scholarly journals Shershnev coefficient is a basic characteristic of the structure of a crystallizing network polymer

2021 ◽  
pp. 4-5
Author(s):  
V. V. Kovriga ◽  
T. F. Oreshenkova ◽  
I. N. Pyatin

The values of molecular weight between nodes in cross-linked polyethylene obtained by the method of swelling and the method of determining the equilibrium modulus are considered. It has been shown that it is not possible to achieve uniform values of molecular weight between mesh points using these two methods. The ratio between the molecular weights located between the nodes of the network, it is proposed to call the "Shershnev coefficient".

1957 ◽  
Vol 30 (1) ◽  
pp. 54-60
Author(s):  
G. M. Bartenev ◽  
A. S. Novikov ◽  
F. A. Galil-Ogly

Abstract (1) With decrease of the original molecular weight of rubber, there is a parallel decrease of the durability of its vulcanizates when they contain the same percentage of combined sulfur. On the other hand, this decrease of durability with decrease of the original molecular weight is only slight for vulcanizates having the same equilibrium modulus, i.e., the same density of crosslinks in the three-dimensional network. (2) In dynamic testing which involves repeated stretching, the durability depends on the testing conditions when the vulcanizates contain the same percentage of combined sulfur and at the same time when either the original molecular weight of the rubber is low or the equilibrium modulus is small. On the contrary, when the original molecular weight or the modulus is high, the durability does not depend on the testing conditions. When vulcanizates have the same equilibrium modulus, their durability depends on the original molecular weight. In this latter case the durability increases with increase of the molecular weight, independent of the testing conditions (given maximum load, given maximum deformation, etc.), and reaches a practically constant value at high molecular weights. (3) The fundamental influence of the original molecular weight on the strength and dynamic durability of vulcanizates containing the same percentage of combined sulfur is manifest in the retardation of the formation of a spatial network in low-molecular rubbers when vulcanized. With rubber of low original molecular weight, vulcanization leads to the formation of a thin space network and consequently a large number of molecular chain ends outside the network. For this reason, vulcanizates of low-molecular rubbers when tested are characterized by high permanent set.


1959 ◽  
Vol 32 (3) ◽  
pp. 651-661
Author(s):  
E. V. Kuvshinskiĭ ◽  
M. M. Fomicheva

Abstract 1. Studied were the moduli of resilience and rebound elasticity of the vulcanized rubbers made from fractions of butadiene-styrene rubber “SKS-30-A” at temperatures of 20, 60, and 100° C in the region of molecular weights from 45,000 to 620,000 with various degrees of vulcanization (with variation in the pseudoequilibrium modulus from 5 to 70 kg/cm2). 2. The dynamic modulus of resilience is little dependent on the molecular weight of the original rubber both at room temperature and at higher temperatures. 3. At higher temperatures the elasticity of vulcanized rubber is mainly determined by the degree of vulcanization, the measure of which is the pseudo-equilibrium modulus, and is little dependent on the initial molecular weight. At low temperatures (20° C) elasticity increases with the degree of vulcanization, but it increases at different rates for vulcanized rubbers made from fractions with different molecular weights. At 20° C the increase in the degree of vulcanization increases the elasticity of vulcanized rubbers made from low-molecular fractions (45,000) to a lower degree than of those made from high molecular weight fractions (above 133,000). 4. The value of the maximum elasticity of vulcanized rubbers obtained from rubbers of the same molecular weight is not dependent on the type of accelerator used.


1954 ◽  
Vol 27 (4) ◽  
pp. 925-929 ◽  
Author(s):  
A. S. Novikov ◽  
G. M. Bartenev ◽  
F. A. Galil-Ogly

Abstract From scientific literature it is known that the rate of vulcanization and the mechanical properties of rubbers depend on the value of the initial molecular weight of the rubber. However, the cause of the slow vulcanization of olw molecular rubbers and the effect of the molecular weight of the rubber on the formation of a spatial network and the structure of the vulcanizate remain unclear. In the present work the kinetics of vulcanization of separate fractions of butadiene rubber SKS-30A of molecular weight from 100,000 to 1,170,000 was studied by measurements of the equilibrium modulus and the proportion of combined sulfur. The SKS-30A rubber was divided into five fractions of molecular weights: I 1,170,000; II 700,000; III 500,000; IV 140,000; and V 100,000. The molecular weights were calculated from viscometric data according to the formula previously established for this rubber by the authors: [η]=2.96×10−4 M0.71. In order to keep the molecular weight of the rubber constant, sheets for vulcanization were prepared from a dispersion of the ingredients in a benzene-rubber solution. The composition of the mixture was the same for all the fractions, i.e., 100 parts by weight of rubber, 3 parts of sulfur, 1 part of mercapto-benzothiazole, 5 parts of zinc oxide, 2 parts of stearic acid, and 1 part of phenyl-β-naphthylamine. The sheets were vulcanized in a hydraulic press at 143° C for various periods. The amount of sulfur combined with the rubber was determined by Bolotnikov's method, specially adapted to small batches of vulcanizate. The rubber specimens, weighing 0.2–0.3 gram, were extracted in 50 cc. of sodium sulfide, and titrated with 0.01N iodine solution.


