scholarly journals ON/OFF Switchable Nanocomposite Membranes for Separations

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2415
Author(s):  
Taegyun Kwon ◽  
Jinyoung Chun
Keyword(s):  
Membrane Separation ◽  
Polymer Nanocomposite ◽  
Membrane System ◽  
Polymeric Membranes ◽  
Human Consumption ◽  
Stimuli Responsive ◽  
Permeate Flux ◽  
Future Direction ◽  
The Cost ◽  
External Stimuli

Although water, air, and other resources are abundant on earth, they have been subjected to strict environmental regulations. This is because of their limitation of availability for human consumption. In the separation industry, the membrane system was introduced to increase the amount of resources available to mankind. Experts used an easy-to-use polymeric material to design several membranes with porous structures for wastewater treatment, gas separation, and chemical removal; consequently, they succeeded in obtaining positive results. However, past polymeric membranes exhibited a chronic drawback such that it was difficult to simultaneously augment the permeate flux and improve its selectivity toward certain substances. Because of the trade-off relationship that existed between permeability and selectivity, the membrane efficiency was not very good; consequently, the cost-effectiveness was significantly hindered because there was no other alternative than to replace the membrane in order to maintain its initial characteristics steadily. This review begins with the introduction of a polymer nanocomposite (PNC) membrane that has been designed to solve the chronic problem of polymeric membranes; subsequently, the stimuli-responsive PNC membrane is elucidated, which has established itself as a popular topic among researchers in the separation industry for several decades. Furthermore, we have listed the different types and examples of stimuli-responsive PNC membranes, which can be switched by external stimuli, while discussing the future direction of the membrane separation industry.

scholarly journals Hybrid System Coupling Moving Bed Bioreactor with UV/O3 Oxidation and Membrane Separation Units for Treatment of Industrial Laundry Wastewater

Materials ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2648
Author(s):  
Sylwia Mozia ◽  
Magdalena Janus ◽  
Sławomira Bering ◽  
Krzysztof Tarnowski ◽  
Jacek Mazur ◽  
...  
Keyword(s):  
Membrane Fouling ◽  
Membrane Separation ◽  
Oxygen Demand ◽  
Membrane System ◽  
Permeate Flux ◽  
Moving Bed ◽  
System A ◽  
Water Recycle ◽  
Recycle And Reuse ◽  
System Coupling

This paper describes the investigations on the possibilities of treatment of wastewater generated in an industrial laundry with application of a combined biological-photooxidation- membrane system aimed at water recycle and reuse. The two treatment schemes were compared: 1) scheme A consisting of a treatment in a moving bed biological reactor (MBBR) followed by microfiltration (MF) and nanofiltration (NF), and 2) scheme B comprising MBBR followed by oxidation by photolysis enhanced with in situ generated O3 (UV/O3) after which MF and NF were applied. The removal efficiency in MBBR reached 95–97% for the biochemical oxygen demand; 90–93% for the chemical oxygen demand and 89–99% for an anionic and a nonionic surfactants. The application of UV/O3 system allowed to decrease the content of the total organic carbon by 68% after 36 h of operation with a mineralization rate of 0.36 mg/L·h. Due to UV/O3 pretreatment, a significant mitigation of membrane fouling in the case of both MF and NF processes was achieved. The MF permeate flux in the system B was over two times higher compared to that in the system A. Based on the obtained results it was concluded that the laundry wastewater pretreated in the MBBR-UV/O3-MF-NF system could be recycled to any stage of the laundry process.

scholarly journals Hybrid gravitational microfiltration system for drinking water purification

2017 ◽  
Vol 12 (2) ◽  
pp. 168 ◽  
Author(s):  
Natália Ueda Yamaguchi ◽  
Silvia Amélia Liwa Abe ◽  
Flávia Vieira da Silva Medeiros ◽  
Angélica Marquetotti Salcedo Vieira ◽  
Rosangela Bergamasco
Keyword(s):  
Electron Microscopy ◽  
Escherichia Coli ◽  
Copper Oxide ◽  
Membrane System ◽  
Copper Oxide Nanoparticles ◽  
Human Consumption ◽  
Permeate Flux ◽  
Point Of Use ◽  
Quality Of Water

