scholarly journals Spatial Baseline Optimization for Spaceborne Multistatic SAR Tomography Systems

Sensors ◽  
2019 ◽  
Vol 19 (9) ◽  
pp. 2106 ◽  
Author(s):  
Jiuchao Zhao ◽  
Anxi Yu ◽  
Yongsheng Zhang ◽  
Xiaoxiang Zhu ◽  
Zhen Dong
Keyword(s):  
Surface Deformation ◽  
Design Method ◽  
Geometric Model ◽  
Three Dimensional ◽  
Optimization Method ◽  
Deformation Measurement ◽  
Experimental Simulation ◽  
Baseline Design ◽  
Imaging Performance ◽  
The Impact

Spaceborne multistatic synthetic aperture radar (SAR) tomography (SMS-TomoSAR) systems take full advantage of the flexible configuration of multistatic SAR in the space, time, phase, and frequency dimensions, and simultaneously achieve high-precision height resolution and low-deformation measurement of three-dimensional ground scenes. SMS-TomoSAR currently poses a series of key issues to solve, such as baseline optimization, spatial transmission error estimation and compensation, and the choice of imaging algorithm, which directly affects the performance of height-dimensional imaging and surface deformation measurement. This paper explores the impact of baseline distribution on height-dimensional imaging performance for the baseline optimization issue, and proposes a feasible baseline optimization method. Firstly, the multi-base multi-pass baselines of an SMS-TomoSAR system are considered equivalent to a group of multi-pass baselines from monostatic SAR. Secondly, we establish the equivalent baselines as a symmetric-geometric model to characterize the non-uniform characteristic of baseline distribution. Through experimental simulation and model analysis, an approximately uniform baseline distribution is shown to have better SMS-TomoSAR imaging performance in the height direction. Further, a baseline design method under uniform-perturbation sampling with Gaussian distribution error is proposed. Finally, the imaging performance of different levels of perturbation is compared, and the maximum baseline perturbation allowed by the system is given.

scholarly journals Lightweight and maintainable rotary-wing UAV frame from configurable design to detailed design

2021 ◽  
Vol 13 (7) ◽  
pp. 168781402110349
Author(s):  
Huiqiang Guo ◽  
Mingzhe Li ◽  
Pengfei Sun ◽  
Changfeng Zhao ◽  
Wenjie Zuo ◽  
...  
Keyword(s):  
Design Method ◽  
Geometric Model ◽  
Optimization Method ◽  
Frame Structure ◽  
Manufacturing Cost ◽  
Detailed Design ◽  
High Manufacturing Cost ◽  
The Military ◽  
Rotary Wing ◽  
Novel Design

Rotary-wing unmanned aerial vehicles (UAVs) are widespread in both the military and civilian applications. However, there are still some problems for the UAV design such as the long design period, high manufacturing cost, and difficulty in maintenance. Therefore, this paper proposes a novel design method to obtain a lightweight and maintainable UAV frame from configurable design to detailed design. First, configurable design is implemented to determine the initial design domain of the UAV frame. Second, topology optimization method based on inertia relief theory is used to transform the initial geometric model into the UAV frame structure. Third, process design is considered to improve the manufacturability and maintainability of the UAV frame. Finally, dynamic drop test is used to validate the crashworthiness of the UAV frame. Therefore, a lightweight UAV frame structure composed of thin-walled parts can be obtained and the design period can be greatly reduced via the proposed method.

scholarly journals Multiscale, thermomechanical topology optimization of self-supporting cellular structures for porous injection molds

2019 ◽  
Vol 25 (9) ◽  
pp. 1482-1492
Author(s):  
Tong Wu ◽  
Andres Tovar
Keyword(s):  
Topology Optimization ◽  
Mechanical Performance ◽  
Mechanical Load ◽  
Design Method ◽  
Three Dimensional ◽  
Optimization Method ◽  
Cellular Structures ◽  
Injection Mold ◽  
Computationally Efficient ◽  
Content Type

Purpose This paper aims to establish a multiscale topology optimization method for the optimal design of non-periodic, self-supporting cellular structures subjected to thermo-mechanical loads. The result is a hierarchically complex design that is thermally efficient, mechanically stable and suitable for additive manufacturing (AM). Design/methodology/approach The proposed method seeks to maximize thermo-mechanical performance at the macroscale in a conceptual design while obtaining maximum shear modulus for each unit cell at the mesoscale. Then, the macroscale performance is re-estimated, and the mesoscale design is updated until the macroscale performance is satisfied. Findings A two-dimensional Messerschmitt Bolkow Bolhm (MBB) beam withstanding thermo-mechanical load is presented to illustrate the proposed design method. Furthermore, the method is implemented to optimize a three-dimensional injection mold, which is successfully prototyped using 420 stainless steel infiltrated with bronze. Originality/value By developing a computationally efficient and manufacturing friendly inverse homogenization approach, the novel multiscale design could generate porous molds which can save up to 30 per cent material compared to their solid counterpart without decreasing thermo-mechanical performance. Practical implications This study is a useful tool for the designer in molding industries to reduce the cost of the injection mold and take full advantage of AM.