1988 ◽  
Vol 60 (01) ◽  
pp. 107-112 ◽  
Author(s):  
Roy Harris ◽  
Louis Garcia Frade ◽  
Lesley J Creighton ◽  
Paul S Gascoine ◽  
Maher M Alexandroni ◽  
...  

SummaryThe catabolism of recombinant tissue plasminogen activator (rt-PA) was investigated after injection of radiolabelled material into rats. Both Iodogen and Chloramine T iodination procedures yielded similar biological activity loss in the resultant labelled rt-PA and had half lives in the rat circulation of 1 and 3 min respectively. Complex formation of rt-PA was investigated by HPLC gel exclusion (TSK G3000 SW) fractionation of rat plasma samples taken 1-2 min after 125I-rt-PA injection. A series of radiolabelled complexes of varying molecular weights were found. However, 60% of the counts were associated with a single large molecular weight complex (350–500 kDa) which was undetectable by immunologically based assays (ELISA and BIA) and showed only low activity with a functional promoter-type t-PA assay. Two major activity peaks in the HPLC fractions were associated with Tree t-PA and a complex having a molecular weight of ̴ 180 kDa. HPLC fractionation to produce these three peaks at various timed intervals after injection of 125I-rt-PA showed each to have a similar initial rate half life in the rat circulation of 4-5 min. The function of these complexes as yet is unclear but since a high proportion of rt-PA is associated with a high molecular weight complex with a short half life in the rat, we suggest that the formation of this complex may be a mechanism by which t-PA activity is initially regulated and finally cleared from the rat circulation.


1981 ◽  
Vol 45 (01) ◽  
pp. 090-094 ◽  
Author(s):  
Katsuo Sueishi ◽  
Shigeru Nanno ◽  
Kenzo Tanaka

SummaryFibrinogen degradation products were investigated for leukocyte chemotactic activity and for enhancement of vascular permeability. Both activities increased progressively with plasmin digestion of fibrinogen. Active fragments were partially purified from 24 hr-plasmin digests. Molecular weights of the permeability increasing and chemotactic activity fractions were 25,000-15,000 and 25,000 respectively. Both fractions had much higher activities than the fragment X, Y, D or E. Electron microscopic observation of the small blood vessels in rabbit skin correlated increased permeability with the formation of characteristic gaps between adjoining endothelial cells and their contraction.These findings suggest that lower molecular weight degradation products of fibrinogen may be influential in contributing to granulocytic infiltration and enhanced permeability in lesions characterized by deposits of fibrin and/or fibrinogen.


1964 ◽  
Vol 12 (01) ◽  
pp. 232-261 ◽  
Author(s):  
S Sasaki ◽  
T Takemoto ◽  
S Oka

SummaryTo demonstrate whether the intravascular precipitation of fibrinogen is responsible for the toxicity of heparinoid, the relation between the toxicity of heparinoid in vivo and the precipitation of fibrinogen in vitro was investigated, using dextran sulfate of various molecular weights and various heparinoids.1. There are close relationships between the molecular weight of dextran sulfate, its toxicity, and the quantity of fibrinogen precipitated.2. The close relationship between the toxicity and the precipitation of fibrinogen found for dextran sulfate holds good for other heparinoids regardless of their molecular structures.3. Histological findings suggest strongly that the pathological changes produced with dextran sulfate are caused primarily by the intravascular precipitates with occlusion of the capillaries.From these facts, it is concluded that the precipitates of fibrinogen with heparinoid may be the cause or at least the major cause of the toxicity of heparinoid.4. The most suitable molecular weight of dextran sulfate for clinical use was found to be 5,300 ~ 6,700, from the maximum value of the product (LD50 · Anticoagulant activity). This product (LD50 · Anticoagulant activity) can be employed generally to assess the comparative merits of various heparinoids.5. Clinical use of the dextran sulfate prepared on this basis gave satisfactory results. No severe reaction was observed. However, two delayed reactions, alopecia and thrombocytopenia, were observed. These two reactions seem to come from the cause other than intravascular precipitation.


1962 ◽  
Vol 08 (02) ◽  
pp. 270-275 ◽  
Author(s):  
David L Aronson ◽  
John W Preiss ◽  
Michael W Mosesson

SummaryThe molecular weights of AHF (factor VIII) and of PTC (factor IX) have been estimated by their sensitivity to inactivation by 7 kilovolt electrons. The molecular weight of AHF was found to be 180 000 by this method and that of PTC was found to be 110 000.


Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 850
Author(s):  
Donghyuk Kim ◽  
Byungkyu Ahn ◽  
Kihyun Kim ◽  
JongYeop Lee ◽  
Il Jin Kim ◽  
...  

Liquid butadiene rubber (LqBR) which used as a processing aid play a vital role in the manufacturing of high-performance tire tread compounds. However, the studies on the effect of molecular weight, microstructure, and functionalization of LqBR on the properties of compounds are still insufficient. In this study, non-functionalized and center-functionalized liquid butadiene rubbers (N-LqBR and C-LqBR modified with ethoxysilyl group, respectively) were synthesized with low vinyl content and different molecular weights using anionic polymerization. In addition, LqBR was added to the silica-filled SSBR compounds as an alternative to treated distillate aromatic extract (TDAE) oil, and the effect of molecular weight and functionalization on the properties of the silica-filled SSBR compound was examined. C-LqBR showed a low Payne effect and Mooney viscosity because of improved silica dispersion due to the ethoxysilyl functional group. Furthermore, C-LqBR showed an increased crosslink density, improved mechanical properties, and reduced organic matter extraction compared to the N-LqBR compound. LqBR reduced the glass transition temperature (Tg) of the compound significantly, thereby improving snow traction and abrasion resistance compared to TDAE oil. Furthermore, the energy loss characteristics revealed that the hysteresis loss attributable to the free chain ends of LqBR was dominant.


1977 ◽  
Vol 72 (1) ◽  
pp. 194-208 ◽  
Author(s):  
L D Hodge ◽  
P Mancini ◽  
F M Davis ◽  
P Heywood

A subnuclear fraction has been isolated from HeLa S3 nuclei after treatment with high salt buffer, deoxyribonuclease, and dithiothreitol. This fraction retains the approximate size and shape of nuclei and resembles the nuclear matrix recently isolated from rat liver nuclei. Ultrastructural and biochemical analyses indicate that this structure consists of nonmembranous elements as well as some membranous elements. Its chemical composition is 87% protein, 12% phospholipid, 1% DNA, and 0.1% RNA by weight. The protein constituents are resolved in SDS-polyacrylamide slab gels into 30-35 distinguishable bands in the apparent molecular weight range of 14,000 - 200,000 with major peptides at 14,000 - 18,000 and 45,000 - 75,000. Analysis of newly synthesized polypeptides by cylindrical gel electrophoresis reveals another cluster in the 90,000-130,000 molecular weight range. Infection with adenovirus results in an altered polypeptide profile. Additional polypeptides with apparent molecular weights of 21,000, 23,000, and 92,000 become major components by 22 h after infection. Concomitantly, some peptides in the 45,000-75,000 mol wt range become less prominent. In synchronized cells the relative staining capacity of the six bands in the 45,000-75,000 mol wt range changes during the cell cycle. Synthesis of at least some matrix polypeptides occures in all phases of the cell cycle, although there is decreased synthesis in late S/G2. In the absence of protein synthesis after cell division, at least some polypeptides in the 45,000-75,000 mol wt range survive nuclear dispersal and subsequent reformation during mitosis. The possible significance of this subnuclear structure with regard to structure-function relationships within the nucleus during virus replication and during the life cycle of the cell is discussed.


Molecules ◽  
2019 ◽  
Vol 24 (6) ◽  
pp. 1049 ◽  
Author(s):  
Rosalía Rodríguez-Dorado ◽  
Clara López-Iglesias ◽  
Carlos García-González ◽  
Giulia Auriemma ◽  
Rita Aquino ◽  
...  

Processing and shaping of dried gels are of interest in several fields like alginate aerogel beads used as highly porous and nanostructured particles in biomedical applications. The physicochemical properties of the alginate source, the solvent used in the gelation solution and the gel drying method are key parameters influencing the characteristics of the resulting dried gels. In this work, dried gel beads in the form of xerogels, cryogels or aerogels were prepared from alginates of different molecular weights (120 and 180 kDa) and concentrations (1.25, 1.50, 2.0 and 2.25% (w/v)) using different gelation conditions (aqueous and ethanolic CaCl2 solutions) and drying methods (supercritical drying, freeze-drying and oven drying) to obtain particles with a broad range of physicochemical and textural properties. The stability of physicochemical properties of alginate aerogels under storage conditions of 25 °C and 65% relative humidity (ICH-climatic zone II) during 1 and 3 months was studied. Results showed significant effects of the studied processing parameters on the resulting alginate dried gel properties. Stability studies showed small variations in aerogels weight and specific surface area after 3 months of storage, especially, in the case of aerogels produced with medium molecular weight alginate.


Sign in / Sign up

Export Citation Format

Share Document