This study evaluates the application of a polymeric microfiltration membrane in a gravitational filtration module and its combination with granular activated carbon (GAC) impregnated with copper, resulting in a hybrid process. The proposed system would be used to improve the quality of water for human consumption in developing countries.  Permeate flux, pH, Escherichia coli removal, color, turbidity and free chlorine removals were evaluated in the applied process. Instrumental techniques, such as N2 adsorption at 77 K, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDX) analyses were used to characterize the proposed membrane and adsorbent. The GAC ensured higher chlorine removals, as well as higher permeate flux. Furthermore, the GAC impregnated with copper oxide nanoparticles exhibited higher Escherichia coli removal. Therefore, the hybrid gravitational membrane system applying GAC impregnated with copper oxide could be considered as a potential alternative point-of-use treatment to improve the quality of water for human consumption.

scholarly journals Characteristics of Polymeric Ultrafiltration Membranes Produced with the Use of Graphene Oxide

2018 ◽  
Vol 25 (3) ◽  
pp. 419-429
Author(s):  
Elwira Tomczak ◽  
Martyna Blus
Keyword(s):  
Graphene Oxide ◽  
Carbon Nanostructures ◽  
Polyvinylidene Fluoride ◽  
Phase Inversion ◽  
Membrane System ◽  
Polymeric Membranes ◽  
Mass Transfer Resistance ◽  
Permeate Flux ◽  
Transfer Resistance ◽  
Typical Composition

Abstract This article describes a method for producing polymeric membranes by adding carbon nanostructures in the form of graphene oxide (GO). The reference membrane (having typical composition) was formed via phase inversion, using polyvinylidene fluoride (PVDF) dissolved in dimethylacetamide (DMAC). The polymeric matrix was additionally enriched with a plasticizer, i.e. polyethylene glycol (PEG). Afterwards, graphene oxide ultrasonically dispersed in dimethylacetamide was added to basic matrix. The membranes were further compared with one another by measuring their contact angle and hydrodynamics. The results were compared with the literature reports. The transport properties of the membranes were assessed with experimental ultrafiltration equipment (KOCH Membrane System). Also, their permeate flux and mass transfer resistance were determined.

Smart Polymers and their Applications: A Review

2017 ◽  
Vol 8 (03) ◽  
Author(s):  
Gore S. A. ◽  
Gholve S. B. ◽  
Savalsure S. M. ◽  
Ghodake K. B. ◽  
Bhusnure O. G. ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Water Soluble ◽  
Solution Temperature ◽  
Smart Polymers ◽  
Stimuli Responsive ◽  
Responsive Materials ◽  
Water Soluble Polymers ◽  
Commercial Applications ◽  
Stimuli Sensitive ◽  
External Stimuli

Smart polymers are materials that respond to small external stimuli. These are also referred as stimuli responsive materials or intelligent materials. Smart polymers that can exhibit stimuli-sensitive properties are becoming important in many commercial applications. These polymers can change shape, strength and pore size based on external factors such as temperature, pH and stress. The stimuli include salt, UV irradiation, temperature, pH, magnetic or electric field, ionic factors etc. Smart polymers are very promising applicants in drug delivery, tissue engineering, cell culture, gene carriers, textile engineering, oil recovery, radioactive wastage and protein purification. The study is focused on the entire features of smart polymers and their most recent and relevant applications. Water soluble polymers with tunable lower critical solution temperature (LCST) are of increasing interest for biological applications such as cell patterning, smart drug release, DNA sequencing etc.

scholarly journals Dynamic Manipulation of THz Waves Enabled by Phase-Transition VO2 Thin Film

Nanomaterials ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 114
Author(s):  
Chang Lu ◽  
Qingjian Lu ◽  
Min Gao ◽  
Yuan Lin
Keyword(s):  
Optical Methods ◽  
Stimuli Responsive ◽  
Device Structure ◽  
Current State ◽  
Insulator Metal Transition ◽  
Potential Applications ◽  
Fs Laser ◽  
External Stimuli ◽  
Thz Applications ◽  
Thz Waves

