scholarly journals Modeling of the MET Sensitive Element Conversion Factor on the Intercathode Distance

Sensors ◽  
2020 ◽  
Vol 20 (18) ◽  
pp. 5146
Author(s):  
Maksim Ryzhkov ◽  
Vadim Agafonov
Keyword(s):  
High Frequency ◽  
Sensitive Element ◽  
Conversion Factor ◽  
Conversion Coefficient ◽  
Low Frequency ◽  
Frequency Region ◽  
Frequency Range ◽  
System Parameters ◽  
A Cell ◽  
Transforming Cell

MET sensors for measuring motion parameters are used in many scientific and technical fields. Meanwhile, the geometries of the transforming cell applied practically are far from optimal, and the influence of many geometric parameters on the sensitivity has not been studied. These parameters include the intercathode distance in a four-electrode conversion cell. In this paper, a mathematical model that allows calculating the behavior of the conversion coefficient depending on the frequency for a cell with flat electrodes at different intercathode distances is constructed. The stationary current is shown to decrease monotonically with the decreasing intercathode distance at the constancy of other system parameters. At the same time, the signal current decreases in the low-frequency region and increases in the high-frequency range. Taking into account the results obtained, practically speaking, it is advisable to reduce the intercathode distance to the technologically possible minimum, which makes the frequency response more uniform and reduces the current consumed by the sensitive element.

Anderson-Stuart Model to Analyze AC and DC Conductivity of Lithium Zinc-Silicate Glass / Glass-Ceramics

2007 ◽  
Vol 280-283 ◽  
pp. 919-924
Author(s):  
M.S. Jogad ◽  
V.K. Shrikhande ◽  
A.H. Dyama ◽  
L.A. Udachan ◽  
Govind P. Kothiyal
Keyword(s):  
High Frequency ◽  
Glass Ceramics ◽  
Low Frequency ◽  
Frequency Region ◽  
Dc Conductivity ◽  
Frequency Range ◽  
High Frequency Region ◽  
Dc Conductivities ◽  
Conductivity Variation ◽  
Different Temperatures

AC and DC conductivities have been measured by using the real (e¢) and imaginary (e¢¢) parts of the dielectric constant data of glass and glass-ceramics (GC) at different temperatures in the rage 297-642K and in the frequency range 100 Hz to 10 MHz. Using Anderson –Stuart model, we have calculated the activation energy, which is observed to be lower than that of the DC conductivity. The analysis for glass/glass-ceramics indicates that the conductivity variation with frequency exhibits an initial linear region followed by nonlinear region with a maximum in the high-frequency region. The observed frequency dependence of ionic conductivity has been analyzed within the extended Anderson–Stuart model considering both the electrostatic and elastic strain terms. In glass/glassceramic the calculations based on the Anderson-Stuart model agree with the experimental observations in the low frequency region but at higher frequencies there is departure from measured data.

On-Board Aircraft Engine Bearing Prognostics: Enveloping or FFT Analysis?

2009 ◽  
Author(s):  
Hai Qiu ◽  
Huageng Luo ◽  
Neil Eklund
Keyword(s):  
Spectrum Analysis ◽  
High Frequency ◽  
Characteristic Frequency ◽  
Low Frequency ◽  
Aircraft Engine ◽  
Frequency Region ◽  
Data Sampling ◽  
Frequency Range ◽  
Bearing Defect ◽  
Bearing Characteristic

Roller bearing prognosis requires the detection of a bearing defect signature in the earliest possible stage in order to avoid a minor or catastrophic mechanical failure. Defects can occur in any of the bearing parts, inner and outer race, cage and rolling elements. It is possible to identify the defective component of the bearing based on the specific vibration frequencies that are excited. However, the pattern of vibration spectrum changes as the bearing deteriorates through different stages. Depending on which failure stage the bearing is in, different techniques are required to find fault signatures in different frequency ranges. Techniques such as enveloping analysis that works in the high frequency region require higher data sampling rates and therefore more expensive data acquisition hardware than techniques conducted in low frequency region. This paper compares two popular rolling element bearing diagnostics techniques — spectrum analysis in the bearing characteristic frequency range and enveloping analysis in the high frequency range — using aircraft engine test rig data. The techniques are compared both in terms of the time of detection and data sampling requirement; this analysis provides guidance for technology adoption in future field deployment. Results demonstrate that enveloping analysis is able to detect bearing defects much earlier than the spectrum analysis, but it requires a higher data sampling rate. The bearing defect characteristic frequency is detectable in low frequency spectrum only in the late stage of the failure and it is contaminated by other harmonics such as shaft unbalance. From a practical perspective, the final choice of the technology adopted for deployment should be based on an analysis of hardware requirements and tolerance of detection latency.

