scholarly journals Clay-Based Products Sustainable Development: Some Applications

2021 ◽  
Vol 13 (3) ◽  
pp. 1364
Author(s):  
Michele La Noce ◽  
Alessandro Lo Faro ◽  
Gaetano Sciuto
Keyword(s):  
Sustainable Development ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Basalt Fibers ◽  
Future Studies ◽  
Clay Bricks ◽  
Brick Powder ◽  
Alkaline Resistance ◽  
Raw Earth

Clay has a low environmental impact and can develop into many different products. The research presents two different case studies. In the first, the clay is the binder of raw earth doughs in order to produce clay-bricks. We investigate the effects of natural fibrous reinforcements (rice straws and basalt fibers) in four different mixtures. From the comparison with a mix without reinforcements, it is possible to affirm that the 0.40% of basalt fibers reduce the shrinkage by about 25% and increase the compressive strength by about 30%. Future studies will focus on identifying the fibrous effects on tensile strength and elastic modulus, as well as the optimal percentage of fibers. In the second study, the clay, in form of brick powder (“cocciopesto”), gives high alkaline resistance and breathability performance, as well as rendering and color to the plaster. The latter does not have artificial additives. The plaster respects the cultural instance of the original building. The research underlines how the use of a local (and traditional) material such as clay can be a promoter of sustainability in the contemporary building sector. Future studies must investigate further possible uses of clay as well as a proper regulatory framework.

scholarly journals Effect of Waste Clay Brick Powder on Physical and Mechanical Properties of Cement Paste

2021 ◽  
Vol 15 (1) ◽  
pp. 370-380
Author(s):  
David Sinkhonde ◽  
Richard Ocharo Onchiri ◽  
Walter Odhiambo Oyawa ◽  
John Nyiro Mwero
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Setting Time ◽  
Partial Replacement ◽  
Clay Brick ◽  
X Ray ◽  
Cement Replacement ◽  
Clay Bricks ◽  
Brick Powder ◽  
Scanning Electron

Background: Investigations on the use of waste clay brick powder in concrete have been extensively conducted, but the analysis of waste clay brick powder effects on cement paste is limited. Materials and Methods: This paper discusses the effects of waste clay brick powder on cement paste. Fragmented clay bricks were grounded in the laboratory using a ball mill and incorporated into cementitious mixes as partial replacement of Ordinary Portland Cement. Workability, consistency, setting time, density and compressive strength properties of paste mixes were investigated to better understand the impact of waste clay brick powder on the cementitious paste. Four cement replacement levels of 2.5%, 5%, 7.5% and 10% were evaluated in comparison with the control paste. The chemical and mineral compositions were evaluated using X-Ray Fluorescence and X-Ray Diffractometer, respectively. The morphology of cement and waste clay brick powder was examined using a scanning electron microscope. Results: The investigation of workability exhibited a reduction of slump attributed to the significant addition of waste clay brick powder into the cementitious mixes, and it was concluded that waste clay brick powder did not significantly influence the density of the mixes. In comparison with the control paste, increased values of consistency and setting time of cement paste containing waste clay brick powder confirmed the information available in the literature. Conclusion: Although waste clay brick powder decreased the compressive strength of cement paste, 5% partial cement replacement with waste clay brick powder was established as an optimum percentage for specimens containing waste clay brick powder following curing periods of 7 and 28 days. Findings of chemical composition, mineral composition and scanning electron microscopy of waste clay brick powder demonstrated that when finely ground, fragmented clay bricks can be used in concrete as a pozzolanic material.

