scholarly journals Characteristics of PVC Coated Welded Wire Mesh Fiber Reinforced Concrete

2019 ◽  
Vol 21 (1) ◽  
pp. 50-56
Author(s):  
Indradi Wijatmiko ◽  
Ari Wibowo ◽  
Christin Remayanti Nainggolan
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fiber Reinforced Concrete ◽  
Wire Mesh ◽  
Fibrous Materials ◽  
Strength Tests ◽  
Fiber Concrete ◽  
Strain Stress ◽  
Mesh Fiber

Fiber concrete containing fibrous materials is manufactured to improve the low tensile strength of concrete and its brittle properties. In this research, fiber obtained from PVC coated welded wire mesh with diameter of 1 mm was utilized. There were several variations of fiber concrete samples made. Samples were subjected to tensile and compressive strength tests. The elastic modulus was measured by using extensometer and strain-stress gauges. The results show that the incorporation of PVC coated welded wire mesh increases the tensile strength of concrete, when the percentage of the fiber is 1.5%, with the length of 3.6cm, and the interlocking of 1.2cm. However, the compressive strength is slightly reduced from the normal ones. The elastic modulus results show that the introduction of PVC coated welded wire mesh tends to reduce the flexibility, as the value reduced 15-50% as compared to the normal ones without any fiber

Research on the Basic Mechanical Properties of Fly Ash Fiber Reinforced Concrete

2011 ◽  
Vol 261-263 ◽  
pp. 8-12
Author(s):  
Shu Shan Li ◽  
Ming Xiao Jia ◽  
Dan Ying Gao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Compressive Modulus ◽  
Fiber Reinforced Concrete ◽  
Cement Ratio ◽  
Influence Mechanism ◽  
Fiber Concrete ◽  
Early Strength

The basic mechanical properties of fly ash fiber concrete were tested. The influences to the compressive strength, splitting tensile strength and compressive modulus of elasticity of fiber concrete by water-cement ratio, dosage of fly ash and other factors were analyzed. The influence mechanism of fly ash to concrete is discussed. The results indicate that with the increase of the dosage of fly ash, the early strength of double-doped concrete is reduced, while the later strength of concrete was obviously increased.

scholarly journals Tests on workability and strength of high strength-flowable concrete containing PET waste fiber

2020 ◽  
Vol 7 (3) ◽  
pp. 115-139
Author(s):  
Sarkawt Karim ◽  
◽  
Azad Mohammed ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fiber Length ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Time Increase ◽  
Fiber Volume ◽  
Split Tensile Strength ◽  
Pet Waste ◽  
Strength Tests

This study describes two workability tests, compressive strength and tensile strength tests of high strength flowable concrete containing plastic fiber prepared from polyethylene terephthalate (PET) waste bottles. For the high fluidity mix Vebe time and V-funnel time tests were carried out. Results show that there is a Vebe time increase with PET fiber addition to concrete being increased with increasing fiber volume and fiber length. V-funnel time was found to reduce when up to 0.75% fiber volume is added to concrete, followed by an increase for larger fiber volumes. When fiber length is increase, there is more time increase, but in general, V-funnel time increase was lower than that of Vebe time, indicating a different influence of PET fiber on the compatibility and flowability. The measured V-funnel time for all mixes was found to conform to the limits of European specifications on the flowability of self compacting concrete. Small descending in compressive strength was recorded for RPET fiber reinforced concrete that reached 15.74 % for 1.5 percent fiber content with 10 mm fiber length. Attractive results was recorded in split tensile strength of RPET fibrous samples which resulted in improvement up to 63.3 % for 1.5 percent of 40 mm fiber length content.

scholarly journals Effects of Single and Hybrid Steel Fiber Lengths and Fiber Contents on the Mechanical Properties of High-Strength Fiber-Reinforced Concrete

2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Kyoung-Chul Kim ◽  
In-Hwan Yang ◽  
Changbin Joh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Steel Fiber ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Experimental Parameters ◽  
High Strength Fiber

This paper describes an experimental study on the mechanical properties of high-strength fiber-reinforced concrete (HSFRC). The experimental parameters included the content and length of the steel fiber as well as the use of either a single-type fiber or hybrid steel fibers. The steel fiber contents were 1.0, 1.5, and 2.0% based on the volume of HSFRC, and the steel fiber lengths were 13, 16.5, and 19.5 mm. In addition, hybrid steel fibers incorporating steel fibers of different lengths were used. Compression tests and crack mouth opening displacement tests were performed for each HSFRC mixture with different experimental parameters. The mechanical properties of the HSFRC, such as compressive strength, elastic modulus, and tensile strength, increased with the steel fiber content. The mechanical property results of the HSFRC mixture using a single fiber length of 13 mm were greater than the results of the other mixtures. The compressive strength, elastic modulus, and tensile strength of the HSFRC mixture with hybrid steel fibers were similar to those of the mixtures with a single length of steel fiber. Additionally, based on the test results of the material properties, equations for predicting the elastic modulus and tensile strength of the HSFRC were suggested; the predictions using the proposed formula closely agreed with the experimental results.