Dielectric Spectrum of CaCu3Ti4012 from the Giant Permittivity to its Negative Values

2013 ◽  
Vol 705 ◽  
pp. 52-55 ◽  
Author(s):  
Yurii Kabirov ◽  
Victor Gavrilyachenko ◽  
Evgeni Panchenko ◽  
Evgeni Milov ◽  
Anatoly Klenushkin
Keyword(s):  
Activation Energy ◽  
High Frequency ◽  
Low Frequency ◽  
Frequency Region ◽  
Dielectric Spectrum ◽  
Ceramic Technology ◽  
High Frequency Range ◽  
Frequency Range ◽  
One Step

The dielectric spectrum of CaCu3Ti4O12samples prepared by traditional "one step" ceramic technology is analyzed. It is established that the characteristic Debye-type dispersion with an activation energy 0, 075 eV manifests in the high-frequency range (f ~ 106Hz). In the low-frequency region (f< 102Hz) a transition from giant permittivity values to its negative values is detected in some samples. Conditions for such transition are discussed.

Evaluation of Special Hearing Aids for Deaf Children

1971 ◽  
Vol 36 (4) ◽  
pp. 527-537 ◽  
Author(s):  
Norman P. Erber
Keyword(s):  
Hearing Aids ◽  
High Frequency ◽  
Hearing Aid ◽  
Low Frequency ◽  
Acoustic Stimulation ◽  
Deaf Children ◽  
Frequency Range ◽  
Frequency Limit ◽  
Unpublished Studies ◽  
Published Research

Two types of special hearing aid have been developed recently to improve the reception of speech by profoundly deaf children. In a different way, each special system provides greater low-frequency acoustic stimulation to deaf ears than does a conventional hearing aid. One of the devices extends the low-frequency limit of amplification; the other shifts high-frequency energy to a lower frequency range. In general, previous evaluations of these special hearing aids have obtained inconsistent or inconclusive results. This paper reviews most of the published research on the use of special hearing aids by deaf children, summarizes several unpublished studies, and suggests a set of guidelines for future evaluations of special and conventional amplification systems.

scholarly journals An Improved Time Integration Method Based on Galerkin Weak Form with Controllable Numerical Dissipation

2021 ◽  
Vol 11 (4) ◽  
pp. 1932
Author(s):  
Weixuan Wang ◽  
Qinyan Xing ◽  
Qinghao Yang
Keyword(s):  
High Frequency ◽  
Integration Method ◽  
Time Integration ◽  
Low Frequency ◽  
Weak Form ◽  
High Accuracy ◽  
Numerical Dissipation ◽  
Frequency Range ◽  
Time Integration Method ◽  
Numerical Damping

Based on the newly proposed generalized Galerkin weak form (GGW) method, a two-step time integration method with controllable numerical dissipation is presented. In the first sub-step, the GGW method is used, and in the second sub-step, a new parameter is introduced by using the idea of a trapezoidal integral. According to the numerical analysis, it can be concluded that this method is unconditionally stable and its numerical damping is controllable with the change in introduced parameters. Compared with the GGW method, this two-step scheme avoids the fast numerical dissipation in a low-frequency range. To highlight the performance of the proposed method, some numerical problems are presented and illustrated which show that this method possesses superior accuracy, stability and efficiency compared with conventional trapezoidal rule, the Wilson method, and the Bathe method. High accuracy in a low-frequency range and controllable numerical dissipation in a high-frequency range are both the merits of the method.

scholarly journals A Compact Four-Port Coplanar Antenna Based on an Excitation Switching Reconfigurable Mechanism for Cognitive Radio Applications

