treatment could have the improved adhesion via the introduction of polar functional groups to its surface, which was confirmed by the ultrasonication. The surface hydrophobicity of the PPy electrode was enhanced by the DTMS coating, resulting in the improvement of the resistance to over-oxidation with a water contact angle of 111°. Even with the hydrophobic coating, the electrodes remained electroconductive and continued to transfer an electric charge, maintaining the piezoelectricity of the PVDF film. The developed electrode-integrated energy harvester is expected to be applied to smart textiles because it offers the advantages of efficient piezoelectric generation, flexibility, and durability.

Laser-Induced Nanocarbon Formation for Tuning Surface Properties of Commercial Polymers

2020 ◽  
Author(s):  
Moataz Abdulhafez ◽  
Angela J. McComb ◽  
Mostafa Bedewy
Keyword(s):  
Contact Angle ◽  
Surface Properties ◽  
Surface Characterization ◽  
Surface Engineering ◽  
Surface Hydrophobicity ◽  
Contact Angles ◽  
Structure Property ◽  
Water Contact ◽  
Wide Range ◽  
Commercial Polymers

Abstract The growth of laser-induced nanocarbons, referred to here are LINC for short, directly on polymeric surfaces is a promising route toward surface engineering of commercial polymers. This paper aims to demonstrate how this new approach can enable achieving varied surface properties based on tuning the nanostructured morphology of the formed graphitic material on commercial polyimide (Kapton) films. We elucidate the effects of tuning laser processing parameters on the achieved nanoscale morphology and the resulting surface hydrophobicity or hydrophilicity. Our results show that by varying lasing power, rastering speed, laser spot size, and line-to-line gap sizes, a wide range of water contact angles are possible, i.e. from below 20° to above 110°. Combining water contact angle measurements from an optical tensiometer with LINC surface characterization using optical microscopy, electron microscopy, and Raman spectroscopy enables building the process-structure-property relationship. Our findings reveal that both the value of contact angle and the anisotropic wetting behavior of LINC on polyimide are dependent on their hierarchical surface nanostructure which ranges for isotropic nanoporous morphology to fibrous morphology. Results also show that increasing gap sizes lead to an increase in contact angles and thus an increase in the hydrophobicity of the surface. Hence, our work highlight the potential of this approach for manufacturing flexible devices with tailored surfaces.

scholarly journals The Effect of Hydroxyl on the Superhydrophobicity of Dodecyl Methacrylate (LMA) Coated Fabrics through Simple Dipping-Plasma Crosslinked Method

Coatings ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1263
Author(s):  
Liyun Xu ◽  
Yu Zhang ◽  
Ying Guo ◽  
Ruiyun Zhang ◽  
Jianjun Shi ◽  
...  
Keyword(s):  
Thermoplastic Polyurethane ◽  
Hydrophobic Effect ◽  
Surface Hydrophobicity ◽  
Contact Angles ◽  
Binding Property ◽  
Interesting Phenomenon ◽  
Water Contact ◽  
Capacitively Coupled ◽  
Pet Fabric ◽  
Dodecyl Methacrylate

In order to obtain stable superhydrophobicity, suitable hydrophobic treatment agents should be selected according to different material properties. In this paper, cotton and poly(ethylene terephthalate) (PET) fabrics were respectively coated with dodecyl methacrylate (LMA) via argon combined capacitively coupled plasma (CCP), and the surface hydrophobicity and durability of the treated cotton and polyester fabrics are also discussed. An interesting phenomenon happened, whereby the LMA-coated cotton fabric (Cotton-g-LMA) had better water repelling and mechanical durability properties than LMA-coated PET fabric (PET-g-LMA), and LMA-coated hydroxyl-grafted PET fabrics (PET fabrics were successively coated with polyethylene glycol (PEG) and LMA, PET-g-PEG & LMA) had a similar performance to cotton fabrics. The water contact angles of Cotton-g-LMA, PET-g-LMA and PET-g-PEG & LMA were 156°, 153° and 155°, respectively, and after 45 washing cycles or 1000 rubbing cycles, the corresponding water contact angles decreased to 145°, 88°, 134° and 146°, 127° and 143°, respectively. Additionally, thermoplastic polyurethane (TPU) and polyamides-6 (PA6) fabrics all exhibited the same properties as the PET fabric. Therefore, the grafting of hydroxyl can improve the hydrophobic effect of LMA coating and the binding property between LMA and fabrics effectively, without changing the wearing comfort.