scholarly journals Compressive Strength and Elastic Modulus of Slurry Infiltrated Fiber Concrete (SIFCON) at High Temperature

2020 ◽  
Vol 6 (2) ◽  
pp. 265-275 ◽  
Author(s):  
Ali Mudhafar Hashim ◽  
Mohammed Mansour Kadhum
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
High Temperatures ◽  
Fiber Reinforced Concrete ◽  
High Fiber ◽  
Fiber Concrete ◽  
Before And After ◽  
Temperature Ranges ◽  
Fire Flame ◽  
Increasing Temperature

SIFCON is a special type of fiber reinforced concrete (FRC) with an unattached fiber matrix that gives the composite matrix important tensile properties and, due to its high fiber content, SIFCON also has distinctive and unique ductility and energy absorption properties. Higher temperature resistance is one of the most important parameters affecting the durability and service life of the material. In this research, the compression strength and elastic modulus of Slurry Infiltrated Fiber Concrete (SIFCON) were tested both before and after exposure to high temperatures. Two fire exposure durations of 2 and 3 hours are examined. In addition to room temperatures, three temperature ranges of 400 ° C, 600 ° C and 900 ° C have been introduced. The results of the experiment showed that the compressive strength and elastic modulus decreased after exposure to high temperatures. The drastically reduction of compressive strength took place with increasing temperature above 600 °C. While, the reduction in elastic modulus values is more significant than the decrease in compressive strength at the same fire flame temperatures. The residual compressive strength and elastic modulus at 900 °C were in the range of (52.1% to 59.6%) and (30.6% to 34.1%) respectively.

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

APPLICATION OF OIL PALM EMPTY FRUIT BUNCH FIBERS IN STRENGTH IMPROVEMENT AS A FIBER REINFORCED CONCRETE

2017 ◽  
Vol 25 (3) ◽  
pp. 161-170
Author(s):  
Henny Lydiasari ◽  
Ari Yusman Manalu ◽  
Rahmi Karolina
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Crack Length ◽  
Oil Palm ◽  
Fiber Reinforced Concrete ◽  
Structural Concrete ◽  
Empty Fruit Bunches ◽  
Construction Products ◽  
By Products ◽  
Strength Improvement

The potency of oil palm empty fruit bunches (OPEFB) fibers as one of the by-products of processing oil palm is increasing significantly so that proper management is needed in reducing environmental impact. One of the utilization of OPEFB fibers is as a substitution material in construction which usually the material is derived from non-renewable mining materials so that the number is increasingly limited. Therefore, it is necessary to study to know the performance of OPEFB fiber in making construction products especially concrete. In this case, the experiment was conducted using experimental method with variation of fiber addition by 0%, 10%, 15%, 20%, 25%, and 30%. Each specimen was tested by weight, slump value, compressive strength, tensile strength, elasticity and crack length. As the results, the variation of fibers addition by 10%, decrease of slump value is 7%, concrete weight is 3% and crack length is 8% while increase of the compressive strength is 2.7% and the modulus of elasticity is 33.3% but its tensile strength decreased insignificantly by 0.05% . Furthermore, the addition of fibers above 10% to 30% decreased compressive strength is still below 10% and tensile strength below 2% while the weight of concrete, slump value and crack length decreased. Therefore, the addition of 10% can replace the performance of concrete without fiber but the addition of above 10% can still be used on non-structural concrete.

scholarly journals Clay-Based Products Sustainable Development: Some Applications

2021 ◽  
Vol 13 (3) ◽  
pp. 1364
Author(s):  
Michele La Noce ◽  
Alessandro Lo Faro ◽  
Gaetano Sciuto
Keyword(s):  
Sustainable Development ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Basalt Fibers ◽  
Future Studies ◽  
Clay Bricks ◽  
Brick Powder ◽  
Alkaline Resistance ◽  
Raw Earth

Clay has a low environmental impact and can develop into many different products. The research presents two different case studies. In the first, the clay is the binder of raw earth doughs in order to produce clay-bricks. We investigate the effects of natural fibrous reinforcements (rice straws and basalt fibers) in four different mixtures. From the comparison with a mix without reinforcements, it is possible to affirm that the 0.40% of basalt fibers reduce the shrinkage by about 25% and increase the compressive strength by about 30%. Future studies will focus on identifying the fibrous effects on tensile strength and elastic modulus, as well as the optimal percentage of fibers. In the second study, the clay, in form of brick powder (“cocciopesto”), gives high alkaline resistance and breathability performance, as well as rendering and color to the plaster. The latter does not have artificial additives. The plaster respects the cultural instance of the original building. The research underlines how the use of a local (and traditional) material such as clay can be a promoter of sustainability in the contemporary building sector. Future studies must investigate further possible uses of clay as well as a proper regulatory framework.