scholarly journals New Design Procedure of Transtibial ProsthesisBed Stump Using Topological Optimization Method

Symmetry ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 1837 ◽  
Author(s):  
Martin Sotola ◽  
David Stareczek ◽  
David Rybansky ◽  
Jiri Prokop ◽  
Pavel Marsalek
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Design Procedure ◽  
Optimization Method ◽  
Topological Optimization ◽  
Element Analysis ◽  
Current Application ◽  
Transtibial Prosthesis ◽  
Walking Biomechanics ◽  
The Impact

This paper presents a new design procedure for production of a transtibial prosthesis bed stump by three-dimensional (3D) printing with topological optimization. The suggested procedure combines the medical perspective with finite element analysis and facilitates regaining the symmetry in patients with transtibial prosthesis, which leads to life improvement. The particular focus of the study is the weight reduction of the lower part of the bed stump, while taking into account its stiffness and load-bearing capacity. The first part of the work deals with the analysis of the subject geometry of the bed stump, which is usually oversized in terms of the weight and stiffness that are necessary for the current application. In the second part, an analysis of walking biomechanics with a focus on the impact and rebound phases is presented. Based on the obtained information, a spatial model of the lower part of the bed stump is proposed in the third phase, in which the finite element method is described. In the fourth part, the topological optimization method is used for reducing the structure weight. In the last part, the results of the designed model are analyzed. Finally, the recommendations for the settings of the method are presented. The work is based on the practical industry requirements, and the obtained results will be reflected in the design of new types of transtibial prosthesis.

scholarly journals Ultra-High Early Strength Cementitious Grout Suitable for Additive Manufacturing Applications Fabricated by Using Graphene Oxide and Viscosity Modifying Agents

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2900
Author(s):  
Alyaa Mohammed ◽  
Nihad Tareq Khshain Al-Saadi
Keyword(s):  
Graphene Oxide ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Design Method ◽  
Three Dimensional ◽  
Cementitious Materials ◽  
Fresh Properties ◽  
Manufacturing Applications ◽  
Mechanical Strengths ◽  
The Impact

One of the considerable challenges in the design of cementitious mixtures for additive manufacturing/three-dimensional (3D) printing applications is achieving both suitable fresh properties and significant mechanical strengths. This paper presents the use of graphene oxide (GO) as a promising nano reinforcement material with the potential to improve the printing feasibility and quality of a 3D printed cementitious matrix. Additionally, in this study, a viscosity modifying agent (VMA) was employed as a chemical additive to attain the required consistency and flow. The printed mixture was fabricated using various cementitious materials and waste materials. This study investigated the impact of GO and VMA on the enhancement of the 3D printing of cementitious composites through several tests. A flow test was conducted using the flow table test. The results showed a high fluidity and practical consistency, which are essential for nozzle pumping and accurateness in printed shapes. Furthermore, the bleeding test showed minimal bleeding up to hardening, and a considerable self-cleaning ability was noted during handling when conducting examinations of fresh properties. For hardened properties, the mechanical strengths were exceptionally high, especially at early ages, which is crucial for the stability of sequence layers of printed composites. The tensile strengths were 3.77, 10.5, 13.35, and 18.83 MPa at 1, 3, 7, and 28 days, respectively, and the compressive strengths were 25.1, 68.4, 85.6, and 125.4 MPa at 1, 3, 7, and 28 days, respectively. The test results showed the effectiveness of the fabricated cementitious mixture design method for meeting the requirements for 3D concrete printing applications.

