scholarly journals Extraction and Characterization of Natural Cellulosic Fiber from Pandanus amaryllifolius Leaves

Polymers ◽  
2021 ◽  
Vol 13 (23) ◽  
pp. 4171
Author(s):  
Z. N. Diyana ◽  
R. Jumaidin ◽  
M. Z. Selamat ◽  
R. H. Alamjuri ◽  
Fahmi Asyadi Md Yusof
Keyword(s):  
Moisture Absorption ◽  
Lignin Content ◽  
Fibre Diameter ◽  
Extraction Process ◽  
Single Fibre ◽  
Polymerization Process ◽  
Composition Analysis ◽  
Fibre Reinforcement ◽  
Pandanus Amaryllifolius

Pandanus amaryllifolius is a member of Pandanaceae family and is abundant in south-east Asian countries including Malaysia, Thailand, Indonesia and India. In this study, Pandanus amaryllifolius fibres were extracted via a water retting extraction process and were investigated as potential fibre reinforcement in polymer composite. Several tests were carried out to investigate the characterization of Pandanus amaryllifolius fibre such as chemical composition analysis which revealed Pandanus amaryllifolius fibre’s cellulose, hemicellulose and lignin content of 48.79%, 19.95% and 18.64% respectively. Material functional groups were analysed by using Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction analysis confirming the presence of cellulose and amorphous substances in the fibre. The morphology of extracted Pandanus amaryllifolius fibre was studied using a scanning electron microscope (SEM). Further mechanical behaviour of fibre was investigated using a single fibre test with 5 kN cell load and tensile strength was found to be 45.61 ± 16.09 MPa for an average fibre diameter of 368.57 ± 50.47 μm. Meanwhile, moisture content analysis indicated a 6.00% moisture absorption rate of Pandanus amaryllifolius fibre. The thermogravimetric analysis justified the thermal stability of Pandanus amaryllifolius fibre up to 210 °C, which is within polymerization process temperature conditions. Overall, the finding shows that Pandanus amaryllifolius fibre may be used as alternative reinforcement particularly for a bio-based polymer matrix.

Preliminary Study of Alginates Extracted from Brown Algae (Sargassum sp.) Available in Madura Island as Composite Based Hydrogel Materials

2019 ◽  
Vol 964 ◽  
pp. 240-245 ◽  
Author(s):  
Amaliya Rasyida ◽  
Thalyta Rizkha Pradipta ◽  
Sigit Tri Wicaksono ◽  
Vania Mitha Pratiwi ◽  
Yeny Widya Rakhmawati
Keyword(s):  
Sodium Alginate ◽  
Brown Algae ◽  
Extraction Process ◽  
Composition Analysis ◽  
3D Printer ◽  
X Ray Diffraction ◽  
X Ray ◽  
3D Printed ◽  
Preliminary Study

Utilization of brown algae especially in Madura, where it’s close to Surabaya, only limited for food. This become a reference for developing and increasing the potential of this algae by extracting one of the ingredients, namely alginate. This paper deals with the characterization of sodium alginate extracted from sargassum sp. using modified-purified calcium routes. The extracted sodium alginate will be further used as composite hydrogel materials and compared with commercial sodium alginate. Hereafter, the synthesized composite is expected to be bio-ink for 3d printer. Chemical composition analysis were analyzed using X-Ray Fluorosense (XRF) followed by Fourier-transform infrared spectroscopy (FTIR) analysis to identify the functional group of composite and X-Ray Diffraction (XRD). Furthermore, viscosity bath is performed to compare the viscosity of extracted and commercial one. The result shows that modified-purified calcium routes in the extraction process of sodium alginate is desirable for improving their properties. Interestingly enough, with the goal of using it as bio-ink in 3d printed fabrication, the synthesized composite shows viscosity, 300 cSt, which meets the criteria for bio-ink in 3d printer.

scholarly journals Stability Analysis of a High Fibre Yield and Low Lignin Content “Thick Stem” Mutant in Tossa Jute (Corchorus olitoriusL.)

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Aninda Mandal ◽  
Animesh K. Datta
Keyword(s):  
Tensile Strength ◽  
Lignin Content ◽  
Fibre Diameter ◽  
Seed Viability ◽  
Pollen Grains ◽  
Single Fibre ◽  
Morphometric Traits ◽  
Stem Anatomy ◽  
Fibre Yield ◽  
Efficient Breeding