Test Comparison Research Mechanics Performance between Sisal Fiber Concrete and Rubber Powder Concrete

2011 ◽  
Vol 243-249 ◽  
pp. 494-498
Author(s):  
Hui Ming Bao
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Sisal Fiber ◽  
Environment Friendly ◽  
Rubber Powder ◽  
Comparison Research ◽  
Mechanics Performance ◽  
Fiber Concrete ◽  
Sisal Fibers

By means of the tests on the mechanics performance of the reinforcing concrete mixed with sisal fibers or rubber powder of certain content are investigated. The compressive strength, tensile strength and flexural strength, etc. are compared. The test indicates that when the test condition is same, the compressive strength, tensile strength and flexural strength of the sisal fibers concrete are better than those of the rubber powder’s. The sisal fiber concrete is environment friendly than the rubber powder concrete. And it has widely value of spread and utilization.

scholarly journals Assessment of the mechanical properties of glass ionomer cements for orthodontic cementation

2012 ◽  
Vol 17 (6) ◽  
pp. 154-159 ◽  
Author(s):  
Marcel M. Farret ◽  
Eduardo Martinelli de Lima ◽  
Eduardo Gonçalves Mota ◽  
Hugo Mitsuo S. Oshima ◽  
Gabriela Maguilnik ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Bond Strength ◽  
Shear Bond Strength ◽  
Glass Ionomer Cements ◽  
Glass Ionomer ◽  
Resin Modified Glass Ionomer ◽  
Strength Tests ◽  
Diametral Tensile Strength

OBJECTIVE: To evaluate the mechanical properties of three glass ionomers cements (GICs) used for band cementation in Orthodontics. METHODS: Two conventional glass ionomers (Ketac Cem Easy mix/3M-ESPE and Meron/Voco) and one resin modified glass ionomer (Multi-cure Glass ionomer/3M-Unitek) were selected. For the compressive strength and diametral tensile strength tests, 12 specimens were made of each material. For the microhardness test 15 specimens were made of each material and for the shear bond strength tests 45 bovine permanent incisors were used mounted in a self-cure acrylic resin. Then, band segments with a welded bracket were cemented on the buccal surface of the crowns. For the mechanical tests of compressive and diametral tensile strength and shear bond strength a universal testing machine was used with a crosshead speed of 1,0 mm/min and for the Vickers microhardness analysis tests a Microdurometer was used with 200 g of load during 15 seconds. The results were submitted to statistical analysis through ANOVA complemented by Tukey's test at a significance level of 5%. RESULTS: The results shown that the Multi-Cure Glass Ionomer presented higher diametral tensile strength (p < 0.01) and compressive strength greater than conventional GICs (p = 0.08). Moreover, Ketac Cem showed significant less microhardness (p < 0.01). CONCLUSION: The resin-modified glass ionomer cement showed high mechanical properties, compared to the conventional glass ionomer cements, which had few differences between them.

scholarly journals Investigation on Mechanical and Durability Properties of Rapid Strength Gaining Concrete

2018 ◽  
Vol 7 (2.12) ◽  
pp. 406
Author(s):  
L Krishnaraj ◽  
P T. Ravichandran ◽  
Shaik AarifIlahi ◽  
V Ramanathan
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Cement Paste ◽  
Mechanical Tests ◽  
High Rate ◽  
Concrete Technology ◽  
Strength Concrete ◽  
Durability Properties ◽  
Content Ratio ◽  
Strength Tests

The strength of cement paste and aggregate components helps to decide the strength of the concrete, their properties of deformation, and the binding properties among the aggregate surface and cement paste. It is conceivable with many of the aggregates to form high strength concrete by increasing the cement paste strength, which can be controlled by choosing of water-content ratio and type of admixture dosage. The current scenario in the concrete technology and the accessibility of many kind of mineral and chemical admixtures, and special super plasticizer to gain the targeted compressive strength of a concrete. In this study MYK Remicrete PC30 and BASF Master Glennium ACE 30 were utilized as the admixtures as Add 1 and Add 2 which acts as high rate water reducing agents. These developments have led to increase uses of Rapid strength concrete. To compare the mechanical and durability properties of concrete using Fly ash and Admixtures the following tests were conducted on concrete tests specimens. Mechanical tests are to be conducted such as compressive strength tests, and tensile strength tests, durability tests like water absorption test, acid test by HCL, H2SO4 and HNO3. The result indicates that rate of development of compressive strength and tensile strength are higher for the concrete design mix which has HRWR admixture of 1% and FA of 20%.  

Sign in / Sign up

Export Citation Format

Share Document