An experience-independent inverse design optimization method of compressor cascade airfoil

2019 ◽  
Vol 233 (4) ◽  
pp. 431-442 ◽  
Author(s):  
Yujie Zhu ◽  
Yaping Ju ◽  
Chuhua Zhang
Keyword(s):  
Design Optimization ◽  
Design Method ◽  
Three Dimensional ◽  
Optimal Solution ◽  
Leading Edge ◽  
Optimization Method ◽  
Inverse Design ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Inverse Design Method

Most of the inverse design methods of turbomachinery experience the shortcoming where the target aerodynamic parameters need to be manually specified depending on the designers’ experience and insight, making the design result aleatory and even deviated from the real optimal solution. To tackle this problem, an experience-independent inverse design optimization method is proposed and applied to the redesign of a compressor cascade airfoil in this study. The experience-independent inverse design optimization method can automatically obtain the target pressure distribution along the cascade airfoil through the genetic algorithm, rather than through the manual specification approach. The shape of cascade airfoil is then solved by the adjoint method. The effectiveness of the experience-independent inverse design optimization method is demonstrated by two inverse design cases of the compressor cascade airfoil, i.e. the inverse design of only the suction surface and the inverse design of both the suction and pressure surfaces. The results show that the proposed inverse design method is capable of significantly improving the aerodynamic performance of the compressor cascade. At the examined flow condition, a thin airfoil profile is beneficial to flow accelerations near the leading edge and flow separation avoidance near the trailing edge. The proposed inverse design method is quite generic and can be extended to the three-dimensional inverse design of advanced compressor blades.

scholarly journals Ultra-thin fluorocarbon foils optimise multiscale imaging of three-dimensional native and optically cleared specimens

2019 ◽  
Author(s):  
Katharina Hötte ◽  
Michael Koch ◽  
Lotta Hof ◽  
Marcel Tuppi ◽  
Till Moreth ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Light Sheet ◽  
Optical Quality ◽  
Immersion Medium ◽  
Specimen Holder ◽  
Time Period ◽  
Optimal Resolution ◽  
Full Separation ◽  
Imaging Performance ◽  
The Impact

AbstractIn three-dimensional light microscopy, the heterogeneity of the optical density in a specimen ultimately limits the achievable penetration depth and hence the three-dimensional resolution. The most direct approach to reduce aberrations, improve the contrast, and achieve an optimal resolution is minimizing the impact of changes of the refractive index along an optical path. Many light sheet fluorescence microscopes operate with a large chamber that contains an aqueous immersion medium and an inner specimen holder that contains the specimen embedded in a possibly entirely different non-aqueous medium. In order to minimize the impact of the specimen holder on the optical quality, we use multi-facetted cuvettes fabricated with vacuum-formed ultra-thin fluorocarbon (FEP) foils The ultra-thin FEP-foil cuvettes have a wall thickness of about 12 µm. They are resilient to fluidic exchanges, durable, mechanically stable and yet flexible.We confirm the improved imaging performance of ultra-thin FEP-foil cuvettes with excellent quality images of whole organs, thick tissue sections and dense organoid clusters. The cuvettes outperform many other sample-mounting techniques in terms of full separation of the specimen from the immersion medium, compatibility with aqueous and organic clearing media, quick specimen mounting without hydrogel embedding, as well as their applicability for multiple-view imaging and automated segmentation. Additionally, we show that ultra-thin FEP foil cuvettes are suitable for seeding and growing organoids over a time period of at least ten days. The ultra-thin cuvettes allow the fixation and staining of the specimens inside the holder, preserving the delicate morphology of e.g. fragile, mono-layered three-dimensional organoids.

scholarly journals Ultra-thin fluorocarbon foils optimise multiscale imaging of three-dimensional native and optically cleared specimens

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Katharina Hötte ◽  
Michael Koch ◽  
Lotta Hof ◽  
Marcel Tuppi ◽  
Till Moreth ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Light Sheet ◽  
Optical Quality ◽  
Tissue Sections ◽  
Immersion Medium ◽  
Time Period ◽  
Optimal Resolution ◽  
Full Separation ◽  
Imaging Performance ◽  
The Impact

AbstractIn three-dimensional light microscopy, the heterogeneity of the optical density in a specimen ultimately limits the achievable penetration depth and hence the three-dimensional resolution. The most direct approach to reduce aberrations, improve the contrast and achieve an optimal resolution is to minimise the impact of changes of the refractive index along an optical path. Many implementations of light sheet fluorescence microscopy operate with a large chamber filled with an aqueous immersion medium and a further inner container with the specimen embedded in a possibly entirely different non-aqueous medium. In order to minimise the impact of the latter on the optical quality of the images, we use multi-facetted cuvettes fabricated from vacuum-formed ultra-thin fluorocarbon (FEP) foils. The ultra-thin FEP-foil cuvettes have a wall thickness of about 10–12 µm. They are impermeable to liquids, but not to gases, inert, durable, mechanically stable and flexible. Importantly, the usually fragile specimen can remain in the same cuvette from seeding to fixation, clearing and observation, without the need to remove or remount it during any of these steps. We confirm the improved imaging performance of ultra-thin FEP-foil cuvettes with excellent quality images of whole organs such us mouse oocytes, of thick tissue sections from mouse brain and kidney as well as of dense pancreas and liver organoid clusters. Our ultra-thin FEP-foil cuvettes outperform many other sample-mounting techniques in terms of a full separation of the specimen from the immersion medium, compatibility with aqueous and organic clearing media, quick specimen mounting without hydrogel embedding and their applicability for multiple-view imaging and automated image segmentation. Additionally, we show that ultra-thin FEP foil cuvettes are suitable for seeding and growing organoids over a time period of at least ten days. The new cuvettes allow the fixation and staining of specimens inside the holder, preserving the delicate morphology of e.g. fragile, mono-layered three-dimensional organoids.