2019 ◽  
Vol 9 (15) ◽  
pp. 3157 ◽  
Author(s):  
O ◽  
Jin ◽  
Choi
Keyword(s):  
Cognitive Radio ◽  
High Frequency ◽  
Coplanar Waveguide ◽  
Low Frequency ◽  
Loop Antenna ◽  
Ultra Wideband ◽  
Frequency Range ◽  
Uwb Antenna ◽  
High Isolation ◽  
Loop Antennas

In this paper, we propose a compact four-port coplanar antenna for cognitive radio applications. The proposed antenna consists of a coplanar waveguide (CPW)-fed ultra-wideband (UWB) antenna and three inner rectangular loop antennas. The dimensions of the proposed antenna are 42 mm × 50 mm × 0.8 mm. The UWB antenna is used for spectrum sensing and fully covers the UWB spectrum of 3.1–10.6 GHz. The three loop antennas cover the UWB frequency band partially for communication purposes. The first loop antenna for the low frequency range operates from 2.96 GHz to 5.38 GHz. The second loop antenna is in charge of the mid band from 5.31 GHz to 8.62 GHz. The third antenna operates from 8.48 GHz to 11.02 GHz, which is the high-frequency range. A high isolation level (greater than 17.3 dB) is realized among the UWB antenna and three loop antennas without applying any additional decoupling structures. The realized gains of the UWB antenna and three loop antennas are greater than 2.7 dBi and 1.38 dBi, respectively.

Electromagnetic Property of La0.7Sr0.3MnO3/Ag Composite at High Frequency

2015 ◽  
Vol 655 ◽  
pp. 182-185
Author(s):  
Ke Lan Yan ◽  
Run Hua Fan ◽  
Min Chen ◽  
Kai Sun ◽  
Xu Ai Wang ◽  
...  
Keyword(s):  
High Frequency ◽  
Single Phase ◽  
Low Frequency ◽  
Electromagnetic Property ◽  
High Frequency Range ◽  
Frequency Range ◽  
Free Electron Concentration ◽  
Theoretical Simulation ◽  
Electrical And Magnetic Properties ◽  
Three Phase

The phase structure, and electrical and magnetic properties of La0.7Sr0.3MnO3(LSMO)-xAg (xis the mole ratio,x=0, 0.3, 0.5) composite were investigated. It is found that the sample withx=0 is single phase; the samples withx=0.3 and 0.5 present three phase composite structure of the manganese oxide and Ag. With the increasing of Ag content, the grain size of the samples increases and the grain boundaries transition from fully faceted to partially faceted. The permittivity of spectrum (10 MHz - 1 GHz) and the theoretical simulation reveal that the plasma frequencyfpincrease with Ag content, due to the increasing of free electron concentration, which is further supported by the enhancement of conductivity. While for the permeability (μr'), theμr'decrease with the increasing of Ag content at low frequency range (f< 20 MHz), while at the relative high frequency range (f> 300 MHz), theμr'increased with Ag content. Therefore, the introduction of elemental Ag resulted in a higherμr'at the relative high frequency range.

Shallow subsurface mapping by electromagnetic sounding in the 300 kHz to 30 MHz range: Model studies and prototype system assessment

Geophysics ◽  
1994 ◽  
Vol 59 (8) ◽  
pp. 1201-1210 ◽  
Author(s):  
Duff C. Stewart ◽  
Walter L. Anderson ◽  
Thomas P. Grover ◽  
Victor F. Labson
Keyword(s):  
Dielectric Permittivity ◽  
High Frequency ◽  
Low Frequency ◽  
Computer Programs ◽  
Thin Layers ◽  
Depth Range ◽  
Frequency Range ◽  
Model Studies ◽  
New Instrument ◽  
Displacement Currents