Evaluation of Relations among Basic Mechanical Properties of Concrete with Machine-Made Sand

2011 ◽  
Vol 418-420 ◽  
pp. 441-444 ◽  
Author(s):  
Feng Lan Li ◽  
Yan Zeng ◽  
Chang Yong Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Rough Surface ◽  
Design Code ◽  
Ordinary Concrete ◽  
Axial Compressive Strength ◽  
Different Characteristics

Due to many different characteristics such as irregular polygon particle with pointed edges, rough surface and larger content of stone powder, machine-made sand has ignorable effects on the properties of concrete. As the basis for the design of concrete structures, the relations among the basic mechanical properties of concrete such as compressive strength, tensile strength, flexural strength and elastic modulus should be clearly understood. This paper summarizes the test data from the published references, and discusses the relations among these properties by statistical analyses compared with those of ordinary concrete. The results show that the axial compressive strength and the tensile strength can be prospected by the same formulas of ordinary concrete specified in current Chinese design code, but the prospected tensile strength should multiply a reducing coefficient when the strength grade of concrete is lower than C30. The elastic modulus of concrete with machine-made sand is larger than that of ordinary concrete, which should be prospect by the formula in this paper. Meanwhile, the formula of flexural strength is suggested.

Literature Review: Properties of Silica Fume Concrete

2014 ◽  
Vol 1004-1005 ◽  
pp. 1516-1522
Author(s):  
Xi Xi He ◽  
Qing Wang
Keyword(s):  
Fracture Toughness ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Silica Fume ◽  
Water Demand ◽  
Interfacial Transition Zone ◽  
Normal Concrete ◽  
Plastic Shrinkage ◽  
Micro Level

Silica fume (SF) modifies interfacial transition zone between cement paste and aggregate at the micro level. Properties of both fresh and hardened silica fume concrete are affected significantly compared to normal concrete. Experiments indicate that concretes become more cohesive and less prone to segregation in the presence of silica fume, moreover, performance of water demand, setting of time, plastic shrinkage varies respectively from concretes without silica fume. Obvious mechanical enhancement of concrete is observed in the aspects of compressive strength tensile strength, elastic modulus as well as fracture toughness.

scholarly journals Characteristics of PVC Coated Welded Wire Mesh Fiber Reinforced Concrete

2019 ◽  
Vol 21 (1) ◽  
pp. 50-56
Author(s):  
Indradi Wijatmiko ◽  
Ari Wibowo ◽  
Christin Remayanti Nainggolan
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fiber Reinforced Concrete ◽  
Wire Mesh ◽  
Fibrous Materials ◽  
Strength Tests ◽  
Fiber Concrete ◽  
Strain Stress ◽  
Mesh Fiber

Fiber concrete containing fibrous materials is manufactured to improve the low tensile strength of concrete and its brittle properties. In this research, fiber obtained from PVC coated welded wire mesh with diameter of 1 mm was utilized. There were several variations of fiber concrete samples made. Samples were subjected to tensile and compressive strength tests. The elastic modulus was measured by using extensometer and strain-stress gauges. The results show that the incorporation of PVC coated welded wire mesh increases the tensile strength of concrete, when the percentage of the fiber is 1.5%, with the length of 3.6cm, and the interlocking of 1.2cm. However, the compressive strength is slightly reduced from the normal ones. The elastic modulus results show that the introduction of PVC coated welded wire mesh tends to reduce the flexibility, as the value reduced 15-50% as compared to the normal ones without any fiber

scholarly journals Study on Mechanical Properties of PET Fiber-Reinforced Coal Gangue Fine Aggregate Concrete

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Yanlin Huang ◽  
An Zhou
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Plain Concrete ◽  
Coal Gangue ◽  
Fine Aggregate ◽  
Replacement Rate ◽  
River Sand ◽  
Aggregate Concrete