Design Method for Inner Structure of Injection Mold Fabricated by Metal Laser Sintering

2012 ◽  
Vol 6 (5) ◽  
pp. 584-590 ◽  
Author(s):  
Hiroshi Koresawa ◽  
◽  
Hirofumi Fukumaru ◽  
Michio Kojima ◽  
Jun Iwanaga ◽  
...  
Keyword(s):  
Mechanical Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Design Method ◽  
Selective Laser Sintering ◽  
Three Dimensional ◽  
Optimization Method ◽  
Laser Sintering ◽  
Sintered Body ◽  
Sintering Process

This paper discusses design methods for the internal structure of molds used in production utilizing metal laser sintering combined with high speedmilling which selectively sinters metal powder to form a three dimensional mold. This milling technique is characterized by the fact that the selective laser sintering process and milling process are carried out in alternating sequence, achieving the level of processing accuracy demanded of mold production. In addition, in the selective laser sintering process, because the mechanical strength of the sintered body (Young’s Modulus) is variable, suitable interior structures that consider dynamic conditions are expected. However, in the current state of design, this structure is determined experimentally, and there is a high possibility of incurring unnecessary production time and high costs. In this paper, we investigate a method that incorporates an optimization method using stress that occurs within the structure interior, obtains the interior topological structure as a Young’s Modulus distribution, and designs a suitable interior structure using this distribution. As a result of investigation using numerical analysis, we obtained a structure that reduces the volume of the sintered body, having high mechanical strength in comparison with a conventional structure while improving structural rigidity.

Motion Analysis of McKibben Type Pneumatic Rubber Artificial Muscle with Finite Element Method

2014 ◽  
Vol 8 (2) ◽  
pp. 147-158 ◽  
Author(s):  
Takashi Nozaki ◽  
◽  
Toshiro Noritsugu ◽  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
3D Model ◽  
Design Method ◽  
Three Dimensional ◽  
Artificial Muscle ◽  
Optimization Method ◽  
Artificial Muscles ◽  
3D Finite Element ◽  
Quantitative Design

This study aims to use three-dimensional (3D) Finite Element Modeling (FEM) to establish a quantitative design optimization method forMcKibben-type pneumatic rubber artificial muscle. First, a simple 3D model that does not account for the friction between the tube and the fiber braid strands and or that between the strands themselves is developed. The model is validated through experimentation, and the usefulness of the model is examined. With this model, the effects of various parameters, e.g., the braid angle, on the operation of the artificial muscle is investigated. It is found that the characteristics of the artificial muscle can be predicted. Thus, the proposed analysis may be a useful design method for braided artificial muscles.

scholarly journals Optimization of Meridional Flow Channel Design of Pump Impeller

2004 ◽  
Vol 10 (2) ◽  
pp. 115-119 ◽  
Author(s):  
Sunao Miyauchi ◽  
Hironori Horiguchi ◽  
Jun-ichirou Fukutomi ◽  
Akihiro Takahashi
Keyword(s):  
Design Method ◽  
Three Dimensional ◽  
Optimization Method ◽  
Meridional Flow ◽  
Flow Channel ◽  
Design Parameters ◽  
Channel Design ◽  
Pump Impeller ◽  
Circulation Distribution ◽  
Meridional Shape

The meridional flow channel design of a pump impeller affects its performance. However, since so many design parameters exist, a new design method is proposed in which a meridional and blade-to-blade flow channel is designed by the parallel use of the circulation distribution provided by the designer. Thus, an optimization method was used to design an axis-symmetrical meridional flow channel from the circulation distribution. In addition, the inverse design method proposed by Zangeneh et al. (1996) was employed to design a three-dimensional blade-to-blade flow channel from the circulation distribution and the optimized meridional shape. In this article, a few design examples and these Computational Fluid Dynamics (CFD) validations are also given.

Sign in / Sign up

Export Citation Format

Share Document