scholarly journals On the Effectiveness of Oxygen Plasma and Alkali Surface Treatments to Modify the Properties of Polylactic Acid Scaffolds

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1643
Author(s):  
Ricardo Donate ◽  
María Elena Alemán-Domínguez ◽  
Mario Monzón
Keyword(s):  
Surface Properties ◽  
Enzymatic Degradation ◽  
Oxygen Plasma ◽  
Physicochemical Characterization ◽  
Surface Treatments ◽  
Carboxyl Groups ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Angle Measurements ◽  
3D Printed

Surface modification of 3D-printed PLA structures is a major issue in terms of increasing the biofunctionality and expanding the tissue engineering applications of these parts. In this paper, different exposure times were used for low-pressure oxygen plasma applied to PLA 3D-printed scaffolds. Alkali surface treatments were also evaluated, aiming to compare the modifications introduced on the surface properties by each strategy. Surface-treated samples were characterized through the quantification of carboxyl groups, energy-dispersive X-ray spectroscopy, water contact angle measurements, and differential scanning calorimetry analysis. The change in the surface properties was studied over a two-week period. In addition, an enzymatic degradation analysis was carried out to evaluate the effect of the surface treatments on the degradation profile of the 3D structures. The physicochemical characterization results suggest different mechanism pathways for each type of treatment. Alkali-treated scaffolds showed a higher concentration of carboxyl groups on their surface, which enhanced the enzymatic degradation rate, but were also proven to be more aggressive towards 3D-printed structures. In contrast, the application of the plasma treatments led to an increased hydrophilicity of the PLA surface without affecting the bulk properties. However, the changes on the properties were less steady over time.

scholarly journals Highly efficient reusable superhydrophobic sponge prepared by a facile, simple and cost effective biomimetic bonding method for oil absorption

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Jiaqi Wang ◽  
Yan Chen ◽  
Qinyao Xu ◽  
Miaomiao Cai ◽  
Qian Shi ◽  
...  
Keyword(s):  
Environmentally Friendly ◽  
Absorption Capacity ◽  
Oil Absorption ◽  
Water Contact ◽  
Water Separation ◽  
Highly Efficient ◽  
Study Results ◽  
Different Types ◽  
Modification Method ◽  
Bonding Method

AbstractSuperhydrophobic sponges have considerable potential for oil/water separation. Most of the methods used for superhydrophobic modification of sponges require toxic or harmful solvents, which have the drawbacks of hazardous to environment, expensive, and complex to utilize. Moreover, the hydrophobic layer on the surface of sponge is often easily destroyed. In this paper, a highly efficient superhydrophobic sponge with excellent reusability was developed by using a facile, simple and environmentally friendly dopamine biomimetic bonding method. Different types of sponges, such as melamine, polyethylene or polyurethane sponge wastes, were used as raw materials to prepare superhydrophobic sponges, which possess the advantages of inexpensive and abundant. The effects of different dopamine polymerization time and different hydrophobic agent dosage on the hydrophobicity and oil absorption capacity of melamine sponges were optimized. The study results showed that the water contact angle of the superhydrophobic sponge could reach 153° with excellent organic solvent absorption capacity of 165.9 g/g. Furthermore, the superhydrophobic sponge retained approximately 92.1% of its initial absorption capacity after 35 reutilization cycles. More importantly, the dopamine biomimetic bonding superhydrophobic modification method can be used for different types of sponges. Therefore, a universally applicable, facile, simple and environmentally friendly superhydrophobic modification method for sponges was developed.

scholarly journals Tunable Crystalline Phases in UV-Curable PEG-Grafted Ladder-Structured Silsesquioxane/Polyimide Composites

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2295 ◽  
Author(s):  
Ryung Il Kim ◽  
Ju Ho Shin ◽  
Jong Suk Lee ◽  
Jung-Hyun Lee ◽  
Albert S. Lee ◽  
...  
Keyword(s):  
Polymer Composites ◽  
Surface Properties ◽  
Weight Ratio ◽  
Hybrid Polymer ◽  
Water Contact ◽  
Uv Curable ◽  
Wide Range ◽  
Drastic Increase ◽  
Polyimide Composites ◽  
Crystalline Polyethylene