The reversible and multi-stimuli responsive insulator-metal transition of VO2, which enables dynamic modulation over the terahertz (THz) regime, has attracted plenty of attention for its potential applications in versatile active THz devices. Moreover, the investigation into the growth mechanism of VO2 films has led to improved film processing, more capable modulation and enhanced device compatibility into diverse THz applications. THz devices with VO2 as the key components exhibit remarkable response to external stimuli, which is not only applicable in THz modulators but also in rewritable optical memories by virtue of the intrinsic hysteresis behaviour of VO2. Depending on the predesigned device structure, the insulator-metal transition (IMT) of VO2 component can be controlled through thermal, electrical or optical methods. Recent research has paid special attention to the ultrafast modulation phenomenon observed in the photoinduced IMT, enabled by an intense femtosecond laser (fs laser) which supports “quasi-simultaneous” IMT within 1 ps. This progress report reviews the current state of the field, focusing on the material nature that gives rise to the modulation-allowed IMT for THz applications. An overview is presented of numerous IMT stimuli approaches with special emphasis on the underlying physical mechanisms. Subsequently, active manipulation of THz waves through pure VO2 film and VO2 hybrid metamaterials is surveyed, highlighting that VO2 can provide active modulation for a wide variety of applications. Finally, the common characteristics and future development directions of VO2-based tuneable THz devices are discussed.

scholarly journals Effect of Pre-Oxidation on Coagulation/Ceramic Membrane Treatment of Yangtze River Water

Membranes ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 369
Author(s):  
Shengji Xia ◽  
Xinran Zhang ◽  
Yuanchen Zhao ◽  
Fibor J. Tan ◽  
Pan Li ◽  
...  
Keyword(s):  
Water Treatment ◽  
Membrane Fouling ◽  
Membrane Filtration ◽  
Ceramic Membrane ◽  
Membrane Separation ◽  
Membrane System ◽  
Coagulation System ◽  
Fouling Control ◽  
Filtration System ◽  
Membrane Treatment

The membrane separation process is being widely used in water treatment. It is very important to control membrane fouling in the process of water treatment. This study was conducted to evaluate the efficiency of a pre-oxidation-coagulation flat ceramic membrane filtration process using different oxidant types and dosages in water treatment and membrane fouling control. The results showed that under suitable concentration conditions, the effect on membrane fouling control of a NaClO pre-oxidation combined with a coagulation/ceramic membrane system was better than that of an O3 system. The oxidation process changed the structure of pollutants, reduced the pollution load and enhanced the coagulation process in a pre-oxidation-coagulation system as well. The influence of the oxidant on the filtration system was related to its oxidizability and other characteristics. NaClO and O3 performed more efficiently than KMnO4. NaClO was more conducive to the removal of DOC, and O3 was more conducive to the removal of UV254.

scholarly journals Metal-Organic Framework-Based Stimuli-Responsive Polymers

2021 ◽  
Vol 5 (4) ◽  
pp. 101
Author(s):  
Menglian Wei ◽  
Yu Wan ◽  
Xueji Zhang
Keyword(s):  
Metal Organic Framework ◽  
Chemical Properties ◽  
Stimuli Responsive ◽  
Guest Molecules ◽  
Stimuli Responsive Polymers ◽  
Responsive Polymers ◽  
Reversible Phase Transition ◽  
Metal Organic ◽  
External Stimuli ◽  
Organic Framework

Metal-organic framework (MOF) based stimuli-responsive polymers (coordination polymers) exhibit reversible phase-transition behavior and demonstrate attractive properties that are capable of altering physical and/or chemical properties upon exposure to external stimuli, including pH, temperature, ions, etc., in a dynamic fashion. Thus, their conformational change can be imitated by the adsorption/desorption of target analytes (guest molecules), temperature or pressure changes, and electromagnetic field manipulation. MOF-based stimuli responsive polymers have received great attention due to their advanced optical properties and variety of applications. Herein, we summarized some recent progress on MOF-based stimuli-responsive polymers (SRPs) classified by physical and chemical responsiveness, including temperature, pressure, electricity, pH, metal ions, gases, alcohol and multi-targets.