A “thick stem” mutant ofCorchorus olitoriusL. was induced at M2(0.50%, 4 h, EMS) and the true breeding mutant is assessed across generations (M5to M7) considering morphometric traits as well as SEM analysis of pollen grains and raw jute fibres, stem anatomy, cytogenetical attributes, and lignin content in relation to control. Furthermore, single fibre diameter and tensile strength are also analysed. The objective is to assess the stability of mutant for its effective exploration for raising a new plant type in tossa jute for commercial exploitation and efficient breeding. The mutant trait is monogenic recessive to normal. Results indicate that “thick stem” mutant is stable across generations (2n=14) with distinctive high seed and fibre yield and significantly low lignin content. Stem anatomy of the mutant shows significant enhancement in fibre zone, number of fibre pyramids and fibre bundles per pyramid, and diameter of fibre cell in relation to control. Moreover, tensile strength of mutant fibre is significantly higher than control fibre and the trait is inversely related to fibre diameter. However the mutant is associated with low germination frequency, poor seed viability, and high pollen sterility, which may be eliminated through mutational approach followed by rigorous selection and efficient breeding.

scholarly journals Very Fast and Accurate Procedure for the Characterization of Photovoltaic Panels from Datasheet Information

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Antonino Laudani ◽  
Francesco Riganti Fulginei ◽  
Alessandro Salvini ◽  
Gabriele Maria Lozito ◽  
Salvatore Coco
Keyword(s):  
Numerical Methods ◽  
Search Space ◽  
Extraction Process ◽  
Reduced Form ◽  
Photovoltaic Panels ◽  
Approximation Techniques ◽  
Computational Costs ◽  
Minimization Technique ◽  
Accurate Procedure

In recent years several numerical methods have been proposed to identify the five-parameter model of photovoltaic panels from manufacturer datasheets also by introducing simplification or approximation techniques. In this paper we present a fast and accurate procedure for obtaining the parameters of the five-parameter model by starting from its reduced form. The procedure allows characterizing, in few seconds, thousands of photovoltaic panels present on the standard databases. It introduces and takes advantage of further important mathematical considerations without any model simplifications or data approximations. In particular the five parameters are divided in two groups, independent and dependent parameters, in order to reduce the dimensions of the search space. The partitioning of the parameters provides a strong advantage in terms of convergence, computational costs, and execution time of the present approach. Validations on thousands of photovoltaic panels are presented that show how it is possible to make easy and efficient the extraction process of the five parameters, without taking care of choosing a specific solver algorithm but simply by using any deterministic optimization/minimization technique.

scholarly journals Fabrication and Characterization of Electrospun Poly(acrylonitrile-co-Methyl Acrylate)/Lignin Nanofibers: Effects of Lignin Type and Total Polymer Concentration

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 992
Author(s):  
Suchitha Devadas ◽  
Saja M. Nabat Al-Ajrash ◽  
Donald A. Klosterman ◽  
Kenya M. Crosson ◽  
Garry S. Crosson ◽  
...  
Keyword(s):  
Methyl Acrylate ◽  
Lignin Content ◽  
Polymer Concentration ◽  
Weight Ratio ◽  
Electrospun Nanofibers ◽  
Polymer Content ◽  
Blend Ratio ◽  
Blend Ratios ◽  
Poly Acrylonitrile

Lignin macromolecules are potential precursor materials for producing electrospun nanofibers for composite applications. However, little is known about the effect of lignin type and blend ratios with synthetic polymers. This study analyzed blends of poly(acrylonitrile-co-methyl acrylate) (PAN-MA) with two types of commercially available lignin, low sulfonate (LSL) and alkali, kraft lignin (AL), in DMF solvent. The electrospinning and polymer blend solution conditions were optimized to produce thermally stable, smooth lignin-based nanofibers with total polymer content of up to 20 wt % in solution and a 50/50 blend weight ratio. Microscopy studies revealed that AL blends possess good solubility, miscibility, and dispersibility compared to LSL blends. Despite the lignin content or type, rheological studies demonstrated that PAN-MA concentration in solution dictated the blend’s viscosity. Smooth electrospun nanofibers were fabricated using AL depending upon the total polymer content and blend ratio. AL’s addition to PAN-MA did not affect the glass transition or degradation temperatures of the nanofibers compared to neat PAN-MA. We confirmed the presence of each lignin type within PAN-MA nanofibers through infrared spectroscopy. PAN-MA/AL nanofibers possessed similar morphological and thermal properties as PAN-MA; thus, these lignin-based nanofibers can replace PAN in future applications, including production of carbon fibers and supercapacitors.