A series of UV-curable hybrid composite blends containing a carboxylic acid functionalized polyimidewith varying amounts of high molecular weight (~1 K) PEG-grafted ladder-structured polysilsesquioxanes copolymerized with methacryl groups were fabricated and their structural, thermal, mechanical, and surface properties characterized. At a composite weight ratio of polyimide above 50 wt.%, a stark shift from amorphous to crystalline polyethylene glycol (PEG) phases were observed, accompanied by a drastic increase in both surface moduli and brittleness index. Moreover, fabricated composites were shown to have a wide range water contact angle, 9.8°–73.8°, attesting to the tunable surface properties of these amphiphilic hybrid polymer composites. The enhanced mechanical properties, combined with the utility of tunable surface hydrophilicity allows for the possible use of these hybrid polymer composites to be utilized as photosensitive polyimide negative photoresists for a myriad of semiconductor patterning processes.

scholarly journals AACVD Synthesis and Characterization of Iron and Copper Oxides Modified ZnO Structured Films

Nanomaterials ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 471 ◽  
Author(s):  
Martha Claros ◽  
Milena Setka ◽  
Yecid P. Jimenez ◽  
Stella Vallejos
Keyword(s):  
Contact Angle ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Contact Angles ◽  
Copper Oxides ◽  
Water Contact ◽  
X Ray ◽  
Hydrophobic Behavior

Non-modified (ZnO) and modified (Fe2O3@ZnO and CuO@ZnO) structured films are deposited via aerosol assisted chemical vapor deposition. The surface modification of ZnO with iron or copper oxides is achieved in a second aerosol assisted chemical vapor deposition step and the characterization of morphology, structure, and surface of these new structured films is discussed. X-ray photoelectron spectrometry and X-ray diffraction corroborate the formation of ZnO, Fe2O3, and CuO and the electron microscopy images show the morphological and crystalline characteristics of these structured films. Static water contact angle measurements for these structured films indicate hydrophobic behavior with the modified structures showing higher contact angles compared to the non-modified films. Overall, results show that the modification of ZnO with iron or copper oxides enhances the hydrophobic behavior of the surface, increasing the contact angle of the water drops at the non-modified ZnO structures from 122° to 135° and 145° for Fe2O3@ZnO and CuO@ZnO, respectively. This is attributed to the different surface properties of the films including the morphology and chemical composition.

In situ detection of cell surface hydrophobicity of probe-defined bacteria in activated sludge

2001 ◽  
Vol 43 (6) ◽  
pp. 97-103 ◽  
Author(s):  
J. L. Nielsen ◽  
L. H. Mikkelsen ◽  
P. H. Nielsen
Keyword(s):  
Activated Sludge ◽  
Surface Properties ◽  
Treatment Plant ◽  
Cell Surface Hydrophobicity ◽  
Surface Hydrophobicity ◽  
Substrate Uptake ◽  
Filamentous Bacteria ◽  
In Situ Conditions ◽  
Bacterial Surfaces

The surface hydrophobicity of different types of bacteria in activated sludge were investigated under in situ conditions by following the adhesion of fluorescent microspheres with defined surface properties to bacterial surfaces (the MAC-method). This technique was combined with identification of the bacteria with fluorescence in situ hybridization with rRNA-targeted oligonucleotides (FISH) and could thus be used for characterization of surface properties of probe-defined bacteria directly in a complex system without prior enrichment or isolation. This MAC-FISH technique could be used for single bacteria as well as filamentous bacteria. In the investigated activated sludge from an industrial wastewater treatment plant, two types of filamentous bacteria dominated. One morphotype consistently attracted only very few hydrophobic microspheres, indicating that the thin sheath of exopolymers around the cells had a hydrophilic surface. Use of a hierarchical set of gene probes revealed that these filaments were sulphide oxidising Thiothrix spp. The other predominating filamentous morphotype had a thick, very hydrophobic exopolymeric sheath. This filamentous bacterium was found to belong to the alpha-Proteobacteria. The relevance of the significant differences in surface hydrophobicity for the two morphotypes in respect to substrate uptake and floc formation is discussed.

Sign in / Sign up

Export Citation Format

Share Document