In recent years, with the rapid development of the construction industry, the demand for natural river sand has become increasingly prominent. Development of alternatives to river sand has become an interesting direction for concrete research. In this paper, coal gangue was proposed to replace part of the river sand to produce coal gangue fine aggregate concrete, while waste polyethene terephthalate (PET) bottles were used as raw materials to make PET fibers to improve the mechanical properties of coal gangue fine aggregate concrete. There were two parts of the test conducted. In the first part, the compressive strength of the gangue fine aggregate concrete cube, splitting tensile strength, axial compressive strength, and static elastic modulus were studied when the substitution rate of coal gangue increased from 0% to 50%. Referring to the equation of the full stress-strain curve of plain concrete, the stress-strain constitutive equation of coal gangue fine aggregate concrete was analyzed and studied. By comparing with plain concrete, it was found that the coal gangue concrete with a replacement rate of 50% had higher compressive strength and tensile strength, but its brittleness was significantly greater than that of plain concrete in the later stage. In the second part, by studying the effect of different PET fiber content on the mechanical properties of coal gangue fine aggregate concrete with a replacement rate of 50%, it was found that when the addition of PET fiber was 0.1% and 0.3%, not only were compressive strength, splitting tensile strength, static elastic modulus, and flexural strength of the gangue fine aggregate concrete effectively improved but also the brittleness of concrete can be significantly reduced. The study found that after adding 0.3% PET fiber, the coal gangue fine aggregate concrete with a replacement rate of 50% has better mechanical properties and less brittleness.

Experimental Study of the Mechanical Behaviour of Brick Waste Concrete and Analytical Prediction of its Elastic Modulus as a Three-Phase Composite Material

2021 ◽  
Vol 57 ◽  
pp. 125-138
Author(s):  
Wafa Ben Achour ◽  
Saloua El Euch Khay ◽  
Karim Miled ◽  
Jamel Neji
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Mechanical Behaviour ◽  
Mechanical Characteristics ◽  
Splitting Tensile Strength ◽  
Analytical Prediction ◽  
Waste Concrete ◽  
Three Phase ◽  
Substitution Ratio

This paper focuses on the characterization of the mechanical behaviour of concrete incorporating different percentages of brick waste aggregates (BWA). Compressive strength, splitting tensile strength and elastic modulus of this material were measured based on standard laboratory tests and its microstructure was characterized based on scanning electron microscope (SEM) observations. A decrease in these properties was observed with the increase of BWA substitution ratio. However, this decrease remains moderate up to a substitution percentage of 30% (about 12% for compressive strength and elastic modulus and 8% for splitting-tensile strength). In addition, an increase in the concrete porosity was observed with the increase of BWA substitution ratio, which can explain the decrease observed in the measured mechanical characteristics. SEM views on concrete incorporating 100% of BWA showed that the interfacial transition zone (ITZ) and the cement paste present a higher porosity when compared to those of the reference concrete made with natural aggregates.Finally, a micromechanical analytical homogenization model predicting the elastic modulus of brick waste concrete (BWC) according to its composition is proposed where BWC is modelled as a three-phase composite. A good agreement was found between analytical predictions and experimental results proving that BWC mechanical characteristics are mainly governed by BWA mechanical properties and their volume fraction within concrete.

BLENDED METAKAOLIN AND WASTE CLAY BRICK POWDER AS SOURCE MATERIAL IN SUSTAINABLE GEOPOLYMER CONCRETE

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Mahmood F. Ahmed ◽  
Wasan I. Khalil ◽  
Qais J. Frayyeh
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Global Warming ◽  
Source Material ◽  
Geopolymer Concrete ◽  
Construction Sector ◽  
Clay Brick ◽  
Brick Powder ◽  
The World ◽  
The Impact

Recently, sustainability and ecological related problems have attracted more attention around the world. The construction sector incorporates directly and indirectly in global warming, natural resources depletion, and environmental pollution. This study aims, firstly; to identify the optimum mix of metakaolin (MK) geopolymer concrete required to achieve high compressive strength with respect to the concentration of the alkaline solution and curing system. Secondly, to reduce the impact of brick waste on the environment, by producing geopolymer concrete based on blended MK and waste clay brick powder (WBP). The compressive strength, splitting tensile strength and flexural strength of MK-based geopolymer concrete specimens were studied. Different contents of waste clay brick powder (WBP) (0%, 10%, 15%, and 20%) as a replacement by weight of (MK) were investigated. The results appear that it is possible to produce MK-based geopolymer concrete with a compressive strength of 44.03 MPa, while it was 34.76 MPa at 28 days for specimens with 15% WBP replacement of main source binder. Finally, it could be concluded that green moderate strength geopolymer concrete can be produced and used in different civil engineering applications.