Optimization and characterization of flavonoids extracted from Cannabis sativa fibers

2021 ◽  
pp. 004051752110277
Author(s):  
Qilu Cui ◽  
Jiawei Li ◽  
Chongwen Yu
Keyword(s):  
Chemical Structure ◽  
Cannabis Sativa ◽  
Ethanol Concentration ◽  
Extraction Process ◽  
Test Results ◽  
Hemp Fiber ◽  
Hemp Fibers ◽  
Structure Surface ◽  
Degumming Process

In this paper, the extraction process of flavonoids from hemp fibers was studied. Response surface methodology (RSM) analysis of the extraction parameters indicated that optimized results would be ethanol concentration 76 vol.%, bath ratio 1:50, and reaction time 139 min; therefore, an optimal extraction rate of flavonoids of 0.2275% can be obtained. The chemical structure, surface morphology and element composition of flavonoid extracts were analyzed. The test results indicated that hemp extract contains flavonoids, which can be used to extract flavonoids from hemp fiber, so as to comprehensively develop hemp fiber and reduce the discharge of waste liquid in the traditional degumming process.

scholarly journals Enzymatic Extraction and Characterization of Pectin from Cocoa Pod Husks (Theobroma cacao L.) Using Celluclast® 1.5 L

Molecules ◽  
2021 ◽  
Vol 26 (5) ◽  
pp. 1473
Author(s):  
Licelander Hennessey-Ramos ◽  
Walter Murillo-Arango ◽  
Juliana Vasco-Correa ◽  
Isabel Cristina Paz Astudillo
Keyword(s):  
Acid Content ◽  
Galacturonic Acid ◽  
Extraction Process ◽  
Chemical Extraction ◽  
Enzymatic Extraction ◽  
Acid Yield ◽  
Physicochemical Features ◽  
Enzyme Dosage ◽  
Cocoa Pod Husks

Cocoa pod husks are a waste generated during the processing of cocoa beans. We aimed to explore the enzymatic extraction of pectin using cellulases. The extraction process was optimized using a central composite design (CCD) and analyzed by response surface methodology (RSM). The parameters optimized were feedstock concentration (%), enzyme dosage (µL/g), and time (h). Three dependent variables were studied: pectin yield (g/100 g dry husk) (R2 = 97.02), galacturonic acid content (g/100 g pectin) (R2 = 96.90), and galacturonic acid yield (g/100 g feedstock) (R2 = 95.35). The optimal parameters were 6.0% feedstock concentration, 40 µL g−1 of enzyme, and 18.54 h, conditions that produced experimentally a pectin yield of 10.20 g/100 g feedstock, 52.06 g galacturonic acid/100 g pectin, and a yield 5.31 g galacturonic acid/100 g feedstock. Using the chemical extraction method, a yield of 8.08 g pectin/100 g feedstock and a galacturonic acid content of 60.97 g/100 g pectin were obtained. Using assisted sonication, a pectin yield of 8.28 g/100 g feedstock and a galacturonic acid content of 42.77 g/100 g pectin were obtained. Enzymatically optimized pectin has rheological and physicochemical features typical of this biomaterial, which provides an interesting alternative for the valorization of cocoa husks.

scholarly journals Colored cotton wastes valuation through thermal and catalytic reforming of pyrolysis vapors (Py-GC/MS)

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Janduir Egito da Silva ◽  
Guilherme Quintela Calixto ◽  
Rodolfo Luiz Bezerra de Araújo Medeiros ◽  
Marcus Antônio de Freitas Melo ◽  
Dulce Maria de Araújo Melo ◽  
...  
Keyword(s):  
Lignin Content ◽  
Proximate Analysis ◽  
Catalytic Reforming ◽  
Pyrolysis Products ◽  
Heating Value ◽  
Colored Cotton ◽  
Benzene Toluene ◽  
Naturally Colored Cotton ◽  
Main Influence

AbstractThis study aims to analyze the products of the catalytic pyrolysis of naturally colored cotton residues, type BRS (seeds from Brazil), called BRS-Verde, BRS-Rubi, BRS-Topázio and BRS-Jade. The energy characterization of biomass was evaluated through ultimate and proximate analysis, higher heating value, cellulose, hemicellulose and lignin content, thermogravimetric analysis and apparent density. Analytical pyrolysis was performed at 500 °C in an analytical pyrolyzer from CDS Analytical connected to a gas chromatograph coupled to the mass spectrometer (GC/MS). The pyrolysis vapors were reformed at 300 and 500 °C through thermal and catalytic cracking with zeolites (ZSM-5 and HZSM-5). It has been noticed that pyrolysis vapor reforming at 500 °C promoted partial deoxygenation and cracking reactions, while the catalytic reforming showed better results for the product deoxygenation. The catalyst reforming of pyrolysis products, especially using HZSM-5 at 500 °C, promoted the formation of monoaromatics such as benzene, toluene, xylene and styrene, which are important precursors of polymers, solvents and biofuels. The main influence on the yields of these aromatic products is due to the catalytic activity of ZSM-5 favored by increased temperature that promotes cracking reactions due expanded zeolites channels.

Sign in / Sign up

Export Citation Format

Share Document