External Stimuli-Responsive Nanoparticles for Spatially and Temporary Controlled Delivery of CRISPR-Cas Genome Editors

2021 ◽  
Author(s):  
Ruosen Xie ◽  
Yuyuan Wang ◽  
Shaoqin Gong
Keyword(s):  
Genome Editing ◽  
Genetic Diseases ◽  
Delivery Systems ◽  
Controlled Delivery ◽  
Stimuli Responsive ◽  
New Therapies ◽  
External Stimuli

The CRISPR–Cas9 system is a powerful tool for genome editing, which can potentially lead to new therapies for genetic diseases. Up to date, various viral and non-viral delivery systems have...

Application of neural networks in membrane separation

2020 ◽  
Vol 36 (2) ◽  
pp. 265-310 ◽  
Author(s):  
Morteza Asghari ◽  
Amir Dashti ◽  
Mashallah Rezakazemi ◽  
Ebrahim Jokar ◽  
Hadi Halakoei
Keyword(s):  
Neural Networks ◽  
Chemical Engineering ◽  
Membrane Separation ◽  
Mechanistic Model ◽  
Computing Time ◽  
Permeate Flux ◽  
Practical Applications ◽  
Advantages And Disadvantages ◽  
Wide Range ◽  
Physical And Chemical

AbstractArtificial neural networks (ANNs) as a powerful technique for solving complicated problems in membrane separation processes have been employed in a wide range of chemical engineering applications. ANNs can be used in the modeling of different processes more easily than other modeling methods. Besides that, the computing time in the design of a membrane separation plant is shorter compared to many mass transfer models. The membrane separation field requires an alternative model that can work alone or in parallel with theoretical or numerical types, which can be quicker and, many a time, much more reliable. They are helpful in cases when scientists do not thoroughly know the physical and chemical rules that govern systems. In ANN modeling, there is no requirement for a deep knowledge of the processes and mathematical equations that govern them. Neural networks are commonly used for the estimation of membrane performance characteristics such as the permeate flux and rejection over the entire range of the process variables, such as pressure, solute concentration, temperature, superficial flow velocity, etc. This review investigates the important aspects of ANNs such as methods of development and training, and modeling strategies in correlation with different types of applications [microfiltration (MF), ultrafiltration (UF), nanofiltration (NF), reverse osmosis (RO), electrodialysis (ED), etc.]. It also deals with particular types of ANNs that have been confirmed to be effective in practical applications and points out the advantages and disadvantages of using them. The combination of ANN with accurate model predictions and a mechanistic model with less accurate predictions that render physical and chemical laws can provide a thorough understanding of a process.

A Wall Film Model for Membrane Fouling

2018 ◽  
Author(s):  
Sina Jahangiri Mamouri ◽  
Volodymyr V. Tarabara ◽  
André Bénard
Keyword(s):  
Multiphase Flow ◽  
Membrane Fouling ◽  
Oil And Gas ◽  
Membrane Separation ◽  
Film Formation ◽  
Membrane Surface ◽  
Permeate Flux ◽  
Water Separation ◽  
Wall Film ◽  
Oil Water

Deoiling of produced or impaired waters associated with oil and gas production represents a significant challenge for many companies. Centrifugation, air flotation, and hydrocyclone separation are the current methods of oil removal from produced water [1], however the efficiency of these methods decreases dramatically for droplets smaller than approximately 15–20 μm. More effective separation of oil-water mixtures into water and oil phases has the potential to both decrease the environmental footprint of the oil and gas industry and improve human well-being in regions such as the Gulf of Mexico. New membrane separation processes and design of systems with advanced flow management offer tremendous potential for improving oil-water separation efficacy. However, fouling is a major challenge in membrane separation [2]. In this study, the behavior of oil droplets and their interaction with crossflow filtration (CFF) membranes (including membrane fouling) is studied using computational fluid dynamics (CFD) simulations. A model for film formation on a membrane surface is proposed for the first time to simulate film formation on membrane surfaces. The bulk multiphase flow is modeled using an Eulerian-Eulerian multiphase flow model. A wall film is developed from mass and momentum balances [3] and implemented to model droplet deposition and membrane surface blockage. The model is used to predict film formation and subsequent membrane fouling, and allow to estimate the actual permeate flux. The results are validated using available experimental data.

Sign in / Sign up

Export Citation Format

Share Document