A new instrument designed for frequency‐domain sounding in the depth range 0–10 m uses short coil spacings of 5 m or less and a frequency range of 300 kHz to 30 MHz. In this frequency range, both conduction currents (controlled by electrical conductivity) and displacement currents (controlled by dielectric permittivity) are important. Several surface electromagnetic survey systems commonly used (generally with frequencies less than 60 kHz) are unsuitable for detailed investigation of the upper 5 m of the earth or, as with ground‐penetrating radar, are most effective in relatively resistive environments. Most computer programs written for interpretation of data acquired with the low‐frequency systems neglect displacement currents, and are thus unsuited for accurate high‐frequency modeling and interpretation. New forward and inverse computer programs are described that include displacement currents in layered‐earth models. The computer programs and this new instrument are used to evaluate the effectiveness of shallow high‐frequency soundings based on measurement of the tilt angle and the ellipticity of magnetic fields. Forward model studies indicate that the influence of dielectric permittivity provides the ability to resolve thin layers, especially if the instrument frequency range can be extended to 50 MHz. Field tests of the instrument and the inversion program demonstrate the potential for detailed shallow mapping wherein both the resistivity and the dielectric permittivity of layers are determined. Although data collection and inversion are much slower than for low‐frequency methods, additional information is obtained inasmuch as there usually is a permittivity contrast as well as a resistivity contrast at boundaries between different materials. Determination of dielectric permittivity is particularly important for hazardous waste site characterization because the presence of some contaminants may have little effect on observed resistivity but a large effect on observed permittivity.

How word frequency affects morphological processing in monolinguals and bilinguals

2003 ◽  
Vol 6 (3) ◽  
pp. 213-225 ◽  
Author(s):  
MINNA LEHTONEN ◽  
MATTI LAINE
Keyword(s):  
High Frequency ◽  
Low Frequency ◽  
Morphological Processing ◽  
Decision Task ◽  
Frequency Range ◽  
Medium Frequency ◽  
Word Forms ◽  
Full Form ◽  
Differential Pattern ◽  
Complex Words

The present study investigated processing of morphologically complex words in three different frequency ranges in monolingual Finnish speakers and Finnish-Swedish bilinguals. By employing a visual lexical decision task, we found a differential pattern of results in monolinguals vs. bilinguals. Monolingual Finns seemed to process low frequency and medium frequency inflected Finnish nouns mostly by morpheme-based recognition but high frequency inflected nouns through full-form representations. In contrast, bilinguals demonstrated a processing delay for all inflections throughout the whole frequency range, suggesting decomposition for all inflected targets. This may reflect different amounts of exposure to the word forms in the two groups. Inflected word forms that are encountered very frequently will acquire full-form representations, which saves processing time. However, with the lower rates of exposure, which characterize bilingual individuals, full-form representations do not start to develop.

Effect of rail pad stiffness on the wheel/rail force intensity in a railway slab track with short-wave irregularity

2019 ◽  
Vol 233 (10) ◽  
pp. 1038-1049 ◽  
Author(s):  
Amin Khajehdezfuly
Keyword(s):  
High Frequency ◽  
Critical Speed ◽  
Concrete Slab ◽  
Low Frequency ◽  
Short Wave ◽  
Vehicle Speed ◽  
Frequency Range ◽  
Slab Track ◽  
High Frequency Excitation ◽  
Frequency Excitation

In this paper, a two-dimensional numerical model is developed to investigate the effect of rail pad stiffness on the wheel/rail force in a slab track with harmonic irregularity. The model consists of a vehicle, nonlinear Hertz spring, rail, rail pad, concrete slab, resilient layer, concrete base, and subgrade. The rail is simulated using the Timoshenko beam element for considering the effects of high-frequency excitation produced by short-wave irregularity. The results obtained from the model are compared with those available in the literature and from the field to prove the validity of the model. Through a parametric study, the effect of variations in rail pad stiffness, vehicle speed, and harmonic irregularity on the wheel/rail force is investigated. For the slab track without any irregularity, the wheel/rail force is at maximum when the vehicle speed reaches the critical speed. As the rail pad stiffness increases, the critical speed increases. When the amplitude of irregularity is high, wheel jumping phenomenon may occur. In this situation, as the vehicle speed and rail pad stiffness are increased, the dynamic wheel/rail force is increased. In the low-frequency range, the wheel/rail force increases as the rail pad stiffness increases. In the high-frequency range, the wheel/rail force increases as the rail pad stiffness is decreased.

Sign in / Sign up

Export Citation Format

Share Document