Effect of Low Temperature on Mechanical Properties of Concrete with Different Strength Grade

2011 ◽  
Vol 477 ◽  
pp. 308-312 ◽  
Author(s):  
Xiao Ping Cai ◽  
Wen Cui Yang ◽  
Jie Yuan ◽  
Yong Ge ◽  
Bao Sheng Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Low Temperature ◽  
Flexural Strength ◽  
Splitting Tensile Strength ◽  
Growth Ratio ◽  
Strength Grade

The effect of low temperature (-35°C) on the mechanical properties of concrete with different strength grade such as compressive strength, flexural strength, splitting tensile strength and elastic modulus was studied. The results showed that all of the mechanical properties were improved at -35°C. It was also can be found from the tests, as the strength grade increased, the growth ratios at -35°C of compressive strength, flexural strength and splitting tensile strength decreased. But the growth ratio of elastic modulus increased with the increasing of strength grade.

Evaluation of Relations among Basic Mechanical Properties of Fly-Ash Concrete with Machine-Made Sand

2013 ◽  
Vol 438-439 ◽  
pp. 15-19
Author(s):  
Chun Jie Liu ◽  
Chun Yan Jia ◽  
Chang Yong Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Concrete Structures ◽  
Ordinary Concrete ◽  
Strength Grade ◽  
Fly Ash Concrete ◽  
Axial Compressive Strength

Although the machine-made sand was widely used for concrete in recent years in China, it was short of studies on the relations among the basic mechanical properties of fly-ash concrete with machine-made sand (MSFAC). However, these relations such as the compressive strength, the tensile strength and the elastic modulus with the cubic compressive strength (i.e. strength grade) are the basis of design for concrete structures. This paper summarizes the test data from the published references, and discusses the relations among these properties by statistical analyses compared with those of ordinary concrete. The results show that only the tensile strength of MSFAC can be safely forecasted by the same formula of ordinary concrete specified in current Chinese design code. When the strength grade is higher than C45, the axial compressive strength of MSFAC is largely forecasted by the formula of ordinary concrete. The elastic modulus of MSFAC is larger than that of ordinary concrete, which should be prospect by the formula in this paper. This work gives out some cautions for the proper use of the MSFAC in concrete structures.

scholarly journals Influence of fly-ashes on properties of ordinary concretes

2016 ◽  
Vol 48 (1) ◽  
pp. 79-94 ◽  
Author(s):  
Gabriela Rutkowska ◽  
Krzysztof Wiśniewski ◽  
Marek Chalecki ◽  
Mirosława Górecka ◽  
Kamil Miłosek
Keyword(s):  
Sustainable Development ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Building Materials ◽  
Waste Recycling ◽  
Fly Ashes ◽  
Depth Of Penetration ◽  
Air Content ◽  
Water Absorbability ◽  
Made In

Abstract Influence of fly-ashes on properties of ordinary concretes. Care of the environment in accordance with the principles of sustainable development introduces the possibility and need for waste recycling. The construction and building materials industry has the greatest potential for reuse of waste. The article presents the results of investigations of selected properties (consistency, water absorbability, compressive strength and tensile strength after 28 and 56 days of curing, depth of penetration) of ordinary concretes and concretes containing fly-ashes - calcareous and siliceous ash − in their composition. To make the samples, the Portland cement CEM I 42.5 R and natural aggregate with graining of 0-16 mm were used. The concrete with siliceous and calcareous admixtures was made in three lots where the ash was added in the quantity of 15, 20 and 30% of the cement mass. After the tests, it was stated that the fly-ash admixture does not increase the air content in the mix, it increases the compressive strength in time and the siliceous ash improves the splitting tensile strength.

Sign in / Sign up

Export Citation Format

Share Document